1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
|
/*
* Copyright (C) 2010 NXP Semiconductors
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/**
* \file nfc_custom_config.h
* \brief HAL Custom Configurations
*
*
* \note This is the configuration header file of the HAL 4.0. custom configurable
* parameters of the HAL 4.0 are provided in this file
*
* Project: NFC-FRI-1.1 / HAL4.0
*
* $Date: Fri Jun 11 16:44:31 2010 $
* $Author: ing04880 $
* $Revision: 1.11 $
* $Aliases: NFC_FRI1.1_WK1023_R35_1 $
*
*/
/*@{*/
#ifndef NFC_CUSTOM_CONFIG_H
#define NFC_CUSTOM_CONFIG_H
/*@}*/
/**
* \name Hal
*
* File: \ref nfc_custom_config.h
*
*/
/*
*****************************************************************
********************** CUSTOM MACROS **************************
*****************************************************************
*/
/**< Max number of remote devices supported*/
#define MAX_REMOTE_DEVICES 0x10
/**< Default Session ID for Initialisation */
#define DEFAULT_SESSION "NXP-NFC2"
/** Resolution value for the timer, here the
timer resolution is 100 milliseconds */
#define TIMER_RESOLUTION 100U
/**< Defines connection time out value for LLC timer,
500 is in milliseconds */
#define LINK_CONNECTION_TIMEOUT 500U
/**< Defines guard time out value for LLC timer,
250 is in milliseconds */
#define LINK_GUARD_TIMEOUT 250U
/**< Macro to Enable SMX Feature During
* Initialisation */
/* PLEASE NOTE: This Macro should be only enabled if there is a SMART_MX
* Chip attached to the PN544.
*/
/* #define NXP_HAL_ENABLE_SMX */
/* PLEASE NOTE: Kindly change the DEFAULT_SESSION Macro for each of the
* configuration change done for the below Macros
*/
/**< External Clock Request Configuration for the NFC Device,
0x00U -> No Clock Request,
0x01U -> Clock Request through CLKREQ pin (GPIO pin 2),
0x02U -> Clock Request through NXP_EVT_CLK_REQUEST Event,
*/
#define NXP_DEFAULT_CLK_REQUEST 0x00U
/**< External Input Clock Setting for the NFC Device,
0x00U -> No Input Clock Required (Use the Xtal),
0x01U -> 13 MHZ,
0x02U -> 19.2 MHZ,
0x03U -> 26 MHZ,
0x04U -> 38.4 MHZ,
0x05U -> Custom (Set the Custome Clock Registry),
*/
#define NXP_DEFAULT_INPUT_CLK 0x00U
#define NFC_DEV_HWCONF_DEFAULT 0xBCU
/**< TX LDO Configuration
0x00 -> 00b 3.0 V,
0x01 -> 01b 3.0 V,
0x02 -> 10b 2.7 V,
0x03 -> 11b 3.3 V,
*/
#define NXP_DEFAULT_TX_LDO 0x00U
/**< External Clock Request Configuration for the NFC Device,
0x00U -> No Power Request,
0x01U -> Power Request through CLKREQ pin (GPIO pin 2),
0x02U -> Power Request through PWR_REQUEST (GPIO Pin 3),
*/
#define NXP_UICC_PWR_REQUEST 0x00U
/**< UICC Bit Rate Configuration
0x02U -> 212Kbits/Sec
0x04U -> 424Kbits/Sec
0x08U -> 828Kbits/Sec
*/
#define NXP_UICC_BIT_RATE 0x08U
/**< Indicates PN544 Power Modes Configuration for the NFC Device,
0x00U -> PN544 stays in active bat mode
(except when generating RF field)
0x01U -> PN544 goes in standby when possible otherwise
stays in active bat mode
0x02U -> PN544 goes in idle mode as soon as it can
(otherwise it is in active bat except when generating RF field)
0x03U -> PN544 goes in standby when possible otherwise goes in idle mode
as soon as it can (otherwise it is in active bat except when
generating RF field)
*/
#define NXP_SYSTEM_PWR_STATUS 0x01U
/**< System Event Notification
0x01 Overcurrent
0x02 PMUVCC Switch
0x04 External RF Field
0x08 Memory Violation
0x10 Temperature Overheat
*/
#define NXP_SYSTEM_EVT_INFO 0x10U
/**< NFCIP Active Mode Configuration
0x01 106 kbps
0x02 212 kbps
0x04 424 kbps
*/
#define NXP_NFCIP_ACTIVE_DEFAULT 0x01U
/* Reset the Default values of Host Link Timers */
/* Macro to Enable the Host Side Link Timeout Configuration
* 0x00 ----> Default Pre-defined Configuration;
* 0x01 ----> Update only the Host Link Guard Timeout Configuration;
* 0x03 ----> Update Both the Host Link Guard Timeout
and ACK Timeout Configuration;
*/
#define HOST_LINK_TIMEOUT 0x00U
#define NXP_NFC_LINK_GRD_CFG_DEFAULT 0x0032U
#define NXP_NFC_LINK_ACK_CFG_DEFAULT 0x0005U
/* Macro to Enable the Interface Character Timeout Configuration
* 0x00 ----> Default Pre-defined Configuration;
* 0x01 ----> Update the IFC Timeout Default Configuration;
*/
#define NXP_NFC_IFC_TIMEOUT 0x00
#define NXP_NFC_IFC_CONFIG_DEFAULT 0x203AU
#define NXP_NFCIP_PSL_BRS_DEFAULT 0x00U
#endif /* NFC_CUSTOM_CONFIG_H */
|
