diff options
Diffstat (limited to 'include/bte.h')
| -rw-r--r-- | include/bte.h | 119 |
1 files changed, 119 insertions, 0 deletions
diff --git a/include/bte.h b/include/bte.h new file mode 100644 index 0000000..103b660 --- /dev/null +++ b/include/bte.h @@ -0,0 +1,119 @@ +/****************************************************************************** + * + * Copyright (C) 2001-2012 Broadcom Corporation + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ******************************************************************************/ + +/****************************************************************************** + * + * this file contains constants and definitions for the bte project + * + ******************************************************************************/ +#ifndef BTE_H +#define BTE_H + +#include <semaphore.h> +#include <signal.h> +#include <pthread.h> +#include "bt_target.h" + +/* by default on shutdown, baudrate is reset 115kbits. this should NOT be need for platforms + * that kill BTE driver and remove/reset BT chip + */ +#ifndef BTE_RESET_BAUD_ON_BT_DISABLE +#define BTE_RESET_BAUD_ON_BT_DISABLE TRUE +#endif + +/* Target Modes (based on jumper settings on hardware [see user manual]) */ +enum +{ + /* BTE BBY */ + /* J3 J4 SW3-3 SW3-2 SW3-1 */ + /* -------------------------------------------- */ + BTE_MODE_SERIAL_APP, /* OUT OUT OFF OFF OFF Sample serial port application */ + BTE_MODE_APPL, /* IN OUT OFF OFF ON Target used with Tester through RPC */ + BTE_MODE_RESERVED, /* OUT IN OFF ON OFF Reserved */ + BTE_MODE_SAMPLE_APPS, /* IN IN OFF ON ON Sample applications (ICP/HSP) */ + BTE_MODE_DONGLE, /* not yet supported ON OFF OFF Dongle mode */ + BTE_MODE_APPL_PROTOCOL_TRACE, /* this is a fake mode do allow protocol tracing in application without rpc */ + BTE_MODE_INVALID +}; + +extern volatile UINT8 bte_target_mode; /* indicates the mode that the board is running in */ + +/* Startup options */ +extern UINT32 bte_startup_options; /* Switch and jumper settings at startup */ +void bte_get_startup_options(UINT32 *p_options); /* Platform specific function for getting startup options */ + +#define BTE_OPTIONS_TARGET_MODE_MASK 0x00000007 /* bits 2-0 indicate target mode (QuickConnect: jp3 & jp4, BBY: SW3-1 & SW3-2)*/ + + +/**************************************************************************** + * Definitions to define which type of application gets built + ****************************************************************************/ +#define BUILD_HCITOOL FALSE +#define BUILD_L2PING FALSE + + +#define LINUX_FM_DRIVER_INCLUDED FALSE + + +/* hcisu userial operations. should probably go into bt_types to avoid collisions! */ +#define BT_EVT_TO_HCISU_USERIAL_OP (0x0080 | BT_EVT_HCISU) +/* operation for above hcisu event */ +#define BT_HCISU_USERIAL_OPEN (0) /* open serial port calling USERIAL_Open() */ +#define BT_HCISU_USERIAL_CLOSE (1) /* close userial port */ +/* options associated with close op */ +#define BT_HCISU_USERIAL_CL_NO_DIS_BT 0 /* do not touch bt_wake and power gpio */ +#define BT_HCISU_USERIAL_CL_DIS_BT 1 /* put power and bt_wake into defined off state to preserve + power */ +/* status codes for callback */ +#define BTE_HCISU_USERIAL_FAIL 0 +#define BTE_HCISU_USERIAL_OK 1 +typedef void (tUSERIAL_MSG_CBACK) (int status); +typedef struct tHCISU_USERIAL_MSG_tag { + BT_HDR hdr; + tUSERIAL_MSG_CBACK *p_cback; + UINT8 port; /* port number */ + UINT8 op; + UINT8 option; /* option for operation. depends on operation */ +} tHCISU_USERIAL_MSG; + +extern void bte_hcisu_userial_oper( tUSERIAL_MSG_CBACK *p_cback, UINT8 port, UINT8 op, UINT8 option ); + +/* Pointer to function for sending HCI commands and data to the HCI tranport */ +extern int (*p_bte_hci_send)(UINT16 port, BT_HDR *p_msg); + + +/* Protocol trace mask */ +extern UINT32 bte_proto_trace_mask; + +/* Version string */ +extern const UINT8 bte_version_string[]; + +typedef struct tBAUD_REG_tag { + UINT8 DHBR; + UINT8 DLBR; + UINT8 ExplicitBaudRate0; + UINT8 ExplicitBaudRate1; + UINT8 ExplicitBaudRate2; + UINT8 ExplicitBaudRate3; +} tBAUD_REG; + +#include "gki.h" + +extern const tBAUD_REG baud_rate_regs[]; + +#endif /* BTE_H */ |