diff options
Diffstat (limited to 'include/asm/arch-omap3/omap3430.h')
| -rw-r--r-- | include/asm/arch-omap3/omap3430.h | 197 |
1 files changed, 197 insertions, 0 deletions
diff --git a/include/asm/arch-omap3/omap3430.h b/include/asm/arch-omap3/omap3430.h new file mode 100644 index 0000000..117d752 --- /dev/null +++ b/include/asm/arch-omap3/omap3430.h @@ -0,0 +1,197 @@ +/* + * (C) Copyright 2006 + * Texas Instruments, <www.ti.com> + * Richard Woodruff <r-woodruff2@ti.com> + * Syed Mohammed Khasim <x0khasim@ti.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _OMAP3430_SYS_H_ +#define _OMAP3430_SYS_H_ + +#include <asm/arch/sizes.h> + +/* + * 3430 specific Section + */ + +/* Stuff on L3 Interconnect */ +#define SMX_APE_BASE 0x68000000 + +/* L3 Firewall */ +#define A_REQINFOPERM0 (SMX_APE_BASE + 0x05048) +#define A_READPERM0 (SMX_APE_BASE + 0x05050) +#define A_WRITEPERM0 (SMX_APE_BASE + 0x05058) + +/* GPMC */ +#define OMAP34XX_GPMC_BASE (0x6E000000) + +/* SMS */ +#define OMAP34XX_SMS_BASE 0x6C000000 + +/* SDRC */ +#define OMAP34XX_SDRC_BASE 0x6D000000 + +/* + * L4 Peripherals - L4 Wakeup and L4 Core now + */ +#define OMAP34XX_CORE_L4_IO_BASE 0x48000000 + +#define OMAP34XX_WAKEUP_L4_IO_BASE 0x48300000 + +#define OMAP34XX_L4_PER 0x49000000 + +#define OMAP34XX_L4_IO_BASE OMAP34XX_CORE_L4_IO_BASE + +/* CONTROL */ +#define OMAP34XX_CTRL_BASE (OMAP34XX_L4_IO_BASE+0x2000) + +/* TAP information dont know for 3430*/ +#define OMAP34XX_TAP_BASE (0x49000000) /*giving some junk for virtio */ + +/* UART */ +#define OMAP34XX_UART1 (OMAP34XX_L4_IO_BASE+0x6a000) +#define OMAP34XX_UART2 (OMAP34XX_L4_IO_BASE+0x6c000) +#define OMAP34XX_UART3 (OMAP34XX_L4_PER+0x20000) + +/* General Purpose Timers */ +#define OMAP34XX_GPT1 0x48318000 +#define OMAP34XX_GPT2 0x49032000 +#define OMAP34XX_GPT3 0x49034000 +#define OMAP34XX_GPT4 0x49036000 +#define OMAP34XX_GPT5 0x49038000 +#define OMAP34XX_GPT6 0x4903A000 +#define OMAP34XX_GPT7 0x4903C000 +#define OMAP34XX_GPT8 0x4903E000 +#define OMAP34XX_GPT9 0x49040000 +#define OMAP34XX_GPT10 0x48086000 +#define OMAP34XX_GPT11 0x48088000 +#define OMAP34XX_GPT12 0x48304000 + +/* WatchDog Timers (1 secure, 3 GP) */ +#define WD1_BASE (0x4830C000) +#define WD2_BASE (0x48314000) +#define WD3_BASE (0x49030000) + +/* 32KTIMER */ +#define SYNC_32KTIMER_BASE (0x48320000) +#define S32K_CR (SYNC_32KTIMER_BASE+0x10) + +/* omap3 GPIO registers */ +#define OMAP34XX_GPIO1_BASE 0x48310000 +#define OMAP34XX_GPIO2_BASE 0x49050000 +#define OMAP34XX_GPIO3_BASE 0x49052000 +#define OMAP34XX_GPIO4_BASE 0x49054000 +#define OMAP34XX_GPIO5_BASE 0x49056000 +#define OMAP34XX_GPIO6_BASE 0x49058000 + +/* + * SDP3430 specific Section + */ + +/* + * The 343x's chip selects are programmable. The mask ROM + * does configure CS0 to 0x08000000 before dispatch. So, if + * you want your code to live below that address, you have to + * be prepared to jump though hoops, to reset the base address. + * Same as in SDP3430 + */ +#ifdef CONFIG_OMAP34XX +/* base address for indirect vectors (internal boot mode) */ +#define SRAM_OFFSET0 0x40000000 +#define SRAM_OFFSET1 0x00200000 +#define SRAM_OFFSET2 0x0000F800 +#define SRAM_VECT_CODE (SRAM_OFFSET0|SRAM_OFFSET1|SRAM_OFFSET2) + +#define LOW_LEVEL_SRAM_STACK 0x4020FFFC +#endif + +#if defined(CONFIG_3430SDP) || defined(CONFIG_OMAP3EVM) +/* FPGA on Debug board.*/ +#define ETH_CONTROL_REG (DEBUG_BASE+0x30b) +#define LAN_RESET_REGISTER (DEBUG_BASE+0x1c) + +#define DIP_SWITCH_INPUT_REG2 (DEBUG_BASE+0x60) +#define LED_REGISTER (DEBUG_BASE+0x40) +#define FPGA_REV_REGISTER (DEBUG_BASE+0x10) +#define EEPROM_MAIN_BRD (DEBUG_BASE+0x10000+0x1800) +#define EEPROM_CONN_BRD (DEBUG_BASE+0x10000+0x1900) +#define EEPROM_UI_BRD (DEBUG_BASE+0x10000+0x1A00) +#define EEPROM_MCAM_BRD (DEBUG_BASE+0x10000+0x1B00) +#define ENHANCED_UI_EE_NAME "750-2075" +#endif + +/* + * 343x real hardware: + * ES1 = rev 0 + * + * ES2 onwards, the value maps to contents of IDCODE register [31:28]. + * + * Note : CPU_3XX_ES20 is used in cache.S. Please review before changing. + */ +#define CPU_3XX_ES10 0 +#define CPU_3XX_ES20 1 +#define CPU_3XX_ES21 2 +#define CPU_3XX_ES30 3 +#define CPU_3XX_ES31 4 +#define CPU_3XX_ES312 7 +#define CPU_3XX_MAX_REV 8 + +#define CPU_3XX_ID_SHIFT 28 + +#define WIDTH_8BIT 0x0000 +#define WIDTH_16BIT 0x1000 /* bit pos for 16 bit in gpmc */ + +/* + * Control idcode register contains hawkeye and revision info + */ +#define CONTROL_IDCODE 0x4830A204 +#define CONTROL_OMAP_STATUS 0x4800244C + +/* + * Hawkeye values + */ +#define HAWKEYE_OMAP34XX 0xb7ae +#define HAWKEYE_AM35XX 0xb868 +#define HAWKEYE_OMAP36XX 0xb891 + +#define HAWKEYE_SHIFT 12 + +/* + * Define CPU families + */ +#define CPU_OMAP34XX 0x3400 /* OMAP34xx/OMAP35 devices */ +#define CPU_AM35XX 0x3500 /* AM35xx devices */ +#define CPU_OMAP36XX 0x3600 /* OMAP36xx devices */ + +/* + * Control status register values corresponding to cpu variants + */ +#define OMAP3503 0x5c00 +#define OMAP3515 0x1c00 +#define OMAP3525 0x4c00 +#define OMAP3530 0x0c00 + +#define AM3505 0x5c00 +#define AM3517 0x1c00 + +#define OMAP3730 0x0c00 + +#endif /* _OMAP3430_SYS_H_ */ |