1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
|
/*
* (C) Copyright 2005
* Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <command.h>
#include <malloc.h>
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f (void)
{
unsigned long CPC0_CR0Reg;
/*
* Setup GPIO pins
*/
CPC0_CR0Reg = mfdcr(CPC0_CR0);
mtdcr(CPC0_CR0, CPC0_CR0Reg |
((CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED |
CONFIG_SYS_SELF_RST | CONFIG_SYS_INTA_FAKE) << 5));
/* set output pins to high */
out_be32((void *)GPIO0_OR, CONFIG_SYS_EEPROM_WP);
/* setup for output (LED=off) */
out_be32((void *)GPIO0_TCR, CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED);
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
* IRQ 16 405GP internally generated; active low; level sensitive
* IRQ 17-24 RESERVED
* IRQ 25 (EXT IRQ 0) PB0; active low; level sensitive
* IRQ 26 (EXT IRQ 1) PB1; active low; level sensitive
* IRQ 27 (EXT IRQ 2) PCI SLOT 0; active low; level sensitive
* IRQ 28 (EXT IRQ 3) PCI SLOT 1; active low; level sensitive
* IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
* IRQ 30 (EXT IRQ 5) PCI SLOT 3; active low; level sensitive
* IRQ 31 (EXT IRQ 6) unused
*/
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
mtdcr(UIC0ER, 0x00000000); /* disable all ints */
mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
mtdcr(UIC0PR, 0xFFFFFF81); /* set int polarities */
mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
return 0;
}
int misc_init_r (void)
{
unsigned long CPC0_CR0Reg;
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
/*
* Select cts (and not dsr) on uart1
*/
CPC0_CR0Reg = mfdcr(CPC0_CR0);
mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
return (0);
}
/*
* Check Board Identity:
*/
int checkboard (void)
{
char str[64];
int i = getenv_f("serial#", str, sizeof(str));
puts ("Board: ");
if (i == -1) {
puts ("### No HW ID - assuming CPCI2DP");
} else {
puts(str);
}
printf(" (Ver 1.0)");
putc ('\n');
return 0;
}
#if defined(CONFIG_SYS_EEPROM_WREN)
/* Input: <dev_addr> I2C address of EEPROM device to enable.
* <state> -1: deliver current state
* 0: disable write
* 1: enable write
* Returns: -1: wrong device address
* 0: dis-/en- able done
* 0/1: current state if <state> was -1.
*/
int eeprom_write_enable (unsigned dev_addr, int state) {
if (CONFIG_SYS_I2C_EEPROM_ADDR != dev_addr) {
return -1;
} else {
switch (state) {
case 1:
/* Enable write access, clear bit GPIO_SINT2. */
out_be32((void *)GPIO0_OR,
in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP);
state = 0;
break;
case 0:
/* Disable write access, set bit GPIO_SINT2. */
out_be32((void *)GPIO0_OR,
in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
state = 0;
break;
default:
/* Read current status back. */
state = (0 == (in_be32((void *)GPIO0_OR) &
CONFIG_SYS_EEPROM_WP));
break;
}
}
return state;
}
#endif
#if defined(CONFIG_SYS_EEPROM_WREN)
int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int query = argc == 1;
int state = 0;
if (query) {
/* Query write access state. */
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, -1);
if (state < 0) {
puts ("Query of write access state failed.\n");
} else {
printf ("Write access for device 0x%0x is %sabled.\n",
CONFIG_SYS_I2C_EEPROM_ADDR, state ? "en" : "dis");
state = 0;
}
} else {
if ('0' == argv[1][0]) {
/* Disable write access. */
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 0);
} else {
/* Enable write access. */
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 1);
}
if (state < 0) {
puts ("Setup of write access state failed.\n");
}
}
return state;
}
U_BOOT_CMD(
eepwren, 2, 0, do_eep_wren,
"Enable / disable / query EEPROM write access",
""
);
#endif /* #if defined(CONFIG_SYS_EEPROM_WREN) */
|
