1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
/* u-boot driver for the OrtusTech COM37H3M05DTC LCM
*
* Copyright (C) 2006-2007 by OpenMoko, Inc.
* Author: Harald Welte <laforge@openmoko.org>
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
*/
#include <common.h>
#include <asm/errno.h>
#include <asm/io.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/gpio.h>
#include <asm/mach-types.h>
#include <twl4030.h>
#include "../gta04/dssfb.h"
#include "../gta04/jbt6k74.h" // FIXME: change to display.h and make it more generic
#include "COM37H3M05DTC.h"
#ifdef CONFIG_OMAP3_BEAGLE_EXPANDER
#define GPIO_STBY 158
#endif
// configure beagle board DSS for the COM37H3M05DTC
#define DVI_BACKGROUND_COLOR 0x00fadc29 // rgb(250, 220, 41)
#define DSS1_FCLK 432000000 // see figure 15-65
#define PIXEL_CLOCK 22400000 // approx. 22.4 MHz (will be divided from 432 MHz)
// all values are min ratings
#define VDISP 640 // vertical active area
#define VFP 2 // vertical front porch
#define VS 1 // VSYNC pulse width (negative going)
#define VBP 3 // vertical back porch
#define VDS (VS+VBP) // vertical data start
#define VBL (VS+VBP+VFP) // vertical blanking period
#define VP (VDISP+VBL) // vertical cycle
#define HDISP 480 // horizontal active area
#define HFP 2 // horizontal front porch
#define HS 2 // HSYNC pulse width (negative going)
#define HBP 9 // horizontal back porch
#define HDS (HS+HBP) // horizontal data start
#define HBL (HS+HBP+HFP) // horizontal blanking period
#define HP (HDISP+HBL) // horizontal cycle
static const struct panel_config lcm_cfg =
{
.timing_h = ((HBP-1)<<20) | ((HFP-1)<<8) | ((HS-1)<<0), /* Horizantal timing */
.timing_v = ((VBP+0)<<20) | ((VFP+0)<<8) | ((VS-1)<<0), /* Vertical timing */
// negative clock edge
// negative sync pulse
// positive DE pulse
.pol_freq = (1<<17)|(1<<16)|(0<<15)|(0<<14)|(1<<13)|(1<<12)|0x28, /* Pol Freq */
.divisor = (0x0001<<16)|(DSS1_FCLK/PIXEL_CLOCK), /* Pixel Clock divisor from dss1_fclk */
.lcd_size = ((HDISP-1)<<0) | ((VDISP-1)<<16), /* as defined by LCM */
.panel_type = 0x01, /* TFT */
.data_lines = 0x03, /* 24 Bit RGB */
.load_mode = 0x02, /* Frame Mode */
.panel_color = DVI_BACKGROUND_COLOR
};
int jbt_reg_init(void)
{
omap_request_gpio(GPIO_STBY);
omap_set_gpio_direction(GPIO_STBY, 0); // output
return 0;
}
int jbt_check(void)
{
return 0;
}
const char *jbt_state(void)
{
return "?";
}
/* frontend function */
int jbt6k74_enter_state(enum jbt_state new_state)
{
return 0;
}
int jbt6k74_display_onoff(int on)
{
omap_set_gpio_dataout(GPIO_STBY, on?0:1); // on = no STBY
return 0;
}
int board_video_init(GraphicDevice *pGD)
{
extern int get_board_revision(void);
// FIXME: here we should pass down the GPIO(s)
backlight_init(); // initialize backlight
#define REVISION_XM 0
if(get_board_revision() == REVISION_XM) {
/* Set VAUX1 to 3.3V for GTA04E display board */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX1_DEDICATED,
/*TWL4030_PM_RECEIVER_VAUX1_VSEL_33*/ 0x07,
TWL4030_PM_RECEIVER_VAUX1_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
udelay(5000);
}
// FIXME: here we should init the TSC and pass down the GPIO numbers and resistance values
if(jbt_reg_init()) // initialize SPI
{
printf("No LCM connected\n");
return 1;
}
dssfb_init(&lcm_cfg);
printf("did board_video_init()\n");
return 0;
}
|
