diff options
Diffstat (limited to 'u-boot/include/configs/PK1C20.h')
| -rw-r--r-- | u-boot/include/configs/PK1C20.h | 243 |
1 files changed, 243 insertions, 0 deletions
diff --git a/u-boot/include/configs/PK1C20.h b/u-boot/include/configs/PK1C20.h new file mode 100644 index 0000000..b466c4b --- /dev/null +++ b/u-boot/include/configs/PK1C20.h @@ -0,0 +1,243 @@ +/* + * (C) Copyright 2004, Psyent Corporation <www.psyent.com> + * Scott McNutt <smcnutt@psyent.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*------------------------------------------------------------------------ + * BOARD/CPU + *----------------------------------------------------------------------*/ +#define CONFIG_PK1C20 1 /* PK1C20 board */ +#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ + +#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */ +#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ +#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/ + +/*------------------------------------------------------------------------ + * CACHE -- the following will support II/s and II/f. The II/s does not + * have dcache, so the cache instructions will behave as NOPs. + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */ +#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */ +#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ +#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ + +/*------------------------------------------------------------------------ + * MEMORY BASE ADDRESSES + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */ +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ +#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */ +#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */ +#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */ +#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/ + +/*------------------------------------------------------------------------ + * MEMORY ORGANIZATION + * -Monitor at top. + * -The heap is placed below the monitor. + * -Global data is placed below the heap. + * -The stack is placed below global data (&grows down). + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 128k */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET + +/*------------------------------------------------------------------------ + * FLASH (AM29LV065D) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size */ + +/*------------------------------------------------------------------------ + * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above + * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the + * reset address, no? This will keep the environment in user region + * of flash. NOTE: the monitor length must be multiple of sector size + * (which is common practice). + *----------------------------------------------------------------------*/ +#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */ +#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ +#define CONFIG_ENV_OVERWRITE /* Serial change Ok */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN) + +/*------------------------------------------------------------------------ + * CONSOLE + *----------------------------------------------------------------------*/ +#define CONFIG_ALTERA_UART 1 /* Use altera uart */ +#if defined(CONFIG_ALTERA_JTAG_UART) +#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ +#else +#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */ +#endif + +#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ +#define CONFIG_BAUDRATE 115200 /* Initial baudrate */ +#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ + +/*------------------------------------------------------------------------ + * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for + * epcs device access is enabled. The base address is the epcs + * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK. + * The register base is currently at offset 0x600 from the memory base. + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_NIOS_EPCSBASE 0x02100200 /* EPCS register base */ + +/*------------------------------------------------------------------------ + * DEBUG + *----------------------------------------------------------------------*/ +#undef CONFIG_ROM_STUBS /* Stubs not in ROM */ + +/*------------------------------------------------------------------------ + * TIMEBASE -- + * + * The high res timer defaults to 1 msec. Since it includes the period + * registers, the interrupt frequency can be reduced using TMRCNT. + * If the default period is acceptable, TMRCNT can be left undefined. + * TMRMS represents the desired mecs per tick (msecs per interrupt). + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_HZ 1000 /* Always 1000 */ +#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ +#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */ +#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period */ +#define CONFIG_SYS_NIOS_TMRCNT \ + (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) + +/*------------------------------------------------------------------------ + * STATUS LED -- Provides a simple blinking led. For Nios2 each board + * must implement its own led routines -- leds are, after all, + * board-specific, no? + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ +#define CONFIG_STATUS_LED /* Enable status driver */ + +#define STATUS_LED_BIT 1 /* Bit-0 on PIO */ +#define STATUS_LED_STATE 1 /* Blinking */ +#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */ + +/*------------------------------------------------------------------------ + * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... + * and really doesn't need any additional clutter. So I choose the lazy + * way out to avoid changes there -- define the base address to ensure + * cache bypass so there's no need to monkey with inx/outx macros. + *----------------------------------------------------------------------*/ +#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ +#define CONFIG_NET_MULTI +#define CONFIG_SMC91111 /* Using SMC91c111 */ +#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ +#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ + +#define CONFIG_ETHADDR 08:00:3e:26:0a:5b +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 192.168.2.21 +#define CONFIG_SERVERIP 192.168.2.16 + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ + +#define CONFIG_CMD_BDI +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_SAVEENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_IMI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_LOADS +#define CONFIG_CMD_LOADB +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_RUN +#define CONFIG_CMD_SAVES + + +/*------------------------------------------------------------------------ + * COMPACT FLASH + *----------------------------------------------------------------------*/ +#if defined(CONFIG_CMD_IDE) +#define CONFIG_IDE_PREINIT /* Implement id_preinit */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* 1 drive per IDE bus */ + +#define CONFIG_SYS_ATA_BASE_ADDR 0x00900800 /* ATA base addr */ +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 /* IDE0 offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0040 /* Data IO offset */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0040 /* Register offset */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 /* Alternate reg offset */ +#define CONFIG_SYS_ATA_STRIDE 4 /* Width betwix addrs */ +#define CONFIG_DOS_PARTITION + +/* Board-specific cf regs */ +#define CONFIG_SYS_CF_PRESENT 0x00900880 /* CF Present PIO base */ +#define CONFIG_SYS_CF_POWER 0x00900890 /* CF Power FET PIO base*/ +#define CONFIG_SYS_CF_ATASEL 0x009008a0 /* CF ATASEL PIO base */ + +#endif + +/*------------------------------------------------------------------------ + * JFFS2 + *----------------------------------------------------------------------*/ +#if defined(CONFIG_CMD_JFFS2) +#define CONFIG_SYS_JFFS_CUSTOM_PART /* board defined part */ +#endif + +/*------------------------------------------------------------------------ + * MISC + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_LONGHELP /* Provide extended help*/ +#define CONFIG_SYS_PROMPT "==> " /* Command prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */ +#define CONFIG_SYS_MAXARGS 16 /* Max command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */ +#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */ +#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000 + +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#endif /* __CONFIG_H */ |