Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC board updates from Olof Johansson:
 "Board updates for 3.12.  Again, a bit of domain overlap with SoC and
  DT branches, but most of this is around legacy code and board support.
  We've found that platform maintainers have a hard time separating all
  of these out and might move towards fewer branches for next release.

   - Removal of a number of Marvell Kirkwood board files, since contents
     is now common and mostly configured via DT.
   - Device-tree updates for Marvell Dove, including irqchip and
     clocksource setup.
   - Defconfig updates.  Gotta go somewhere.  One new one for Renesas
     Lager.
   - New backlight drivers for backlights used on Renesas shmobile
     platforms.
   - Removal of Renesas leds driver.
   - Shuffling of some of the new Broadcom platforms to give room for
     others in the same mach directory.  More in 3.13"

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
  mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
  mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
  ARM: bcm: Make secure API call optional
  ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
  ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
  ARM: bcm: Rename board_bcm
  mmc: sdhci-bcm-kona: make linker-section warning go away
  ARM: tegra: defconfig updates
  ARM: dove: add initial DT file for Globalscale D2Plug
  ARM: dove: add GPIO IR receiver node to SolidRun CuBox
  ARM: dove: add common pinmux functions to DT
  ARM: dove: add cpu device tree node
  ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
  arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
  ARM: kirkwood: fix DT building and update defconfig
  ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
  ARM: configs: disable DEBUG_LL in bcm_defconfig
  ARM: bcm281xx: Board specific reboot code
  ARM bcm281xx: Turn on socket & network support.
  ARM: bcm281xx: Turn on L2 cache.
  ...

111 files changed, 2416 insertions, 3040 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f9f4c4d..000cf76 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
 dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
 	dove-cubox.dtb \
+	dove-d2plug.dtb \
 	dove-dove-db.dtb
 dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
@@ -85,6 +86,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
 	kirkwood-lschlv2.dtb \
 	kirkwood-lsxhl.dtb \
 	kirkwood-mplcec4.dtb \
+	kirkwood-mv88f6281gtw-ge.dtb \
 	kirkwood-netgear_readynas_duo_v2.dtb \
 	kirkwood-ns2.dtb \
 	kirkwood-ns2lite.dtb \
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 5cae2ab..022646e 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -42,6 +42,8 @@
 			regulator-always-on;
 			regulator-boot-on;
 			gpio = <&gpio0 1 0>;
+			pinctrl-0 = <&pmx_gpio_1>;
+			pinctrl-names = "default";
 		};
 	};
 
@@ -53,10 +55,24 @@
 			clock-frequency = <25000000>;
 		};
 	};
+
+	ir_recv: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 19 1>;
+		pinctrl-0 = <&pmx_gpio_19>;
+		pinctrl-names = "default";
+	};
 };
 
 &uart0 { status = "okay"; };
 &sata0 { status = "okay"; };
+&mdio { status = "okay"; };
+&eth { status = "okay"; };
+
+&ethphy {
+	compatible = "marvell,88e1310";
+	reg = <1>;
+};
 
 &i2c0 {
 	status = "okay";
@@ -103,6 +119,7 @@
 	status = "okay";
 	/* sdio0 card detect is connected to wrong pin on CuBox */
 	cd-gpios = <&gpio0 12 1>;
+	pinctrl-0 = <&pmx_sdio0 &pmx_gpio_12>;
 };
 
 &spi0 {
@@ -115,23 +132,3 @@
 		reg = <0>;
 	};
 };
-
-&pinctrl {
-	pinctrl-0 = <&pmx_gpio_1 &pmx_gpio_12>;
-	pinctrl-names = "default";
-
-	pmx_gpio_1: pmx-gpio-1 {
-		marvell,pins = "mpp1";
-		marvell,function = "gpio";
-	};
-
-	pmx_gpio_12: pmx-gpio-12 {
-		marvell,pins = "mpp12";
-		marvell,function = "gpio";
-	};
-
-	pmx_gpio_18: pmx-gpio-18 {
-		marvell,pins = "mpp18";
-		marvell,function = "gpio";
-	};
-};
diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/dove-d2plug.dts
new file mode 100644
index 0000000..e2222ce
--- /dev/null
+++ b/arch/arm/boot/dts/dove-d2plug.dts
@@ -0,0 +1,69 @@
+/dts-v1/;
+
+/include/ "dove.dtsi"
+
+/ {
+	model = "Globalscale D2Plug";
+	compatible = "globalscale,d2plug", "marvell,dove";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
+		pinctrl-names = "default";
+
+		wlan-ap {
+			label = "wlan-ap";
+			gpios = <&gpio0 0 1>;
+		};
+
+		wlan-act {
+			label = "wlan-act";
+			gpios = <&gpio0 1 1>;
+		};
+
+		bluetooth-act {
+			label = "bt-act";
+			gpios = <&gpio0 2 1>;
+		};
+	};
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&i2c0 { status = "okay"; };
+&mdio { status = "okay"; };
+&eth { status = "okay"; };
+
+/* Samsung M8G2F eMMC */
+&sdio0 {
+	status = "okay";
+	non-removable;
+	bus-width = <4>;
+};
+
+/* Marvell SD8787 WLAN/BT */
+&sdio1 {
+	status = "okay";
+	non-removable;
+	bus-width = <4>;
+};
+
+&spi0 {
+	status = "okay";
+
+	/* spi0.0: 4M Flash Macronix MX25L3205D */
+	spi-flash@0 {
+		compatible = "st,m25l3205d";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 6cab468..cc27916 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -10,6 +10,23 @@
 		gpio2 = &gpio2;
 	};
 
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "marvell,pj4a", "marvell,sheeva-v7";
+			device_type = "cpu";
+			next-level-cache = <&l2>;
+			reg = <0>;
+		};
+	};
+
+	l2: l2-cache {
+		compatible = "marvell,tauros2-cache";
+		marvell,tauros2-cache-features = <0>;
+	};
+
 	soc@f1000000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -25,16 +42,28 @@
 		          0xf2100000 0xf2100000 0x0100000   /* PCIe0 I/O   1M */
 		          0xf8000000 0xf8000000 0x8000000>; /* BootROM   128M */
 
-		l2: l2-cache {
-			compatible = "marvell,tauros2-cache";
-			marvell,tauros2-cache-features = <0>;
+		timer: timer@20300 {
+			compatible = "marvell,orion-timer";
+			reg = <0x20300 0x20>;
+			interrupt-parent = <&bridge_intc>;
+			interrupts = <1>, <2>;
+			clocks = <&core_clk 0>;
 		};
 
-		intc: interrupt-controller {
+		intc: main-interrupt-ctrl@20200 {
 			compatible = "marvell,orion-intc";
 			interrupt-controller;
 			#interrupt-cells = <1>;
-			reg = <0x20204 0x04>, <0x20214 0x04>;
+			reg = <0x20200 0x10>, <0x20210 0x10>;
+		};
+
+		bridge_intc: bridge-interrupt-ctrl@20110 {
+			compatible = "marvell,orion-bridge-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x20110 0x8>;
+			interrupts = <0>;
+			marvell,#interrupts = <5>;
 		};
 
 		core_clk: core-clocks@d0214 {
@@ -43,14 +72,14 @@
 			#clock-cells = <1>;
 		};
 
-		gate_clk: clock-gating-control@d0038 {
+		gate_clk: clock-gating-ctrl@d0038 {
 			compatible = "marvell,dove-gating-clock";
 			reg = <0xd0038 0x4>;
 			clocks = <&core_clk 0>;
 			#clock-cells = <1>;
 		};
 
-		thermal: thermal@d001c {
+		thermal: thermal-diode@d001c {
 			compatible = "marvell,dove-thermal";
 			reg = <0xd001c 0x0c>, <0xd005c 0x08>;
 		};
@@ -70,6 +99,8 @@
 			reg-shift = <2>;
 			interrupts = <8>;
 			clocks = <&core_clk 0>;
+			pinctrl-0 = <&pmx_uart1>;
+			pinctrl-names = "default";
 			status = "disabled";
 		};
 
@@ -91,7 +122,7 @@
 			status = "disabled";
 		};
 
-		gpio0: gpio@d0400 {
+		gpio0: gpio-ctrl@d0400 {
 			compatible = "marvell,orion-gpio";
 			#gpio-cells = <2>;
 			gpio-controller;
@@ -102,7 +133,7 @@
 			interrupts = <12>, <13>, <14>, <60>;
 		};
 
-		gpio1: gpio@d0420 {
+		gpio1: gpio-ctrl@d0420 {
 			compatible = "marvell,orion-gpio";
 			#gpio-cells = <2>;
 			gpio-controller;
@@ -113,7 +144,7 @@
 			interrupts = <61>;
 		};
 
-		gpio2: gpio@e8400 {
+		gpio2: gpio-ctrl@e8400 {
 			compatible = "marvell,orion-gpio";
 			#gpio-cells = <2>;
 			gpio-controller;
@@ -121,13 +152,188 @@
 			ngpios = <8>;
 		};
 
-		pinctrl: pinctrl@d0200 {
+		pinctrl: pin-ctrl@d0200 {
 			compatible = "marvell,dove-pinctrl";
 			reg = <0xd0200 0x10>;
 			clocks = <&gate_clk 22>;
+
+			pmx_gpio_0: pmx-gpio-0 {
+				marvell,pins = "mpp0";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_1: pmx-gpio-1 {
+				marvell,pins = "mpp1";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_2: pmx-gpio-2 {
+				marvell,pins = "mpp2";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_3: pmx-gpio-3 {
+				marvell,pins = "mpp3";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_4: pmx-gpio-4 {
+				marvell,pins = "mpp4";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_5: pmx-gpio-5 {
+				marvell,pins = "mpp5";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_6: pmx-gpio-6 {
+				marvell,pins = "mpp6";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_7: pmx-gpio-7 {
+				marvell,pins = "mpp7";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_8: pmx-gpio-8 {
+				marvell,pins = "mpp8";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_9: pmx-gpio-9 {
+				marvell,pins = "mpp9";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_10: pmx-gpio-10 {
+				marvell,pins = "mpp10";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_11: pmx-gpio-11 {
+				marvell,pins = "mpp11";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_12: pmx-gpio-12 {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_13: pmx-gpio-13 {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_14: pmx-gpio-14 {
+				marvell,pins = "mpp14";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_15: pmx-gpio-15 {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_16: pmx-gpio-16 {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_17: pmx-gpio-17 {
+				marvell,pins = "mpp17";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_18: pmx-gpio-18 {
+				marvell,pins = "mpp18";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_19: pmx-gpio-19 {
+				marvell,pins = "mpp19";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_20: pmx-gpio-20 {
+				marvell,pins = "mpp20";
+				marvell,function = "gpio";
+			};
+
+			pmx_gpio_21: pmx-gpio-21 {
+				marvell,pins = "mpp21";
+				marvell,function = "gpio";
+			};
+
+			pmx_camera: pmx-camera {
+				marvell,pins = "mpp_camera";
+				marvell,function = "camera";
+			};
+
+			pmx_camera_gpio: pmx-camera-gpio {
+				marvell,pins = "mpp_camera";
+				marvell,function = "gpio";
+			};
+
+			pmx_sdio0: pmx-sdio0 {
+				marvell,pins = "mpp_sdio0";
+				marvell,function = "sdio0";
+			};
+
+			pmx_sdio0_gpio: pmx-sdio0-gpio {
+				marvell,pins = "mpp_sdio0";
+				marvell,function = "gpio";
+			};
+
+			pmx_sdio1: pmx-sdio1 {
+				marvell,pins = "mpp_sdio1";
+				marvell,function = "sdio1";
+			};
+
+			pmx_sdio1_gpio: pmx-sdio1-gpio {
+				marvell,pins = "mpp_sdio1";
+				marvell,function = "gpio";
+			};
+
+			pmx_audio1_gpio: pmx-audio1-gpio {
+				marvell,pins = "mpp_audio1";
+				marvell,function = "gpio";
+			};
+
+			pmx_spi0: pmx-spi0 {
+				marvell,pins = "mpp_spi0";
+				marvell,function = "spi0";
+			};
+
+			pmx_spi0_gpio: pmx-spi0-gpio {
+				marvell,pins = "mpp_spi0";
+				marvell,function = "gpio";
+			};
+
+			pmx_uart1: pmx-uart1 {
+				marvell,pins = "mpp_uart1";
+				marvell,function = "uart1";
+			};
+
+			pmx_uart1_gpio: pmx-uart1-gpio {
+				marvell,pins = "mpp_uart1";
+				marvell,function = "gpio";
+			};
+
+			pmx_nand: pmx-nand {
+				marvell,pins = "mpp_nand";
+				marvell,function = "nand";
+			};
+
+			pmx_nand_gpo: pmx-nand-gpo {
+				marvell,pins = "mpp_nand";
+				marvell,function = "gpo";
+			};
 		};
 
-		spi0: spi@10600 {
+		spi0: spi-ctrl@10600 {
 			compatible = "marvell,orion-spi";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -135,10 +341,12 @@
 			interrupts = <6>;
 			reg = <0x10600 0x28>;
 			clocks = <&core_clk 0>;
+			pinctrl-0 = <&pmx_spi0>;
+			pinctrl-names = "default";
 			status = "disabled";
 		};
 
-		spi1: spi@14600 {
+		spi1: spi-ctrl@14600 {
 			compatible = "marvell,orion-spi";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -149,7 +357,7 @@
 			status = "disabled";
 		};
 
-		i2c0: i2c@11000 {
+		i2c0: i2c-ctrl@11000 {
 			compatible = "marvell,mv64xxx-i2c";
 			reg = <0x11000 0x20>;
 			#address-cells = <1>;
@@ -177,23 +385,27 @@
 			status = "okay";
 		};
 
-		sdio0: sdio@92000 {
+		sdio0: sdio-host@92000 {
 			compatible = "marvell,dove-sdhci";
 			reg = <0x92000 0x100>;
 			interrupts = <35>, <37>;
 			clocks = <&gate_clk 8>;
+			pinctrl-0 = <&pmx_sdio0>;
+			pinctrl-names = "default";
 			status = "disabled";
 		};
 
-		sdio1: sdio@90000 {
+		sdio1: sdio-host@90000 {
 			compatible = "marvell,dove-sdhci";
 			reg = <0x90000 0x100>;
 			interrupts = <36>, <38>;
 			clocks = <&gate_clk 9>;
+			pinctrl-0 = <&pmx_sdio1>;
+			pinctrl-names = "default";
 			status = "disabled";
 		};
 
-		sata0: sata@a0000 {
+		sata0: sata-host@a0000 {
 			compatible = "marvell,orion-sata";
 			reg = <0xa0000 0x2400>;
 			interrupts = <62>;
@@ -202,12 +414,12 @@
 			status = "disabled";
 		};
 
-		rtc@d8500 {
+		rtc: real-time-clock@d8500 {
 			compatible = "marvell,orion-rtc";
 			reg = <0xd8500 0x20>;
 		};
 
-		crypto: crypto@30000 {
+		crypto: crypto-engine@30000 {
 			compatible = "marvell,orion-crypto";
 			reg = <0x30000 0x10000>,
 			      <0xc8000000 0x800>;
@@ -258,5 +470,40 @@
 				dmacap,xor;
 			};
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <30>;
+			clocks = <&gate_clk 2>;
+			status = "disabled";
+
+			ethphy: ethernet-phy {
+				device-type = "ethernet-phy";
+				/* set phy address in board file */
+			};
+		};
+
+		eth: ethernet-controller@72000 {
+			compatible = "marvell,orion-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			clocks = <&gate_clk 2>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet-port@0 {
+				device_type = "network";
+				compatible = "marvell,orion-eth-port";
+				reg = <0>;
+				interrupts = <29>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				phy-handle = <&ethphy>;
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/kirkwood-cloudbox.dts b/arch/arm/boot/dts/kirkwood-cloudbox.dts
index 9bf139c..142b9cd 100644
--- a/arch/arm/boot/dts/kirkwood-cloudbox.dts
+++ b/arch/arm/boot/dts/kirkwood-cloudbox.dts
@@ -89,3 +89,19 @@
 		gpios = <&gpio0 17 0>;
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/kirkwood-db.dtsi
index 45c1bf7..c0e2a58 100644
--- a/arch/arm/boot/dts/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/kirkwood-db.dtsi
@@ -79,3 +79,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
index 2e04284..d544f77 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
@@ -219,3 +219,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts
index 4387ae8..59a2117 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
@@ -90,3 +90,20 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1116";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
index c628378..6f62af9 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -99,3 +99,31 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index e571180..6f7c7d7 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -170,3 +170,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
index 2c5673a..6548b9d 100644
--- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
+++ b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
@@ -96,3 +96,33 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1121";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1121";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts
index 158161f..cb711a3 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
@@ -122,3 +122,19 @@
 
 
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index 8314118..0323f01 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -179,3 +179,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@11 {
+		device_type = "ethernet-phy";
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
index fd7f053..df84474 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -194,3 +194,27 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy1: ethernet-phy@11 {
+		device_type = "ethernet-phy";
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-is2.dts b/arch/arm/boot/dts/kirkwood-is2.dts
index bd88a23..da674bb 100644
--- a/arch/arm/boot/dts/kirkwood-is2.dts
+++ b/arch/arm/boot/dts/kirkwood-is2.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
index b071d37..6899408 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
@@ -50,3 +50,19 @@
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
index f7e247c..4e8f9e4 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
@@ -207,3 +207,31 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts
index 21f1954..ce2b94b 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts
@@ -194,3 +194,30 @@
 	};
 };
 
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		reg = <1>;
+	};
+
+	ethphy1: ethernet-phy@2 {
+		device_type = "ethernet-phy";
+		reg = <2>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
new file mode 100644
index 0000000..6317e1d
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -0,0 +1,125 @@
+/*
+ * Marvell 88F6281 GTW GE Board
+ *
+ * Lennert Buytenhek <buytenh@marvell.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * This file contains the definitions that are common between the 6281
+ * and 6282 variants of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Marvell 88F6281 GTW GE Board";
+	compatible = "marvell,mv88f6281gtw-ge", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	ocp@f1000000 {
+		pinctrl@10000 {
+			pmx_usb_led: pmx-usb-led {
+				marvell,pins = "mpp12";
+				marvell,function = "gpo";
+			};
+
+			pmx_leds: pmx-leds {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "gpio";
+			};
+
+			pmx_keys: pmx-keys {
+				marvell,pins = "mpp46", "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+
+		spi@10600 {
+			pinctrl-0 = <&pmx_spi>;
+			pinctrl-names = "default";
+			status = "okay";
+
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "mx25l12805d";
+				reg = <0>;
+				spi-max-frequency = <50000000>;
+				mode = <0>;
+			};
+		};
+
+		serial@12000 {
+			pinctrl-0 = <&pmx_uart0>;
+			pinctrl-names = "default";
+			clock-frequency = <200000000>;
+			status = "ok";
+		};
+
+		ehci@50000 {
+			status = "okay";
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds &pmx_usb_led>;
+		pinctrl-names = "default";
+
+		green-status {
+			label = "gtw:green:Status";
+			gpios = <&gpio0 20 0>;
+		};
+
+		red-status {
+			label = "gtw:red:Status";
+			gpios = <&gpio0 21 0>;
+		};
+
+		green-usb {
+			label = "gtw:green:USB";
+			gpios = <&gpio0 12 0>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_keys>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "SWR Button";
+			linux,code = <0x198>; /* KEY_RESTART */
+			gpios = <&gpio1 15 1>;
+		};
+		button@2 {
+			label = "WPS Button";
+			linux,code = <0x211>; /* KEY_WPS_BUTTON */
+			gpios = <&gpio1 14 1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
index cc40f19..874857e 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
@@ -207,3 +207,19 @@
                 };
         };
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
index d0fb34d..2fcb82e 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
@@ -84,3 +84,19 @@
 	};
 
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+                /* overwrite reg property in board file */
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ns2.dts b/arch/arm/boot/dts/kirkwood-ns2.dts
index 0599f3c..53368d1 100644
--- a/arch/arm/boot/dts/kirkwood-ns2.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2lite.dts b/arch/arm/boot/dts/kirkwood-ns2lite.dts
index b0e1798..2796070 100644
--- a/arch/arm/boot/dts/kirkwood-ns2lite.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2lite.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2max.dts b/arch/arm/boot/dts/kirkwood-ns2max.dts
index d4f6a58..defdc77 100644
--- a/arch/arm/boot/dts/kirkwood-ns2max.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2max.dts
@@ -49,3 +49,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2mini.dts b/arch/arm/boot/dts/kirkwood-ns2mini.dts
index f30e05a..adbafdd 100644
--- a/arch/arm/boot/dts/kirkwood-ns2mini.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2mini.dts
@@ -50,3 +50,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
index 365b792..85ccf8d 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
@@ -166,3 +166,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
index 0cc5f26..5696b63 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
@@ -91,3 +91,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts
index 974f1e0..30842b4 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/kirkwood-topkick.dts
@@ -203,3 +203,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
index 3867ae3..f755bc1 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6281.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
@@ -50,4 +50,6 @@
 			gpios = <&gpio0 16 1>;
 		};
 	};
-};
\ No newline at end of file
+};
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
index 04f6fe1..9efcd2d 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
@@ -61,4 +61,6 @@
 			gpios = <&gpio1 5 1>;
 		};
 	};
-};
\ No newline at end of file
+};
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/kirkwood-ts219.dtsi
index 7019cf6..39158cf 100644
--- a/arch/arm/boot/dts/kirkwood-ts219.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ts219.dtsi
@@ -99,3 +99,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+                /* overwrite reg property in board file */
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 70f414d..cf7aeaf 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -22,13 +22,6 @@
 	       gpio0 = &gpio0;
 	       gpio1 = &gpio1;
 	};
-	intc: interrupt-controller {
-		compatible = "marvell,orion-intc", "marvell,intc";
-		interrupt-controller;
-		#interrupt-cells = <1>;
-		reg = <0xf1020204 0x04>,
-		      <0xf1020214 0x04>;
-	};
 
 	mbus {
 		compatible = "marvell,kirkwood-mbus", "simple-bus";
@@ -52,6 +45,30 @@
 			reg = <0x20000 0x80>, <0x1500 0x20>;
 		};
 
+		timer: timer@20300 {
+			compatible = "marvell,orion-timer";
+			reg = <0x20300 0x20>;
+			interrupt-parent = <&bridge_intc>;
+			interrupts = <1>, <2>;
+			clocks = <&core_clk 0>;
+		};
+
+		intc: main-interrupt-ctrl@20200 {
+			compatible = "marvell,orion-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x20200 0x10>, <0x20210 0x10>;
+		};
+
+		bridge_intc: bridge-interrupt-ctrl@20110 {
+			compatible = "marvell,orion-bridge-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x20110 0x8>;
+			interrupts = <1>;
+			marvell,#interrupts = <6>;
+		};
+
 		core_clk: core-clocks@10030 {
 			compatible = "marvell,kirkwood-core-clock";
 			reg = <0x10030 0x4>;
@@ -118,9 +135,11 @@
 			#clock-cells = <1>;
 		};
 
-		wdt@20300 {
+		wdt: watchdog-timer@20300 {
 			compatible = "marvell,orion-wdt";
 			reg = <0x20300 0x28>;
+			interrupt-parent = <&bridge_intc>;
+			interrupts = <3>;
 			clocks = <&gate_clk 7>;
 			status = "okay";
 		};
@@ -207,5 +226,57 @@
 			clocks = <&gate_clk 17>;
 			status = "okay";
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <46>;
+			clocks = <&gate_clk 0>;
+			status = "disabled";
+
+			/* add phy nodes in board file */
+		};
+
+		eth0: ethernet-controller@72000 {
+			compatible = "marvell,kirkwood-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			clocks = <&gate_clk 0>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet0-port@0 {
+				device_type = "network";
+				compatible = "marvell,kirkwood-eth-port";
+				reg = <0>;
+				interrupts = <11>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
+
+		eth1: ethernet-controller@76000 {
+			compatible = "marvell,kirkwood-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x76000 0x4000>;
+			clocks = <&gate_clk 19>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet1-port@0 {
+				device_type = "network";
+				compatible = "marvell,kirkwood-eth-port";
+				reg = <0>;
+				interrupts = <15>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
index 0077fc8..aed83de 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -53,3 +53,20 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		device-type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/orion5x.dtsi
index 892c64e..e06c37e 100644
--- a/arch/arm/boot/dts/orion5x.dtsi
+++ b/arch/arm/boot/dts/orion5x.dtsi
@@ -16,11 +16,12 @@
 	aliases {
 		gpio0 = &gpio0;
 	};
+
 	intc: interrupt-controller {
-		compatible = "marvell,orion-intc", "marvell,intc";
+		compatible = "marvell,orion-intc";
 		interrupt-controller;
 		#interrupt-cells = <1>;
-		reg = <0xf1020204 0x04>;
+		reg = <0xf1020200 0x08>;
 	};
 
