diff options
Diffstat (limited to 'u-boot/include/configs/CPCI405.h')
| -rw-r--r-- | u-boot/include/configs/CPCI405.h | 342 |
1 files changed, 342 insertions, 0 deletions
diff --git a/u-boot/include/configs/CPCI405.h b/u-boot/include/configs/CPCI405.h new file mode 100644 index 0000000..426fc57 --- /dev/null +++ b/u-boot/include/configs/CPCI405.h @@ -0,0 +1,342 @@ +/* + * (C) Copyright 2001 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405 CPU */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */ + +#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#undef CONFIG_BOOTARGS +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PCI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_IDE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_ELF +#define CONFIG_CMD_MII +#define CONFIG_CMD_EEPROM + + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_SUPPORT_VFAT + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CONFIG_SYS_BASE_BAUD 691200 + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_LOOPW 1 /* enable loopw command */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ + +#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ +#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ + +#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + *----------------------------------------------------------------------- + */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_RESET /* no reset for ide supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ + +#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ +#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ +#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/ + +#if 1 /* Use NVRAM for environment variables */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ +#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ +#define CONFIG_ENV_ADDR \ + (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ + +#else /* Use EEPROM for environment variables */ + +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CONFIG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */ + /* total size of a CAT24WC08 is 1024 bytes */ +#endif + +/*----------------------------------------------------------------------- + * I2C EEPROM (CAT24WC08) for environment + */ +#define CONFIG_HARD_I2C /* I2c with hardware support */ +#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ + /* 16 byte page write mode using*/ + /* last 4 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ + +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (Flash Bank 1) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x92015480 +#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 3 (CompactFlash IDE) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ + +/* Memory Bank 4 (NVRAM) initialization */ +#define CONFIG_SYS_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */ +#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 5 (Quart) initialization */ +#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/ +#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ + +/*----------------------------------------------------------------------- + * FPGA stuff + */ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +#if 1 /* test-only */ +#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */ + +#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */ +#else +#define CONFIG_SYS_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */ +#endif +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#endif /* __CONFIG_H */ |