diff options
Diffstat (limited to 'u-boot/include/configs/M5373EVB.h')
| -rw-r--r-- | u-boot/include/configs/M5373EVB.h | 275 |
1 files changed, 275 insertions, 0 deletions
diff --git a/u-boot/include/configs/M5373EVB.h b/u-boot/include/configs/M5373EVB.h new file mode 100644 index 0000000..7086a1b --- /dev/null +++ b/u-boot/include/configs/M5373EVB.h @@ -0,0 +1,275 @@ +/* + * Configuation settings for the Freescale MCF5373 FireEngine board. + * + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. + * TsiChung Liew (Tsi-Chung.Liew@freescale.com) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _M5373EVB_H +#define _M5373EVB_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCF532x /* define processor family */ +#define CONFIG_M5373 /* define processor type */ + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT (0) +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG +#define CONFIG_WATCHDOG_TIMEOUT 3360 /* timeout in ms, max is 3.36 sec */ + +/* Command line configuration */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#ifdef NANDFLASH_SIZE +# define CONFIG_CMD_NAND +#endif + +#define CONFIG_SYS_UNIFY_CACHE + +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CONFIG_MII_INIT 1 +# define CONFIG_SYS_DISCOVER_PHY +# define CONFIG_SYS_RX_ETH_BUFFER 8 +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN + +# define CONFIG_SYS_FEC0_PINMUX 0 +# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CONFIG_SYS_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CONFIG_SYS_DISCOVER_PHY */ +#endif + +#define CONFIG_MCFRTC +#undef RTC_DEBUG + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C /* I2C with hw support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SPEED 80000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR + +#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ +#define CONFIG_UDP_CHECKSUM + +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* FEC_ENET */ + +#define CONFIG_HOSTNAME M5373EVB +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off 0 2ffff;" \ + "era 0 2ffff;" \ + "cp.b ${loadaddr} 0 ${filesize};" \ + "save\0" \ + "" + +#define CONFIG_PRAM 512 /* 512 KB */ +#define CONFIG_SYS_PROMPT "-> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ + +#ifdef CONFIG_CMD_KGDB +# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x40010000 + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 80000000 +#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 3 + +#define CONFIG_SYS_MBAR 0xFC000000 + +#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000) + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ +#define CONFIG_SYS_SDRAM_CFG1 0x53722730 +#define CONFIG_SYS_SDRAM_CFG2 0x56670000 +#define CONFIG_SYS_SDRAM_CTRL 0xE1092000 +#define CONFIG_SYS_SDRAM_EMOD 0x40010000 +#define CONFIG_SYS_SDRAM_MODE 0x018D0000 + +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 +#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) + +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ + +#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) +#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_FLASH_CFI +#ifdef CONFIG_SYS_FLASH_CFI +# define CONFIG_FLASH_CFI_DRIVER 1 +# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ +# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +#endif + +#ifdef NANDFLASH_SIZE +# define CONFIG_SYS_MAX_NAND_DEVICE 1 +# define CONFIG_SYS_NAND_BASE CONFIG_SYS_CS2_BASE +# define CONFIG_SYS_NAND_SIZE 1 +# define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +# define NAND_ALLOW_ERASE_ALL 1 +# define CONFIG_JFFS2_NAND 1 +# define CONFIG_JFFS2_DEV "nand0" +# define CONFIG_JFFS2_PART_SIZE (CONFIG_SYS_CS2_MASK & ~1) +# define CONFIG_JFFS2_PART_OFFSET 0x00000000 +#endif + +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH 1 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 16 + +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ + CF_CACR_DCM_P) + +/*----------------------------------------------------------------------- + * Chipselect bank definitions + */ +/* + * CS0 - NOR Flash 1, 2, 4, or 8MB + * CS1 - CompactFlash and registers + * CS2 - NAND Flash 16, 32, or 64MB + * CS3 - Available + * CS4 - Available + * CS5 - Available + */ +#define CONFIG_SYS_CS0_BASE 0 +#define CONFIG_SYS_CS0_MASK 0x007f0001 +#define CONFIG_SYS_CS0_CTRL 0x00001fa0 + +#define CONFIG_SYS_CS1_BASE 0x10000000 +#define CONFIG_SYS_CS1_MASK 0x001f0001 +#define CONFIG_SYS_CS1_CTRL 0x002A3780 + +#ifdef NANDFLASH_SIZE +#define CONFIG_SYS_CS2_BASE 0x20000000 +#define CONFIG_SYS_CS2_MASK ((NANDFLASH_SIZE << 20) | 1) +#define CONFIG_SYS_CS2_CTRL 0x00001f60 +#endif + +#endif /* _M5373EVB_H */ |