 	ocp@f1000000 {
@@ -132,5 +133,34 @@
 			interrupts = <28>;
 			status = "okay";
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <22>;
+			status = "disabled";
+
+			/* add phy nodes in board file */
+		};
+
+		eth: ethernet-controller@72000 {
+			compatible = "marvell,orion-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet-port@0 {
+				device_type = "network";
+				compatible = "marvell,orion-eth-port";
+				reg = <0>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
 	};
 };
diff --git a/arch/arm/configs/ape6evm_defconfig b/arch/arm/configs/ape6evm_defconfig
index dab5a7d..1ce3994 100644
--- a/arch/arm/configs/ape6evm_defconfig
+++ b/arch/arm/configs/ape6evm_defconfig
@@ -54,7 +54,8 @@ CONFIG_NETDEVICES=y
 CONFIG_SMC91X=y
 CONFIG_SMSC911X=y
 # CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_KEYBOARD is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
 CONFIG_SERIAL_NONSTANDARD=y
@@ -71,6 +72,9 @@ CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_GPIO=y
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
 # CONFIG_IOMMU_SUPPORT is not set
 # CONFIG_DNOTIFY is not set
 CONFIG_TMPFS=y
diff --git a/arch/arm/configs/bcm_defconfig b/arch/arm/configs/bcm_defconfig
index 65edf6d..6e49310 100644
--- a/arch/arm/configs/bcm_defconfig
+++ b/arch/arm/configs/bcm_defconfig
@@ -42,6 +42,18 @@ CONFIG_VFP=y
 CONFIG_NEON=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 CONFIG_PM_RUNTIME=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=y
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_ARPD=y
+CONFIG_SYN_COOKIES=y
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_PROC_DEVICETREE=y
@@ -112,7 +124,6 @@ CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=110
 CONFIG_BOOTPARAM_HUNG_TASK_PANIC=y
 CONFIG_DEBUG_INFO=y
 # CONFIG_FTRACE is not set
-CONFIG_DEBUG_LL=y
 CONFIG_CRC_CCITT=y
 CONFIG_CRC_T10DIF=y
 CONFIG_CRC_ITU_T=y
diff --git a/arch/arm/configs/dove_defconfig b/arch/arm/configs/dove_defconfig
index 4364eff..1101054 100644
--- a/arch/arm/configs/dove_defconfig
+++ b/arch/arm/configs/dove_defconfig
@@ -13,6 +13,9 @@ CONFIG_ARCH_DOVE=y
 CONFIG_MACH_DOVE_DB=y
 CONFIG_MACH_CM_A510=y
 CONFIG_MACH_DOVE_DT=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCI_MVEBU=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
@@ -78,6 +81,7 @@ CONFIG_SPI_ORION=y
 CONFIG_THERMAL=y
 CONFIG_DOVE_THERMAL=y
 CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 CONFIG_USB_STORAGE=y
diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
index 0f2aa61..0ae0eaeb 100644
--- a/arch/arm/configs/kirkwood_defconfig
+++ b/arch/arm/configs/kirkwood_defconfig
@@ -10,49 +10,18 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_ARCH_KIRKWOOD=y
 CONFIG_MACH_D2NET_V2=y
-CONFIG_MACH_DB88F6281_BP=y
-CONFIG_MACH_DOCKSTAR=y
-CONFIG_MACH_ESATA_SHEEVAPLUG=y
-CONFIG_MACH_GURUPLUG=y
-CONFIG_MACH_INETSPACE_V2=y
-CONFIG_MACH_MV88F6281GTW_GE=y
 CONFIG_MACH_NET2BIG_V2=y
 CONFIG_MACH_NET5BIG_V2=y
-CONFIG_MACH_NETSPACE_MAX_V2=y
-CONFIG_MACH_NETSPACE_V2=y
 CONFIG_MACH_OPENRD_BASE=y
 CONFIG_MACH_OPENRD_CLIENT=y
 CONFIG_MACH_OPENRD_ULTIMATE=y
 CONFIG_MACH_RD88F6192_NAS=y
 CONFIG_MACH_RD88F6281=y
-CONFIG_MACH_SHEEVAPLUG=y
 CONFIG_MACH_T5325=y
 CONFIG_MACH_TS219=y
 CONFIG_MACH_TS41X=y
-CONFIG_MACH_CLOUDBOX_DT=y
-CONFIG_MACH_DB88F628X_BP_DT=y
-CONFIG_MACH_DLINK_KIRKWOOD_DT=y
-CONFIG_MACH_DOCKSTAR_DT=y
-CONFIG_MACH_DREAMPLUG_DT=y
-CONFIG_MACH_GOFLEXNET_DT=y
-CONFIG_MACH_GURUPLUG_DT=y
-CONFIG_MACH_IB62X0_DT=y
-CONFIG_MACH_ICONNECT_DT=y
-CONFIG_MACH_INETSPACE_V2_DT=y
-CONFIG_MACH_IOMEGA_IX2_200_DT=y
-CONFIG_MACH_KM_KIRKWOOD_DT=y
-CONFIG_MACH_LSXL_DT=y
-CONFIG_MACH_MPLCEC4_DT=y
-CONFIG_MACH_NETSPACE_LITE_V2_DT=y
-CONFIG_MACH_NETSPACE_MAX_V2_DT=y
-CONFIG_MACH_NETSPACE_MINI_V2_DT=y
-CONFIG_MACH_NETSPACE_V2_DT=y
-CONFIG_MACH_NSA310_DT=y
-CONFIG_MACH_OPENBLOCKS_A6_DT=y
-CONFIG_MACH_READYNAS_DT=y
-CONFIG_MACH_SHEEVAPLUG_DT=y
-CONFIG_MACH_TOPKICK_DT=y
-CONFIG_MACH_TS219_DT=y
+CONFIG_ARCH_KIRKWOOD_DT=y
+CONFIG_MACH_MV88F6281GTW_GE_DT=y
 # CONFIG_CPU_FEROCEON_OLD_ID is not set
 CONFIG_PCI_MVEBU=y
 CONFIG_PREEMPT=y
@@ -92,6 +61,7 @@ CONFIG_MTD_M25P80=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ORION=y
 CONFIG_BLK_DEV_LOOP=y
+CONFIG_EEPROM_AT24=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=m
@@ -100,9 +70,9 @@ CONFIG_ATA=y
 CONFIG_SATA_AHCI=y
 CONFIG_SATA_MV=y
 CONFIG_NETDEVICES=y
-CONFIG_MII=y
 CONFIG_NET_DSA_MV88E6123_61_65=y
 CONFIG_MV643XX_ETH=y
+CONFIG_R8169=y
 CONFIG_MARVELL_PHY=y
 CONFIG_LIBERTAS=y
 CONFIG_LIBERTAS_SDIO=y
@@ -123,9 +93,11 @@ CONFIG_I2C_MV64XXX=y
 CONFIG_SPI=y
 CONFIG_SPI_ORION=y
 CONFIG_GPIO_SYSFS=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_ADT7475=y
+CONFIG_SENSORS_LM63=y
+CONFIG_SENSORS_LM75=y
+CONFIG_SENSORS_LM85=y
 CONFIG_THERMAL=y
-CONFIG_KIRKWOOD_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_ORION_WATCHDOG=y
 CONFIG_HID_DRAGONRISE=y
@@ -164,6 +136,8 @@ CONFIG_LEDS_TRIGGER_TIMER=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
 CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_RS5C372=y
+CONFIG_RTC_DRV_PCF8563=y
 CONFIG_RTC_DRV_S35390A=y
 CONFIG_RTC_DRV_MV=y
 CONFIG_DMADEVICES=y
@@ -171,6 +145,7 @@ CONFIG_MV_XOR=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
 CONFIG_ISO9660_FS=m
 CONFIG_JOLIET=y
 CONFIG_UDF_FS=m
@@ -186,12 +161,12 @@ CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_2=y
 CONFIG_NLS_UTF8=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/lager_defconfig b/arch/arm/configs/lager_defconfig
new file mode 100644
index 0000000..e777ef2
--- /dev/null
+++ b/arch/arm/configs/lager_defconfig
@@ -0,0 +1,120 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+CONFIG_SLAB=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_SHMOBILE=y
+CONFIG_ARCH_R8A7790=y
+CONFIG_MACH_LAGER=y
+# CONFIG_SH_TIMER_TMU is not set
+# CONFIG_EM_TIMER_STI is not set
+CONFIG_ARM_ERRATA_430973=y
+CONFIG_ARM_ERRATA_458693=y
+CONFIG_ARM_ERRATA_460075=y
+CONFIG_ARM_ERRATA_743622=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_FORCE_MAX_ZONEORDER=13
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_KEXEC=y
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_PM_RUNTIME=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_NETDEVICES=y
+# CONFIG_NET_CORE is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+CONFIG_SH_ETH=y
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_SH_SCI=y
+CONFIG_SERIAL_SH_SCI_NR_UARTS=10
+CONFIG_SERIAL_SH_SCI_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_GPIO=y
+CONFIG_I2C_SH_MOBILE=y
+CONFIG_GPIO_SH_PFC=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_RCAR=y
+# CONFIG_HWMON is not set
+CONFIG_THERMAL=y
+CONFIG_RCAR_THERMAL=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_SDHI=y
+CONFIG_MMC_SH_MMCIF=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_SH_DMAE=y
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+# CONFIG_ARM_UNWIND is not set
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
diff --git a/arch/arm/configs/marzen_defconfig b/arch/arm/configs/marzen_defconfig
index c50e52b..000e920 100644
--- a/arch/arm/configs/marzen_defconfig
+++ b/arch/arm/configs/marzen_defconfig
@@ -29,6 +29,7 @@ CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
 CONFIG_CMDLINE="console=ttySC2,115200 earlyprintk=sh-sci.2,115200 ignore_loglevel root=/dev/nfs ip=on"
 CONFIG_CMDLINE_FORCE=y
 CONFIG_KEXEC=y
diff --git a/arch/arm/configs/mvebu_defconfig b/arch/arm/configs/mvebu_defconfig
index 731814e..594d706 100644
--- a/arch/arm/configs/mvebu_defconfig
+++ b/arch/arm/configs/mvebu_defconfig
@@ -39,6 +39,8 @@ CONFIG_MVNETA=y
 CONFIG_MARVELL_PHY=y
 CONFIG_MWIFIEX=y
 CONFIG_MWIFIEX_SDIO=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_I2C=y
diff --git a/arch/arm/configs/tegra_defconfig b/arch/arm/configs/tegra_defconfig
index 92d0a14..ea042e8 100644
--- a/arch/arm/configs/tegra_defconfig
+++ b/arch/arm/configs/tegra_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SYSVIPC=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
@@ -26,8 +27,11 @@ CONFIG_ARCH_TEGRA=y
 CONFIG_ARCH_TEGRA_2x_SOC=y
 CONFIG_ARCH_TEGRA_3x_SOC=y
 CONFIG_ARCH_TEGRA_114_SOC=y
-CONFIG_TEGRA_PCI=y
 CONFIG_TEGRA_EMC_SCALING_ENABLE=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCI_TEGRA=y
+CONFIG_PCIEPORTBUS=y
 CONFIG_SMP=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
@@ -92,6 +96,7 @@ CONFIG_ISL29003=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=y
+CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
@@ -106,6 +111,7 @@ CONFIG_RT2800USB=m
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
 CONFIG_KEYBOARD_TEGRA=y
+CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_MPU3050=y
 # CONFIG_LEGACY_PTYS is not set
@@ -178,6 +184,7 @@ CONFIG_SND_SOC_TEGRA_WM8903=y
 CONFIG_SND_SOC_TEGRA_TRIMSLICE=y
 CONFIG_SND_SOC_TEGRA_ALC5632=y
 CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_ACM=y
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index f112895..69d67f7 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -12,6 +12,7 @@ config ARCH_BCM
 	select GPIO_BCM
 	select SPARSE_IRQ
 	select TICK_ONESHOT
+	select CACHE_L2X0
 	help
 	  This enables support for system based on Broadcom SoCs.
 	  It currently supports the 'BCM281XX' family, which includes
diff --git a/arch/arm/mach-bcm/Makefile b/arch/arm/mach-bcm/Makefile
index 6adb6aec..e3d0303 100644
--- a/arch/arm/mach-bcm/Makefile
+++ b/arch/arm/mach-bcm/Makefile
@@ -1,5 +1,5 @@
 #
-# Copyright (C) 2012 Broadcom Corporation
+# Copyright (C) 2012-2013 Broadcom Corporation
 #
 # This program is free software; you can redistribute it and/or
 # modify it under the terms of the GNU General Public License as
@@ -10,6 +10,6 @@
 # of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 # GNU General Public License for more details.
 
-obj-$(CONFIG_ARCH_BCM)		:= board_bcm.o bcm_kona_smc.o bcm_kona_smc_asm.o
+obj-$(CONFIG_ARCH_BCM)		:= board_bcm281xx.o bcm_kona_smc.o bcm_kona_smc_asm.o kona.o
 plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_bcm_kona_smc_asm.o	:=-Wa,-march=armv7-a$(plus_sec)
diff --git a/arch/arm/mach-bcm/bcm_kona_smc.c b/arch/arm/mach-bcm/bcm_kona_smc.c
index 56d9d19..5e31e91 100644
--- a/arch/arm/mach-bcm/bcm_kona_smc.c
+++ b/arch/arm/mach-bcm/bcm_kona_smc.c
@@ -36,18 +36,20 @@ struct bcm_kona_smc_data {
 };
 
 static const struct of_device_id bcm_kona_smc_ids[] __initconst = {
-	{.compatible = "bcm,kona-smc"},
+	{.compatible = "brcm,kona-smc"},
+	{.compatible = "bcm,kona-smc"}, /* deprecated name */
 	{},
 };
 
 /* Map in the bounce area */
-void __init bcm_kona_smc_init(void)
+int __init bcm_kona_smc_init(void)
 {
 	struct device_node *node;
 
 	/* Read buffer addr and size from the device tree node */
 	node = of_find_matching_node(NULL, bcm_kona_smc_ids);
-	BUG_ON(!node);
+	if (!node)
+		return -ENODEV;
 
 	/* Don't care about size or flags of the DT node */
 	bridge_data.buffer_addr =
@@ -59,7 +61,9 @@ void __init bcm_kona_smc_init(void)
 
 	bridge_data.initialized = 1;
 
-	pr_info("Secure API initialized!\n");
+	pr_info("Kona Secure API initialized\n");
+
+	return 0;
 }
 
 /* __bcm_kona_smc() should only run on CPU 0, with pre-emption disabled */
diff --git a/arch/arm/mach-bcm/bcm_kona_smc.h b/arch/arm/mach-bcm/bcm_kona_smc.h
index 3bedbed1..d098a7e 100644
--- a/arch/arm/mach-bcm/bcm_kona_smc.h
+++ b/arch/arm/mach-bcm/bcm_kona_smc.h
@@ -64,7 +64,7 @@
 #define SSAPI_BRCM_START_VC_CORE	0x0E000008
 
 #ifndef	__ASSEMBLY__
-extern void bcm_kona_smc_init(void);
+extern int __init bcm_kona_smc_init(void);
 
 extern unsigned bcm_kona_smc(unsigned service_id,
 			     unsigned arg0,
diff --git a/arch/arm/mach-bcm/board_bcm.c b/arch/arm/mach-bcm/board_bcm281xx.c
index 2859932..8d9f931 100644
--- a/arch/arm/mach-bcm/board_bcm.c
+++ b/arch/arm/mach-bcm/board_bcm281xx.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2012 Broadcom Corporation
+ * Copyright (C) 2012-2013 Broadcom Corporation
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
@@ -21,23 +21,39 @@
 #include <asm/mach/time.h>
 #include <asm/hardware/cache-l2x0.h>
 
-
 #include "bcm_kona_smc.h"
+#include "kona.h"
 
 static int __init kona_l2_cache_init(void)
 {
 	if (!IS_ENABLED(CONFIG_CACHE_L2X0))
 		return 0;
 
+	if (bcm_kona_smc_init() < 0) {
+		pr_info("Kona secure API not available. Skipping L2 init\n");
+		return 0;
+	}
+
 	bcm_kona_smc(SSAPI_ENABLE_L2_CACHE, 0, 0, 0, 0);
 
 	/*
 	 * The aux_val and aux_mask have no effect since L2 cache is already
 	 * enabled.  Pass 0s for aux_val and 1s for aux_mask for default value.
 	 */
-	l2x0_of_init(0, ~0);
+	return l2x0_of_init(0, ~0);
+}
 
-	return 0;
+static void bcm_board_setup_restart(void)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "brcm,bcm11351");
+	if (np) {
+		if (of_device_is_available(np))
+			bcm_kona_setup_restart();
+		of_node_put(np);
+	}
+	/* Restart setup for other boards goes here */
 }
 
 static void __init board_init(void)
@@ -45,15 +61,15 @@ static void __init board_init(void)
 	of_platform_populate(NULL, of_default_bus_match_table, NULL,
 		&platform_bus);
 
-	bcm_kona_smc_init();
-
+	bcm_board_setup_restart();
 	kona_l2_cache_init();
 }
 
-static const char * const bcm11351_dt_compat[] = { "bcm,bcm11351", NULL, };
+static const char * const bcm11351_dt_compat[] = { "brcm,bcm11351", NULL, };
 
 DT_MACHINE_START(BCM11351_DT, "Broadcom Application Processor")
 	.init_time = clocksource_of_init,
 	.init_machine = board_init,
+	.restart = bcm_kona_restart,
 	.dt_compat = bcm11351_dt_compat,
 MACHINE_END
diff --git a/arch/arm/mach-bcm/kona.c b/arch/arm/mach-bcm/kona.c
new file mode 100644
index 0000000..6939d90
--- /dev/null
+++ b/arch/arm/mach-bcm/kona.c
@@ -0,0 +1,65 @@
+/*
+ * Copyright (C) 2013 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/of_address.h>
+#include <asm/io.h>
+
+#include "kona.h"
+
+static void __iomem *watchdog_base;
+
+void bcm_kona_setup_restart(void)
+{
+	struct device_node *np_wdog;
+
+	/*
+	 * The assumption is that whoever calls bcm_kona_setup_restart()
+	 * also needs a Kona Watchdog Timer entry in Device Tree, i.e. we
+	 * report an error if the DT entry is missing.
+	 */
+	np_wdog = of_find_compatible_node(NULL, NULL, "brcm,kona-wdt");
+	if (!np_wdog) {
+		pr_err("brcm,kona-wdt not found in DT, reboot disabled\n");
+		return;
+	}
+	watchdog_base = of_iomap(np_wdog, 0);
+	WARN(!watchdog_base, "failed to map watchdog base");
+	of_node_put(np_wdog);
+}
+
+#define SECWDOG_OFFSET			0x00000000
+#define SECWDOG_RESERVED_MASK		0xE2000000
+#define SECWDOG_WD_LOAD_FLAG_MASK	0x10000000
+#define SECWDOG_EN_MASK			0x08000000
+#define SECWDOG_SRSTEN_MASK		0x04000000
+#define SECWDOG_CLKS_SHIFT		20
+#define SECWDOG_LOCK_SHIFT		0
+
+void bcm_kona_restart(enum reboot_mode mode, const char *cmd)
+{
+	uint32_t val;
+
+	if (!watchdog_base)
+		panic("Watchdog not mapped. Reboot failed.\n");
+
+	/* Enable watchdog2 with very short timeout. */
+	val = readl(watchdog_base + SECWDOG_OFFSET);
+	val &= SECWDOG_RESERVED_MASK | SECWDOG_WD_LOAD_FLAG_MASK;
+	val |= SECWDOG_EN_MASK | SECWDOG_SRSTEN_MASK |
+		(0x8 << SECWDOG_CLKS_SHIFT) |
+		(0x8 << SECWDOG_LOCK_SHIFT);
+	writel(val, watchdog_base + SECWDOG_OFFSET);
+
+	while (1)
+		;
+}
diff --git a/arch/arm/mach-bcm/kona.h b/arch/arm/mach-bcm/kona.h
new file mode 100644
index 0000000..291eca3
--- /dev/null
+++ b/arch/arm/mach-bcm/kona.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2013 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/reboot.h>
+
+void bcm_kona_setup_restart(void);
+void bcm_kona_restart(enum reboot_mode mode, const char *cmd);
diff --git a/arch/arm/mach-dove/Kconfig b/arch/arm/mach-dove/Kconfig
index dff7b2f..0bc7cdf 100644
--- a/arch/arm/mach-dove/Kconfig
+++ b/arch/arm/mach-dove/Kconfig
@@ -23,6 +23,8 @@ config MACH_CM_A510
 config MACH_DOVE_DT
 	bool "Marvell Dove Flattened Device Tree"
 	select DOVE_CLK
+	select ORION_IRQCHIP
+	select ORION_TIMER
 	select REGULATOR
 	select REGULATOR_FIXED_VOLTAGE
 	select USE_OF
diff --git a/arch/arm/mach-dove/Makefile b/arch/arm/mach-dove/Makefile
index 4d9d2ff..cbc5c06 100644
--- a/arch/arm/mach-dove/Makefile
+++ b/arch/arm/mach-dove/Makefile
@@ -1,5 +1,5 @@
-obj-y				+= common.o irq.o
-obj-$(CONFIG_DOVE_LEGACY)	+= mpp.o
+obj-y				+= common.o
+obj-$(CONFIG_DOVE_LEGACY)	+= irq.o mpp.o
 obj-$(CONFIG_PCI)		+= pcie.o
 obj-$(CONFIG_MACH_DOVE_DB)	+= dove-db-setup.o
 obj-$(CONFIG_MACH_DOVE_DT)	+= board-dt.o
diff --git a/arch/arm/mach-dove/board-dt.c b/arch/arm/mach-dove/board-dt.c
index f3755ac..49f72a8 100644
--- a/arch/arm/mach-dove/board-dt.c
+++ b/arch/arm/mach-dove/board-dt.c
@@ -10,11 +10,14 @@
 
 #include <linux/init.h>
 #include <linux/clk-provider.h>
+#include <linux/clocksource.h>
+#include <linux/irqchip.h>
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/platform_data/usb-ehci-orion.h>
 #include <asm/hardware/cache-tauros2.h>
 #include <asm/mach/arch.h>
+#include <mach/dove.h>
 #include <mach/pm.h>
 #include <plat/common.h>
 #include <plat/irq.h>
@@ -33,10 +36,6 @@ static void __init dove_legacy_clk_init(void)
 	clkspec.np = np;
 	clkspec.args_count = 1;
 
-	clkspec.args[0] = CLOCK_GATING_BIT_GBE;
-	orion_clkdev_add(NULL, "mv643xx_eth_port.0",
-			 of_clk_get_from_provider(&clkspec));
-
 	clkspec.args[0] = CLOCK_GATING_BIT_PCIE0;
 	orion_clkdev_add("0", "pcie",
 			 of_clk_get_from_provider(&clkspec));
@@ -46,15 +45,18 @@ static void __init dove_legacy_clk_init(void)
 			 of_clk_get_from_provider(&clkspec));
 }
 
-static void __init dove_of_clk_init(void)
+static void __init dove_dt_time_init(void)
 {
 	of_clk_init(NULL);
-	dove_legacy_clk_init();
+	clocksource_of_init();
 }
 
-static struct mv643xx_eth_platform_data dove_dt_ge00_data = {
-	.phy_addr = MV643XX_ETH_PHY_ADDR_DEFAULT,
-};
+static void __init dove_dt_init_early(void)
+{
+	mvebu_mbus_init("marvell,dove-mbus",
+			BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
+			DOVE_MC_WINS_BASE, DOVE_MC_WINS_SZ);
+}
 
 static void __init dove_dt_init(void)
 {
@@ -65,11 +67,10 @@ static void __init dove_dt_init(void)
 #endif
 	dove_setup_cpu_wins();
 
-	/* Setup root of clk tree */
-	dove_of_clk_init();
+	/* Setup clocks for legacy devices */
+	dove_legacy_clk_init();
 
 	/* Internal devices not ported to DT yet */
-	dove_ge00_init(&dove_dt_ge00_data);
 	dove_pcie_init(1, 1);
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
@@ -82,9 +83,8 @@ static const char * const dove_dt_board_compat[] = {
 
 DT_MACHINE_START(DOVE_DT, "Marvell Dove (Flattened Device Tree)")
 	.map_io		= dove_map_io,
-	.init_early	= dove_init_early,
-	.init_irq	= orion_dt_init_irq,
-	.init_time	= dove_timer_init,
+	.init_early	= dove_dt_init_early,
+	.init_time	= dove_dt_time_init,
 	.init_machine	= dove_dt_init,
 	.restart	= dove_restart,
 	.dt_compat	= dove_dt_board_compat,
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index b634f96..fe8319a 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -2,67 +2,32 @@ if ARCH_KIRKWOOD
 
 menu "Marvell Kirkwood Implementations"
 
+config KIRKWOOD_LEGACY
+	bool
+
 config MACH_D2NET_V2
 	bool "LaCie d2 Network v2 NAS Board"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie d2 Network v2 NAS.
 
-config MACH_DOCKSTAR
-	bool "Seagate FreeAgent DockStar"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Seagate FreeAgent DockStar.
-
-config MACH_ESATA_SHEEVAPLUG
-	bool "Marvell eSATA SheevaPlug Reference Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell eSATA SheevaPlug Reference Board.
-
-config MACH_GURUPLUG
-	bool "Marvell GuruPlug Reference Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell GuruPlug Reference Board.
-
-config MACH_INETSPACE_V2
-	bool "LaCie Internet Space v2 NAS Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  LaCie Internet Space v2 NAS.
-
-config MACH_MV88F6281GTW_GE
-	bool "Marvell 88F6281 GTW GE Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell 88F6281 GTW GE Board.
-
 config MACH_NET2BIG_V2
 	bool "LaCie 2Big Network v2 NAS Board"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie 2Big Network v2 NAS.
 
 config MACH_NET5BIG_V2
 	bool "LaCie 5Big Network v2 NAS Board"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie 5Big Network v2 NAS.
 
-config MACH_NETSPACE_MAX_V2
-	bool "LaCie Network Space Max v2 NAS Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  LaCie Network Space Max v2 NAS.
-
-config MACH_NETSPACE_V2
-	bool "LaCie Network Space v2 NAS Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  LaCie Network Space v2 NAS.
-
 config MACH_OPENRD
+	select KIRKWOOD_LEGACY
         bool
 
 config MACH_OPENRD_BASE
@@ -88,30 +53,28 @@ config MACH_OPENRD_ULTIMATE
 
 config MACH_RD88F6192_NAS
 	bool "Marvell RD-88F6192-NAS Reference Board"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell RD-88F6192-NAS Reference Board.
 
 config MACH_RD88F6281
 	bool "Marvell RD-88F6281 Reference Board"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell RD-88F6281 Reference Board.
 
-config MACH_SHEEVAPLUG
-	bool "Marvell SheevaPlug Reference Board"
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell SheevaPlug Reference Board.
-
 config MACH_T5325
 	bool "HP t5325 Thin Client"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  HP t5325 Thin Client.
 
 config MACH_TS219
 	bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
@@ -119,6 +82,7 @@ config MACH_TS219
 
 config MACH_TS41X
 	bool "QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo NAS"
+	select KIRKWOOD_LEGACY
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
@@ -129,6 +93,9 @@ comment "Device tree entries"
 config ARCH_KIRKWOOD_DT
 	bool "Marvell Kirkwood Flattened Device Tree"
 	select KIRKWOOD_CLK
+	select OF_IRQ
+	select ORION_IRQCHIP
+	select ORION_TIMER
 	select POWER_SUPPLY
 	select POWER_RESET
 	select POWER_RESET_GPIO
@@ -139,184 +106,12 @@ config ARCH_KIRKWOOD_DT
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Kirkwood using flattened device tree.
 
