1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
|
/*
* Copyright (C) 2008 The Android Open Source Project
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
#ifndef ANDROID_LIGHTS_INTERFACE_H
#define ANDROID_LIGHTS_INTERFACE_H
#include <stdint.h>
#include <sys/cdefs.h>
#include <sys/types.h>
#include <hardware/hardware.h>
__BEGIN_DECLS
/**
* The id of this module
*/
#define LIGHTS_HARDWARE_MODULE_ID "lights"
/*
* These light IDs correspond to logical lights, not physical.
* So for example, if your INDICATOR light is in line with your
* BUTTONS, it might make sense to also light the INDICATOR
* light to a reasonable color when the BUTTONS are lit.
*/
#define LIGHT_ID_BACKLIGHT "backlight"
#define LIGHT_ID_KEYBOARD "keyboard"
#define LIGHT_ID_BUTTONS "buttons"
#define LIGHT_ID_BATTERY "battery"
#define LIGHT_ID_NOTIFICATIONS "notifications"
#define LIGHT_ID_ATTENTION "attention"
/*
* These lights aren't currently supported by the higher
* layers, but could be someday, so we have the constants
* here now.
*/
#define LIGHT_ID_BLUETOOTH "bluetooth"
#define LIGHT_ID_WIFI "wifi"
/* ************************************************************************
* Flash modes for the flashMode field of light_state_t.
*/
#define LIGHT_FLASH_NONE 0
/**
* To flash the light at a given rate, set flashMode to LIGHT_FLASH_TIMED,
* and then flashOnMS should be set to the number of milliseconds to turn
* the light on, followed by the number of milliseconds to turn the light
* off.
*/
#define LIGHT_FLASH_TIMED 1
/**
* To flash the light using hardware assist, set flashMode to
* the hardware mode.
*/
#define LIGHT_FLASH_HARDWARE 2
/**
* Light brightness is managed by a user setting.
*/
#define BRIGHTNESS_MODE_USER 0
/**
* Light brightness is managed by a light sensor.
*/
#define BRIGHTNESS_MODE_SENSOR 1
/**
* The parameters that can be set for a given light.
*
* Not all lights must support all parameters. If you
* can do something backward-compatible, you should.
*/
struct light_state_t {
/**
* The color of the LED in ARGB.
*
* Do your best here.
* - If your light can only do red or green, if they ask for blue,
* you should do green.
* - If you can only do a brightness ramp, then use this formula:
* unsigned char brightness = ((77*((color>>16)&0x00ff))
* + (150*((color>>8)&0x00ff)) + (29*(color&0x00ff))) >> 8;
* - If you can only do on or off, 0 is off, anything else is on.
*
* The high byte should be ignored. Callers will set it to 0xff (which
* would correspond to 255 alpha).
*/
unsigned int color;
/**
* See the LIGHT_FLASH_* constants
*/
int flashMode;
int flashOnMS;
int flashOffMS;
/**
* Policy used by the framework to manage the light's brightness.
* Currently the values are BRIGHTNESS_MODE_USER and BRIGHTNESS_MODE_SENSOR.
*/
int brightnessMode;
};
struct light_device_t {
struct hw_device_t common;
/**
* Set the provided lights to the provided values.
*
* Returns: 0 on succes, error code on failure.
*/
int (*set_light)(struct light_device_t* dev,
struct light_state_t const* state);
};
__END_DECLS
#endif // ANDROID_LIGHTS_INTERFACE_H
|