diff options
Diffstat (limited to 'hci/include/bt_vendor_lib.h')
-rw-r--r-- | hci/include/bt_vendor_lib.h | 323 |
1 files changed, 323 insertions, 0 deletions
diff --git a/hci/include/bt_vendor_lib.h b/hci/include/bt_vendor_lib.h new file mode 100644 index 0000000..054e317 --- /dev/null +++ b/hci/include/bt_vendor_lib.h @@ -0,0 +1,323 @@ +/****************************************************************************** + * + * Copyright (C) 2009-2012 Broadcom Corporation + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ******************************************************************************/ + +#ifndef BT_VENDOR_LIB_H +#define BT_VENDOR_LIB_H + +#include <stdint.h> +#include <sys/cdefs.h> +#include <sys/types.h> + +/** Struct types */ + + +/** Typedefs and defines */ + +/** Vendor specific operations OPCODE */ +typedef enum { +/* [operation] + * Power on or off the BT Controller. + * [input param] + * A pointer to int type with content of bt_vendor_power_state_t. + * Typecasting conversion: (int *) param. + * [return] + * 0 - default, don't care. + * [callback] + * None. + */ + BT_VND_OP_POWER_CTRL, + +/* [operation] + * Perform any vendor specific initialization or configuration + * on the BT Controller. This is called before stack initialization. + * [input param] + * None. + * [return] + * 0 - default, don't care. + * [callback] + * Must call fwcfg_cb to notify the stack of the completion of vendor + * specific initialization once it has been done. + */ + BT_VND_OP_FW_CFG, + +/* [operation] + * Perform any vendor specific SCO/PCM configuration on the BT Controller. + * This is called after stack initialization. + * [input param] + * None. + * [return] + * 0 - default, don't care. + * [callback] + * Must call scocfg_cb to notify the stack of the completion of vendor + * specific SCO configuration once it has been done. + */ + BT_VND_OP_SCO_CFG, + +/* [operation] + * Open UART port on where the BT Controller is attached. + * This is called before stack initialization. + * [input param] + * A pointer to int array type for open file descriptors. + * The mapping of HCI channel to fd slot in the int array is given in + * bt_vendor_hci_channels_t. + * And, it requires the vendor lib to fill up the content before returning + * the call. + * Typecasting conversion: (int (*)[]) param. + * [return] + * Numbers of opened file descriptors. + * Valid number: + * 1 - CMD/EVT/ACL-In/ACL-Out via the same fd (e.g. UART) + * 2 - CMD/EVT on one fd, and ACL-In/ACL-Out on the other fd + * 4 - CMD, EVT, ACL-In, ACL-Out are on their individual fd + * [callback] + * None. + */ + BT_VND_OP_USERIAL_OPEN, + +/* [operation] + * Close the previously opened UART port. + * [input param] + * None. + * [return] + * 0 - default, don't care. + * [callback] + * None. + */ + BT_VND_OP_USERIAL_CLOSE, + +/* [operation] + * Get the LPM idle timeout in milliseconds. + * The stack uses this information to launch a timer delay before it + * attempts to de-assert LPM WAKE signal once downstream HCI packet + * has been delivered. + * [input param] + * A pointer to uint32_t type which is passed in by the stack. And, it + * requires the vendor lib to fill up the content before returning + * the call. + * Typecasting conversion: (uint32_t *) param. + * [return] + * 0 - default, don't care. + * [callback] + * None. + */ + BT_VND_OP_GET_LPM_IDLE_TIMEOUT, + +/* [operation] + * Enable or disable LPM mode on BT Controller. + * [input param] + * A pointer to uint8_t type with content of bt_vendor_lpm_mode_t. + * Typecasting conversion: (uint8_t *) param. + * [return] + * 0 - default, don't care. + * [callback] + * Must call lpm_cb to notify the stack of the completion of LPM + * disable/enable process once it has been done. + */ + BT_VND_OP_LPM_SET_MODE, + +/* [operation] + * Assert or Deassert LPM WAKE on BT Controller. + * [input param] + * A pointer to uint8_t type with content of bt_vendor_lpm_wake_state_t. + * Typecasting conversion: (uint8_t *) param. + * [return] + * 0 - default, don't care. + * [callback] + * None. + */ + BT_VND_OP_LPM_WAKE_SET_STATE, +} bt_vendor_opcode_t; + +/** Power on/off control states */ +typedef enum { + BT_VND_PWR_OFF, + BT_VND_PWR_ON, +} bt_vendor_power_state_t; + +/** Define HCI channel identifier in the file descriptors array + used in BT_VND_OP_USERIAL_OPEN operation. + */ +typedef enum { + CH_CMD, // HCI Command channel + CH_EVT, // HCI Event channel + CH_ACL_OUT, // HCI ACL downstream channel + CH_ACL_IN, // HCI ACL upstream channel + + CH_MAX // Total channels +} bt_vendor_hci_channels_t; + +/** LPM disable/enable request */ +typedef enum { + BT_VND_LPM_DISABLE, + BT_VND_LPM_ENABLE, +} bt_vendor_lpm_mode_t; + +/** LPM WAKE set state request */ +typedef enum { + BT_VND_LPM_WAKE_ASSERT, + BT_VND_LPM_WAKE_DEASSERT, +} bt_vendor_lpm_wake_state_t; + +/** Callback result values */ +typedef enum { + BT_VND_OP_RESULT_SUCCESS, + BT_VND_OP_RESULT_FAIL, +} bt_vendor_op_result_t; + +/* + * Bluetooth Host/Controller Vendor callback structure. + */ + +/* vendor initialization/configuration callback */ +typedef void (*cfg_result_cb)(bt_vendor_op_result_t result); + +/* datapath buffer allocation callback (callout) + * + * Vendor lib needs to request a buffer through the alloc callout function + * from HCI lib if the buffer is for constructing a HCI Command packet which + * will be sent through xmit_cb to BT Controller. + * + * For each buffer allocation, the requested size needs to be big enough to + * accommodate the below header plus a complete HCI packet -- + * typedef struct + * { + * uint16_t event; + * uint16_t len; + * uint16_t offset; + * uint16_t layer_specific; + * } HC_BT_HDR; + * + * HCI lib returns a pointer to the buffer where Vendor lib should use to + * construct a HCI command packet as below format: + * + * -------------------------------------------- + * | HC_BT_HDR | HCI command | + * -------------------------------------------- + * where + * HC_BT_HDR.event = 0x2000; + * HC_BT_HDR.len = Length of HCI command; + * HC_BT_HDR.offset = 0; + * HC_BT_HDR.layer_specific = 0; + * + * For example, a HCI_RESET Command will be formed as + * ------------------------ + * | HC_BT_HDR |03|0c|00| + * ------------------------ + * with + * HC_BT_HDR.event = 0x2000; + * HC_BT_HDR.len = 3; + * HC_BT_HDR.offset = 0; + * HC_BT_HDR.layer_specific = 0; + */ +typedef void* (*malloc_cb)(int size); + +/* datapath buffer deallocation callback (callout) */ +typedef void (*mdealloc_cb)(void *p_buf); + +/* define callback of the cmd_xmit_cb + * + * The callback function which HCI lib will call with the return of command + * complete packet. Vendor lib is responsible for releasing the buffer passed + * in at the p_mem parameter by calling dealloc callout function. + */ +typedef void (*tINT_CMD_CBACK)(void *p_mem); + +/* hci command packet transmit callback (callout) + * + * Vendor lib calls xmit_cb callout function in order to send a HCI Command + * packet to BT Controller. The buffer carrying HCI Command packet content + * needs to be first allocated through the alloc callout function. + * HCI lib will release the buffer for Vendor lib once it has delivered the + * packet content to BT Controller. + * + * Vendor lib needs also provide a callback function (p_cback) which HCI lib + * will call with the return of command complete packet. + * + * The opcode parameter gives the HCI OpCode (combination of OGF and OCF) of + * HCI Command packet. For example, opcode = 0x0c03 for the HCI_RESET command + * packet. + */ +typedef uint8_t (*cmd_xmit_cb)(uint16_t opcode, void *p_buf, tINT_CMD_CBACK p_cback); + +typedef struct { + /** set to sizeof(bt_vendor_callbacks_t) */ + size_t size; + + /* + * Callback and callout functions have implemented in HCI libray + * (libbt-hci.so). + */ + + /* notifies caller result of firmware configuration request */ + cfg_result_cb fwcfg_cb; + + /* notifies caller result of sco configuration request */ + cfg_result_cb scocfg_cb; + + /* notifies caller result of lpm enable/disable */ + cfg_result_cb lpm_cb; + + /* buffer allocation request */ + malloc_cb alloc; + + /* buffer deallocation request */ + mdealloc_cb dealloc; + + /* hci command packet transmit request */ + cmd_xmit_cb xmit_cb; +} bt_vendor_callbacks_t; + +/* + * Bluetooth Host/Controller VENDOR Interface + */ +typedef struct { + /** Set to sizeof(bt_vndor_interface_t) */ + size_t size; + + /* + * Functions need to be implemented in Vendor libray (libbt-vendor.so). + */ + + /** + * Caller will open the interface and pass in the callback routines + * to the implemenation of this interface. + */ + int (*init)(const bt_vendor_callbacks_t* p_cb, unsigned char *local_bdaddr); + + /** Vendor specific operations */ + int (*op)(bt_vendor_opcode_t opcode, void *param); + + /** Closes the interface */ + void (*cleanup)(void); +} bt_vendor_interface_t; + + +/* + * External shared lib functions/data + */ + +/* Entry point of DLib -- + * Vendor library needs to implement the body of bt_vendor_interface_t + * structure and uses the below name as the variable name. HCI library + * will use this symbol name to get address of the object through the + * dlsym call. + */ +extern const bt_vendor_interface_t BLUETOOTH_VENDOR_LIB_INTERFACE; + +#endif /* BT_VENDOR_LIB_H */ + |