-config MACH_CLOUDBOX_DT
-	bool "LaCie CloudBox NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  CloudBox NAS, using Flattened Device Tree.
-
-config MACH_DB88F628X_BP_DT
-	bool "Marvell DB-88F628x-BP Development Board (Flattened Device Tree)"
-	help
-	  Say 'Y' here if you want your kernel to support the Marvell
-	  DB-88F6281-BP and DB-88F6282-BP Development Board (Flattened
-	  Device Tree).
-
-config MACH_DLINK_KIRKWOOD_DT
-	bool "D-Link Kirkwood-based NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Kirkwood-based D-Link NASes such as DNS-320 & DNS-325,
-	  using Flattened Device Tree.
-
-config MACH_DOCKSTAR_DT
-	bool "Seagate FreeAgent Dockstar (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
+config MACH_MV88F6281GTW_GE_DT
+	bool "Marvell 88F6281 GTW GE Board (Flattened Device Tree)"
+	depends on ARCH_KIRKWOOD_DT
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  Seagate FreeAgent Dockstar (Flattened Device Tree).
-
-config MACH_DREAMPLUG_DT
-	bool "Marvell DreamPlug (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell DreamPlug (Flattened Device Tree).
-
-config MACH_GOFLEXNET_DT
-	bool "Seagate GoFlex Net (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Seagate GoFlex Net (Flattened Device Tree).
-
-config MACH_GURUPLUG_DT
-	bool "Marvell GuruPlug Reference Board (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell GuruPlug Reference Board (Flattened Device Tree).
-
-config MACH_IB62X0_DT
-	bool "RaidSonic IB-NAS6210, IB-NAS6220 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  RaidSonic IB-NAS6210 & IB-NAS6220 devices, using
-	  Flattened Device Tree.
-
-config MACH_ICONNECT_DT
-	bool "Iomega Iconnect (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here to enable Iomega Iconnect support.
-
-config MACH_INETSPACE_V2_DT
-	bool "LaCie Internet Space v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Internet Space v2 NAS, using Flattened Device Tree.
-
-config MACH_IOMEGA_IX2_200_DT
-	bool "Iomega StorCenter ix2-200 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Iomega StorCenter ix2-200 (Flattened Device Tree).
-
-config MACH_KM_KIRKWOOD_DT
-	bool "Keymile Kirkwood Reference Design (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Keymile Kirkwood Reference Desgin, using Flattened Device Tree.
-
-config MACH_LSXL_DT
-	bool "Buffalo Linkstation LS-XHL, LS-CHLv2 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	select POWER_RESET_RESTART
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Buffalo Linkstation LS-XHL & LS-CHLv2 devices, using
-	  Flattened Device Tree.
-
-config MACH_MPLCEC4_DT
-	bool "MPL CEC4 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  MPL CEC4 (Flattened Device Tree).
-
-config MACH_NETSPACE_LITE_V2_DT
-	bool "LaCie Network Space Lite v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Lite v2 NAS, using Flattened Device Tree.
-
-config MACH_NETSPACE_MAX_V2_DT
-	bool "LaCie Network Space Max v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Max v2 NAS, using Flattened Device Tree.
-
-config MACH_NETSPACE_MINI_V2_DT
-	bool "LaCie Network Space Mini v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Mini v2 NAS using Flattened Device Tree.
-
-	  This board is embedded in a product named CloudBox, which
-	  provides automatic backup on a 100GB cloud storage. This
-	  should not confused with a more recent LaCie NAS also named
-	  CloudBox. For this last, the disk capacity is 1TB or above.
-
-config MACH_NETSPACE_V2_DT
-	bool "LaCie Network Space v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space v2 NAS, using Flattened Device Tree.
-
-config MACH_OPENBLOCKS_A6_DT
-	bool "Plat'Home OpenBlocks A6 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Plat'Home OpenBlocks A6 (Flattened Device Tree).
-
-config MACH_READYNAS_DT
-	bool "NETGEAR ReadyNAS Duo v2 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	select ARM_APPENDED_DTB
-	select ARM_ATAG_DTB_COMPAT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  NETGEAR ReadyNAS Duo v2 using Fattened Device Tree.
-
-config MACH_SHEEVAPLUG_DT
-	bool "Marvell (eSATA) SheevaPlug (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell (eSATA) SheevaPlug (Flattened Device Tree).
-
-config MACH_TOPKICK_DT
-	bool "USI Topkick (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  USI Topkick, using Flattened Device Tree
-
-config MACH_TS219_DT
-	bool "Device Tree for QNAP TS-11X, TS-21X NAS"
-	select ARCH_KIRKWOOD_DT
-	select ARM_APPENDED_DTB
-	select ARM_ATAG_DTB_COMPAT
-	select POWER_RESET_QNAP
-	help
-	  Say 'Y' here if you want your kernel to support the QNAP
-	  TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
-	  TS-219P+ Turbo NAS devices using Fattened Device Tree.
-	  There are two different Device Tree descriptions, depending
-	  on if the device is based on an if the board uses the MV6281
-	  or MV6282. If you have the wrong one, the buttons will not
-	  work.
+	  Marvell 88F6281 GTW GE Board (Flattened Device Tree).
 
 endmenu
 
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index ac4cd75..d1f8e3d 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -1,44 +1,14 @@
-obj-y				+= common.o irq.o pcie.o mpp.o
-
+obj-y				+= common.o pcie.o
+obj-$(CONFIG_KIRKWOOD_LEGACY)	+= irq.o mpp.o
 obj-$(CONFIG_MACH_D2NET_V2)		+= d2net_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_DOCKSTAR)		+= dockstar-setup.o
-obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG)	+= sheevaplug-setup.o
-obj-$(CONFIG_MACH_GURUPLUG)		+= guruplug-setup.o
-obj-$(CONFIG_MACH_INETSPACE_V2)		+= netspace_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_MV88F6281GTW_GE)	+= mv88f6281gtw_ge-setup.o
 obj-$(CONFIG_MACH_NET2BIG_V2)		+= netxbig_v2-setup.o lacie_v2-common.o
 obj-$(CONFIG_MACH_NET5BIG_V2)		+= netxbig_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_NETSPACE_MAX_V2)	+= netspace_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_NETSPACE_V2)		+= netspace_v2-setup.o lacie_v2-common.o
 obj-$(CONFIG_MACH_OPENRD)		+= openrd-setup.o
 obj-$(CONFIG_MACH_RD88F6192_NAS)	+= rd88f6192-nas-setup.o
 obj-$(CONFIG_MACH_RD88F6281)		+= rd88f6281-setup.o
-obj-$(CONFIG_MACH_SHEEVAPLUG)		+= sheevaplug-setup.o
 obj-$(CONFIG_MACH_T5325)		+= t5325-setup.o
 obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_TS41X)		+= ts41x-setup.o tsx1x-common.o
 
 obj-$(CONFIG_ARCH_KIRKWOOD_DT)		+= board-dt.o
-obj-$(CONFIG_MACH_CLOUDBOX_DT)		+= board-ns2.o
-obj-$(CONFIG_MACH_DB88F628X_BP_DT)	+= board-db88f628x-bp.o
-obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT)	+= board-dnskw.o
-obj-$(CONFIG_MACH_DOCKSTAR_DT)		+= board-dockstar.o
-obj-$(CONFIG_MACH_DREAMPLUG_DT)		+= board-dreamplug.o
-obj-$(CONFIG_MACH_GOFLEXNET_DT)		+= board-goflexnet.o
-obj-$(CONFIG_MACH_GURUPLUG_DT)		+= board-guruplug.o
-obj-$(CONFIG_MACH_IB62X0_DT)		+= board-ib62x0.o
-obj-$(CONFIG_MACH_ICONNECT_DT)		+= board-iconnect.o
-obj-$(CONFIG_MACH_INETSPACE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT)	+= board-iomega_ix2_200.o
-obj-$(CONFIG_MACH_KM_KIRKWOOD_DT)	+= board-km_kirkwood.o
-obj-$(CONFIG_MACH_LSXL_DT)		+= board-lsxl.o
-obj-$(CONFIG_MACH_MPLCEC4_DT)		+= board-mplcec4.o
-obj-$(CONFIG_MACH_NETSPACE_LITE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_MAX_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_MINI_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_OPENBLOCKS_A6_DT)	+= board-openblocks_a6.o
-obj-$(CONFIG_MACH_READYNAS_DT)		+= board-readynas.o
-obj-$(CONFIG_MACH_SHEEVAPLUG_DT)	+= board-sheevaplug.o
-obj-$(CONFIG_MACH_TOPKICK_DT)		+= board-usi_topkick.o
-obj-$(CONFIG_MACH_TS219_DT)		+= board-ts219.o tsx1x-common.o
+obj-$(CONFIG_MACH_MV88F6281GTW_GE_DT)	+= board-mv88f6281gtw_ge.o
diff --git a/arch/arm/mach-kirkwood/board-db88f628x-bp.c b/arch/arm/mach-kirkwood/board-db88f628x-bp.c
deleted file mode 100644
index 2f574bc..0000000
--- a/arch/arm/mach-kirkwood/board-db88f628x-bp.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Saeed Bishara <saeed@marvell.com>
- *
- * Marvell DB-88F628{1,2}-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data db88f628x_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init db88f628x_init(void)
-{
-	kirkwood_ge00_init(&db88f628x_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dnskw.c b/arch/arm/mach-kirkwood/board-dnskw.c
deleted file mode 100644
index a1aa87f..0000000
--- a/arch/arm/mach-kirkwood/board-dnskw.c
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * Copyright 2012 (C), Jamie Lentin <jm@lentin.co.uk>
- *
- * arch/arm/mach-kirkwood/board-dnskw.c
- *
- * D-link DNS-320 & DNS-325 NAS Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dnskw_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/* Register any GPIO for output and set the value */
-static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
-{
-	if (gpio_request(gpio, name) == 0 &&
-	    gpio_direction_output(gpio, 0) == 0) {
-		gpio_set_value(gpio, def);
-		if (gpio_export(gpio, 0) != 0)
-			pr_err("dnskw: Failed to export GPIO %s\n", name);
-	} else
-		pr_err("dnskw: Failed to register %s\n", name);
-}
-
-void __init dnskw_init(void)
-{
-	kirkwood_ge00_init(&dnskw_ge00_data);
-
-	/* Set NAS to turn back on after a power failure */
-	dnskw_gpio_register(37, "dnskw:power:recover", 1);
-}
diff --git a/arch/arm/mach-kirkwood/board-dockstar.c b/arch/arm/mach-kirkwood/board-dockstar.c
deleted file mode 100644
index d7196db..0000000
--- a/arch/arm/mach-kirkwood/board-dockstar.c
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-dockstar.c
- *
- * Seagate FreeAgent Dockstar Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * Copied and modified for Seagate GoFlex Net support by
- * Joshua Coombs <josh.coombs@gmail.com> based on ArchLinux ARM's
- * GoFlex kernel patches.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dockstar_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init dockstar_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&dockstar_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dreamplug.c b/arch/arm/mach-kirkwood/board-dreamplug.c
deleted file mode 100644
index 0903242..0000000
--- a/arch/arm/mach-kirkwood/board-dreamplug.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-dreamplug.c
- *
- * Marvell DreamPlug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-void __init dreamplug_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&dreamplug_ge00_data);
-	kirkwood_ge01_init(&dreamplug_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 682b7ac..82d3ad8 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -15,6 +15,9 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/clk-provider.h>
+#include <linux/clocksource.h>
+#include <linux/dma-mapping.h>
+#include <linux/irqchip.h>
 #include <linux/kexec.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -49,10 +52,6 @@ static void __init kirkwood_legacy_clk_init(void)
 	orion_clkdev_add("1", "pcie",
 			 of_clk_get_from_provider(&clkspec));
 
-	clkspec.args[0] = CGC_BIT_SDIO;
-	orion_clkdev_add(NULL, "mvsdio",
-			 of_clk_get_from_provider(&clkspec));
-
 	/*
 	 * The ethernet interfaces forget the MAC address assigned by
 	 * u-boot if the clocks are turned off. Until proper DT support
@@ -60,19 +59,24 @@ static void __init kirkwood_legacy_clk_init(void)
 	 */
 	clkspec.args[0] = CGC_BIT_GE0;
 	clk = of_clk_get_from_provider(&clkspec);
-	orion_clkdev_add(NULL, "mv643xx_eth_port.0", clk);
 	clk_prepare_enable(clk);
 
 	clkspec.args[0] = CGC_BIT_GE1;
 	clk = of_clk_get_from_provider(&clkspec);
-	orion_clkdev_add(NULL, "mv643xx_eth_port.1", clk);
 	clk_prepare_enable(clk);
 }
 
-static void __init kirkwood_of_clk_init(void)
+static void __init kirkwood_dt_time_init(void)
 {
 	of_clk_init(NULL);
-	kirkwood_legacy_clk_init();
+	clocksource_of_init();
+}
+
+static void __init kirkwood_dt_init_early(void)
+{
+	mvebu_mbus_init("marvell,kirkwood-mbus",
+			BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
+			DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ);
 }
 
 static void __init kirkwood_dt_init(void)
@@ -94,8 +98,8 @@ static void __init kirkwood_dt_init(void)
 
 	kirkwood_cpufreq_init();
 
-	/* Setup root of clk tree */
-	kirkwood_of_clk_init();
+	/* Setup clocks for legacy devices */
+	kirkwood_legacy_clk_init();
 
 	kirkwood_cpuidle_init();
 
@@ -103,105 +107,22 @@ static void __init kirkwood_dt_init(void)
 	kexec_reinit = kirkwood_enable_pcie;
 #endif
 
-	if (of_machine_is_compatible("globalscale,dreamplug"))
-		dreamplug_init();
-
-	if (of_machine_is_compatible("globalscale,guruplug"))
-		guruplug_dt_init();
-
-	if (of_machine_is_compatible("globalscale,sheevaplug"))
-		sheevaplug_dt_init();
-
-	if (of_machine_is_compatible("dlink,dns-kirkwood"))
-		dnskw_init();
-
-	if (of_machine_is_compatible("iom,iconnect"))
-		iconnect_init();
-
-	if (of_machine_is_compatible("raidsonic,ib-nas62x0"))
-		ib62x0_init();
-
-	if (of_machine_is_compatible("qnap,ts219"))
-		qnap_dt_ts219_init();
-
-	if (of_machine_is_compatible("seagate,dockstar"))
-		dockstar_dt_init();
-
-	if (of_machine_is_compatible("seagate,goflexnet"))
-		goflexnet_init();
-
-	if (of_machine_is_compatible("buffalo,lsxl"))
-		lsxl_init();
-
-	if (of_machine_is_compatible("iom,ix2-200"))
-		iomega_ix2_200_init();
-
-	if (of_machine_is_compatible("keymile,km_kirkwood"))
-		km_kirkwood_init();
-
-	if (of_machine_is_compatible("lacie,cloudbox") ||
-	    of_machine_is_compatible("lacie,inetspace_v2") ||
-	    of_machine_is_compatible("lacie,netspace_lite_v2") ||
-	    of_machine_is_compatible("lacie,netspace_max_v2") ||
-	    of_machine_is_compatible("lacie,netspace_mini_v2") ||
-	    of_machine_is_compatible("lacie,netspace_v2"))
-		ns2_init();
-
-	if (of_machine_is_compatible("marvell,db-88f6281-bp") ||
-	    of_machine_is_compatible("marvell,db-88f6282-bp"))
-		db88f628x_init();
-
-	if (of_machine_is_compatible("mpl,cec4"))
-		mplcec4_init();
-
-	if (of_machine_is_compatible("netgear,readynas-duo-v2"))
-		netgear_readynas_init();
-
-	if (of_machine_is_compatible("plathome,openblocks-a6"))
-		openblocks_a6_init();
-
-	if (of_machine_is_compatible("usi,topkick"))
-		usi_topkick_init();
+	if (of_machine_is_compatible("marvell,mv88f6281gtw-ge"))
+		mv88f6281gtw_ge_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
 static const char * const kirkwood_dt_board_compat[] = {
-	"globalscale,dreamplug",
-	"globalscale,guruplug",
-	"globalscale,sheevaplug",
-	"dlink,dns-320",
-	"dlink,dns-325",
-	"iom,iconnect",
-	"raidsonic,ib-nas62x0",
-	"qnap,ts219",
-	"seagate,dockstar",
-	"seagate,goflexnet",
-	"buffalo,lsxl",
-	"iom,ix2-200",
-	"keymile,km_kirkwood",
-	"lacie,cloudbox",
-	"lacie,inetspace_v2",
-	"lacie,netspace_lite_v2",
-	"lacie,netspace_max_v2",
-	"lacie,netspace_mini_v2",
-	"lacie,netspace_v2",
-	"marvell,db-88f6281-bp",
-	"marvell,db-88f6282-bp",
-	"mpl,cec4",
-	"netgear,readynas-duo-v2",
-	"plathome,openblocks-a6",
-	"usi,topkick",
-	"zyxel,nsa310",
+	"marvell,kirkwood",
 	NULL
 };
 
 DT_MACHINE_START(KIRKWOOD_DT, "Marvell Kirkwood (Flattened Device Tree)")
 	/* Maintainer: Jason Cooper <jason@lakedaemon.net> */
 	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= orion_dt_init_irq,
-	.init_time	= kirkwood_timer_init,
+	.init_early	= kirkwood_dt_init_early,
+	.init_time	= kirkwood_dt_time_init,
 	.init_machine	= kirkwood_dt_init,
 	.restart	= kirkwood_restart,
 	.dt_compat	= kirkwood_dt_board_compat,
diff --git a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c
deleted file mode 100644
index 9db979a..0000000
--- a/arch/arm/mach-kirkwood/board-goflexnet.c
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-goflexnet.c
- *
- * Seagate GoFlext Net Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * Copied and modified for Seagate GoFlex Net support by
- * Joshua Coombs <josh.coombs@gmail.com> based on ArchLinux ARM's
- * GoFlex kernel patches.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data goflexnet_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init goflexnet_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&goflexnet_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-guruplug.c b/arch/arm/mach-kirkwood/board-guruplug.c
deleted file mode 100644
index a857163..0000000
--- a/arch/arm/mach-kirkwood/board-guruplug.c
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-guruplug.c
- *
- * Marvell Guruplug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data guruplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-void __init guruplug_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&guruplug_ge00_data);
-	kirkwood_ge01_init(&guruplug_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-ib62x0.c b/arch/arm/mach-kirkwood/board-ib62x0.c
deleted file mode 100644
index 9a857ae..0000000
--- a/arch/arm/mach-kirkwood/board-ib62x0.c
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * Copyright 2012 (C), Simon Baatz <gmbnomis@gmail.com>
- *
- * arch/arm/mach-kirkwood/board-ib62x0.c
- *
- * RaidSonic ICY BOX IB-NAS6210 & IB-NAS6220 init for drivers not
- * converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data ib62x0_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init ib62x0_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&ib62x0_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c
deleted file mode 100644
index 98b5ad1..0000000
--- a/arch/arm/mach-kirkwood/board-iconnect.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-iconnect.c
- *
- * Iomega i-connect Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data iconnect_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(11),
-};
-
-void __init iconnect_init(void)
-{
-	kirkwood_ge00_init(&iconnect_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
deleted file mode 100644
index e5f7041..0000000
--- a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-iomega_ix2_200.c
- *
- * Iomega StorCenter ix2-200
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/ethtool.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
-	.phy_addr       = MV643XX_ETH_PHY_NONE,
-	.speed          = SPEED_1000,
-	.duplex         = DUPLEX_FULL,
-};
-
-static struct mv643xx_eth_platform_data iomega_ix2_200_ge01_data = {
-        .phy_addr       = MV643XX_ETH_PHY_ADDR(11),
-};
-
-void __init iomega_ix2_200_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&iomega_ix2_200_ge00_data);
-	kirkwood_ge01_init(&iomega_ix2_200_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-km_kirkwood.c b/arch/arm/mach-kirkwood/board-km_kirkwood.c
deleted file mode 100644
index 44e4605..0000000
--- a/arch/arm/mach-kirkwood/board-km_kirkwood.c
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * Copyright 2012 2012 KEYMILE AG, CH-3097 Bern
- * Valentin Longchamp <valentin.longchamp@keymile.com>
- *
- * arch/arm/mach-kirkwood/board-km_kirkwood.c
- *
- * Keymile km_kirkwood Reference Desing Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/clk.h>
-#include <linux/clk-private.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data km_kirkwood_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init km_kirkwood_init(void)
-{
-	struct clk *sata_clk;
-	/*
-	 * Our variant of kirkwood (integrated in the Bobcat) hangs on accessing
-	 * SATA bits (14-15) of the Clock Gating Control Register. Since these
-	 * devices are also not present in this variant, their clocks get
-	 * disabled because unused when clk_disable_unused() gets called.
-	 * That's why we change the flags to these clocks to CLK_IGNORE_UNUSED
-	 */
-	sata_clk = clk_get_sys("sata_mv.0", "0");
-	if (!IS_ERR(sata_clk))
-		sata_clk->flags |= CLK_IGNORE_UNUSED;
-	sata_clk = clk_get_sys("sata_mv.0", "1");
-	if (!IS_ERR(sata_clk))
-		sata_clk->flags |= CLK_IGNORE_UNUSED;
-
-	kirkwood_ge00_init(&km_kirkwood_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-lsxl.c b/arch/arm/mach-kirkwood/board-lsxl.c
deleted file mode 100644
index 3483952..0000000
--- a/arch/arm/mach-kirkwood/board-lsxl.c
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * Copyright 2012 (C), Michael Walle <michael@walle.cc>
- *
- * arch/arm/mach-kirkwood/board-lsxl.c
- *
- * Buffalo Linkstation LS-XHL and LS-CHLv2 init for drivers not
- * converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data lsxl_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data lsxl_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init lsxl_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-
-	kirkwood_ge00_init(&lsxl_ge00_data);
-	kirkwood_ge01_init(&lsxl_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-mplcec4.c b/arch/arm/mach-kirkwood/board-mplcec4.c
deleted file mode 100644
index 938712e..0000000
--- a/arch/arm/mach-kirkwood/board-mplcec4.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright (C) 2012 MPL AG, Switzerland
- * Stefan Peter <s.peter@mpl.ch>
- *
- * arch/arm/mach-kirkwood/board-mplcec4.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data mplcec4_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-static struct mv643xx_eth_platform_data mplcec4_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(2),
-};
-
-void __init mplcec4_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&mplcec4_ge00_data);
-	kirkwood_ge01_init(&mplcec4_ge01_data);
-}
-
-
-
diff --git a/arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c b/arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
new file mode 100644
index 0000000..ee5eea6
--- /dev/null
+++ b/arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
@@ -0,0 +1,50 @@
+/*
+ * arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
+ *
+ * Marvell 88F6281 GTW GE Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/timer.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
+#include <linux/gpio.h>
+#include <net/dsa.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+
+static struct mv643xx_eth_platform_data mv88f6281gtw_ge_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_NONE,
+	.speed		= SPEED_1000,
+	.duplex		= DUPLEX_FULL,
+};
+
+static struct dsa_chip_data mv88f6281gtw_ge_switch_chip_data = {
+	.port_names[0]	= "lan1",
+	.port_names[1]	= "lan2",
+	.port_names[2]	= "lan3",
+	.port_names[3]	= "lan4",
+	.port_names[4]	= "wan",
+	.port_names[5]	= "cpu",
+};
+
+static struct dsa_platform_data mv88f6281gtw_ge_switch_plat_data = {
+	.nr_chips	= 1,
+	.chip		= &mv88f6281gtw_ge_switch_chip_data,
+};
+
+void __init mv88f6281gtw_ge_init(void)
+{
+	kirkwood_ge00_init(&mv88f6281gtw_ge_ge00_data);
+	kirkwood_ge00_switch_init(&mv88f6281gtw_ge_switch_plat_data, NO_IRQ);
+}
diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c
deleted file mode 100644
index f8f6605..0000000
--- a/arch/arm/mach-kirkwood/board-ns2.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright 2012 (C), Simon Guinot <simon.guinot@sequanux.org>
- *
- * arch/arm/mach-kirkwood/board-ns2.c
- *
- * LaCie Network Space v2 board (and parents) initialization for drivers
- * not converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/of.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data ns2_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init ns2_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	if (of_machine_is_compatible("lacie,cloudbox") ||
-	    of_machine_is_compatible("lacie,netspace_lite_v2") ||
-	    of_machine_is_compatible("lacie,netspace_mini_v2"))
-		ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
-	kirkwood_ge00_init(&ns2_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-openblocks_a6.c b/arch/arm/mach-kirkwood/board-openblocks_a6.c
deleted file mode 100644
index b11d8fd..0000000
--- a/arch/arm/mach-kirkwood/board-openblocks_a6.c
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * Copyright 2012 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- *
- * arch/arm/mach-kirkwood/board-openblocks_a6.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data openblocks_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init openblocks_a6_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&openblocks_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-readynas.c b/arch/arm/mach-kirkwood/board-readynas.c
deleted file mode 100644
index 341b82d..0000000
--- a/arch/arm/mach-kirkwood/board-readynas.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * NETGEAR ReadyNAS Duo v2 Board setup for drivers not already
- * converted to DT.
- *
- * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data netgear_readynas_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init netgear_readynas_init(void)
-{
-	kirkwood_ge00_init(&netgear_readynas_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-sheevaplug.c b/arch/arm/mach-kirkwood/board-sheevaplug.c
deleted file mode 100644
index fa38937..0000000
--- a/arch/arm/mach-kirkwood/board-sheevaplug.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-sheevaplug.c
- *
- * Marvell Sheevaplug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init sheevaplug_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&sheevaplug_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-ts219.c b/arch/arm/mach-kirkwood/board-ts219.c
deleted file mode 100644
index 860f44a..0000000
--- a/arch/arm/mach-kirkwood/board-ts219.c
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- *
- * QNAP TS-11x/TS-21x Turbo NAS Board Setup via DT
- *
- * Copyright (C) 2012 Andrew Lunn <andrew@lunn.ch>
- *
- * Based on the board file ts219-setup.c:
- *
- * Copyright (C) 2009  Martin Michlmayr <tbm@cyrius.com>
- * Copyright (C) 2008  Byron Bradley <byron.bbradley@gmail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init qnap_dt_ts219_init(void)
-{
-	u32 dev, rev;
-
-	kirkwood_pcie_id(&dev, &rev);
-	if (dev == MV88F6282_DEV_ID)
-		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
-
-	kirkwood_ge00_init(&qnap_ts219_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-usi_topkick.c b/arch/arm/mach-kirkwood/board-usi_topkick.c
deleted file mode 100644
index 1cc04ec..0000000
--- a/arch/arm/mach-kirkwood/board-usi_topkick.c
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-usi_topkick.c
- *
- * USI Topkick Init for drivers not converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data topkick_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init usi_topkick_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&topkick_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
index fcf3ba6..1296de9 100644
--- a/arch/arm/mach-kirkwood/common.h
+++ b/arch/arm/mach-kirkwood/common.h
@@ -59,119 +59,10 @@ void kirkwood_restart(enum reboot_mode, const char *);
 void kirkwood_clk_init(void);
 
 /* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_DREAMPLUG_DT
-void dreamplug_init(void);
+#ifdef CONFIG_MACH_MV88F6281GTW_GE_DT
+void mv88f6281gtw_ge_init(void);
 #else
-static inline void dreamplug_init(void) {};
-#endif
-#ifdef CONFIG_MACH_GURUPLUG_DT
-void guruplug_dt_init(void);
-#else
-static inline void guruplug_dt_init(void) {};
-#endif
-#ifdef CONFIG_MACH_SHEEVAPLUG_DT
-void sheevaplug_dt_init(void);
-#else
-static inline void sheevaplug_dt_init(void) {};
-#endif
-#ifdef CONFIG_MACH_TS219_DT
-void qnap_dt_ts219_init(void);
-#else
-static inline void qnap_dt_ts219_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
-void dnskw_init(void);
-#else
-static inline void dnskw_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_ICONNECT_DT
-void iconnect_init(void);
-#else
-static inline void iconnect_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_IB62X0_DT
-void ib62x0_init(void);
-#else
-static inline void ib62x0_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DOCKSTAR_DT
-void dockstar_dt_init(void);
-#else
-static inline void dockstar_dt_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_GOFLEXNET_DT
-void goflexnet_init(void);
-#else
-static inline void goflexnet_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_LSXL_DT
-void lsxl_init(void);
-#else
-static inline void lsxl_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
-void iomega_ix2_200_init(void);
-#else
-static inline void iomega_ix2_200_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_KM_KIRKWOOD_DT
-void km_kirkwood_init(void);
-#else
-static inline void km_kirkwood_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DB88F628X_BP_DT
-void db88f628x_init(void);
-#else
-static inline void db88f628x_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_MPLCEC4_DT
-void mplcec4_init(void);
-#else
-static inline void mplcec4_init(void) {};
-#endif
-
-#if defined(CONFIG_MACH_INETSPACE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_MAX_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_LITE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_MINI_V2_DT)
-void ns2_init(void);
-#else
-static inline void ns2_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_OPENBLOCKS_A6_DT
-void openblocks_a6_init(void);
-#else
-static inline void openblocks_a6_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_READYNAS_DT
-void netgear_readynas_init(void);
-#else
-static inline void netgear_readynas_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_TOPKICK_DT
-void usi_topkick_init(void);
-#else
-static inline void usi_topkick_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_CLOUDBOX_DT
-void cloudbox_init(void);
-#else
-static inline void cloudbox_init(void) {};
+static inline void mv88f6281gtw_ge_init(void) {};
 #endif
 
