summaryrefslogtreecommitdiffstats
path: root/nfc/nfc_hw.c
blob: cd26be5df9fef0f557298efa567962d465cfc33a (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
/*
 * Copyright (C) 2011 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
#include <errno.h>
#include <string.h>

#include <hardware/hardware.h>
#include <hardware/nfc.h>

static uint8_t pn544_eedata_settings[][4] = {
    // DIFFERENTIAL_ANTENNA

    // RF Settings
    {0x00,0x9B,0xD1,0x0D} // Tx consumption higher than 0x0D (average 50mA)
    ,{0x00,0x9B,0xD2,0x24} // GSP setting for this threshold
    ,{0x00,0x9B,0xD3,0x0A} // Tx consumption higher than 0x0A (average 40mA)
    ,{0x00,0x9B,0xD4,0x22} // GSP setting for this threshold
    ,{0x00,0x9B,0xD5,0x08} // Tx consumption higher than 0x08 (average 30mA)
    ,{0x00,0x9B,0xD6,0x1E} // GSP setting for this threshold
    ,{0x00,0x9B,0xDD,0x1C} // GSP setting for this threshold
    ,{0x00,0x9B,0x84,0x13} // ANACM2 setting
#ifdef maguro
    // Maguro load modulation settings
    ,{0x00,0x99,0x29,0xF4} // Type A load modulation amplitude fine tuning
    ,{0x00,0x99,0x2A,0xF4} // Type B load modulation amplitude fine tuning
    ,{0x00,0x99,0x2B,0xF4} // Type B' load modulation amplitude fine tuning
    ,{0x00,0x99,0x85,0xF1} // Type Felica load modulation amplitude fine tuning
#endif
#ifdef toro
    // Toro load modulation settings
    ,{0x00,0x99,0x29,0xF3} // Type A load modulation amplitude fine tuning
    ,{0x00,0x99,0x2A,0xF3} // Type B load modulation amplitude fine tuning
    ,{0x00,0x99,0x2B,0xF3} // Type B' load modulation amplitude fine tuning
    ,{0x00,0x99,0x85,0xF1} // Type Felica load modulation amplitude fine tuning
#endif
    // For tuna we don't override load modulation settings.

    // Enable PBTF
    ,{0x00,0x98,0x00,0x3F} // SECURE_ELEMENT_CONFIGURATION - No Secure Element
    ,{0x00,0x9F,0x09,0x00} // SWP_PBTF_RFU
    ,{0x00,0x9F,0x0A,0x05} // SWP_PBTF_RFLD  --> RFLEVEL Detector for PBTF
    ,{0x00,0x9E,0xD1,0xA1} //

    // Change RF Level Detector ANARFLDWU
    ,{0x00,0x99,0x23,0x00} // Default Value is 0x01

    // Low-power polling
    ,{0x00,0x9E,0x74,0xB0} // Default Value is 0x00, bits 0->2: sensitivity (0==max, 6==min),
                           // bit 3: RFU,
                           // bits 4,5 hybrid low-power: # of low-power polls per regular poll
                           // bit 6: RFU
                           // bit 7: (0 -> disabled, 1 -> enabled)
    ,{0x00,0x9E,0x7D,0xB0} // bits 0->3: RFU,
                           // bits 4,5: # retries after low power detection
                           // 0=1 retry, 1=2 retry, 2=3 retry, 3=4 retry
                           // bit 6: RFU,
                           // bit 7: Enable or disable retry mechanism (0: disable, 1: enable)
    ,{0x00,0x9F,0x28,0x01} // bits 0->7: # of measurements per low-power poll

    // Polling Loop - Card Emulation Timeout
    ,{0x00,0x9F,0x35,0x14} // Time for which PN544 stays in Card Emulation mode after leaving RF field
    ,{0x00,0x9F,0x36,0x60} // Default value 0x0411 = 50 ms ---> New Value : 0x1460 = 250 ms

    //LLC Timer
    ,{0x00,0x9C,0x31,0x00} // Guard host time-out in ms (MSB)
    ,{0x00,0x9C,0x32,0xC8} // Guard host time-out in ms (LSB)
    ,{0x00,0x9C,0x19,0x40} // Max RX retry (PN544=>host?)
    ,{0x00,0x9C,0x1A,0x40} // Max TX retry (PN544=>host?)

    ,{0x00,0x9C,0x0C,0x00} //
    ,{0x00,0x9C,0x0D,0x00} //
    ,{0x00,0x9C,0x12,0x00} //
    ,{0x00,0x9C,0x13,0x00} //

    // NFC-DEP Target Waiting Time (WT)
    ,{0x00,0x98,0xA2,0x08} // Set to 0x08 as required by [digital] (default value: 09)

    //SE GPIO
    ,{0x00, 0x98, 0x93, 0x40}

    // Set NFCT ATQA
    ,{0x00, 0x98, 0x7D, 0x02}
    ,{0x00, 0x98, 0x7E, 0x00}

    // Enable CEA detection mechanism
    ,{0x00, 0x9F, 0xC8, 0x01}
    // Set NFC-F poll RC=0x00
    ,{0x00, 0x9F, 0x9A, 0x00}
    // Setting for EMD support for ISO 14443-4 Reader
    ,{0x00,0x9F,0x09,0x00} // 0x00 - Disable EMD support, 0x01 - Enable EMD support
};

static int pn544_close(hw_device_t *dev) {
    free(dev);

    return 0;
}

/*
 * Generic device handling
 */

static int nfc_open(const hw_module_t* module, const char* name,
        hw_device_t** device) {
    if (strcmp(name, NFC_PN544_CONTROLLER) == 0) {
        nfc_pn544_device_t *dev = calloc(1, sizeof(nfc_pn544_device_t));

        dev->common.tag = HARDWARE_DEVICE_TAG;
        dev->common.version = 0;
        dev->common.module = (struct hw_module_t*) module;
        dev->common.close = pn544_close;

        dev->num_eeprom_settings = sizeof(pn544_eedata_settings) / 4;
        dev->eeprom_settings = (uint8_t*)pn544_eedata_settings;
        dev->linktype = PN544_LINK_TYPE_UART;
        dev->device_node = "/dev/ttyO3";
        dev->enable_i2c_workaround = 0;
        *device = (hw_device_t*) dev;
        return 0;
    } else {
        return -EINVAL;
    }
}

static struct hw_module_methods_t nfc_module_methods = {
    .open = nfc_open,
};

struct nfc_module_t HAL_MODULE_INFO_SYM = {
    .common = {
        .tag = HARDWARE_MODULE_TAG,
        .version_major = 1,
        .version_minor = 0,
        .id = NFC_HARDWARE_MODULE_ID,
        .name = "Tuna NFC HW HAL",
        .author = "The Android Open Source Project",
        .methods = &nfc_module_methods,
    },
};