diff options
Diffstat (limited to 'u-boot/include/configs/SBC8540.h')
| -rw-r--r-- | u-boot/include/configs/SBC8540.h | 446 |
1 files changed, 446 insertions, 0 deletions
diff --git a/u-boot/include/configs/SBC8540.h b/u-boot/include/configs/SBC8540.h new file mode 100644 index 0000000..72559c0 --- /dev/null +++ b/u-boot/include/configs/SBC8540.h @@ -0,0 +1,446 @@ +/* + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao <X.Xiao@motorola.com> + * + * (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>. + * Added support for Wind River SBC8540 board + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * sbc8540 board configuration file. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Top level Makefile configuration choices + */ +#ifdef CONFIG_66 +#define CONFIG_PCI_66 +#endif + +#define TSEC_DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ +#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ + +#define CONFIG_SYS_TEXT_BASE 0xfffc0000 + + +#define CONFIG_CPM2 1 /* has CPM2 */ + +#define CONFIG_SBC8540 1 /* configuration for SBC8560 board */ +#define CONFIG_MPC8540 1 + +#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific (supplement) */ + +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#undef CONFIG_PCI /* pci ethernet support */ +#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ + +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +/* Using Localbus SDRAM to emulate flash before we can program the flash, + * normally you need a flash-boot image(u-boot.bin), if so undef this. + */ +#undef CONFIG_RAM_AS_FLASH + +#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */ + #define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */ +#else + #define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */ +#endif + +/* below can be toggled for performance analysis. otherwise use default */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#undef CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 + +#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \ + defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \ + defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC)) +#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." +#endif + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ + +#if XXX + #define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ +#else + #define CONFIG_SYS_CCSRBAR 0xff700000 /* default CCSRBAR */ +#endif +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ + +#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ + +/* DDR Setup */ +#define CONFIG_FSL_DDR1 +#undef CONFIG_FSL_DDR_INTERACTIVE +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_SPD + +#if defined(CONFIG_MPC85xx_REV1) +#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ +#endif + +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS 0x55 /* CTLR 0 DIMM 0 */ + +#undef CONFIG_CLOCKS_IN_MHZ + +#if defined(CONFIG_RAM_AS_FLASH) + #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ + #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 8M */ + #define CONFIG_SYS_BR0_PRELIM 0xf8000801 /* port size 8bit */ + #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */ +#else /* Boot from real Flash */ + #define CONFIG_SYS_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ + #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ + #define CONFIG_SYS_BR0_PRELIM 0xff800801 /* port size 8bit */ + #define CONFIG_SYS_OR0_PRELIM 0xff800ff7 /* 8MB Flash */ +#endif +#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +/* local bus definitions */ +#define CONFIG_SYS_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */ +#define CONFIG_SYS_OR1_PRELIM 0xfc000ff7 + +#define CONFIG_SYS_BR2_PRELIM 0x00000000 /* CS2 not used */ +#define CONFIG_SYS_OR2_PRELIM 0x00000000 + +#define CONFIG_SYS_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */ +#define CONFIG_SYS_OR3_PRELIM 0xfc000cc1 + +#if defined(CONFIG_RAM_AS_FLASH) + #define CONFIG_SYS_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */ +#else + #define CONFIG_SYS_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */ +#endif +#define CONFIG_SYS_OR4_PRELIM 0xfc000cc1 + +#define CONFIG_SYS_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */ +#if 1 + #define CONFIG_SYS_OR5_PRELIM 0xff000ff7 +#else + #define CONFIG_SYS_OR5_PRELIM 0xff0000f0 +#endif + +#define CONFIG_SYS_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */ +#define CONFIG_SYS_OR6_PRELIM 0xfc000ff7 +#define CONFIG_SYS_LBC_LCRR 0x00030002 /* local bus freq */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LBC_LSRT 0x20000000 +#define CONFIG_SYS_LBC_MRTPR 0x20000000 +#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 +#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 +#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 + +/* just hijack the MOT BCSR def for SBC8560 misc devices */ +#define CONFIG_SYS_BCSR ((CONFIG_SYS_BR5_PRELIM & 0xff000000)|0x00400000) +/* the size of CS5 needs to be >= 16M for TLB and LAW setups */ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#if 0 +#define CONFIG_SYS_NS16550_CLK 1843200 /* get_bus_freq(0) */ +#else +#define CONFIG_SYS_NS16550_CLK 264000000 /* get_bus_freq(0) */ +#endif + +#define CONFIG_BAUDRATE 9600 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#if 0 +#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00700000) +#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00800000) +#else +/* SBC8540 uses internal COMM controller */ +#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_CCSRBAR & 0xfff00000)+0x00004500) +#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_CCSRBAR & 0xfff00000)+0x00004600) +#endif + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 + +#define CONFIG_SYS_PCI_MEM_BASE 0xC0000000 +#define CONFIG_SYS_PCI_MEM_PHYS 0xC0000000 +#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 + +#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ + +# define CONFIG_NET_MULTI 1 +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define CONFIG_MII 1 /* MII PHY management */ +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" + + +#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ + + #undef CONFIG_ETHER_NONE /* define if ether on something else */ + #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */ + #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ + + #if (CONFIG_ETHER_INDEX == 2) + /* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers + * - Full duplex + */ + #define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) + #define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) + #define CONFIG_SYS_CPMFCR_RAMTYPE 0 + #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) + + #elif (CONFIG_ETHER_INDEX == 3) + /* need more definitions here for FE3 */ + #endif /* CONFIG_ETHER_INDEX */ + + #define CONFIG_MII /* MII PHY management */ + #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ + /* + * GPIO pins used for bit-banged MII communications + */ + #define MDIO_PORT 2 /* Port C */ + #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ + (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) + #define MDC_DECLARE MDIO_DECLARE + + #define MDIO_ACTIVE (iop->pdir |= 0x00400000) + #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) + #define MDIO_READ ((iop->pdat & 0x00400000) != 0) + + #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ + else iop->pdat &= ~0x00400000 + + #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ + else iop->pdat &= ~0x00200000 + + #define MIIDELAY udelay(1) + +#endif + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#if 0 +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */ +#endif +#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if 0 +/* XXX This doesn't work and I don't want to fix it */ +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) + #define CONFIG_SYS_RAMBOOT +#else + #undef CONFIG_SYS_RAMBOOT +#endif +#endif + +/* Environment */ +#if !defined(CONFIG_SYS_RAMBOOT) + #if defined(CONFIG_RAM_AS_FLASH) + #define CONFIG_ENV_IS_NOWHERE + #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000) + #define CONFIG_ENV_SIZE 0x2000 + #else + #define CONFIG_ENV_IS_IN_FLASH 1 + #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) + #define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */ + #endif +#else + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600" +/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/ +#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000" +#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_REGINFO + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + +#if defined(CONFIG_SYS_RAMBOOT) + #undef CONFIG_CMD_SAVEENV + #undef CONFIG_CMD_LOADS +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "SBC8540=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#if defined(CONFIG_CMD_KGDB) + #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ + #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/*Note: change below for your network setting!!! */ +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +# define CONFIG_ETHADDR 00:vv:ww:xx:yy:8a +# define CONFIG_HAS_ETH1 +# define CONFIG_ETH1ADDR 00:vv:ww:xx:yy:8b +# define CONFIG_HAS_ETH2 +# define CONFIG_ETH2ADDR 00:vv:ww:xx:yy:8c +#endif + +#define CONFIG_SERVERIP YourServerIP +#define CONFIG_IPADDR YourTargetIP +#define CONFIG_GATEWAYIP YourGatewayIP +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_HOSTNAME SBC8560 +#define CONFIG_ROOTPATH YourRootPath +#define CONFIG_BOOTFILE YourImageName + +#endif /* __CONFIG_H */ |