 /* early init functions not converted to fdt yet */
diff --git a/arch/arm/mach-kirkwood/dockstar-setup.c b/arch/arm/mach-kirkwood/dockstar-setup.c
deleted file mode 100644
index 060ccf9..0000000
--- a/arch/arm/mach-kirkwood/dockstar-setup.c
+++ /dev/null
@@ -1,111 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/dockstar-setup.c
- *
- * Seagate FreeAgent DockStar Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mtd_partition dockstar_nand_parts[] = {
-	{
-		.name = "u-boot",
-		.offset = 0,
-		.size = SZ_1M
-	}, {
-		.name = "uImage",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size = SZ_4M
-	}, {
-		.name = "root",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size = MTDPART_SIZ_FULL
-	},
-};
-
-static struct mv643xx_eth_platform_data dockstar_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct gpio_led dockstar_led_pins[] = {
-	{
-		.name			= "dockstar:green:health",
-		.default_trigger	= "default-on",
-		.gpio			= 46,
-		.active_low		= 1,
-	},
-	{
-		.name			= "dockstar:orange:misc",
-		.default_trigger	= "none",
-		.gpio			= 47,
-		.active_low		= 1,
-	},
-};
-
-static struct gpio_led_platform_data dockstar_led_data = {
-	.leds		= dockstar_led_pins,
-	.num_leds	= ARRAY_SIZE(dockstar_led_pins),
-};
-
-static struct platform_device dockstar_leds = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &dockstar_led_data,
-	}
-};
-
-static unsigned int dockstar_mpp_config[] __initdata = {
-	MPP29_GPIO,	/* USB Power Enable */
-	MPP46_GPIO,	/* LED green */
-	MPP47_GPIO,	/* LED orange */
-	0
-};
-
-static void __init dockstar_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_init();
-
-	/* setup gpio pin select */
-	kirkwood_mpp_conf(dockstar_mpp_config);
-
-	kirkwood_uart0_init();
-	kirkwood_nand_init(ARRAY_AND_SIZE(dockstar_nand_parts), 25);
-
-	if (gpio_request(29, "USB Power Enable") != 0 ||
-	    gpio_direction_output(29, 1) != 0)
-		pr_err("can't set up GPIO 29 (USB Power Enable)\n");
-	kirkwood_ehci_init();
-
-	kirkwood_ge00_init(&dockstar_ge00_data);
-
-	platform_device_register(&dockstar_leds);
-}
-
-MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar")
-	.atag_offset	= 0x100,
-	.init_machine	= dockstar_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c
deleted file mode 100644
index 08dd739..0000000
--- a/arch/arm/mach-kirkwood/guruplug-setup.c
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/guruplug-setup.c
- *
- * Marvell GuruPlug Reference Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/partitions.h>
-#include <linux/ata_platform.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include <linux/platform_data/mmc-mvsdio.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mtd_partition guruplug_nand_parts[] = {
-	{
-		.name = "u-boot",
-		.offset = 0,
-		.size = SZ_1M
-	}, {
-		.name = "uImage",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size = SZ_4M
-	}, {
-		.name = "root",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size = MTDPART_SIZ_FULL
-	},
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-static struct mv_sata_platform_data guruplug_sata_data = {
-	.n_ports	= 1,
-};
-
-static struct mvsdio_platform_data guruplug_mvsdio_data = {
-	/* unfortunately the CD signal has not been connected */
-	.gpio_card_detect = -1,
-	.gpio_write_protect = -1,
-};
-
-static struct gpio_led guruplug_led_pins[] = {
-	{
-		.name			= "guruplug:red:health",
-		.gpio			= 46,
-		.active_low		= 1,
-	},
-	{
-		.name			= "guruplug:green:health",
-		.gpio			= 47,
-		.active_low		= 1,
-	},
-	{
-		.name			= "guruplug:red:wmode",
-		.gpio			= 48,
-		.active_low		= 1,
-	},
-	{
-		.name			= "guruplug:green:wmode",
-		.gpio			= 49,
-		.active_low		= 1,
-	},
-};
-
-static struct gpio_led_platform_data guruplug_led_data = {
-	.leds		= guruplug_led_pins,
-	.num_leds	= ARRAY_SIZE(guruplug_led_pins),
-};
-
-static struct platform_device guruplug_leds = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &guruplug_led_data,
-	}
-};
-
-static unsigned int guruplug_mpp_config[] __initdata = {
-	MPP46_GPIO,	/* M_RLED */
-	MPP47_GPIO,	/* M_GLED */
-	MPP48_GPIO,	/* B_RLED */
-	MPP49_GPIO,	/* B_GLED */
-	0
-};
-
-static void __init guruplug_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_init();
-	kirkwood_mpp_conf(guruplug_mpp_config);
-
-	kirkwood_uart0_init();
-	kirkwood_nand_init(ARRAY_AND_SIZE(guruplug_nand_parts), 25);
-
-	kirkwood_ehci_init();
-	kirkwood_ge00_init(&guruplug_ge00_data);
-	kirkwood_ge01_init(&guruplug_ge01_data);
-	kirkwood_sata_init(&guruplug_sata_data);
-	kirkwood_sdio_init(&guruplug_mvsdio_data);
-
-	platform_device_register(&guruplug_leds);
-}
-
-MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
-	/* Maintainer: Siddarth Gore <gores@marvell.com> */
-	.atag_offset	= 0x100,
-	.init_machine	= guruplug_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
diff --git a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c b/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
deleted file mode 100644
index ba384b9..0000000
--- a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
+++ /dev/null
@@ -1,172 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
- *
- * Marvell 88F6281 GTW GE Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/timer.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/ethtool.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <net/dsa.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mv643xx_eth_platform_data mv88f6281gtw_ge_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_NONE,
-	.speed		= SPEED_1000,
-	.duplex		= DUPLEX_FULL,
-};
-
-static struct dsa_chip_data mv88f6281gtw_ge_switch_chip_data = {
-	.port_names[0]	= "lan1",
-	.port_names[1]	= "lan2",
-	.port_names[2]	= "lan3",
-	.port_names[3]	= "lan4",
-	.port_names[4]	= "wan",
-	.port_names[5]	= "cpu",
-};
-
-static struct dsa_platform_data mv88f6281gtw_ge_switch_plat_data = {
-	.nr_chips	= 1,
-	.chip		= &mv88f6281gtw_ge_switch_chip_data,
-};
-
-static const struct flash_platform_data mv88f6281gtw_ge_spi_slave_data = {
-	.type		= "mx25l12805d",
-};
-
-static struct spi_board_info __initdata mv88f6281gtw_ge_spi_slave_info[] = {
-	{
-		.modalias	= "m25p80",
-		.platform_data	= &mv88f6281gtw_ge_spi_slave_data,
-		.irq		= -1,
-		.max_speed_hz	= 50000000,
-		.bus_num	= 0,
-		.chip_select	= 0,
-	},
-};
-
-static struct gpio_keys_button mv88f6281gtw_ge_button_pins[] = {
-	{
-		.code		= KEY_RESTART,
-		.gpio		= 47,
-		.desc		= "SWR Button",
-		.active_low	= 1,
-	}, {
-		.code		= KEY_WPS_BUTTON,
-		.gpio		= 46,
-		.desc		= "WPS Button",
-		.active_low	= 1,
-	},
-};
-
-static struct gpio_keys_platform_data mv88f6281gtw_ge_button_data = {
-	.buttons	= mv88f6281gtw_ge_button_pins,
-	.nbuttons	= ARRAY_SIZE(mv88f6281gtw_ge_button_pins),
-};
-
-static struct platform_device mv88f6281gtw_ge_buttons = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &mv88f6281gtw_ge_button_data,
-	},
-};
-
-static struct gpio_led mv88f6281gtw_ge_led_pins[] = {
-	{
-		.name		= "gtw:green:Status",
-		.gpio		= 20,
-		.active_low	= 0,
-	}, {
-		.name		= "gtw:red:Status",
-		.gpio		= 21,
-		.active_low	= 0,
-	}, {
-		.name		= "gtw:green:USB",
-		.gpio		= 12,
-		.active_low	= 0,
-	},
-};
-
-static struct gpio_led_platform_data mv88f6281gtw_ge_led_data = {
-	.leds		= mv88f6281gtw_ge_led_pins,
-	.num_leds	= ARRAY_SIZE(mv88f6281gtw_ge_led_pins),
-};
-
-static struct platform_device mv88f6281gtw_ge_leds = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &mv88f6281gtw_ge_led_data,
-	},
-};
-
-static unsigned int mv88f6281gtw_ge_mpp_config[] __initdata = {
-	MPP12_GPO,	/* Status#_USB pin  */
-	MPP20_GPIO,	/* Status#_GLED pin */
-	MPP21_GPIO,	/* Status#_RLED pin */
-	MPP46_GPIO,	/* WPS_Switch pin   */
-	MPP47_GPIO,	/* SW_Init pin      */
-	0
-};
-
-static void __init mv88f6281gtw_ge_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_init();
-	kirkwood_mpp_conf(mv88f6281gtw_ge_mpp_config);
-
-	kirkwood_ehci_init();
-	kirkwood_ge00_init(&mv88f6281gtw_ge_ge00_data);
-	kirkwood_ge00_switch_init(&mv88f6281gtw_ge_switch_plat_data, NO_IRQ);
-	spi_register_board_info(mv88f6281gtw_ge_spi_slave_info,
-				ARRAY_SIZE(mv88f6281gtw_ge_spi_slave_info));
-	kirkwood_spi_init();
-	kirkwood_uart0_init();
-	platform_device_register(&mv88f6281gtw_ge_leds);
-	platform_device_register(&mv88f6281gtw_ge_buttons);
-}
-
-static int __init mv88f6281gtw_ge_pci_init(void)
-{
-	if (machine_is_mv88f6281gtw_ge())
-		kirkwood_pcie_init(KW_PCIE0);
-
-	return 0;
-}
-subsys_initcall(mv88f6281gtw_ge_pci_init);
-
-MACHINE_START(MV88F6281GTW_GE, "Marvell 88F6281 GTW GE Board")
-	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.atag_offset	= 0x100,
-	.init_machine	= mv88f6281gtw_ge_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
diff --git a/arch/arm/mach-kirkwood/netspace_v2-setup.c b/arch/arm/mach-kirkwood/netspace_v2-setup.c
deleted file mode 100644
index 3b70661..0000000
--- a/arch/arm/mach-kirkwood/netspace_v2-setup.c
+++ /dev/null
@@ -1,293 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/netspace_v2-setup.c
- *
- * LaCie Network Space v2 board setup
- *
- * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- * Copyright (C) 2009 Benoît Canet <benoit.canet@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/leds.h>
-#include <linux/gpio-fan.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include <linux/platform_data/leds-kirkwood-ns2.h>
-#include "common.h"
-#include "mpp.h"
-#include "lacie_v2-common.h"
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data netspace_v2_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data netspace_v2_sata_data = {
-	.n_ports	= 2,
-};
-
-/*****************************************************************************
- * GPIO keys
- ****************************************************************************/
-
-#define NETSPACE_V2_PUSH_BUTTON		32
-
-static struct gpio_keys_button netspace_v2_buttons[] = {
-	[0] = {
-		.code		= KEY_POWER,
-		.gpio		= NETSPACE_V2_PUSH_BUTTON,
-		.desc		= "Power push button",
-		.active_low	= 0,
-	},
-};
-
-static struct gpio_keys_platform_data netspace_v2_button_data = {
-	.buttons	= netspace_v2_buttons,
-	.nbuttons	= ARRAY_SIZE(netspace_v2_buttons),
-};
-
-static struct platform_device netspace_v2_gpio_buttons = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &netspace_v2_button_data,
-	},
-};
-
-/*****************************************************************************
- * GPIO LEDs
- ****************************************************************************/
-
-#define NETSPACE_V2_GPIO_RED_LED	12
-
-static struct gpio_led netspace_v2_gpio_led_pins[] = {
-	{
-		.name	= "ns_v2:red:fail",
-		.gpio	= NETSPACE_V2_GPIO_RED_LED,
-	},
-};
-
-static struct gpio_led_platform_data netspace_v2_gpio_leds_data = {
-	.num_leds	= ARRAY_SIZE(netspace_v2_gpio_led_pins),
-	.leds		= netspace_v2_gpio_led_pins,
-};
-
-static struct platform_device netspace_v2_gpio_leds = {
-	.name		= "leds-gpio",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &netspace_v2_gpio_leds_data,
-	},
-};
-
-/*****************************************************************************
- * Dual-GPIO CPLD LEDs
- ****************************************************************************/
-
-#define NETSPACE_V2_GPIO_BLUE_LED_SLOW	29
-#define NETSPACE_V2_GPIO_BLUE_LED_CMD	30
-
-static struct ns2_led netspace_v2_led_pins[] = {
-	{
-		.name	= "ns_v2:blue:sata",
-		.cmd	= NETSPACE_V2_GPIO_BLUE_LED_CMD,
-		.slow	= NETSPACE_V2_GPIO_BLUE_LED_SLOW,
-	},
-};
-
-static struct ns2_led_platform_data netspace_v2_leds_data = {
-	.num_leds	= ARRAY_SIZE(netspace_v2_led_pins),
-	.leds		= netspace_v2_led_pins,
-};
-
-static struct platform_device netspace_v2_leds = {
-	.name		= "leds-ns2",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &netspace_v2_leds_data,
-	},
-};
-
-/*****************************************************************************
- * GPIO fan
- ****************************************************************************/
-
-/* Designed for fan 40x40x16: ADDA AD0412LB-D50 6000rpm@12v */
-static struct gpio_fan_speed netspace_max_v2_fan_speed[] = {
-	{    0,  0 },
-	{ 1500,	15 },
-	{ 1700,	14 },
-	{ 1800,	13 },
-	{ 2100,	12 },
-	{ 3100,	11 },
-	{ 3300,	10 },
-	{ 4300,	 9 },
-	{ 5500,	 8 },
-};
-
-static unsigned netspace_max_v2_fan_ctrl[] = { 22, 7, 33, 23 };
-
-static struct gpio_fan_alarm netspace_max_v2_fan_alarm = {
-	.gpio		= 25,
-	.active_low	= 1,
-};
-
-static struct gpio_fan_platform_data netspace_max_v2_fan_data = {
-	.num_ctrl	= ARRAY_SIZE(netspace_max_v2_fan_ctrl),
-	.ctrl		= netspace_max_v2_fan_ctrl,
-	.alarm		= &netspace_max_v2_fan_alarm,
-	.num_speed	= ARRAY_SIZE(netspace_max_v2_fan_speed),
-	.speed		= netspace_max_v2_fan_speed,
-};
-
-static struct platform_device netspace_max_v2_gpio_fan = {
-	.name	= "gpio-fan",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &netspace_max_v2_fan_data,
-	},
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-
-static unsigned int netspace_v2_mpp_config[] __initdata = {
-	MPP0_SPI_SCn,
-	MPP1_SPI_MOSI,
-	MPP2_SPI_SCK,
-	MPP3_SPI_MISO,
-	MPP4_NF_IO6,
-	MPP5_NF_IO7,
-	MPP6_SYSRST_OUTn,
-	MPP7_GPO,		/* Fan speed (bit 1) */
-	MPP8_TW0_SDA,
-	MPP9_TW0_SCK,
-	MPP10_UART0_TXD,
-	MPP11_UART0_RXD,
-	MPP12_GPO,		/* Red led */
-	MPP14_GPIO,		/* USB fuse */
-	MPP16_GPIO,		/* SATA 0 power */
-	MPP17_GPIO,		/* SATA 1 power */
-	MPP18_NF_IO0,
-	MPP19_NF_IO1,
-	MPP20_SATA1_ACTn,
-	MPP21_SATA0_ACTn,
-	MPP22_GPIO,		/* Fan speed (bit 0) */
-	MPP23_GPIO,		/* Fan power */
-	MPP24_GPIO,		/* USB mode select */
-	MPP25_GPIO,		/* Fan rotation fail */
-	MPP26_GPIO,		/* USB device vbus */
-	MPP28_GPIO,		/* USB enable host vbus */
-	MPP29_GPIO,		/* Blue led (slow register) */
-	MPP30_GPIO,		/* Blue led (command register) */
-	MPP31_GPIO,		/* Board power off */
-	MPP32_GPIO,		/* Power button (0 = Released, 1 = Pushed) */
-	MPP33_GPO,		/* Fan speed (bit 2) */
-	0
-};
-
-#define NETSPACE_V2_GPIO_POWER_OFF	31
-
-static void netspace_v2_power_off(void)
-{
-	gpio_set_value(NETSPACE_V2_GPIO_POWER_OFF, 1);
-}
-
-static void __init netspace_v2_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_init();
-	kirkwood_mpp_conf(netspace_v2_mpp_config);
-
-	if (machine_is_netspace_max_v2())
-		lacie_v2_hdd_power_init(2);
-	else
-		lacie_v2_hdd_power_init(1);
-
-	kirkwood_ehci_init();
-	kirkwood_ge00_init(&netspace_v2_ge00_data);
-	kirkwood_sata_init(&netspace_v2_sata_data);
-	kirkwood_uart0_init();
-	lacie_v2_register_flash();
-	lacie_v2_register_i2c_devices();
-
-	platform_device_register(&netspace_v2_leds);
-	platform_device_register(&netspace_v2_gpio_leds);
-	platform_device_register(&netspace_v2_gpio_buttons);
-	if (machine_is_netspace_max_v2())
-		platform_device_register(&netspace_max_v2_gpio_fan);
-
-	if (gpio_request(NETSPACE_V2_GPIO_POWER_OFF, "power-off") == 0 &&
-	    gpio_direction_output(NETSPACE_V2_GPIO_POWER_OFF, 0) == 0)
-		pm_power_off = netspace_v2_power_off;
-	else
-		pr_err("netspace_v2: failed to configure power-off GPIO\n");
-}
-
-#ifdef CONFIG_MACH_NETSPACE_V2
-MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
-	.atag_offset	= 0x100,
-	.init_machine	= netspace_v2_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_INETSPACE_V2
-MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
-	.atag_offset	= 0x100,
-	.init_machine	= netspace_v2_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_NETSPACE_MAX_V2
-MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
-	.atag_offset	= 0x100,
-	.init_machine	= netspace_v2_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
-#endif
diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c
index 6a6eb54..e5cf841 100644
--- a/arch/arm/mach-kirkwood/openrd-setup.c
+++ b/arch/arm/mach-kirkwood/openrd-setup.c
@@ -158,7 +158,8 @@ static void __init openrd_init(void)
 	kirkwood_mpp_conf(openrd_mpp_config);
 
 	kirkwood_uart0_init();
-	kirkwood_nand_init(ARRAY_AND_SIZE(openrd_nand_parts), 25);
+	kirkwood_nand_init(openrd_nand_parts, ARRAY_SIZE(openrd_nand_parts),
+			   25);
 
 	kirkwood_ehci_init();
 
diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c
index d242231..5154bd2 100644
--- a/arch/arm/mach-kirkwood/rd88f6281-setup.c
+++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c
@@ -87,7 +87,9 @@ static void __init rd88f6281_init(void)
 	kirkwood_init();
 	kirkwood_mpp_conf(rd88f6281_mpp_config);
 
-	kirkwood_nand_init(ARRAY_AND_SIZE(rd88f6281_nand_parts), 25);
+	kirkwood_nand_init(rd88f6281_nand_parts,
+			   ARRAY_SIZE(rd88f6281_nand_parts),
+			   25);
 	kirkwood_ehci_init();
 
 	kirkwood_ge00_init(&rd88f6281_ge00_data);
diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c
deleted file mode 100644
index 55b68fa..0000000
--- a/arch/arm/mach-kirkwood/sheevaplug-setup.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/sheevaplug-setup.c
- *
- * Marvell SheevaPlug Reference Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include <linux/platform_data/mmc-mvsdio.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mtd_partition sheevaplug_nand_parts[] = {
-	{
-		.name = "u-boot",
-		.offset = 0,
-		.size = SZ_1M
-	}, {
-		.name = "uImage",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size = SZ_4M
-	}, {
-		.name = "root",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size = MTDPART_SIZ_FULL
-	},
-};
-
-static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv_sata_platform_data sheeva_esata_sata_data = {
-	.n_ports	= 2,
-};
-
-static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
-	/* unfortunately the CD signal has not been connected */
-};
-
-static struct mvsdio_platform_data sheeva_esata_mvsdio_data = {
-	.gpio_write_protect = 44, /* MPP44 used as SD write protect */
-	.gpio_card_detect = 47,	  /* MPP47 used as SD card detect */
-};
-
-static struct gpio_led sheevaplug_led_pins[] = {
-	{
-		.name			= "plug:red:misc",
-		.default_trigger	= "none",
-		.gpio			= 46,
-		.active_low		= 1,
-	},
-	{
-		.name			= "plug:green:health",
-		.default_trigger	= "default-on",
-		.gpio			= 49,
-		.active_low		= 1,
-	},
-};
-
-static struct gpio_led_platform_data sheevaplug_led_data = {
-	.leds		= sheevaplug_led_pins,
-	.num_leds	= ARRAY_SIZE(sheevaplug_led_pins),
-};
-
-static struct platform_device sheevaplug_leds = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &sheevaplug_led_data,
-	}
-};
-
-static unsigned int sheevaplug_mpp_config[] __initdata = {
-	MPP29_GPIO,	/* USB Power Enable */
-	MPP46_GPIO,	/* LED Red */
-	MPP49_GPIO,	/* LED */
-	0
-};
-
-static unsigned int sheeva_esata_mpp_config[] __initdata = {
-	MPP29_GPIO,	/* USB Power Enable */
-	MPP44_GPIO,	/* SD Write Protect */
-	MPP47_GPIO,	/* SD Card Detect */
-	MPP49_GPIO,	/* LED Green */
-	0
-};
-
-static void __init sheevaplug_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_init();
-
-	/* setup gpio pin select */
-	if (machine_is_esata_sheevaplug())
-		kirkwood_mpp_conf(sheeva_esata_mpp_config);
-	else
-		kirkwood_mpp_conf(sheevaplug_mpp_config);
-
-	kirkwood_uart0_init();
-	kirkwood_nand_init(ARRAY_AND_SIZE(sheevaplug_nand_parts), 25);
-
-	if (gpio_request(29, "USB Power Enable") != 0 ||
-	    gpio_direction_output(29, 1) != 0)
-		pr_err("can't set up GPIO 29 (USB Power Enable)\n");
-	kirkwood_ehci_init();
-
-	kirkwood_ge00_init(&sheevaplug_ge00_data);
-
-	/* honor lower power consumption for plugs with out eSATA */
-	if (machine_is_esata_sheevaplug())
-		kirkwood_sata_init(&sheeva_esata_sata_data);
-
-	/* enable sd wp and sd cd on plugs with esata */
-	if (machine_is_esata_sheevaplug())
-		kirkwood_sdio_init(&sheeva_esata_mvsdio_data);
-	else
-		kirkwood_sdio_init(&sheevaplug_mvsdio_data);
-
-	platform_device_register(&sheevaplug_leds);
-}
-
-#ifdef CONFIG_MACH_SHEEVAPLUG
-MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
-	/* Maintainer: shadi Ammouri <shadi@marvell.com> */
-	.atag_offset	= 0x100,
-	.init_machine	= sheevaplug_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_ESATA_SHEEVAPLUG
-MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
-	.atag_offset	= 0x100,
-	.init_machine	= sheevaplug_init,
-	.map_io		= kirkwood_map_io,
-	.init_early	= kirkwood_init_early,
-	.init_irq	= kirkwood_init_irq,
-	.init_time	= kirkwood_timer_init,
-	.restart	= kirkwood_restart,
-MACHINE_END
-#endif
diff --git a/arch/arm/mach-orion5x/edmini_v2-setup.c b/arch/arm/mach-orion5x/edmini_v2-setup.c
index 0fc33c5..f66c1b2 100644
--- a/arch/arm/mach-orion5x/edmini_v2-setup.c
+++ b/arch/arm/mach-orion5x/edmini_v2-setup.c
@@ -23,8 +23,8 @@
 #include <linux/platform_device.h>
 #include <linux/pci.h>
 #include <linux/irq.h>
+#include <linux/mbus.h>
 #include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
 #include <linux/leds.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
@@ -96,14 +96,6 @@ static struct platform_device edmini_v2_nor_flash = {
 };
 
 /*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data edmini_v2_eth_data = {
-	.phy_addr	= 8,
-};
-
-/*****************************************************************************
  * RTC 5C372a on I2C bus
  ****************************************************************************/
 
@@ -152,7 +144,6 @@ void __init edmini_v2_init(void)
 	 * Configure peripherals.
 	 */
 	orion5x_ehci0_init();
-	orion5x_eth_init(&edmini_v2_eth_data);
 
 	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
 				    ORION_MBUS_DEVBUS_BOOT_ATTR,
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 403c939..e817fde 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -162,6 +162,7 @@ config MACH_BOCKW
 	depends on ARCH_R8A7778
 	select ARCH_REQUIRE_GPIOLIB
 	select RENESAS_INTC_IRQPIN
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	select USE_OF
 
 config MACH_MARZEN
diff --git a/arch/arm/mach-shmobile/board-ag5evm.c b/arch/arm/mach-shmobile/board-ag5evm.c
index c754071..f6d6449 100644
--- a/arch/arm/mach-shmobile/board-ag5evm.c
+++ b/arch/arm/mach-shmobile/board-ag5evm.c
@@ -41,6 +41,7 @@
 #include <linux/mmc/sh_mmcif.h>
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/mfd/tmio.h>
+#include <linux/platform_data/bd6107.h>
 #include <linux/sh_clk.h>
 #include <linux/irqchip/arm-gic.h>
 #include <video/sh_mobile_lcdc.h>
@@ -291,47 +292,7 @@ static struct platform_device mipidsi0_device = {
 	},
 };
 
