diff options
Diffstat (limited to 'inc/nfc_custom_config_example.h')
| -rw-r--r-- | inc/nfc_custom_config_example.h | 200 |
1 files changed, 200 insertions, 0 deletions
diff --git a/inc/nfc_custom_config_example.h b/inc/nfc_custom_config_example.h new file mode 100644 index 0000000..d400bcc --- /dev/null +++ b/inc/nfc_custom_config_example.h @@ -0,0 +1,200 @@ +/* + * Copyright (C) 2010 NXP Semiconductors + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + + +/** +* \file nfc_custom_config.h +* \brief HAL Custom Configurations +* +* +* \note This is the configuration header file of the HAL 4.0. custom configurable +* parameters of the HAL 4.0 are provided in this file +* +* Project: NFC-FRI-1.1 / HAL4.0 +* +* $Date: Fri Jun 11 16:44:31 2010 $ +* $Author: ing04880 $ +* $Revision: 1.11 $ +* $Aliases: NFC_FRI1.1_WK1023_R35_1 $ +* +*/ + + +/*@{*/ +#ifndef NFC_CUSTOM_CONFIG_H +#define NFC_CUSTOM_CONFIG_H +/*@}*/ + + +/** +* \name Hal +* +* File: \ref nfc_custom_config.h +* +*/ + + +/* + ***************************************************************** + ********************** CUSTOM MACROS ************************** + ***************************************************************** + */ + +/**< Max number of remote devices supported*/ +#define MAX_REMOTE_DEVICES 0x10 + + +/**< Default Session ID for Initialisation */ +#define DEFAULT_SESSION "NXP-NFC2" + +/** Resolution value for the timer, here the + timer resolution is 100 milliseconds */ +#define TIMER_RESOLUTION 100U + +/**< Defines connection time out value for LLC timer, + 500 is in milliseconds */ +#define LINK_CONNECTION_TIMEOUT 500U + +/**< Defines guard time out value for LLC timer, + 250 is in milliseconds */ +#define LINK_GUARD_TIMEOUT 250U + +/**< Macro to Enable SMX Feature During + * Initialisation */ + + +/* PLEASE NOTE: This Macro should be only enabled if there is a SMART_MX + * Chip attached to the PN544. + */ +/* #define NXP_HAL_ENABLE_SMX */ + + + +/* PLEASE NOTE: Kindly change the DEFAULT_SESSION Macro for each of the + * configuration change done for the below Macros + */ + +/**< External Clock Request Configuration for the NFC Device, + 0x00U -> No Clock Request, + 0x01U -> Clock Request through CLKREQ pin (GPIO pin 2), + 0x02U -> Clock Request through NXP_EVT_CLK_REQUEST Event, + */ +#define NXP_DEFAULT_CLK_REQUEST 0x00U + +/**< External Input Clock Setting for the NFC Device, + 0x00U -> No Input Clock Required (Use the Xtal), + 0x01U -> 13 MHZ, + 0x02U -> 19.2 MHZ, + 0x03U -> 26 MHZ, + 0x04U -> 38.4 MHZ, + 0x05U -> Custom (Set the Custome Clock Registry), + */ +#define NXP_DEFAULT_INPUT_CLK 0x00U + + + +#define NFC_DEV_HWCONF_DEFAULT 0xBCU + +/**< TX LDO Configuration + 0x00 -> 00b 3.0 V, + 0x01 -> 01b 3.0 V, + 0x02 -> 10b 2.7 V, + 0x03 -> 11b 3.3 V, + + */ +#define NXP_DEFAULT_TX_LDO 0x00U + + +/**< External Clock Request Configuration for the NFC Device, + 0x00U -> No Power Request, + 0x01U -> Power Request through CLKREQ pin (GPIO pin 2), + 0x02U -> Power Request through PWR_REQUEST (GPIO Pin 3), + */ +#define NXP_UICC_PWR_REQUEST 0x00U + +/**< UICC Bit Rate Configuration + 0x02U -> 212Kbits/Sec + 0x04U -> 424Kbits/Sec + 0x08U -> 828Kbits/Sec + */ + +#define NXP_UICC_BIT_RATE 0x08U + +/**< Indicates PN544 Power Modes Configuration for the NFC Device, + 0x00U -> PN544 stays in active bat mode + (except when generating RF field) + 0x01U -> PN544 goes in standby when possible otherwise + stays in active bat mode + 0x02U -> PN544 goes in idle mode as soon as it can + (otherwise it is in active bat except when generating RF field) + 0x03U -> PN544 goes in standby when possible otherwise goes in idle mode + as soon as it can (otherwise it is in active bat except when + generating RF field) + */ + +#define NXP_SYSTEM_PWR_STATUS 0x01U + + +/**< System Event Notification + 0x01 Overcurrent + 0x02 PMUVCC Switch + 0x04 External RF Field + 0x08 Memory Violation + 0x10 Temperature Overheat + */ + +#define NXP_SYSTEM_EVT_INFO 0x10U + +/**< NFCIP Active Mode Configuration + 0x01 106 kbps + 0x02 212 kbps + 0x04 424 kbps + */ + +#define NXP_NFCIP_ACTIVE_DEFAULT 0x01U + + + +/* Reset the Default values of Host Link Timers */ +/* Macro to Enable the Host Side Link Timeout Configuration + * 0x00 ----> Default Pre-defined Configuration; + * 0x01 ----> Update only the Host Link Guard Timeout Configuration; + * 0x03 ----> Update Both the Host Link Guard Timeout + and ACK Timeout Configuration; + */ +#define HOST_LINK_TIMEOUT 0x00U + + +#define NXP_NFC_LINK_GRD_CFG_DEFAULT 0x0032U + + +#define NXP_NFC_LINK_ACK_CFG_DEFAULT 0x0005U + + +/* Macro to Enable the Interface Character Timeout Configuration + * 0x00 ----> Default Pre-defined Configuration; + * 0x01 ----> Update the IFC Timeout Default Configuration; + */ +#define NXP_NFC_IFC_TIMEOUT 0x00 + + +#define NXP_NFC_IFC_CONFIG_DEFAULT 0x203AU + + +#define NXP_NFCIP_PSL_BRS_DEFAULT 0x00U + + +#endif /* NFC_CUSTOM_CONFIG_H */ |