diff options
Diffstat (limited to 'u-boot/include/configs/bf533-stamp.h')
| -rw-r--r-- | u-boot/include/configs/bf533-stamp.h | 209 |
1 files changed, 209 insertions, 0 deletions
diff --git a/u-boot/include/configs/bf533-stamp.h b/u-boot/include/configs/bf533-stamp.h new file mode 100644 index 0000000..bf0f063 --- /dev/null +++ b/u-boot/include/configs/bf533-stamp.h @@ -0,0 +1,209 @@ +/* + * U-boot - Configuration file for BF533 STAMP board + */ + +#ifndef __CONFIG_BF533_STAMP_H__ +#define __CONFIG_BF533_STAMP_H__ + +#include <asm/config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 11059200 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 45 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 6 /* note: 1.2 boards can go faster */ + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 11 +#define CONFIG_MEM_SIZE 128 + +#define CONFIG_EBIU_SDRRC_VAL 0x268 +#define CONFIG_EBIU_SDGCTL_VAL 0x911109 + +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) + + +/* + * Network Settings + */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_NET_MULTI +#define CONFIG_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20300300 +#define SMC91111_EEPROM_INIT() \ + do { \ + bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \ + bfin_write_FIO_FLAG_C(PF1); \ + bfin_write_FIO_FLAG_S(PF0); \ + SSYNC(); \ + } while (0) +#define CONFIG_HOSTNAME bf533-stamp +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ + + +/* + * Flash Settings + */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 67 + + +/* + * SPI Settings + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ALL + + +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#endif +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED +#else +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#endif +#ifdef ENV_IS_EMBEDDED +/* WARNING - the following is hand-optimized to fit within + * the sector before the environment sector. If it throws + * an error during compilation remove an object here to get + * it linked after the configuration sector. + */ +# define LDS_BOARD_TEXT \ + arch/blackfin/lib/libblackfin.o (.text*); \ + arch/blackfin/cpu/libblackfin.o (.text*); \ + . = DEFINED(env_offset) ? env_offset : .; \ + common/env_embedded.o (.text*); +#endif + + +/* + * I2C Settings + */ +#define CONFIG_SOFT_I2C +#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3 +#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2 + + +/* + * Compact Flash / IDE / ATA Settings + */ + +/* Enabled below option for CF support */ +/* #define CONFIG_STAMP_CF */ +#if defined(CONFIG_STAMP_CF) +#define CONFIG_MISC_INIT_R +#define CONFIG_DOS_PARTITION 1 +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_RESET /* no reset for ide supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) + +#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */ + +#define CONFIG_SYS_ATA_STRIDE 2 + +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 +#endif + + +/* + * Misc Settings + */ +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 + +/* FLASH/ETHERNET uses the same async bank */ +#define SHARED_RESOURCES 1 + +/* define to enable boot progress via leds */ +/* #define CONFIG_SHOW_BOOT_PROGRESS */ + +/* define to enable run status via led */ +/* #define CONFIG_STATUS_LED */ +#ifdef CONFIG_STATUS_LED +#define CONFIG_GPIO_LED +#define CONFIG_BOARD_SPECIFIC_LED +/* use LED0 to indicate booting/alive */ +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT GPIO_PF2 +#define STATUS_LED_STATE STATUS_LED_ON +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) +/* use LED1 to indicate crash */ +#define STATUS_LED_CRASH 1 +#define STATUS_LED_BIT1 GPIO_PF3 +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) +/* #define STATUS_LED_BIT2 GPIO_PF4 */ +#endif + +/* define to enable splash screen support */ +/* #define CONFIG_VIDEO */ + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +#endif |