-static unsigned char lcd_backlight_seq[3][2] = {
-	{ 0x04, 0x07 },
-	{ 0x23, 0x80 },
-	{ 0x03, 0x01 },
-};
-
-static int lcd_backlight_set_brightness(int brightness)
-{
-	struct i2c_adapter *adap;
-	struct i2c_msg msg;
-	unsigned int i;
-	int ret;
-
-	if (brightness == 0) {
-		/* Reset the chip */
-		gpio_set_value(235, 0);
-		mdelay(24);
-		gpio_set_value(235, 1);
-		return 0;
-	}
-
-	adap = i2c_get_adapter(1);
-	if (adap == NULL)
-		return -ENODEV;
-
-	for (i = 0; i < ARRAY_SIZE(lcd_backlight_seq); i++) {
-		msg.addr = 0x6d;
-		msg.buf = &lcd_backlight_seq[i][0];
-		msg.len = 2;
-		msg.flags = 0;
-
-		ret = i2c_transfer(adap, &msg, 1);
-		if (ret < 0)
-			break;
-	}
-
-	i2c_put_adapter(adap);
-	return ret < 0 ? ret : 0;
-}
-
-/* LCDC0 */
+/* LCDC0 and backlight */
 static const struct fb_videomode lcdc0_modes[] = {
 	{
 		.name		= "R63302(QHD)",
@@ -361,11 +322,6 @@ static struct sh_mobile_lcdc_info lcdc0_info = {
 			.width = 44,
 			.height = 79,
 		},
-		.bl_info = {
-			.name = "sh_mobile_lcdc_bl",
-			.max_brightness = 1,
-			.set_brightness = lcd_backlight_set_brightness,
-		},
 		.tx_dev = &mipidsi0_device,
 	}
 };
@@ -394,6 +350,17 @@ static struct platform_device lcdc0_device = {
 	},
 };
 
+static struct bd6107_platform_data backlight_data = {
+	.fbdev = &lcdc0_device.dev,
+	.reset = 235,
+	.def_value = 0,
+};
+
+static struct i2c_board_info backlight_board_info = {
+	I2C_BOARD_INFO("bd6107", 0x6d),
+	.platform_data = &backlight_data,
+};
+
 /* Fixed 2.8V regulators to be used by SDHI0 */
 static struct regulator_consumer_supply fixed2v8_power_consumers[] =
 {
@@ -648,15 +615,15 @@ static void __init ag5evm_init(void)
 	gpio_set_value(217, 1);
 	mdelay(100);
 
-	/* LCD backlight controller */
-	gpio_request_one(235, GPIOF_OUT_INIT_LOW, NULL); /* RESET */
-	lcd_backlight_set_brightness(0);
 
 #ifdef CONFIG_CACHE_L2X0
 	/* Shared attribute override enable, 64K*8way */
 	l2x0_init(IOMEM(0xf0100000), 0x00460000, 0xc2000fff);
 #endif
 	sh73a0_add_standard_devices();
+
+	i2c_register_board_info(1, &backlight_board_info, 1);
+
 	platform_add_devices(ag5evm_devices, ARRAY_SIZE(ag5evm_devices));
 }
 
diff --git a/arch/arm/mach-shmobile/board-ape6evm.c b/arch/arm/mach-shmobile/board-ape6evm.c
index af6dd39..38c6c73 100644
--- a/arch/arm/mach-shmobile/board-ape6evm.c
+++ b/arch/arm/mach-shmobile/board-ape6evm.c
@@ -19,8 +19,14 @@
  */
 
 #include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
+#include <linux/mfd/tmio.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/sh_mmcif.h>
+#include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/fixed.h>
@@ -33,6 +39,58 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
+/* LEDS */
+static struct gpio_led ape6evm_leds[] = {
+	{
+		.name		= "gnss-en",
+		.gpio		= 28,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	}, {
+		.name		= "nfc-nrst",
+		.gpio		= 126,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	}, {
+		.name		= "gnss-nrst",
+		.gpio		= 132,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	}, {
+		.name		= "bt-wakeup",
+		.gpio		= 232,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	}, {
+		.name		= "strobe",
+		.gpio		= 250,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	}, {
+		.name		= "bbresetout",
+		.gpio		= 288,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	},
+};
+
+static __initdata struct gpio_led_platform_data ape6evm_leds_pdata = {
+	.leds		= ape6evm_leds,
+	.num_leds	= ARRAY_SIZE(ape6evm_leds),
+};
+
+/* GPIO KEY */
+#define GPIO_KEY(c, g, d, ...) \
+	{ .code = c, .gpio = g, .desc = d, .active_low = 1 }
+
+static struct gpio_keys_button gpio_buttons[] = {
+	GPIO_KEY(KEY_0,			324,	"S16"),
+	GPIO_KEY(KEY_MENU,		325,	"S17"),
+	GPIO_KEY(KEY_HOME,		326,	"S18"),
+	GPIO_KEY(KEY_BACK,		327,	"S19"),
+	GPIO_KEY(KEY_VOLUMEUP,		328,	"S20"),
+	GPIO_KEY(KEY_VOLUMEDOWN,	329,	"S21"),
+};
+
+static struct __initdata gpio_keys_platform_data ape6evm_keys_pdata = {
+	.buttons	= gpio_buttons,
+	.nbuttons	= ARRAY_SIZE(gpio_buttons),
+};
+
 /* Dummy supplies, where voltage doesn't matter */
 static struct regulator_consumer_supply dummy_supplies[] = {
 	REGULATOR_SUPPLY("vddvario", "smsc911x"),
@@ -40,7 +98,7 @@ static struct regulator_consumer_supply dummy_supplies[] = {
 };
 
 /* SMSC LAN9220 */
-static const struct resource lan9220_res[] = {
+static const struct resource lan9220_res[] __initconst = {
 	DEFINE_RES_MEM(0x08000000, 0x1000),
 	{
 		.start	= irq_pin(40), /* IRQ40 */
@@ -48,19 +106,83 @@ static const struct resource lan9220_res[] = {
 	},
 };
 
-static const struct smsc911x_platform_config lan9220_data = {
+static const struct smsc911x_platform_config lan9220_data __initconst = {
 	.flags		= SMSC911X_USE_32BIT,
 	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
 	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
 };
 
-static const struct pinctrl_map ape6evm_pinctrl_map[] = {
+/*
+ * On APE6EVM power is supplied to MMCIF by a tps80032 regulator. For now we
+ * model a VDD supply to MMCIF, using a fixed 3.3V regulator. Also use the
+ * static power supply for SDHI0 and SDHI1, whereas SDHI0's VccQ is also
+ * supplied by the same tps80032 regulator and thus can also be adjusted
+ * dynamically.
+ */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+};
+
+/* MMCIF */
+static const struct sh_mmcif_plat_data mmcif0_pdata __initconst = {
+	.caps		= MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+};
+
+static const struct resource mmcif0_resources[] __initconst = {
+	DEFINE_RES_MEM_NAMED(0xee200000, 0x100, "MMCIF0"),
+	DEFINE_RES_IRQ(gic_spi(169)),
+};
+
+/* SDHI0 */
+static const struct sh_mobile_sdhi_info sdhi0_pdata __initconst = {
+	.tmio_flags	= TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_WRPROTECT_DISABLE,
+	.tmio_caps	= MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ,
+};
+
+static const struct resource sdhi0_resources[] __initconst = {
+	DEFINE_RES_MEM_NAMED(0xee100000, 0x100, "SDHI0"),
+	DEFINE_RES_IRQ(gic_spi(165)),
+};
+
+/* SDHI1 */
+static const struct sh_mobile_sdhi_info sdhi1_pdata __initconst = {
+	.tmio_flags	= TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_WRPROTECT_DISABLE,
+	.tmio_caps	= MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
+			  MMC_CAP_NEEDS_POLL,
+};
+
+static const struct resource sdhi1_resources[] __initconst = {
+	DEFINE_RES_MEM_NAMED(0xee120000, 0x100, "SDHI1"),
+	DEFINE_RES_IRQ(gic_spi(166)),
+};
+
+static const struct pinctrl_map ape6evm_pinctrl_map[] __initconst = {
 	/* SCIFA0 console */
 	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a73a4",
 				  "scifa0_data", "scifa0"),
 	/* SMSC */
 	PIN_MAP_MUX_GROUP_DEFAULT("smsc911x", "pfc-r8a73a4",
 				  "irqc_irq40", "irqc"),
+	/* MMCIF0 */
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a73a4",
+				  "mmc0_data8", "mmc0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a73a4",
+				  "mmc0_ctrl", "mmc0"),
+	/* SDHI0: uSD: no WP */
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a73a4",
+				  "sdhi0_data4", "sdhi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a73a4",
+				  "sdhi0_ctrl", "sdhi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a73a4",
+				  "sdhi0_cd", "sdhi0"),
+	/* SDHI1 */
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a73a4",
+				  "sdhi1_data4", "sdhi1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a73a4",
+				  "sdhi1_ctrl", "sdhi1"),
 };
 
 static void __init ape6evm_add_standard_devices(void)
@@ -93,6 +215,23 @@ static void __init ape6evm_add_standard_devices(void)
 	platform_device_register_resndata(&platform_bus, "smsc911x", -1,
 					  lan9220_res, ARRAY_SIZE(lan9220_res),
 					  &lan9220_data, sizeof(lan9220_data));
+	regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	platform_device_register_resndata(&platform_bus, "sh_mmcif", 0,
+					  mmcif0_resources, ARRAY_SIZE(mmcif0_resources),
+					  &mmcif0_pdata, sizeof(mmcif0_pdata));
+	platform_device_register_resndata(&platform_bus, "sh_mobile_sdhi", 0,
+					  sdhi0_resources, ARRAY_SIZE(sdhi0_resources),
+					  &sdhi0_pdata, sizeof(sdhi0_pdata));
+	platform_device_register_resndata(&platform_bus, "sh_mobile_sdhi", 1,
+					  sdhi1_resources, ARRAY_SIZE(sdhi1_resources),
+					  &sdhi1_pdata, sizeof(sdhi1_pdata));
+	platform_device_register_data(&platform_bus, "gpio-keys", -1,
+				      &ape6evm_keys_pdata,
+				      sizeof(ape6evm_keys_pdata));
+	platform_device_register_data(&platform_bus, "leds-gpio", -1,
+				      &ape6evm_leds_pdata,
+				      sizeof(ape6evm_leds_pdata));
 }
 
 static const char *ape6evm_boards_compat_dt[] __initdata = {
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
index 4e3670a..6b4b77d 100644
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ b/arch/arm/mach-shmobile/board-armadillo800eva.c
@@ -31,6 +31,8 @@
 #include <linux/gpio_keys.h>
 #include <linux/regulator/driver.h>
 #include <linux/pinctrl/machine.h>
+#include <linux/platform_data/pwm-renesas-tpu.h>
+#include <linux/pwm_backlight.h>
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/gpio-regulator.h>
 #include <linux/regulator/machine.h>
@@ -386,7 +388,50 @@ static struct platform_device sh_eth_device = {
 	.num_resources = ARRAY_SIZE(sh_eth_resources),
 };
 
-/* LCDC */
+/* PWM */
+static struct resource pwm_resources[] = {
+	[0] = {
+		.start = 0xe6600000,
+		.end = 0xe66000ff,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct tpu_pwm_platform_data pwm_device_data = {
+	.channels[2] = {
+		.polarity = PWM_POLARITY_INVERSED,
+	}
+};
+
+static struct platform_device pwm_device = {
+	.name = "renesas-tpu-pwm",
+	.id = -1,
+	.dev = {
+		.platform_data = &pwm_device_data,
+	},
+	.num_resources = ARRAY_SIZE(pwm_resources),
+	.resource = pwm_resources,
+};
+
+static struct pwm_lookup pwm_lookup[] = {
+	PWM_LOOKUP("renesas-tpu-pwm", 2, "pwm-backlight.0", NULL),
+};
+
+/* LCDC and backlight */
+static struct platform_pwm_backlight_data pwm_backlight_data = {
+	.lth_brightness = 50,
+	.max_brightness = 255,
+	.dft_brightness = 255,
+	.pwm_period_ns = 33333, /* 30kHz */
+};
+
+static struct platform_device pwm_backlight_device = {
+	.name = "pwm-backlight",
+	.dev = {
+		.platform_data = &pwm_backlight_data,
+	},
+};
+
 static struct fb_videomode lcdc0_mode = {
 	.name		= "AMPIER/AM-800480",
 	.xres		= 800,
@@ -778,6 +823,8 @@ static struct sh_mmcif_plat_data sh_mmcif_plat = {
 	.caps		= MMC_CAP_4_BIT_DATA |
 			  MMC_CAP_8_BIT_DATA |
 			  MMC_CAP_NONREMOVABLE,
+	.slave_id_tx	= SHDMA_SLAVE_MMCIF_TX,
+	.slave_id_rx	= SHDMA_SLAVE_MMCIF_RX,
 };
 
 static struct resource sh_mmcif_resources[] = {
@@ -1020,6 +1067,8 @@ static struct i2c_board_info i2c2_devices[] = {
  */
 static struct platform_device *eva_devices[] __initdata = {
 	&lcdc0_device,
+	&pwm_device,
+	&pwm_backlight_device,
 	&gpio_keys_device,
 	&sh_eth_device,
 	&vcc_sdhi0,
@@ -1091,6 +1140,9 @@ static const struct pinctrl_map eva_pinctrl_map[] = {
 	/* ST1232 */
 	PIN_MAP_MUX_GROUP_DEFAULT("0-0055", "pfc-r8a7740",
 				  "intc_irq10", "intc"),
+	/* TPU0 */
+	PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm", "pfc-r8a7740",
+				  "tpu0_to2_1", "tpu0"),
 	/* USBHS */
 	PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-r8a7740",
 				  "intc_irq7_1", "intc"),
@@ -1144,13 +1196,13 @@ static void __init eva_init(void)
 				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
 
 	pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map));
+	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
 
 	r8a7740_pinmux_init();
 	r8a7740_meram_workaround();
 
 	/* LCDC0 */
 	gpio_request_one(61, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
-	gpio_request_one(202, GPIOF_OUT_INIT_LOW, NULL); /* LCD0_LED_CONT */
 
 	/* GETHER */
 	gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
diff --git a/arch/arm/mach-shmobile/board-kota2.c b/arch/arm/mach-shmobile/board-kota2.c
index ef5ca0e..6af20d9 100644
--- a/arch/arm/mach-shmobile/board-kota2.c
+++ b/arch/arm/mach-shmobile/board-kota2.c
@@ -26,6 +26,7 @@
 #include <linux/irq.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/pinctrl/pinconf-generic.h>
+#include <linux/platform_data/pwm-renesas-tpu.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/io.h>
@@ -37,8 +38,8 @@
 #include <linux/input/sh_keysc.h>
 #include <linux/gpio_keys.h>
 #include <linux/leds.h>
+#include <linux/leds_pwm.h>
 #include <linux/irqchip/arm-gic.h>
-#include <linux/platform_data/leds-renesas-tpu.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/sh_mmcif.h>
 #include <linux/mfd/tmio.h>
@@ -186,116 +187,100 @@ static struct platform_device gpio_leds_device = {
 };
 
 /* TPU LED */
-static struct led_renesas_tpu_config led_renesas_tpu12_pdata = {
-	.name		= "V2513",
-	.pin_gpio_fn	= GPIO_FN_TPU1TO2,
-	.pin_gpio	= 153,
-	.channel_offset = 0x90,
-	.timer_bit = 2,
-	.max_brightness = 1000,
-};
-
-static struct resource tpu12_resources[] = {
+static struct resource tpu1_pwm_resources[] = {
 	[0] = {
-		.name	= "TPU12",
-		.start	= 0xe6610090,
-		.end	= 0xe66100b5,
+		.start	= 0xe6610000,
+		.end	= 0xe66100ff,
 		.flags	= IORESOURCE_MEM,
 	},
 };
 
-static struct platform_device leds_tpu12_device = {
-	.name = "leds-renesas-tpu",
-	.id = 12,
-	.dev = {
-		.platform_data  = &led_renesas_tpu12_pdata,
-	},
-	.num_resources	= ARRAY_SIZE(tpu12_resources),
-	.resource	= tpu12_resources,
+static struct platform_device tpu1_pwm_device = {
+	.name = "renesas-tpu-pwm",
+	.id = 1,
+	.num_resources	= ARRAY_SIZE(tpu1_pwm_resources),
+	.resource	= tpu1_pwm_resources,
 };
 
-static struct led_renesas_tpu_config led_renesas_tpu41_pdata = {
-	.name		= "V2514",
-	.pin_gpio_fn	= GPIO_FN_TPU4TO1,
-	.pin_gpio	= 199,
-	.channel_offset = 0x50,
-	.timer_bit = 1,
-	.max_brightness = 1000,
-};
-
-static struct resource tpu41_resources[] = {
+static struct resource tpu2_pwm_resources[] = {
 	[0] = {
-		.name	= "TPU41",
-		.start	= 0xe6640050,
-		.end	= 0xe6640075,
+		.start	= 0xe6620000,
+		.end	= 0xe66200ff,
 		.flags	= IORESOURCE_MEM,
 	},
 };
 
-static struct platform_device leds_tpu41_device = {
-	.name = "leds-renesas-tpu",
-	.id = 41,
-	.dev = {
-		.platform_data  = &led_renesas_tpu41_pdata,
+static struct platform_device tpu2_pwm_device = {
+	.name = "renesas-tpu-pwm",
+	.id = 2,
+	.num_resources	= ARRAY_SIZE(tpu2_pwm_resources),
+	.resource	= tpu2_pwm_resources,
+};
+
+static struct resource tpu3_pwm_resources[] = {
+	[0] = {
+		.start	= 0xe6630000,
+		.end	= 0xe66300ff,
+		.flags	= IORESOURCE_MEM,
 	},
-	.num_resources	= ARRAY_SIZE(tpu41_resources),
-	.resource	= tpu41_resources,
 };
 
-static struct led_renesas_tpu_config led_renesas_tpu21_pdata = {
-	.name		= "V2515",
-	.pin_gpio_fn	= GPIO_FN_TPU2TO1,
-	.pin_gpio	= 197,
-	.channel_offset = 0x50,
-	.timer_bit = 1,
-	.max_brightness = 1000,
+static struct platform_device tpu3_pwm_device = {
+	.name = "renesas-tpu-pwm",
+	.id = 3,
+	.num_resources	= ARRAY_SIZE(tpu3_pwm_resources),
+	.resource	= tpu3_pwm_resources,
 };
 
-static struct resource tpu21_resources[] = {
+static struct resource tpu4_pwm_resources[] = {
 	[0] = {
-		.name	= "TPU21",
-		.start	= 0xe6620050,
-		.end	= 0xe6620075,
+		.start	= 0xe6640000,
+		.end	= 0xe66400ff,
 		.flags	= IORESOURCE_MEM,
 	},
 };
 
-static struct platform_device leds_tpu21_device = {
-	.name = "leds-renesas-tpu",
-	.id = 21,
-	.dev = {
-		.platform_data  = &led_renesas_tpu21_pdata,
+static struct platform_device tpu4_pwm_device = {
+	.name = "renesas-tpu-pwm",
+	.id = 4,
+	.num_resources	= ARRAY_SIZE(tpu4_pwm_resources),
+	.resource	= tpu4_pwm_resources,
+};
+
+static struct pwm_lookup pwm_lookup[] = {
+	PWM_LOOKUP("renesas-tpu-pwm.1", 2, "leds-pwm.0", "V2513"),
+	PWM_LOOKUP("renesas-tpu-pwm.2", 1, "leds-pwm.0", "V2515"),
+	PWM_LOOKUP("renesas-tpu-pwm.3", 0, "leds-pwm.0", "KEYLED"),
+	PWM_LOOKUP("renesas-tpu-pwm.4", 1, "leds-pwm.0", "V2514"),
+};
+
+static struct led_pwm tpu_pwm_leds[] = {
+	{
+		.name		= "V2513",
+		.max_brightness	= 1000,
+	}, {
+		.name		= "V2515",
+		.max_brightness	= 1000,
+	}, {
+		.name		= "KEYLED",
+		.max_brightness	= 1000,
+	}, {
+		.name		= "V2514",
+		.max_brightness	= 1000,
 	},
-	.num_resources	= ARRAY_SIZE(tpu21_resources),
-	.resource	= tpu21_resources,
 };
 
-static struct led_renesas_tpu_config led_renesas_tpu30_pdata = {
-	.name		= "KEYLED",
-	.pin_gpio_fn	= GPIO_FN_TPU3TO0,
-	.pin_gpio	= 163,
-	.channel_offset = 0x10,
-	.timer_bit = 0,
-	.max_brightness = 1000,
+static struct led_pwm_platform_data leds_pwm_pdata = {
+	.num_leds = ARRAY_SIZE(tpu_pwm_leds),
+	.leds = tpu_pwm_leds,
 };
 
-static struct resource tpu30_resources[] = {
-	[0] = {
-		.name	= "TPU30",
-		.start	= 0xe6630010,
-		.end	= 0xe6630035,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device leds_tpu30_device = {
-	.name = "leds-renesas-tpu",
-	.id = 30,
+static struct platform_device leds_pwm_device = {
+	.name = "leds-pwm",
+	.id = 0,
 	.dev = {
-		.platform_data  = &led_renesas_tpu30_pdata,
+		.platform_data = &leds_pwm_pdata,
 	},
-	.num_resources	= ARRAY_SIZE(tpu30_resources),
-	.resource	= tpu30_resources,
 };
 
 /* Fixed 1.8V regulator to be used by MMCIF */
@@ -426,10 +411,11 @@ static struct platform_device *kota2_devices[] __initdata = {
 	&keysc_device,
 	&gpio_keys_device,
 	&gpio_leds_device,
-	&leds_tpu12_device,
-	&leds_tpu41_device,
-	&leds_tpu21_device,
-	&leds_tpu30_device,
+	&tpu1_pwm_device,
+	&tpu2_pwm_device,
+	&tpu3_pwm_device,
+	&tpu4_pwm_device,
+	&leds_pwm_device,
 	&mmcif_device,
 	&sdhi0_device,
 	&sdhi1_device,
@@ -512,6 +498,15 @@ static const struct pinctrl_map kota2_pinctrl_map[] = {
 				  "bsc_cs5_a", "bsc"),
 	PIN_MAP_MUX_GROUP_DEFAULT("smsc911x.0", "pfc-sh73a0",
 				  "bsc_we0", "bsc"),
+	/* TPU */
+	PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm.1", "pfc-sh73a0",
+				  "tpu1_to2", "tpu1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm.2", "pfc-sh73a0",
+				  "tpu2_to1", "tpu2"),
+	PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm.3", "pfc-sh73a0",
+				  "tpu3_to0", "tpu3"),
+	PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm.4", "pfc-sh73a0",
+				  "tpu4_to1", "tpu4"),
 };
 
 static void __init kota2_init(void)
@@ -524,6 +519,8 @@ static void __init kota2_init(void)
 
 	pinctrl_register_mappings(kota2_pinctrl_map,
 				  ARRAY_SIZE(kota2_pinctrl_map));
+	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
+
 	sh73a0_pinmux_init();
 
 	/* SMSC911X */
diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c
index f89f166..4872939 100644
--- a/arch/arm/mach-shmobile/board-lager.c
+++ b/arch/arm/mach-shmobile/board-lager.c
@@ -24,10 +24,16 @@
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/sh_mmcif.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/gpio-rcar.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/sh_eth.h>
 #include <mach/common.h>
+#include <mach/irqs.h>
 #include <mach/r8a7790.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -70,6 +76,36 @@ static __initdata struct gpio_keys_platform_data lager_keys_pdata = {
 	.nbuttons	= ARRAY_SIZE(gpio_buttons),
 };
 
+/* Fixed 3.3V regulator to be used by MMCIF */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.1"),
+};
+
+/* MMCIF */
+static struct sh_mmcif_plat_data mmcif1_pdata __initdata = {
+	.caps		= MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+};
+
+static struct resource mmcif1_resources[] __initdata = {
+	DEFINE_RES_MEM_NAMED(0xee220000, 0x80, "MMCIF1"),
+	DEFINE_RES_IRQ(gic_spi(170)),
+};
+
+/* Ether */
+static struct sh_eth_plat_data ether_pdata __initdata = {
+	.phy			= 0x1,
+	.edmac_endian		= EDMAC_LITTLE_ENDIAN,
+	.register_type		= SH_ETH_REG_FAST_RCAR,
+	.phy_interface		= PHY_INTERFACE_MODE_RMII,
+	.ether_link_active_low	= 1,
+};
+
+static struct resource ether_resources[] __initdata = {
+	DEFINE_RES_MEM(0xee700000, 0x400),
+	DEFINE_RES_IRQ(gic_spi(162)),
+};
+
 static const struct pinctrl_map lager_pinctrl_map[] = {
 	/* SCIF0 (CN19: DEBUG SERIAL0) */
 	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790",
@@ -77,6 +113,20 @@ static const struct pinctrl_map lager_pinctrl_map[] = {
 	/* SCIF1 (CN20: DEBUG SERIAL1) */
 	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.7", "pfc-r8a7790",
 				  "scif1_data", "scif1"),
+	/* MMCIF1 */
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.1", "pfc-r8a7790",
+				  "mmc1_data8", "mmc1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.1", "pfc-r8a7790",
+				  "mmc1_ctrl", "mmc1"),
+	/* Ether */
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7790-ether", "pfc-r8a7790",
+				  "eth_link", "eth"),
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7790-ether", "pfc-r8a7790",
+				  "eth_mdio", "eth"),
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7790-ether", "pfc-r8a7790",
+				  "eth_rmii", "eth"),
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7790-ether", "pfc-r8a7790",
+				  "intc_irq0", "intc"),
 };
 
 static void __init lager_add_standard_devices(void)
@@ -94,6 +144,16 @@ static void __init lager_add_standard_devices(void)
 	platform_device_register_data(&platform_bus, "gpio-keys", -1,
 				      &lager_keys_pdata,
 				      sizeof(lager_keys_pdata));
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	platform_device_register_resndata(&platform_bus, "sh_mmcif", 1,
+					  mmcif1_resources, ARRAY_SIZE(mmcif1_resources),
+					  &mmcif1_pdata, sizeof(mmcif1_pdata));
+
+	platform_device_register_resndata(&platform_bus, "r8a7790-ether", -1,
+					  ether_resources,
+					  ARRAY_SIZE(ether_resources),
+					  &ether_pdata, sizeof(ether_pdata));
 }
 
 static const char *lager_boards_compat_dt[] __initdata = {
diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index 85f51a8..af06753 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -41,6 +41,7 @@
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/sh_flctl.h>
 #include <linux/pinctrl/machine.h>
+#include <linux/platform_data/gpio_backlight.h>
 #include <linux/pm_clock.h>
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
@@ -49,7 +50,6 @@
 #include <linux/tca6416_keypad.h>
 #include <linux/usb/renesas_usbhs.h>
 #include <linux/dma-mapping.h>
-
 #include <video/sh_mobile_hdmi.h>
 #include <video/sh_mobile_lcdc.h>
 #include <media/sh_mobile_ceu.h>
@@ -346,7 +346,7 @@ static struct platform_device meram_device = {
 	},
 };
 
-/* LCDC */
+/* LCDC and backlight */
 static struct fb_videomode mackerel_lcdc_modes[] = {
 	{
 		.name		= "WVGA Panel",
@@ -362,13 +362,6 @@ static struct fb_videomode mackerel_lcdc_modes[] = {
 	},
 };
 
-static int mackerel_set_brightness(int brightness)
-{
-	gpio_set_value(31, brightness);
-
-	return 0;
-}
-
 static const struct sh_mobile_meram_cfg lcd_meram_cfg = {
 	.icb[0] = {
 		.meram_size     = 0x40,
@@ -393,11 +386,6 @@ static struct sh_mobile_lcdc_info lcdc_info = {
 			.width		= 152,
 			.height		= 91,
 		},
-		.bl_info = {
-			.name = "sh_mobile_lcdc_bl",
-			.max_brightness = 1,
-			.set_brightness = mackerel_set_brightness,
-		},
 		.meram_cfg = &lcd_meram_cfg,
 	}
 };
@@ -425,6 +413,20 @@ static struct platform_device lcdc_device = {
 	},
 };
 
+static struct gpio_backlight_platform_data gpio_backlight_data = {
+	.fbdev = &lcdc_device.dev,
+	.gpio = 31,
+	.def_value = 1,
+	.name = "backlight",
+};
+
+static struct platform_device gpio_backlight_device = {
+	.name = "gpio-backlight",
+	.dev = {
+		.platform_data = &gpio_backlight_data,
+	},
+};
+
 /* HDMI */
 static struct sh_mobile_hdmi_info hdmi_info = {
 	.flags		= HDMI_SND_SRC_SPDIF,
@@ -1231,6 +1233,7 @@ static struct platform_device *mackerel_devices[] __initdata = {
 	&nor_flash_device,
 	&smc911x_device,
 	&lcdc_device,
+	&gpio_backlight_device,
 	&usbhs0_device,
 	&usbhs1_device,
 	&leds_device,
@@ -1441,9 +1444,6 @@ static void __init mackerel_init(void)
 				  ARRAY_SIZE(mackerel_pinctrl_map));
 	sh7372_pinmux_init();
 
-	/* backlight, off by default */
-	gpio_request_one(31, GPIOF_OUT_INIT_LOW, NULL);
-
 	gpio_request_one(151, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
 
 	/* USBHS0 */
diff --git a/arch/arm/mach-shmobile/clock-sh73a0.c b/arch/arm/mach-shmobile/clock-sh73a0.c
index d9fd033..1942eae 100644
--- a/arch/arm/mach-shmobile/clock-sh73a0.c
+++ b/arch/arm/mach-shmobile/clock-sh73a0.c
@@ -555,7 +555,7 @@ enum { MSTP001,
 	MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
 	MSTP331, MSTP329, MSTP328, MSTP325, MSTP323, MSTP322,
 	MSTP314, MSTP313, MSTP312, MSTP311,
-	MSTP303, MSTP302, MSTP301, MSTP300,
+	MSTP304, MSTP303, MSTP302, MSTP301, MSTP300,
 	MSTP411, MSTP410, MSTP403,
 	MSTP_NR };
 
@@ -593,6 +593,7 @@ static struct clk mstp_clks[MSTP_NR] = {
 	[MSTP313] = MSTP(&div6_clks[DIV6_SDHI1], SMSTPCR3, 13, 0), /* SDHI1 */
 	[MSTP312] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 12, 0), /* MMCIF0 */
 	[MSTP311] = MSTP(&div6_clks[DIV6_SDHI2], SMSTPCR3, 11, 0), /* SDHI2 */
+	[MSTP304] = MSTP(&main_div2_clk, SMSTPCR3, 4, 0), /* TPU0 */
 	[MSTP303] = MSTP(&main_div2_clk, SMSTPCR3, 3, 0), /* TPU1 */
 	[MSTP302] = MSTP(&main_div2_clk, SMSTPCR3, 2, 0), /* TPU2 */
 	[MSTP301] = MSTP(&main_div2_clk, SMSTPCR3, 1, 0), /* TPU3 */
@@ -669,10 +670,11 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("e6bd0000.mmcif", &mstp_clks[MSTP312]), /* MMCIF0 */
 	CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP311]), /* SDHI2 */
 	CLKDEV_DEV_ID("ee140000.sdhi", &mstp_clks[MSTP311]), /* SDHI2 */
-	CLKDEV_DEV_ID("leds-renesas-tpu.12", &mstp_clks[MSTP303]), /* TPU1 */
-	CLKDEV_DEV_ID("leds-renesas-tpu.21", &mstp_clks[MSTP302]), /* TPU2 */
-	CLKDEV_DEV_ID("leds-renesas-tpu.30", &mstp_clks[MSTP301]), /* TPU3 */
-	CLKDEV_DEV_ID("leds-renesas-tpu.41", &mstp_clks[MSTP300]), /* TPU4 */
+	CLKDEV_DEV_ID("renesas-tpu-pwm.0", &mstp_clks[MSTP304]), /* TPU0 */
+	CLKDEV_DEV_ID("renesas-tpu-pwm.1", &mstp_clks[MSTP303]), /* TPU1 */
+	CLKDEV_DEV_ID("renesas-tpu-pwm.2", &mstp_clks[MSTP302]), /* TPU2 */
+	CLKDEV_DEV_ID("renesas-tpu-pwm.3", &mstp_clks[MSTP301]), /* TPU3 */
+	CLKDEV_DEV_ID("renesas-tpu-pwm.4", &mstp_clks[MSTP300]), /* TPU4 */
 	CLKDEV_DEV_ID("i2c-sh_mobile.3", &mstp_clks[MSTP411]), /* I2C3 */
 	CLKDEV_DEV_ID("e6826000.i2c", &mstp_clks[MSTP411]), /* I2C3 */
 	CLKDEV_DEV_ID("i2c-sh_mobile.4", &mstp_clks[MSTP410]), /* I2C4 */
diff --git a/arch/arm/mach-shmobile/include/mach/sh73a0.h b/arch/arm/mach-shmobile/include/mach/sh73a0.h
index eb7a432..680dc5f 100644
--- a/arch/arm/mach-shmobile/include/mach/sh73a0.h
+++ b/arch/arm/mach-shmobile/include/mach/sh73a0.h
@@ -1,378 +1,7 @@
 #ifndef __ASM_SH73A0_H__
 #define __ASM_SH73A0_H__
 
-/* Pin Function Controller:
- * GPIO_FN_xx - GPIO used to select pin function and MSEL switch
- * GPIO_PORTxx - GPIO mapped to real I/O pin on CPU
- */
-enum {
-	/* Hardware manual Table 25-1 (GPIO) */
-	GPIO_PORT0, GPIO_PORT1, GPIO_PORT2, GPIO_PORT3, GPIO_PORT4,
-	GPIO_PORT5, GPIO_PORT6, GPIO_PORT7, GPIO_PORT8, GPIO_PORT9,
-
-	GPIO_PORT10, GPIO_PORT11, GPIO_PORT12, GPIO_PORT13, GPIO_PORT14,
-	GPIO_PORT15, GPIO_PORT16, GPIO_PORT17, GPIO_PORT18, GPIO_PORT19,
-
-	GPIO_PORT20, GPIO_PORT21, GPIO_PORT22, GPIO_PORT23, GPIO_PORT24,
-	GPIO_PORT25, GPIO_PORT26, GPIO_PORT27, GPIO_PORT28, GPIO_PORT29,
-
-	GPIO_PORT30, GPIO_PORT31, GPIO_PORT32, GPIO_PORT33, GPIO_PORT34,
-	GPIO_PORT35, GPIO_PORT36, GPIO_PORT37, GPIO_PORT38, GPIO_PORT39,
-
-	GPIO_PORT40, GPIO_PORT41, GPIO_PORT42, GPIO_PORT43, GPIO_PORT44,
-	GPIO_PORT45, GPIO_PORT46, GPIO_PORT47, GPIO_PORT48, GPIO_PORT49,
-
-	GPIO_PORT50, GPIO_PORT51, GPIO_PORT52, GPIO_PORT53, GPIO_PORT54,
-	GPIO_PORT55, GPIO_PORT56, GPIO_PORT57, GPIO_PORT58, GPIO_PORT59,
-
-	GPIO_PORT60, GPIO_PORT61, GPIO_PORT62, GPIO_PORT63, GPIO_PORT64,
-	GPIO_PORT65, GPIO_PORT66, GPIO_PORT67, GPIO_PORT68, GPIO_PORT69,
-
-	GPIO_PORT70, GPIO_PORT71, GPIO_PORT72, GPIO_PORT73, GPIO_PORT74,
-	GPIO_PORT75, GPIO_PORT76, GPIO_PORT77, GPIO_PORT78, GPIO_PORT79,
-
-	GPIO_PORT80, GPIO_PORT81, GPIO_PORT82, GPIO_PORT83, GPIO_PORT84,
-	GPIO_PORT85, GPIO_PORT86, GPIO_PORT87, GPIO_PORT88, GPIO_PORT89,
-
-	GPIO_PORT90, GPIO_PORT91, GPIO_PORT92, GPIO_PORT93, GPIO_PORT94,
-	GPIO_PORT95, GPIO_PORT96, GPIO_PORT97, GPIO_PORT98, GPIO_PORT99,
-
-	GPIO_PORT100, GPIO_PORT101, GPIO_PORT102, GPIO_PORT103, GPIO_PORT104,
-	GPIO_PORT105, GPIO_PORT106, GPIO_PORT107, GPIO_PORT108, GPIO_PORT109,
-
-	GPIO_PORT110, GPIO_PORT111, GPIO_PORT112, GPIO_PORT113, GPIO_PORT114,
-	GPIO_PORT115, GPIO_PORT116, GPIO_PORT117, GPIO_PORT118,
-
-	GPIO_PORT128, GPIO_PORT129,
-
-	GPIO_PORT130, GPIO_PORT131, GPIO_PORT132, GPIO_PORT133, GPIO_PORT134,
-	GPIO_PORT135, GPIO_PORT136, GPIO_PORT137, GPIO_PORT138, GPIO_PORT139,
-
-	GPIO_PORT140, GPIO_PORT141, GPIO_PORT142, GPIO_PORT143, GPIO_PORT144,
-	GPIO_PORT145, GPIO_PORT146, GPIO_PORT147, GPIO_PORT148, GPIO_PORT149,
-
-	GPIO_PORT150, GPIO_PORT151, GPIO_PORT152, GPIO_PORT153, GPIO_PORT154,
-	GPIO_PORT155, GPIO_PORT156, GPIO_PORT157, GPIO_PORT158, GPIO_PORT159,
-
-	GPIO_PORT160, GPIO_PORT161, GPIO_PORT162, GPIO_PORT163, GPIO_PORT164,
-
-	GPIO_PORT192, GPIO_PORT193, GPIO_PORT194,
-	GPIO_PORT195, GPIO_PORT196, GPIO_PORT197, GPIO_PORT198, GPIO_PORT199,
-
-	GPIO_PORT200, GPIO_PORT201, GPIO_PORT202, GPIO_PORT203, GPIO_PORT204,
-	GPIO_PORT205, GPIO_PORT206, GPIO_PORT207, GPIO_PORT208, GPIO_PORT209,
-
-	GPIO_PORT210, GPIO_PORT211, GPIO_PORT212, GPIO_PORT213, GPIO_PORT214,
-	GPIO_PORT215, GPIO_PORT216, GPIO_PORT217, GPIO_PORT218, GPIO_PORT219,
-
-	GPIO_PORT220, GPIO_PORT221, GPIO_PORT222, GPIO_PORT223, GPIO_PORT224,
-	GPIO_PORT225, GPIO_PORT226, GPIO_PORT227, GPIO_PORT228, GPIO_PORT229,
-
-	GPIO_PORT230, GPIO_PORT231, GPIO_PORT232, GPIO_PORT233, GPIO_PORT234,
-	GPIO_PORT235, GPIO_PORT236, GPIO_PORT237, GPIO_PORT238, GPIO_PORT239,
-
-	GPIO_PORT240, GPIO_PORT241, GPIO_PORT242, GPIO_PORT243, GPIO_PORT244,
-	GPIO_PORT245, GPIO_PORT246, GPIO_PORT247, GPIO_PORT248, GPIO_PORT249,
-
-	GPIO_PORT250, GPIO_PORT251, GPIO_PORT252, GPIO_PORT253, GPIO_PORT254,
-	GPIO_PORT255, GPIO_PORT256, GPIO_PORT257, GPIO_PORT258, GPIO_PORT259,
-
-	GPIO_PORT260, GPIO_PORT261, GPIO_PORT262, GPIO_PORT263, GPIO_PORT264,
-	GPIO_PORT265, GPIO_PORT266, GPIO_PORT267, GPIO_PORT268, GPIO_PORT269,
-
-	GPIO_PORT270, GPIO_PORT271, GPIO_PORT272, GPIO_PORT273, GPIO_PORT274,
-	GPIO_PORT275, GPIO_PORT276, GPIO_PORT277, GPIO_PORT278, GPIO_PORT279,
-
-	GPIO_PORT280, GPIO_PORT281, GPIO_PORT282,
-
-	GPIO_PORT288, GPIO_PORT289,
-
-	GPIO_PORT290, GPIO_PORT291, GPIO_PORT292, GPIO_PORT293, GPIO_PORT294,
-	GPIO_PORT295, GPIO_PORT296, GPIO_PORT297, GPIO_PORT298, GPIO_PORT299,
-
-	GPIO_PORT300, GPIO_PORT301, GPIO_PORT302, GPIO_PORT303, GPIO_PORT304,
-	GPIO_PORT305, GPIO_PORT306, GPIO_PORT307, GPIO_PORT308, GPIO_PORT309,
-
-	/* Table 25-1 (Function 0-7) */
-	GPIO_FN_GPI0 = 310,
-	GPIO_FN_GPI1,
-	GPIO_FN_GPI2,
-	GPIO_FN_GPI3,
-	GPIO_FN_GPI4,
-	GPIO_FN_GPI5,
-	GPIO_FN_GPI6,
-	GPIO_FN_GPI7,
-	GPIO_FN_GPO7, GPIO_FN_MFG0_OUT2,
-	GPIO_FN_GPO6, GPIO_FN_MFG1_OUT2,
-	GPIO_FN_GPO5,
-	GPIO_FN_PORT16_VIO_CKOR,
-	GPIO_FN_PORT19_VIO_CKO2,
-	GPIO_FN_GPO0,
-	GPIO_FN_GPO1,
-	GPIO_FN_GPO2, GPIO_FN_STATUS0,
-	GPIO_FN_GPO3, GPIO_FN_STATUS1,
-	GPIO_FN_GPO4, GPIO_FN_STATUS2,
-	GPIO_FN_VINT,
-	GPIO_FN_TCKON,
-	GPIO_FN_XDVFS1,
-	GPIO_FN_MFG0_OUT1, GPIO_FN_PORT27_IROUT,
-	GPIO_FN_XDVFS2,
-	GPIO_FN_PORT28_TPU1TO1,
-	GPIO_FN_SIM_RST, GPIO_FN_PORT29_TPU1TO1,
-	GPIO_FN_SIM_CLK, GPIO_FN_PORT30_VIO_CKOR,
-	GPIO_FN_SIM_D, GPIO_FN_PORT31_IROUT,
-	GPIO_FN_XWUP,
-	GPIO_FN_VACK,
-	GPIO_FN_XTAL1L,
-	GPIO_FN_PORT49_IROUT,
-	GPIO_FN_BBIF2_TSYNC2, GPIO_FN_TPU2TO2,
-
-	GPIO_FN_BBIF2_TSCK2, GPIO_FN_TPU2TO3,
-	GPIO_FN_BBIF2_TXD2,
-	GPIO_FN_TPU3TO3,
-	GPIO_FN_TPU3TO2,
-	GPIO_FN_TPU0TO0,
-	GPIO_FN_A0, GPIO_FN_BS_,
-	GPIO_FN_A12, GPIO_FN_TPU4TO2,
-	GPIO_FN_A13, GPIO_FN_TPU0TO1,
-	GPIO_FN_A14,
-	GPIO_FN_A15,
-	GPIO_FN_A16, GPIO_FN_MSIOF0_SS1,
-	GPIO_FN_A17, GPIO_FN_MSIOF0_TSYNC,
-	GPIO_FN_A18, GPIO_FN_MSIOF0_TSCK,
-	GPIO_FN_A19, GPIO_FN_MSIOF0_TXD,
-	GPIO_FN_A20, GPIO_FN_MSIOF0_RSCK,
-	GPIO_FN_A21, GPIO_FN_MSIOF0_RSYNC,
-	GPIO_FN_A22, GPIO_FN_MSIOF0_MCK0,
-	GPIO_FN_A23, GPIO_FN_MSIOF0_MCK1,
-	GPIO_FN_A24, GPIO_FN_MSIOF0_RXD,
-	GPIO_FN_A25, GPIO_FN_MSIOF0_SS2,
-	GPIO_FN_A26,
-	GPIO_FN_FCE1_,
-	GPIO_FN_DACK0,
-	GPIO_FN_FCE0_,
-	GPIO_FN_WAIT_, GPIO_FN_DREQ0,
-	GPIO_FN_FRB,
-	GPIO_FN_CKO,
-	GPIO_FN_NBRSTOUT_,
-	GPIO_FN_NBRST_,
-	GPIO_FN_BBIF2_TXD,
-	GPIO_FN_BBIF2_RXD,
-	GPIO_FN_BBIF2_SYNC,
-	GPIO_FN_BBIF2_SCK,
-	GPIO_FN_MFG3_IN2,
-	GPIO_FN_MFG3_IN1,
-	GPIO_FN_BBIF1_SS2, GPIO_FN_MFG3_OUT1,
-	GPIO_FN_HSI_RX_DATA, GPIO_FN_BBIF1_RXD,
-	GPIO_FN_HSI_TX_WAKE, GPIO_FN_BBIF1_TSCK,
-	GPIO_FN_HSI_TX_DATA, GPIO_FN_BBIF1_TSYNC,
-	GPIO_FN_HSI_TX_READY, GPIO_FN_BBIF1_TXD,
-	GPIO_FN_HSI_RX_READY, GPIO_FN_BBIF1_RSCK,
-	GPIO_FN_HSI_RX_WAKE, GPIO_FN_BBIF1_RSYNC,
-	GPIO_FN_HSI_RX_FLAG, GPIO_FN_BBIF1_SS1, GPIO_FN_BBIF1_FLOW,
-	GPIO_FN_HSI_TX_FLAG,
-	GPIO_FN_VIO_VD, GPIO_FN_VIO2_VD,
-
-	GPIO_FN_VIO_HD,
-	GPIO_FN_VIO2_HD,
-	GPIO_FN_VIO_D0, GPIO_FN_PORT130_MSIOF2_RXD,
-	GPIO_FN_VIO_D1, GPIO_FN_PORT131_MSIOF2_SS1,
-	GPIO_FN_VIO_D2, GPIO_FN_PORT132_MSIOF2_SS2,
-	GPIO_FN_VIO_D3, GPIO_FN_MSIOF2_TSYNC,
-	GPIO_FN_VIO_D4, GPIO_FN_MSIOF2_TXD,
-	GPIO_FN_VIO_D5, GPIO_FN_MSIOF2_TSCK,
-	GPIO_FN_VIO_D6,
-	GPIO_FN_VIO_D7,
-	GPIO_FN_VIO_D8, GPIO_FN_VIO2_D0,
-	GPIO_FN_VIO_D9, GPIO_FN_VIO2_D1,
-	GPIO_FN_VIO_D10, GPIO_FN_TPU0TO2, GPIO_FN_VIO2_D2,
-	GPIO_FN_VIO_D11, GPIO_FN_TPU0TO3, GPIO_FN_VIO2_D3,
-	GPIO_FN_VIO_D12, GPIO_FN_VIO2_D4,
-	GPIO_FN_VIO_D13,
-	GPIO_FN_VIO2_D5,
-	GPIO_FN_VIO_D14, GPIO_FN_VIO2_D6,
-	GPIO_FN_VIO_D15, GPIO_FN_TPU1TO3,
-	GPIO_FN_VIO2_D7,
-	GPIO_FN_VIO_CLK,
-	GPIO_FN_VIO2_CLK,
-	GPIO_FN_VIO_FIELD, GPIO_FN_VIO2_FIELD,
-	GPIO_FN_VIO_CKO,
-	GPIO_FN_A27, GPIO_FN_MFG0_IN1,
-	GPIO_FN_MFG0_IN2,
-	GPIO_FN_TS_SPSYNC3, GPIO_FN_MSIOF2_RSCK,
-	GPIO_FN_TS_SDAT3, GPIO_FN_MSIOF2_RSYNC,
-	GPIO_FN_TPU1TO2, GPIO_FN_TS_SDEN3, GPIO_FN_PORT153_MSIOF2_SS1,
-	GPIO_FN_MSIOF2_MCK0,
-	GPIO_FN_MSIOF2_MCK1,
-	GPIO_FN_PORT156_MSIOF2_SS2,
-	GPIO_FN_PORT157_MSIOF2_RXD,
-	GPIO_FN_DINT_, GPIO_FN_TS_SCK3,
-	GPIO_FN_NMI,
-	GPIO_FN_TPU3TO0,
-	GPIO_FN_BBIF2_TSYNC1,
-	GPIO_FN_BBIF2_TSCK1,
-	GPIO_FN_BBIF2_TXD1,
-	GPIO_FN_MFG2_OUT2,
-	GPIO_FN_TPU2TO1,
-	GPIO_FN_TPU4TO1, GPIO_FN_MFG4_OUT2,
-	GPIO_FN_D16,
-	GPIO_FN_D17,
-	GPIO_FN_D18,
-	GPIO_FN_D19,
-	GPIO_FN_D20,
-	GPIO_FN_D21,
-	GPIO_FN_D22,
-	GPIO_FN_PORT207_MSIOF0L_SS1, GPIO_FN_D23,
-	GPIO_FN_PORT208_MSIOF0L_SS2, GPIO_FN_D24,
-	GPIO_FN_D25,
-	GPIO_FN_DREQ2, GPIO_FN_PORT210_MSIOF0L_SS1, GPIO_FN_D26,
-	GPIO_FN_PORT211_MSIOF0L_SS2, GPIO_FN_D27,
-	GPIO_FN_TS_SPSYNC1, GPIO_FN_MSIOF0L_MCK0, GPIO_FN_D28,
-	GPIO_FN_TS_SDAT1, GPIO_FN_MSIOF0L_MCK1, GPIO_FN_D29,
-	GPIO_FN_TS_SDEN1, GPIO_FN_MSIOF0L_RSCK, GPIO_FN_D30,
-	GPIO_FN_TS_SCK1, GPIO_FN_MSIOF0L_RSYNC, GPIO_FN_D31,
-	GPIO_FN_DACK2,
-	GPIO_FN_MSIOF0L_TSYNC, GPIO_FN_VIO2_FIELD3,
-	GPIO_FN_DACK3,
-	GPIO_FN_PORT218_VIO_CKOR,
-	GPIO_FN_DREQ3, GPIO_FN_MSIOF0L_TSCK, GPIO_FN_VIO2_CLK3, \
-	GPIO_FN_DREQ1,
-	GPIO_FN_PWEN, GPIO_FN_MSIOF0L_RXD, GPIO_FN_VIO2_HD3, \
-	GPIO_FN_DACK1, GPIO_FN_OVCN,
-	GPIO_FN_MSIOF0L_TXD, GPIO_FN_VIO2_VD3,
-
-	GPIO_FN_OVCN2,
-	GPIO_FN_EXTLP, GPIO_FN_PORT226_VIO_CKO2,
-	GPIO_FN_IDIN,
-	GPIO_FN_MFG1_IN1,
-	GPIO_FN_MSIOF1_TXD,
-	GPIO_FN_MSIOF1_TSYNC,
-	GPIO_FN_MSIOF1_TSCK,
-	GPIO_FN_MSIOF1_RXD,
-	GPIO_FN_MSIOF1_RSCK, GPIO_FN_VIO2_CLK2,
-	GPIO_FN_MSIOF1_RSYNC, GPIO_FN_MFG1_IN2, GPIO_FN_VIO2_VD2, \
-	GPIO_FN_MSIOF1_MCK0,
-	GPIO_FN_MSIOF1_MCK1,
-	GPIO_FN_MSIOF1_SS1, GPIO_FN_VIO2_FIELD2,
-	GPIO_FN_MSIOF1_SS2, GPIO_FN_VIO2_HD2,
-	GPIO_FN_PORT241_IROUT, GPIO_FN_MFG4_OUT1, \
-	GPIO_FN_TPU4TO0,
-	GPIO_FN_MFG4_IN2,
-	GPIO_FN_PORT243_VIO_CKO2,
-	GPIO_FN_MFG2_IN1,
-	GPIO_FN_MSIOF2R_RXD,
-	GPIO_FN_MFG2_IN2,
-	GPIO_FN_MSIOF2R_TXD,
-	GPIO_FN_MFG1_OUT1,
-	GPIO_FN_TPU1TO0,
-	GPIO_FN_MFG3_OUT2,
-	GPIO_FN_TPU3TO1,
-	GPIO_FN_MFG2_OUT1,
-	GPIO_FN_TPU2TO0,
-	GPIO_FN_MSIOF2R_TSCK,
-	GPIO_FN_PORT249_IROUT, GPIO_FN_MFG4_IN1, \
-	GPIO_FN_MSIOF2R_TSYNC,
-	GPIO_FN_SDHICLK0,
-	GPIO_FN_SDHICD0,
-	GPIO_FN_SDHID0_0,
-	GPIO_FN_SDHID0_1,
-	GPIO_FN_SDHID0_2,
-	GPIO_FN_SDHID0_3,
-	GPIO_FN_SDHICMD0,
-	GPIO_FN_SDHIWP0,
-	GPIO_FN_SDHICLK1,
-	GPIO_FN_SDHID1_0, GPIO_FN_TS_SPSYNC2,
-	GPIO_FN_SDHID1_1, GPIO_FN_TS_SDAT2,
-	GPIO_FN_SDHID1_2, GPIO_FN_TS_SDEN2,
-	GPIO_FN_SDHID1_3, GPIO_FN_TS_SCK2,
-	GPIO_FN_SDHICMD1,
-	GPIO_FN_SDHICLK2,
-	GPIO_FN_SDHID2_0, GPIO_FN_TS_SPSYNC4,
-	GPIO_FN_SDHID2_1, GPIO_FN_TS_SDAT4,
-	GPIO_FN_SDHID2_2, GPIO_FN_TS_SDEN4,
-	GPIO_FN_SDHID2_3, GPIO_FN_TS_SCK4,
-	GPIO_FN_SDHICMD2,
-	GPIO_FN_MMCCLK0,
-	GPIO_FN_MMCD0_0,
-	GPIO_FN_MMCD0_1,
-	GPIO_FN_MMCD0_2,
-	GPIO_FN_MMCD0_3,
-	GPIO_FN_MMCD0_4, GPIO_FN_TS_SPSYNC5,
-	GPIO_FN_MMCD0_5, GPIO_FN_TS_SDAT5,
-	GPIO_FN_MMCD0_6, GPIO_FN_TS_SDEN5,
-	GPIO_FN_MMCD0_7, GPIO_FN_TS_SCK5,
-	GPIO_FN_MMCCMD0,
-	GPIO_FN_RESETOUTS_, GPIO_FN_EXTAL2OUT,
-	GPIO_FN_MCP_WAIT__MCP_FRB,
-	GPIO_FN_MCP_CKO, GPIO_FN_MMCCLK1,
-	GPIO_FN_MCP_D15_MCP_NAF15,
-	GPIO_FN_MCP_D14_MCP_NAF14,
-	GPIO_FN_MCP_D13_MCP_NAF13,
-	GPIO_FN_MCP_D12_MCP_NAF12,
-	GPIO_FN_MCP_D11_MCP_NAF11,
-	GPIO_FN_MCP_D10_MCP_NAF10,
-	GPIO_FN_MCP_D9_MCP_NAF9,
-	GPIO_FN_MCP_D8_MCP_NAF8, GPIO_FN_MMCCMD1,
-	GPIO_FN_MCP_D7_MCP_NAF7, GPIO_FN_MMCD1_7,
-
-	GPIO_FN_MCP_D6_MCP_NAF6, GPIO_FN_MMCD1_6,
-	GPIO_FN_MCP_D5_MCP_NAF5, GPIO_FN_MMCD1_5,
-	GPIO_FN_MCP_D4_MCP_NAF4, GPIO_FN_MMCD1_4,
-	GPIO_FN_MCP_D3_MCP_NAF3, GPIO_FN_MMCD1_3,
-	GPIO_FN_MCP_D2_MCP_NAF2, GPIO_FN_MMCD1_2,
-	GPIO_FN_MCP_D1_MCP_NAF1, GPIO_FN_MMCD1_1,
-	GPIO_FN_MCP_D0_MCP_NAF0, GPIO_FN_MMCD1_0,
-	GPIO_FN_MCP_NBRSTOUT_,
-	GPIO_FN_MCP_WE0__MCP_FWE, GPIO_FN_MCP_RDWR_MCP_FWE,
-
-	/* MSEL2 special case */
-	GPIO_FN_TSIF2_TS_XX1,
-	GPIO_FN_TSIF2_TS_XX2,
-	GPIO_FN_TSIF2_TS_XX3,
-	GPIO_FN_TSIF2_TS_XX4,
-	GPIO_FN_TSIF2_TS_XX5,
-	GPIO_FN_TSIF1_TS_XX1,
-	GPIO_FN_TSIF1_TS_XX2,
-	GPIO_FN_TSIF1_TS_XX3,
-	GPIO_FN_TSIF1_TS_XX4,
-	GPIO_FN_TSIF1_TS_XX5,
-	GPIO_FN_TSIF0_TS_XX1,
-	GPIO_FN_TSIF0_TS_XX2,
-	GPIO_FN_TSIF0_TS_XX3,
-	GPIO_FN_TSIF0_TS_XX4,
-	GPIO_FN_TSIF0_TS_XX5,
-	GPIO_FN_MST1_TS_XX1,
-	GPIO_FN_MST1_TS_XX2,
-	GPIO_FN_MST1_TS_XX3,
-	GPIO_FN_MST1_TS_XX4,
-	GPIO_FN_MST1_TS_XX5,
-	GPIO_FN_MST0_TS_XX1,
-	GPIO_FN_MST0_TS_XX2,
-	GPIO_FN_MST0_TS_XX3,
-	GPIO_FN_MST0_TS_XX4,
-	GPIO_FN_MST0_TS_XX5,
-
-	/* MSEL3 special cases */
-	GPIO_FN_SDHI0_VCCQ_MC0_ON,
-	GPIO_FN_SDHI0_VCCQ_MC0_OFF,
-	GPIO_FN_DEBUG_MON_VIO,
-	GPIO_FN_DEBUG_MON_LCDD,
-	GPIO_FN_LCDC_LCDC0,
-	GPIO_FN_LCDC_LCDC1,
-
-	/* MSEL4 special cases */
-	GPIO_FN_IRQ9_MEM_INT,
-	GPIO_FN_IRQ9_MCP_INT,
-	GPIO_FN_A11,
-	GPIO_FN_TPU4TO3,
-	GPIO_FN_RESETA_N_PU_ON,
-	GPIO_FN_RESETA_N_PU_OFF,
-	GPIO_FN_EDBGREQ_PD,
-	GPIO_FN_EDBGREQ_PU,
-
-	/* end of GPIO */
-	GPIO_NR,
-};
+#define GPIO_NR			310
 
 /* DMA slave IDs */
 enum {
diff --git a/arch/arm/plat-orion/irq.c b/arch/arm/plat-orion/irq.c
index 8db0b98..c492e1b 100644
--- a/arch/arm/plat-orion/irq.c
+++ b/arch/arm/plat-orion/irq.c
@@ -47,7 +47,7 @@ static int __init orion_add_irq_domain(struct device_node *np,
 	do {
 		base = of_iomap(np, i);
 		if (base) {
-			orion_irq_init(i * 32, base);
+			orion_irq_init(i * 32, base + 0x04);
 			i++;
 		}
 	} while (base);
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index a4f630f..65dd81b 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -30,6 +30,7 @@
 #include <linux/spi/mmc_spi.h>
 #include <linux/input.h>
 #include <linux/input/sh_keysc.h>
+#include <linux/platform_data/gpio_backlight.h>
 #include <linux/sh_eth.h>
 #include <linux/sh_intc.h>
 #include <linux/videodev2.h>
@@ -302,7 +303,7 @@ static struct platform_device usbhs_device = {
 	.resource	= usbhs_resources,
 };
 
-/* LCDC */
+/* LCDC and backlight */
 static const struct fb_videomode ecovec_lcd_modes[] = {
 	{
 		.name		= "Panel",
@@ -333,13 +334,6 @@ static const struct fb_videomode ecovec_dvi_modes[] = {
 	},
 };
 
-static int ecovec24_set_brightness(int brightness)
-{
-	gpio_set_value(GPIO_PTR1, brightness);
-
-	return 0;
-}
-
 static struct sh_mobile_lcdc_info lcdc_info = {
 	.ch[0] = {
 		.interface_type = RGB18,
@@ -349,11 +343,6 @@ static struct sh_mobile_lcdc_info lcdc_info = {
 			.width = 152,
 			.height = 91,
 		},
-		.bl_info = {
-			.name = "sh_mobile_lcdc_bl",
-			.max_brightness = 1,
-			.set_brightness = ecovec24_set_brightness,
-		},
 	}
 };
 
@@ -379,6 +368,20 @@ static struct platform_device lcdc_device = {
 	},
 };
 
+static struct gpio_backlight_platform_data gpio_backlight_data = {
+	.fbdev = &lcdc_device.dev,
+	.gpio = GPIO_PTR1,
+	.def_value = 1,
+	.name = "backlight",
+};
+
+static struct platform_device gpio_backlight_device = {
+	.name = "gpio-backlight",
+	.dev = {
+		.platform_data = &gpio_backlight_data,
+	},
+};
+
 /* CEU0 */
 static struct sh_mobile_ceu_info sh_mobile_ceu0_info = {
 	.flags = SH_CEU_FLAG_USE_8BIT_BUS,
@@ -1048,6 +1051,7 @@ static struct platform_device *ecovec_devices[] __initdata = {
 	&usb1_common_device,
 	&usbhs_device,
 	&lcdc_device,
+	&gpio_backlight_device,
 	&ceu0_device,
 	&ceu1_device,
 	&keysc_device,
@@ -1238,11 +1242,9 @@ static int __init arch_setup(void)
 
 	gpio_request(GPIO_PTE6, NULL);
 	gpio_request(GPIO_PTU1, NULL);
-	gpio_request(GPIO_PTR1, NULL);
 	gpio_request(GPIO_PTA2, NULL);
 	gpio_direction_input(GPIO_PTE6);
 	gpio_direction_output(GPIO_PTU1, 0);
-	gpio_direction_output(GPIO_PTR1, 0);
 	gpio_direction_output(GPIO_PTA2, 0);
 
 	/* I/O buffer drive ability is high */
@@ -1255,6 +1257,9 @@ static int __init arch_setup(void)
 		lcdc_info.ch[0].lcd_modes		= ecovec_dvi_modes;
 		lcdc_info.ch[0].num_modes		= ARRAY_SIZE(ecovec_dvi_modes);
 
+		/* No backlight */
+		gpio_backlight_data.fbdev = NULL;
+
 		gpio_set_value(GPIO_PTA2, 1);
 		gpio_set_value(GPIO_PTU1, 1);
 	} else {
@@ -1264,8 +1269,6 @@ static int __init arch_setup(void)
 		lcdc_info.ch[0].lcd_modes		= ecovec_lcd_modes;
 		lcdc_info.ch[0].num_modes		= ARRAY_SIZE(ecovec_lcd_modes);
 
-		gpio_set_value(GPIO_PTR1, 1);
-
 		/* FIXME
 		 *
 		 * LCDDON control is needed for Panel,
diff --git a/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c b/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c
index c620503..355a78a 100644
--- a/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c
+++ b/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c
@@ -276,51 +276,3 @@ void kfr2r09_lcd_start(void *sohandle, struct sh_mobile_lcdc_sys_bus_ops *so)
 {
 	write_memory_start(sohandle, so);
 }
-
-#define CTRL_CKSW       0x10
-#define CTRL_C10        0x20
-#define CTRL_CPSW       0x80
-#define MAIN_MLED4      0x40
-#define MAIN_MSW        0x80
-
-int kfr2r09_lcd_set_brightness(int brightness)
-{
-	struct i2c_adapter *a;
-	struct i2c_msg msg;
-	unsigned char buf[2];
-	int ret;
-
-	a = i2c_get_adapter(0);
-	if (!a)
-		return -ENODEV;
-
-	buf[0] = 0x00;
-	if (brightness)
-		buf[1] = CTRL_CPSW | CTRL_C10 | CTRL_CKSW;
-	else
-		buf[1] = 0;
-
-	msg.addr = 0x75;
-	msg.buf = buf;
-	msg.len = 2;
-	msg.flags = 0;
-	ret = i2c_transfer(a, &msg, 1);
-	if (ret != 1)
-		return -ENODEV;
-
-	buf[0] = 0x01;
-	if (brightness)
-		buf[1] = MAIN_MSW | MAIN_MLED4 | 0x0c;
-	else
-		buf[1] = 0;
-
-	msg.addr = 0x75;
-	msg.buf = buf;
-	msg.len = 2;
-	msg.flags = 0;
-	ret = i2c_transfer(a, &msg, 1);
-	if (ret != 1)
-		return -ENODEV;
-
-	return 0;
-}
diff --git a/arch/sh/boards/mach-kfr2r09/setup.c b/arch/sh/boards/mach-kfr2r09/setup.c
index ab502f12..1df4398 100644
--- a/arch/sh/boards/mach-kfr2r09/setup.c
+++ b/arch/sh/boards/mach-kfr2r09/setup.c
@@ -21,6 +21,7 @@
 #include <linux/input.h>
 #include <linux/input/sh_keysc.h>
 #include <linux/i2c.h>
+#include <linux/platform_data/lv5207lp.h>
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/usb/r8a66597.h>
@@ -159,11 +160,6 @@ static struct sh_mobile_lcdc_info kfr2r09_sh_lcdc_info = {
 			.setup_sys = kfr2r09_lcd_setup,
 			.start_transfer = kfr2r09_lcd_start,
 		},
-		.bl_info = {
-			.name = "sh_mobile_lcdc_bl",
-			.max_brightness = 1,
-			.set_brightness = kfr2r09_lcd_set_brightness,
-		},
 		.sys_bus_cfg = {
 			.ldmt2r = 0x07010904,
 			.ldmt3r = 0x14012914,
@@ -195,6 +191,17 @@ static struct platform_device kfr2r09_sh_lcdc_device = {
 	},
 };
 
+static struct lv5207lp_platform_data kfr2r09_backlight_data = {
+	.fbdev = &kfr2r09_sh_lcdc_device.dev,
+	.def_value = 13,
+	.max_value = 13,
+};
+
+static struct i2c_board_info kfr2r09_backlight_board_info = {
+	I2C_BOARD_INFO("lv5207lp", 0x75),
+	.platform_data = &kfr2r09_backlight_data,
+};
+
 static struct r8a66597_platdata kfr2r09_usb0_gadget_data = {
 	.on_chip = 1,
 };
@@ -627,6 +634,8 @@ static int __init kfr2r09_devices_setup(void)
 	gpio_request(GPIO_FN_SDHI0CMD, NULL);
 	gpio_request(GPIO_FN_SDHI0CLK, NULL);
 
+	i2c_register_board_info(0, &kfr2r09_backlight_board_info, 1);
+
 	return platform_add_devices(kfr2r09_devices,
 				    ARRAY_SIZE(kfr2r09_devices));
 }
diff --git a/arch/sh/include/mach-kfr2r09/mach/kfr2r09.h b/arch/sh/include/mach-kfr2r09/mach/kfr2r09.h
index c20c9e5..79f154e 100644
--- a/arch/sh/include/mach-kfr2r09/mach/kfr2r09.h
+++ b/arch/sh/include/mach-kfr2r09/mach/kfr2r09.h
@@ -4,13 +4,11 @@
 #include <video/sh_mobile_lcdc.h>
 
 #if defined(CONFIG_FB_SH_MOBILE_LCDC) || defined(CONFIG_FB_SH_MOBILE_LCDC_MODULE)
-int kfr2r09_lcd_set_brightness(int brightness);
 int kfr2r09_lcd_setup(void *sys_ops_handle,
 		      struct sh_mobile_lcdc_sys_bus_ops *sys_ops);
 void kfr2r09_lcd_start(void *sys_ops_handle,
 		       struct sh_mobile_lcdc_sys_bus_ops *sys_ops);
 #else
-static int kfr2r09_lcd_set_brightness(int brightness) {}
 static int kfr2r09_lcd_setup(void *sys_ops_handle,
 				struct sh_mobile_lcdc_sys_bus_ops *sys_ops)
 {
diff --git a/drivers/clocksource/bcm_kona_timer.c b/drivers/clocksource/bcm_kona_timer.c
index ba3d859..0d7d8c3 100644
--- a/drivers/clocksource/bcm_kona_timer.c
+++ b/drivers/clocksource/bcm_kona_timer.c
@@ -99,7 +99,8 @@ kona_timer_get_counter(void *timer_base, uint32_t *msw, uint32_t *lsw)
 }
 
 static const struct of_device_id bcm_timer_ids[] __initconst = {
-	{.compatible = "bcm,kona-timer"},
+	{.compatible = "brcm,kona-timer"},
+	{.compatible = "bcm,kona-timer"}, /* deprecated name */
 	{},
 };
 
@@ -201,4 +202,9 @@ static void __init kona_timer_init(struct device_node *node)
 	kona_timer_set_next_event((arch_timer_rate / HZ), NULL);
 }
 
+CLOCKSOURCE_OF_DECLARE(brcm_kona, "brcm,kona-timer", kona_timer_init);
+/*
+ * bcm,kona-timer is deprecated by brcm,kona-timer
+ * being kept here for driver compatibility
+ */
 CLOCKSOURCE_OF_DECLARE(bcm_kona, "bcm,kona-timer", kona_timer_init);
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index e43402d..074bcb3 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -429,18 +429,6 @@ config LEDS_ASIC3
 	  cannot be used. This driver supports hardware blinking with an on+off
 	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
 
-config LEDS_RENESAS_TPU
-	bool "LED support for Renesas TPU"
-	depends on LEDS_CLASS=y && HAVE_CLK && GPIOLIB
-	help
-	  This option enables build of the LED TPU platform driver,
-	  suitable to drive any TPU channel on newer Renesas SoCs.
-	  The driver controls the GPIO pin connected to the LED via
-	  the GPIO framework and expects the LED to be connected to
-	  a pin that can be driven in both GPIO mode and using TPU
-	  pin function. The latter to support brightness control.
-	  Brightness control is supported but hardware blinking is not.
-
 config LEDS_TCA6507
 	tristate "LED Support for TCA6507 I2C chip"
 	depends on LEDS_CLASS && I2C
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index ac28977..ae4b613 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -49,7 +49,6 @@ obj-$(CONFIG_LEDS_MC13783)		+= leds-mc13783.o
 obj-$(CONFIG_LEDS_NS2)			+= leds-ns2.o
 obj-$(CONFIG_LEDS_NETXBIG)		+= leds-netxbig.o
 obj-$(CONFIG_LEDS_ASIC3)		+= leds-asic3.o
-obj-$(CONFIG_LEDS_RENESAS_TPU)		+= leds-renesas-tpu.o
 obj-$(CONFIG_LEDS_MAX8997)		+= leds-max8997.o
 obj-$(CONFIG_LEDS_LM355x)		+= leds-lm355x.o
 obj-$(CONFIG_LEDS_BLINKM)		+= leds-blinkm.o
diff --git a/drivers/leds/leds-renesas-tpu.c b/drivers/leds/leds-renesas-tpu.c
deleted file mode 100644
index adebf49..0000000
--- a/drivers/leds/leds-renesas-tpu.c
+++ /dev/null
@@ -1,337 +0,0 @@
-/*
- * LED control using Renesas TPU
- *
- *  Copyright (C) 2011 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/spinlock.h>
-#include <linux/printk.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/leds.h>
-#include <linux/platform_data/leds-renesas-tpu.h>
-#include <linux/gpio.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/pm_runtime.h>
-#include <linux/workqueue.h>
-
-enum r_tpu_pin { R_TPU_PIN_UNUSED, R_TPU_PIN_GPIO, R_TPU_PIN_GPIO_FN };
-enum r_tpu_timer { R_TPU_TIMER_UNUSED, R_TPU_TIMER_ON };
-
-struct r_tpu_priv {
-	struct led_classdev ldev;
-	void __iomem *mapbase;
-	struct clk *clk;
-	struct platform_device *pdev;
-	enum r_tpu_pin pin_state;
-	enum r_tpu_timer timer_state;
-	unsigned long min_rate;
-	unsigned int refresh_rate;
-	struct work_struct work;
-	enum led_brightness new_brightness;
-};
-
-static DEFINE_SPINLOCK(r_tpu_lock);
-
-#define TSTR -1 /* Timer start register (shared register) */
-#define TCR  0 /* Timer control register (+0x00) */
-#define TMDR 1 /* Timer mode register (+0x04) */
-#define TIOR 2 /* Timer I/O control register (+0x08) */
-#define TIER 3 /* Timer interrupt enable register (+0x0c) */
-#define TSR  4 /* Timer status register (+0x10) */
-#define TCNT 5 /* Timer counter (+0x14) */
-#define TGRA 6 /* Timer general register A (+0x18) */
-#define TGRB 7 /* Timer general register B (+0x1c) */
-#define TGRC 8 /* Timer general register C (+0x20) */
-#define TGRD 9 /* Timer general register D (+0x24) */
-
-static inline u16 r_tpu_read(struct r_tpu_priv *p, int reg_nr)
-{
-	struct led_renesas_tpu_config *cfg = p->pdev->dev.platform_data;
-	void __iomem *base = p->mapbase;
-	unsigned long offs = reg_nr << 2;
-
-	if (reg_nr == TSTR)
-		return ioread16(base - cfg->channel_offset);
-
-	return ioread16(base + offs);
-}
-
-static inline void r_tpu_write(struct r_tpu_priv *p, int reg_nr, u16 value)
-{
-	struct led_renesas_tpu_config *cfg = p->pdev->dev.platform_data;
-	void __iomem *base = p->mapbase;
-	unsigned long offs = reg_nr << 2;
-
-	if (reg_nr == TSTR) {
-		iowrite16(value, base - cfg->channel_offset);
-		return;
-	}
-
-	iowrite16(value, base + offs);
-}
-
-static void r_tpu_start_stop_ch(struct r_tpu_priv *p, int start)
-{
-	struct led_renesas_tpu_config *cfg = p->pdev->dev.platform_data;
-	unsigned long flags;
-	u16 value;
-
-	/* start stop register shared by multiple timer channels */
-	spin_lock_irqsave(&r_tpu_lock, flags);
-	value = r_tpu_read(p, TSTR);
-
-	if (start)
-		value |= 1 << cfg->timer_bit;
-	else
-		value &= ~(1 << cfg->timer_bit);
-
-	r_tpu_write(p, TSTR, value);
-	spin_unlock_irqrestore(&r_tpu_lock, flags);
-}
-
-static int r_tpu_enable(struct r_tpu_priv *p, enum led_brightness brightness)
-{
-	struct led_renesas_tpu_config *cfg = p->pdev->dev.platform_data;
-	int prescaler[] = { 1, 4, 16, 64 };
-	int k, ret;
-	unsigned long rate, tmp;
-
-	if (p->timer_state == R_TPU_TIMER_ON)
-		return 0;
-
-	/* wake up device and enable clock */
-	pm_runtime_get_sync(&p->pdev->dev);
-	ret = clk_enable(p->clk);
-	if (ret) {
-		dev_err(&p->pdev->dev, "cannot enable clock\n");
-		return ret;
-	}
-
-	/* make sure channel is disabled */
-	r_tpu_start_stop_ch(p, 0);
-
-	/* get clock rate after enabling it */
-	rate = clk_get_rate(p->clk);
-
-	/* pick the lowest acceptable rate */
-	for (k = ARRAY_SIZE(prescaler) - 1; k >= 0; k--)
-		if ((rate / prescaler[k]) >= p->min_rate)
-			break;
-
-	if (k < 0) {
-		dev_err(&p->pdev->dev, "clock rate mismatch\n");
-		goto err0;
-	}
-	dev_dbg(&p->pdev->dev, "rate = %lu, prescaler %u\n",
-		rate, prescaler[k]);
-
-	/* clear TCNT on TGRB match, count on rising edge, set prescaler */
-	r_tpu_write(p, TCR, 0x0040 | k);
-
-	/* output 0 until TGRA, output 1 until TGRB */
-	r_tpu_write(p, TIOR, 0x0002);
-
-	rate /= prescaler[k] * p->refresh_rate;
-	r_tpu_write(p, TGRB, rate);
-	dev_dbg(&p->pdev->dev, "TRGB = 0x%04lx\n", rate);
-
-	tmp = (cfg->max_brightness - brightness) * rate;
-	r_tpu_write(p, TGRA, tmp / cfg->max_brightness);
-	dev_dbg(&p->pdev->dev, "TRGA = 0x%04lx\n", tmp / cfg->max_brightness);
-
-	/* PWM mode */
-	r_tpu_write(p, TMDR, 0x0002);
-
-	/* enable channel */
-	r_tpu_start_stop_ch(p, 1);
-
-	p->timer_state = R_TPU_TIMER_ON;
-	return 0;
- err0:
-	clk_disable(p->clk);
-	pm_runtime_put_sync(&p->pdev->dev);
-	return -ENOTSUPP;
-}
-
-static void r_tpu_disable(struct r_tpu_priv *p)
-{
-	if (p->timer_state == R_TPU_TIMER_UNUSED)
-		return;
-
-	/* disable channel */
-	r_tpu_start_stop_ch(p, 0);
-
-	/* stop clock and mark device as idle */
-	clk_disable(p->clk);
-	pm_runtime_put_sync(&p->pdev->dev);
-
-	p->timer_state = R_TPU_TIMER_UNUSED;
-}
-
-static void r_tpu_set_pin(struct r_tpu_priv *p, enum r_tpu_pin new_state,
-			  enum led_brightness brightness)
-{
-	struct led_renesas_tpu_config *cfg = p->pdev->dev.platform_data;
-
-	if (p->pin_state == new_state) {
-		if (p->pin_state == R_TPU_PIN_GPIO)
-			gpio_set_value(cfg->pin_gpio, brightness);
-		return;
-	}
-
-	if (p->pin_state == R_TPU_PIN_GPIO)
-		gpio_free(cfg->pin_gpio);
-
-	if (p->pin_state == R_TPU_PIN_GPIO_FN)
-		gpio_free(cfg->pin_gpio_fn);
-
-	if (new_state == R_TPU_PIN_GPIO)
-		gpio_request_one(cfg->pin_gpio, !!brightness ?
-				GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW,
-				cfg->name);
-
-	if (new_state == R_TPU_PIN_GPIO_FN)
-		gpio_request(cfg->pin_gpio_fn, cfg->name);
-
-	p->pin_state = new_state;
-}
-
-static void r_tpu_work(struct work_struct *work)
-{
-	struct r_tpu_priv *p = container_of(work, struct r_tpu_priv, work);
-	enum led_brightness brightness = p->new_brightness;
-
-	r_tpu_disable(p);
-
-	/* off and maximum are handled as GPIO pins, in between PWM */
-	if ((brightness == 0) || (brightness == p->ldev.max_brightness))
-		r_tpu_set_pin(p, R_TPU_PIN_GPIO, brightness);
-	else {
-		r_tpu_set_pin(p, R_TPU_PIN_GPIO_FN, 0);
-		r_tpu_enable(p, brightness);
-	}
-}
-
-static void r_tpu_set_brightness(struct led_classdev *ldev,
-				 enum led_brightness brightness)
-{
-	struct r_tpu_priv *p = container_of(ldev, struct r_tpu_priv, ldev);
-	p->new_brightness = brightness;
-	schedule_work(&p->work);
-}
-
-static int r_tpu_probe(struct platform_device *pdev)
-{
-	struct led_renesas_tpu_config *cfg = pdev->dev.platform_data;
-	struct r_tpu_priv *p;
-	struct resource *res;
-	int ret;
-
-	if (!cfg) {
-		dev_err(&pdev->dev, "missing platform data\n");
-		return -ENODEV;
-	}
-
-	p = devm_kzalloc(&pdev->dev, sizeof(*p), GFP_KERNEL);
-	if (p == NULL) {
-		dev_err(&pdev->dev, "failed to allocate driver data\n");
-		return -ENOMEM;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "failed to get I/O memory\n");
-		return -ENXIO;
-	}
-
-	/* map memory, let mapbase point to our channel */
-	p->mapbase = devm_ioremap_nocache(&pdev->dev, res->start,
-					resource_size(res));
-	if (p->mapbase == NULL) {
-		dev_err(&pdev->dev, "failed to remap I/O memory\n");
-		return -ENXIO;
-	}
-
-	/* get hold of clock */
-	p->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(p->clk)) {
-		dev_err(&pdev->dev, "cannot get clock\n");
-		return PTR_ERR(p->clk);
-	}
-
-	p->pdev = pdev;
-	p->pin_state = R_TPU_PIN_UNUSED;
-	p->timer_state = R_TPU_TIMER_UNUSED;
-	p->refresh_rate = cfg->refresh_rate ? cfg->refresh_rate : 100;
-	r_tpu_set_pin(p, R_TPU_PIN_GPIO, LED_OFF);
-	platform_set_drvdata(pdev, p);
-
-	INIT_WORK(&p->work, r_tpu_work);
-
-	p->ldev.name = cfg->name;
-	p->ldev.brightness = LED_OFF;
-	p->ldev.max_brightness = cfg->max_brightness;
-	p->ldev.brightness_set = r_tpu_set_brightness;
-	p->ldev.flags |= LED_CORE_SUSPENDRESUME;
-	ret = led_classdev_register(&pdev->dev, &p->ldev);
-	if (ret < 0)
-		goto err0;
-
-	/* max_brightness may be updated by the LED core code */
-	p->min_rate = p->ldev.max_brightness * p->refresh_rate;
-
-	pm_runtime_enable(&pdev->dev);
-	return 0;
-
- err0:
-	r_tpu_set_pin(p, R_TPU_PIN_UNUSED, LED_OFF);
-	return ret;
-}
-
-static int r_tpu_remove(struct platform_device *pdev)
-{
-	struct r_tpu_priv *p = platform_get_drvdata(pdev);
-
-	r_tpu_set_brightness(&p->ldev, LED_OFF);
-	led_classdev_unregister(&p->ldev);
-	cancel_work_sync(&p->work);
-	r_tpu_disable(p);
-	r_tpu_set_pin(p, R_TPU_PIN_UNUSED, LED_OFF);
-
-	pm_runtime_disable(&pdev->dev);
-
-	return 0;
-}
-
-static struct platform_driver r_tpu_device_driver = {
-	.probe		= r_tpu_probe,
-	.remove		= r_tpu_remove,
-	.driver		= {
-		.name	= "leds-renesas-tpu",
-	}
-};
-
-module_platform_driver(r_tpu_device_driver);
-
-MODULE_AUTHOR("Magnus Damm");
-MODULE_DESCRIPTION("Renesas TPU LED Driver");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/mmc/host/sdhci-bcm-kona.c b/drivers/mmc/host/sdhci-bcm-kona.c
index 87175f9..85472d3 100644
--- a/drivers/mmc/host/sdhci-bcm-kona.c
+++ b/drivers/mmc/host/sdhci-bcm-kona.c
@@ -24,7 +24,6 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_gpio.h>
-#include <linux/version.h>
 #include <linux/mmc/slot-gpio.h>
 
 #include "sdhci-pltfm.h"
@@ -162,7 +161,7 @@ static int sdhci_bcm_kona_sd_card_emulate(struct sdhci_host *host, int insert)
 /*
  * SD card interrupt event callback
  */
-void sdhci_bcm_kona_card_event(struct sdhci_host *host)
+static void sdhci_bcm_kona_card_event(struct sdhci_host *host)
 {
 	if (mmc_gpio_get_cd(host->mmc) > 0) {
 		dev_dbg(mmc_dev(host->mmc),
@@ -221,13 +220,14 @@ static struct sdhci_pltfm_data sdhci_pltfm_data_kona = {
 		SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
 };
 
-static const struct of_device_id sdhci_bcm_kona_of_match[] __initdata = {
-	{ .compatible = "bcm,kona-sdhci"},
+static struct __initconst of_device_id sdhci_bcm_kona_of_match[] = {
+	{ .compatible = "brcm,kona-sdhci"},
+	{ .compatible = "bcm,kona-sdhci"}, /* deprecated name */
 	{}
 };
 MODULE_DEVICE_TABLE(of, sdhci_bcm_kona_of_match);
 
-static int __init sdhci_bcm_kona_probe(struct platform_device *pdev)
+static int sdhci_bcm_kona_probe(struct platform_device *pdev)
 {
 	struct sdhci_bcm_kona_dev *kona_dev = NULL;
 	struct sdhci_pltfm_host *pltfm_priv;
@@ -263,7 +263,7 @@ static int __init sdhci_bcm_kona_probe(struct platform_device *pdev)
 		(mmc_gpio_get_cd(host->mmc) != -ENOSYS) ? 'Y' : 'N',
 		(mmc_gpio_get_ro(host->mmc) != -ENOSYS) ? 'Y' : 'N');
 
-	if (host->mmc->caps | MMC_CAP_NONREMOVABLE)
+	if (host->mmc->caps & MMC_CAP_NONREMOVABLE)
 		host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
 
 	dev_dbg(dev, "is_8bit=%c\n",
@@ -282,7 +282,7 @@ static int __init sdhci_bcm_kona_probe(struct platform_device *pdev)
 	}
 
 	/* if device is eMMC, emulate card insert right here */
-	if (host->mmc->caps | MMC_CAP_NONREMOVABLE) {
+	if (host->mmc->caps & MMC_CAP_NONREMOVABLE) {
 		ret = sdhci_bcm_kona_sd_card_emulate(host, 1);
 		if (ret) {
 			dev_err(dev,
@@ -336,10 +336,10 @@ static struct platform_driver sdhci_bcm_kona_driver = {
 		.name	= "sdhci-kona",
 		.owner	= THIS_MODULE,
 		.pm	= SDHCI_PLTFM_PMOPS,
-		.of_match_table = of_match_ptr(sdhci_bcm_kona_of_match),
+		.of_match_table = sdhci_bcm_kona_of_match,
 	},
 	.probe		= sdhci_bcm_kona_probe,
-	.remove		= __exit_p(sdhci_bcm_kona_remove),
+	.remove		= sdhci_bcm_kona_remove,
 };
 module_platform_driver(sdhci_bcm_kona_driver);
 
diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
index d5ab658..d4a7a35 100644
--- a/drivers/video/backlight/Kconfig
+++ b/drivers/video/backlight/Kconfig
@@ -425,6 +425,25 @@ config BACKLIGHT_AS3711
 	  If you have an Austrian Microsystems AS3711 say Y to enable the
 	  backlight driver.
 
+config BACKLIGHT_GPIO
+	tristate "Generic GPIO based Backlight Driver"
+	depends on GPIOLIB
+	help
+	  If you have a LCD backlight adjustable by GPIO, say Y to enable
+	  this driver.
+
+config BACKLIGHT_LV5207LP
+	tristate "Sanyo LV5207LP Backlight"
+	depends on I2C
+	help
+	  If you have a Sanyo LV5207LP say Y to enable the backlight driver.
+
+config BACKLIGHT_BD6107
+	tristate "Rohm BD6107 Backlight"
+	depends on I2C
+	help
+	  If you have a Rohm BD6107 say Y to enable the backlight driver.
+
 endif # BACKLIGHT_CLASS_DEVICE
 
 endif # BACKLIGHT_LCD_SUPPORT
diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
index 92711fe..38e1bab 100644
--- a/drivers/video/backlight/Makefile
+++ b/drivers/video/backlight/Makefile
@@ -26,12 +26,14 @@ obj-$(CONFIG_BACKLIGHT_ADP8870)		+= adp8870_bl.o
 obj-$(CONFIG_BACKLIGHT_APPLE)		+= apple_bl.o
 obj-$(CONFIG_BACKLIGHT_AS3711)		+= as3711_bl.o
 obj-$(CONFIG_BACKLIGHT_ATMEL_PWM)	+= atmel-pwm-bl.o
+obj-$(CONFIG_BACKLIGHT_BD6107)		+= bd6107.o
 obj-$(CONFIG_BACKLIGHT_CARILLO_RANCH)	+= cr_bllcd.o
 obj-$(CONFIG_BACKLIGHT_CLASS_DEVICE)	+= backlight.o
 obj-$(CONFIG_BACKLIGHT_DA903X)		+= da903x_bl.o
 obj-$(CONFIG_BACKLIGHT_DA9052)		+= da9052_bl.o
 obj-$(CONFIG_BACKLIGHT_EP93XX)		+= ep93xx_bl.o
 obj-$(CONFIG_BACKLIGHT_GENERIC)		+= generic_bl.o
+obj-$(CONFIG_BACKLIGHT_GPIO)		+= gpio_backlight.o
 obj-$(CONFIG_BACKLIGHT_HP680)		+= hp680_bl.o
 obj-$(CONFIG_BACKLIGHT_HP700)		+= jornada720_bl.o
 obj-$(CONFIG_BACKLIGHT_LM3533)		+= lm3533_bl.o
@@ -40,6 +42,7 @@ obj-$(CONFIG_BACKLIGHT_LM3639)		+= lm3639_bl.o
 obj-$(CONFIG_BACKLIGHT_LOCOMO)		+= locomolcd.o
 obj-$(CONFIG_BACKLIGHT_LP855X)		+= lp855x_bl.o
 obj-$(CONFIG_BACKLIGHT_LP8788)		+= lp8788_bl.o
+obj-$(CONFIG_BACKLIGHT_LV5207LP)	+= lv5207lp.o
 obj-$(CONFIG_BACKLIGHT_MAX8925)		+= max8925_bl.o
 obj-$(CONFIG_BACKLIGHT_OMAP1)		+= omap1_bl.o
 obj-$(CONFIG_BACKLIGHT_OT200)		+= ot200_bl.o
diff --git a/drivers/video/backlight/bd6107.c b/drivers/video/backlight/bd6107.c
new file mode 100644
index 0000000..15e3294
--- /dev/null
+++ b/drivers/video/backlight/bd6107.c
@@ -0,0 +1,213 @@
+/*
+ * ROHM Semiconductor BD6107 LED Driver
+ *
+ * Copyright (C) 2013 Ideas on board SPRL
+ *
+ * Contact: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/platform_data/bd6107.h>
+#include <linux/slab.h>
+
+#define BD6107_PSCNT1				0x00
+#define BD6107_PSCNT1_PSCNTREG2			(1 << 2)
+#define BD6107_PSCNT1_PSCNTREG1			(1 << 0)
+#define BD6107_REGVSET				0x02
+#define BD6107_REGVSET_REG1VSET_2_85V		(1 << 2)
+#define BD6107_REGVSET_REG1VSET_2_80V		(0 << 2)
+#define BD6107_LEDCNT1				0x03
+#define BD6107_LEDCNT1_LEDONOFF2		(1 << 1)
+#define BD6107_LEDCNT1_LEDONOFF1		(1 << 0)
+#define BD6107_PORTSEL				0x04
+#define BD6107_PORTSEL_LEDM(n)			(1 << (n))
+#define BD6107_RGB1CNT1				0x05
+#define BD6107_RGB1CNT2				0x06
+#define BD6107_RGB1CNT3				0x07
+#define BD6107_RGB1CNT4				0x08
+#define BD6107_RGB1CNT5				0x09
+#define BD6107_RGB1FLM				0x0a
+#define BD6107_RGB2CNT1				0x0b
+#define BD6107_RGB2CNT2				0x0c
+#define BD6107_RGB2CNT3				0x0d
+#define BD6107_RGB2CNT4				0x0e
+#define BD6107_RGB2CNT5				0x0f
+#define BD6107_RGB2FLM				0x10
+#define BD6107_PSCONT3				0x11
+#define BD6107_SMMONCNT				0x12
+#define BD6107_DCDCCNT				0x13
+#define BD6107_IOSEL				0x14
+#define BD6107_OUT1				0x15
+#define BD6107_OUT2				0x16
+#define BD6107_MASK1				0x17
+#define BD6107_MASK2				0x18
+#define BD6107_FACTOR1				0x19
+#define BD6107_FACTOR2				0x1a
+#define BD6107_CLRFACT1				0x1b
+#define BD6107_CLRFACT2				0x1c
+#define BD6107_STATE1				0x1d
+#define BD6107_LSIVER				0x1e
+#define BD6107_GRPSEL				0x1f
+#define BD6107_LEDCNT2				0x20
+#define BD6107_LEDCNT3				0x21
+#define BD6107_MCURRENT				0x22
+#define BD6107_MAINCNT1				0x23
+#define BD6107_MAINCNT2				0x24
+#define BD6107_SLOPECNT				0x25
+#define BD6107_MSLOPE				0x26
+#define BD6107_RGBSLOPE				0x27
+#define BD6107_TEST				0x29
+#define BD6107_SFTRST				0x2a
+#define BD6107_SFTRSTGD				0x2b
+
+struct bd6107 {
+	struct i2c_client *client;
+	struct backlight_device *backlight;
+	struct bd6107_platform_data *pdata;
+};
+
+static int bd6107_write(struct bd6107 *bd, u8 reg, u8 data)
+{
+	return i2c_smbus_write_byte_data(bd->client, reg, data);
+}
+
+static int bd6107_backlight_update_status(struct backlight_device *backlight)
+{
+	struct bd6107 *bd = bl_get_data(backlight);
+	int brightness = backlight->props.brightness;
+
+	if (backlight->props.power != FB_BLANK_UNBLANK ||
+	    backlight->props.fb_blank != FB_BLANK_UNBLANK ||
+	    backlight->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
+		brightness = 0;
+
+	if (brightness) {
+		bd6107_write(bd, BD6107_PORTSEL, BD6107_PORTSEL_LEDM(2) |
+			     BD6107_PORTSEL_LEDM(1) | BD6107_PORTSEL_LEDM(0));
+		bd6107_write(bd, BD6107_MAINCNT1, brightness);
+		bd6107_write(bd, BD6107_LEDCNT1, BD6107_LEDCNT1_LEDONOFF1);
+	} else {
+		gpio_set_value(bd->pdata->reset, 0);
+		msleep(24);
+		gpio_set_value(bd->pdata->reset, 1);
+	}
+
+	return 0;
+}
+
+static int bd6107_backlight_get_brightness(struct backlight_device *backlight)
+{
+	return backlight->props.brightness;
+}
+
+static int bd6107_backlight_check_fb(struct backlight_device *backlight,
+				       struct fb_info *info)
+{
+	struct bd6107 *bd = bl_get_data(backlight);
+
+	return bd->pdata->fbdev == NULL || bd->pdata->fbdev == info->dev;
+}
+
+static const struct backlight_ops bd6107_backlight_ops = {
+	.options	= BL_CORE_SUSPENDRESUME,
+	.update_status	= bd6107_backlight_update_status,
+	.get_brightness	= bd6107_backlight_get_brightness,
+	.check_fb	= bd6107_backlight_check_fb,
+};
+
+static int bd6107_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct bd6107_platform_data *pdata = client->dev.platform_data;
+	struct backlight_device *backlight;
+	struct backlight_properties props;
+	struct bd6107 *bd;
+	int ret;
+
+	if (pdata == NULL || !pdata->reset) {
+		dev_err(&client->dev, "No reset GPIO in platform data\n");
+		return -EINVAL;
+	}
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA)) {
+		dev_warn(&client->dev,
+			 "I2C adapter doesn't support I2C_FUNC_SMBUS_BYTE\n");
+		return -EIO;
+	}
+
+	bd = devm_kzalloc(&client->dev, sizeof(*bd), GFP_KERNEL);
+	if (!bd)
+		return -ENOMEM;
+
+	bd->client = client;
+	bd->pdata = pdata;
+
+	ret = devm_gpio_request_one(&client->dev, pdata->reset,
+				    GPIOF_DIR_OUT | GPIOF_INIT_LOW, "reset");
+	if (ret < 0) {
+		dev_err(&client->dev, "unable to request reset GPIO\n");
+		return ret;
+	}
+
+	memset(&props, 0, sizeof(props));
+	props.type = BACKLIGHT_RAW;
+	props.max_brightness = 128;
+	props.brightness = clamp_t(unsigned int, pdata->def_value, 0,
+				   props.max_brightness);
+
+	backlight = backlight_device_register(dev_name(&client->dev),
+					      &bd->client->dev, bd,
+					      &bd6107_backlight_ops, &props);
+	if (IS_ERR(backlight)) {
+		dev_err(&client->dev, "failed to register backlight\n");
+		return PTR_ERR(backlight);
+	}
+
+	backlight_update_status(backlight);
+	i2c_set_clientdata(client, backlight);
+
+	return 0;
+}
+
+static int bd6107_remove(struct i2c_client *client)
+{
+	struct backlight_device *backlight = i2c_get_clientdata(client);
+
+	backlight->props.brightness = 0;
+	backlight_update_status(backlight);
+	backlight_device_unregister(backlight);
+
+	return 0;
+}
+
+static const struct i2c_device_id bd6107_ids[] = {
+	{ "bd6107", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, bd6107_ids);
+
+static struct i2c_driver bd6107_driver = {
+	.driver = {
+		.name = "bd6107",
+	},
+	.probe = bd6107_probe,
+	.remove = bd6107_remove,
+	.id_table = bd6107_ids,
+};
+
+module_i2c_driver(bd6107_driver);
+
+MODULE_DESCRIPTION("Rohm BD6107 Backlight Driver");
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/video/backlight/gpio_backlight.c b/drivers/video/backlight/gpio_backlight.c
new file mode 100644
index 0000000..5fa217f
--- /dev/null
+++ b/drivers/video/backlight/gpio_backlight.c
@@ -0,0 +1,133 @@
+/*
+ * gpio_backlight.c - Simple GPIO-controlled backlight
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/backlight.h>
+#include <linux/err.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_data/gpio_backlight.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+struct gpio_backlight {
+	struct device *dev;
+	struct device *fbdev;
+
+	int gpio;
+	int active;
+};
+
+static int gpio_backlight_update_status(struct backlight_device *bl)
+{
+	struct gpio_backlight *gbl = bl_get_data(bl);
+	int brightness = bl->props.brightness;
+
+	if (bl->props.power != FB_BLANK_UNBLANK ||
+	    bl->props.fb_blank != FB_BLANK_UNBLANK ||
+	    bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
+		brightness = 0;
+
+	gpio_set_value(gbl->gpio, brightness ? gbl->active : !gbl->active);
+
+	return 0;
+}
+
+static int gpio_backlight_get_brightness(struct backlight_device *bl)
+{
+	return bl->props.brightness;
+}
+
+static int gpio_backlight_check_fb(struct backlight_device *bl,
+				   struct fb_info *info)
+{
+	struct gpio_backlight *gbl = bl_get_data(bl);
+
+	return gbl->fbdev == NULL || gbl->fbdev == info->dev;
+}
+
+static const struct backlight_ops gpio_backlight_ops = {
+	.options	= BL_CORE_SUSPENDRESUME,
+	.update_status	= gpio_backlight_update_status,
+	.get_brightness	= gpio_backlight_get_brightness,
+	.check_fb	= gpio_backlight_check_fb,
+};
+
+static int gpio_backlight_probe(struct platform_device *pdev)
+{
+	struct gpio_backlight_platform_data *pdata = pdev->dev.platform_data;
+	struct backlight_properties props;
+	struct backlight_device *bl;
+	struct gpio_backlight *gbl;
+	int ret;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "failed to find platform data\n");
+		return -ENODEV;
+	}
+
+	gbl = devm_kzalloc(&pdev->dev, sizeof(*gbl), GFP_KERNEL);
+	if (gbl == NULL)
+		return -ENOMEM;
+
+	gbl->dev = &pdev->dev;
+	gbl->fbdev = pdata->fbdev;
+	gbl->gpio = pdata->gpio;
+	gbl->active = pdata->active_low ? 0 : 1;
+
+	ret = devm_gpio_request_one(gbl->dev, gbl->gpio, GPIOF_DIR_OUT |
+				    (gbl->active ? GPIOF_INIT_LOW
+						 : GPIOF_INIT_HIGH),
+				    pdata->name);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "unable to request GPIO\n");
+		return ret;
+	}
+
+	memset(&props, 0, sizeof(props));
+	props.type = BACKLIGHT_RAW;
+	props.max_brightness = 1;
+	bl = backlight_device_register(dev_name(&pdev->dev), &pdev->dev, gbl,
+				       &gpio_backlight_ops, &props);
+	if (IS_ERR(bl)) {
+		dev_err(&pdev->dev, "failed to register backlight\n");
+		return PTR_ERR(bl);
+	}
+
+	bl->props.brightness = pdata->def_value;
+	backlight_update_status(bl);
+
+	platform_set_drvdata(pdev, bl);
+	return 0;
+}
+
+static int gpio_backlight_remove(struct platform_device *pdev)
+{
+	struct backlight_device *bl = platform_get_drvdata(pdev);
+
+	backlight_device_unregister(bl);
+	return 0;
+}
+
+static struct platform_driver gpio_backlight_driver = {
+	.driver		= {
+		.name		= "gpio-backlight",
+		.owner		= THIS_MODULE,
+	},
+	.probe		= gpio_backlight_probe,
+	.remove		= gpio_backlight_remove,
+};
+
+module_platform_driver(gpio_backlight_driver);
+
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_DESCRIPTION("GPIO-based Backlight Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:gpio-backlight");
diff --git a/drivers/video/backlight/lv5207lp.c b/drivers/video/backlight/lv5207lp.c
new file mode 100644
index 0000000..498fd73
--- /dev/null
+++ b/drivers/video/backlight/lv5207lp.c
@@ -0,0 +1,171 @@
+/*
+ * Sanyo LV5207LP LED Driver
+ *
+ * Copyright (C) 2013 Ideas on board SPRL
+ *
+ * Contact: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/backlight.h>
+#include <linux/err.h>
+#include <linux/fb.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/platform_data/lv5207lp.h>
+#include <linux/slab.h>
+
+#define LV5207LP_CTRL1			0x00
+#define LV5207LP_CPSW			(1 << 7)
+#define LV5207LP_SCTEN			(1 << 6)
+#define LV5207LP_C10			(1 << 5)
+#define LV5207LP_CKSW			(1 << 4)
+#define LV5207LP_RSW			(1 << 3)
+#define LV5207LP_GSW			(1 << 2)
+#define LV5207LP_BSW			(1 << 1)
+#define LV5207LP_CTRL2			0x01
+#define LV5207LP_MSW			(1 << 7)
+#define LV5207LP_MLED4			(1 << 6)
+#define LV5207LP_RED			0x02
+#define LV5207LP_GREEN			0x03
+#define LV5207LP_BLUE			0x04
+
+#define LV5207LP_MAX_BRIGHTNESS		32
+
+struct lv5207lp {
+	struct i2c_client *client;
+	struct backlight_device *backlight;
+	struct lv5207lp_platform_data *pdata;
+};
+
+static int lv5207lp_write(struct lv5207lp *lv, u8 reg, u8 data)
+{
+	return i2c_smbus_write_byte_data(lv->client, reg, data);
+}
+
+static int lv5207lp_backlight_update_status(struct backlight_device *backlight)
+{
+	struct lv5207lp *lv = bl_get_data(backlight);
+	int brightness = backlight->props.brightness;
+
+	if (backlight->props.power != FB_BLANK_UNBLANK ||
+	    backlight->props.fb_blank != FB_BLANK_UNBLANK ||
+	    backlight->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
+		brightness = 0;
+
+	if (brightness) {
+		lv5207lp_write(lv, LV5207LP_CTRL1,
+			       LV5207LP_CPSW | LV5207LP_C10 | LV5207LP_CKSW);
+		lv5207lp_write(lv, LV5207LP_CTRL2,
+			       LV5207LP_MSW | LV5207LP_MLED4 |
+			       (brightness - 1));
+	} else {
+		lv5207lp_write(lv, LV5207LP_CTRL1, 0);
+		lv5207lp_write(lv, LV5207LP_CTRL2, 0);
+	}
+
+	return 0;
+}
+
+static int lv5207lp_backlight_get_brightness(struct backlight_device *backlight)
+{
+	return backlight->props.brightness;
+}
+
+static int lv5207lp_backlight_check_fb(struct backlight_device *backlight,
+				       struct fb_info *info)
+{
+	struct lv5207lp *lv = bl_get_data(backlight);
+
+	return lv->pdata->fbdev == NULL || lv->pdata->fbdev == info->dev;
+}
+
+static const struct backlight_ops lv5207lp_backlight_ops = {
+	.options	= BL_CORE_SUSPENDRESUME,
+	.update_status	= lv5207lp_backlight_update_status,
+	.get_brightness	= lv5207lp_backlight_get_brightness,
+	.check_fb	= lv5207lp_backlight_check_fb,
+};
+
+static int lv5207lp_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct lv5207lp_platform_data *pdata = client->dev.platform_data;
+	struct backlight_device *backlight;
+	struct backlight_properties props;
+	struct lv5207lp *lv;
+
+	if (pdata == NULL) {
+		dev_err(&client->dev, "No platform data supplied\n");
+		return -EINVAL;
+	}
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA)) {
+		dev_warn(&client->dev,
+			 "I2C adapter doesn't support I2C_FUNC_SMBUS_BYTE\n");
+		return -EIO;
+	}
+
+	lv = devm_kzalloc(&client->dev, sizeof(*lv), GFP_KERNEL);
+	if (!lv)
+		return -ENOMEM;
+
+	lv->client = client;
+	lv->pdata = pdata;
+
+	memset(&props, 0, sizeof(props));
+	props.type = BACKLIGHT_RAW;
+	props.max_brightness = min_t(unsigned int, pdata->max_value,
+				     LV5207LP_MAX_BRIGHTNESS);
+	props.brightness = clamp_t(unsigned int, pdata->def_value, 0,
+				   props.max_brightness);
+
+	backlight = backlight_device_register(dev_name(&client->dev),
+					      &lv->client->dev, lv,
+					      &lv5207lp_backlight_ops, &props);
+	if (IS_ERR(backlight)) {
+		dev_err(&client->dev, "failed to register backlight\n");
+		return PTR_ERR(backlight);
+	}
+
+	backlight_update_status(backlight);
+	i2c_set_clientdata(client, backlight);
+
+	return 0;
+}
+
+static int lv5207lp_remove(struct i2c_client *client)
+{
+	struct backlight_device *backlight = i2c_get_clientdata(client);
+
+	backlight->props.brightness = 0;
+	backlight_update_status(backlight);
+	backlight_device_unregister(backlight);
+
+	return 0;
+}
+
+static const struct i2c_device_id lv5207lp_ids[] = {
+	{ "lv5207lp", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, lv5207lp_ids);
+
+static struct i2c_driver lv5207lp_driver = {
+	.driver = {
+		.name = "lv5207lp",
+	},
+	.probe = lv5207lp_probe,
+	.remove = lv5207lp_remove,
+	.id_table = lv5207lp_ids,
+};
+
+module_i2c_driver(lv5207lp_driver);
+
+MODULE_DESCRIPTION("Sanyo LV5207LP Backlight Driver");
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/platform_data/bd6107.h b/include/linux/platform_data/bd6107.h
new file mode 100644
index 0000000..671d650
--- /dev/null
+++ b/include/linux/platform_data/bd6107.h
@@ -0,0 +1,19 @@
+/*
+ * bd6107.h - Rohm BD6107 LEDs Driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __BD6107_H__
+#define __BD6107_H__
+
+struct device;
+
+struct bd6107_platform_data {
+	struct device *fbdev;
+	int reset;			/* Reset GPIO */
+	unsigned int def_value;
+};
+
+#endif
diff --git a/include/linux/platform_data/gpio_backlight.h b/include/linux/platform_data/gpio_backlight.h
new file mode 100644
index 0000000..5ae0d9c
--- /dev/null
+++ b/include/linux/platform_data/gpio_backlight.h
@@ -0,0 +1,21 @@
+/*
+ * gpio_backlight.h - Simple GPIO-controlled backlight
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __GPIO_BACKLIGHT_H__
+#define __GPIO_BACKLIGHT_H__
+
+struct device;
+
+struct gpio_backlight_platform_data {
+	struct device *fbdev;
+	int gpio;
+	int def_value;
+	bool active_low;
+	const char *name;
+};
+
+#endif
diff --git a/include/linux/platform_data/leds-renesas-tpu.h b/include/linux/platform_data/leds-renesas-tpu.h
deleted file mode 100644
index 0553870..0000000
--- a/include/linux/platform_data/leds-renesas-tpu.h
+++ /dev/null
@@ -1,14 +0,0 @@
-#ifndef __LEDS_RENESAS_TPU_H__
-#define __LEDS_RENESAS_TPU_H__
-
-struct led_renesas_tpu_config {
-	char *name;
-	unsigned pin_gpio_fn;
-	unsigned pin_gpio;
-	unsigned int channel_offset;
-	unsigned int timer_bit;
-	unsigned int max_brightness;
-	unsigned int refresh_rate;
-};
-
-#endif /* __LEDS_RENESAS_TPU_H__ */
diff --git a/include/linux/platform_data/lv5207lp.h b/include/linux/platform_data/lv5207lp.h
new file mode 100644
index 0000000..7dc4d9a
--- /dev/null
+++ b/include/linux/platform_data/lv5207lp.h
@@ -0,0 +1,19 @@
+/*
+ * lv5207lp.h - Sanyo LV5207LP LEDs Driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __LV5207LP_H__
+#define __LV5207LP_H__
+
+struct device;
+
+struct lv5207lp_platform_data {
+	struct device *fbdev;
+	unsigned int max_value;
+	unsigned int def_value;
+};
+
+#endif