Merge tag 'staging-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging tree merge from Greg KH:
 "Here's the bit staging tree pull request for 3.12-rc1.

  Lots of staging driver updates, and fixes.  Lustre is finally enabled
  in the build, and lots of cleanup started happening in it.  There's a
  new wireless driver in here, and 2 new TTY drivers, which cause the
  overall lines added/removed to be quite large on the "added" side.

  The IIO driver updates are also coming through here, as they are tied
  to the staging iio drivers"

* tag 'staging-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (942 commits)
  staging: dwc2: make dwc2_core_params documentation more complete
  staging: dwc2: validate the value for phy_utmi_width
  staging: dwc2: interpret all hwcfg and related register at init time
  staging: dwc2: properly mask the GRXFSIZ register
  staging: dwc2: remove redundant register reads
  staging: dwc2: re-use hptxfsiz variable
  staging: dwc2: simplify debug output in dwc_hc_init
  staging: dwc2: add missing shift
  staging: dwc2: simplify register shift expressions
  staging: dwc2: only read the snpsid register once
  staging: dwc2: unshift non-bool register value constants
  staging: dwc2: fix off-by-one in check for max_packet_count parameter
  staging: dwc2: remove specific fifo size constants
  Staging:BCM:DDRInit.c:Renaming __FUNCTION__
  staging: bcm: remove Version.h file.
  staging: rtl8188eu: off by one in rtw_set_802_11_add_wep()
  staging: r8188eu: copying one byte too much
  staging: rtl8188eu: || vs && typo
  staging: r8188eu: off by one bugs
  staging: crystalhd: Resolve sparse 'different base types' warnings.
  ...

9 files changed, 93 insertions, 14 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index dda81ff..39c8de0 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -351,6 +351,7 @@ Description:
 		6kohm_to_gnd: connected to ground via a 6kOhm resistor,
 		20kohm_to_gnd: connected to ground via a 20kOhm resistor,
 		100kohm_to_gnd: connected to ground via an 100kOhm resistor,
+		500kohm_to_gnd: connected to ground via a 500kOhm resistor,
 		three_state: left floating.
 		For a list of available output power down options read
 		outX_powerdown_mode_available. If Y is not present the
@@ -792,3 +793,21 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		This attribute is used to read the amount of quadrature error
 		present in the device at a given time.
+
+What:		/sys/.../iio:deviceX/in_accelX_power_mode
+KernelVersion:	3.11
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Specifies the chip power mode.
+		low_noise: reduce noise level from ADC,
+		low_power: enable low current consumption.
+		For a list of available output power modes read
+		in_accel_power_mode_available.
+
+What:		/sys/bus/iio/devices/iio:deviceX/store_eeprom
+KernelVersion:	3.4.0
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Writing '1' stores the current device configuration into
+		on-chip EEPROM. After power-up or chip reset the device will
+		automatically load the saved configuration.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523
index 2ce9c3f..a91aeab 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523
+++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523
@@ -18,14 +18,6 @@ Description:
 		Reading returns either '1' or '0'. '1' means that the
 		pllY is locked.
 
-What:		/sys/bus/iio/devices/iio:deviceX/store_eeprom
-KernelVersion:	3.4.0
-Contact:	linux-iio@vger.kernel.org
-Description:
-		Writing '1' stores the current device configuration into
-		on-chip EEPROM. After power-up or chip reset the device will
-		automatically load the saved configuration.
-
 What:		/sys/bus/iio/devices/iio:deviceX/sync_dividers
 KernelVersion:	3.4.0
 Contact:	linux-iio@vger.kernel.org
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350
index d89aded..1254457 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350
+++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350
@@ -18,4 +18,4 @@ Description:
 		adjust the reference frequency accordingly.
 		The value written has no effect until out_altvoltageY_frequency
 		is updated. Consider to use out_altvoltageY_powerdown to power
-		down the PLL and it's RFOut buffers during REFin changes.
+		down the PLL and its RFOut buffers during REFin changes.
diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt
index 16769d9..723c205 100644
--- a/Documentation/devicetree/bindings/arm/atmel-adc.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt
@@ -1,18 +1,15 @@
 * AT91's Analog to Digital Converter (ADC)
 
 Required properties:
-  - compatible: Should be "atmel,at91sam9260-adc"
+  - compatible: Should be "atmel,<chip>-adc"
+    <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
   - reg: Should contain ADC registers location and length
   - interrupts: Should contain the IRQ line for the ADC
-  - atmel,adc-channel-base: Offset of the first channel data register
   - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
     device
-  - atmel,adc-drdy-mask: Mask of the DRDY interruption in the ADC
   - atmel,adc-num-channels: Number of channels available in the ADC
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
     defined in the datasheet
-  - atmel,adc-status-register: Offset of the Interrupt Status Register
-  - atmel,adc-trigger-register: Offset of the Trigger Register
   - atmel,adc-vref: Reference voltage in millivolts for the conversions
   - atmel,adc-res: List of resolution in bits supported by the ADC. List size
 		   must be two at least.
diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt
new file mode 100644
index 0000000..c593357
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt
@@ -0,0 +1,24 @@
+* Bosch BMA180 triaxial acceleration sensor
+
+http://omapworld.com/BMA180_111_1002839.pdf
+
+Required properties:
+
+  - compatible : should be "bosch,bma180"
+  - reg : the I2C address of the sensor
+
+Optional properties:
+
+  - interrupt-parent : should be the phandle for the interrupt controller
+
+  - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
+		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+
+Example:
+
+bma180@40 {
+	compatible = "bosch,bma180";
+	reg = <0x40>;
+	interrupt-parent = <&gpio6>;
+	interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+};
diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt
new file mode 100644
index 0000000..e9582e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt
@@ -0,0 +1,18 @@
+* Nuvoton NAU7802 Analog to Digital Converter (ADC)
+
+Required properties:
+  - compatible: Should be "nuvoton,nau7802"
+  - reg: Should contain the ADC I2C address
+
+Optional properties:
+  - nuvoton,vldo: Internal reference voltage in millivolts to be
+    configured valid values are between 2400 mV and 4500 mV.
+  - interrupts: IRQ line for the ADC. If not used the driver will use
+    polling.
+
+Example:
+adc2: nau7802@2a {
+	compatible = "nuvoton,nau7802";
+	reg = <0x2a>;
+	nuvoton,vldo = <3000>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/apds9300.txt b/Documentation/devicetree/bindings/iio/light/apds9300.txt
new file mode 100644
index 0000000..d6f66c7
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/apds9300.txt
@@ -0,0 +1,22 @@
+* Avago APDS9300 ambient light sensor
+
+http://www.avagotech.com/docs/AV02-1077EN
+
+Required properties:
+
+  - compatible : should be "avago,apds9300"
+  - reg : the I2C address of the sensor
+
+Optional properties:
+
+  - interrupt-parent : should be the phandle for the interrupt controller
+  - interrupts : interrupt mapping for GPIO IRQ
+
+Example:
+
+apds9300@39 {
+	compatible = "avago,apds9300";
+	reg = <0x39>;
+	interrupt-parent = <&gpio2>;
+	interrupts = <29 8>;
+};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 366ce9b..ec4d713 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -11,6 +11,7 @@ amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 apm	Applied Micro Circuits Corporation (APM)
 arm	ARM Ltd.
 atmel	Atmel Corporation
+avago	Avago Technologies
 bosch	Bosch Sensortec GmbH
 brcm	Broadcom Corporation
 cavium	Cavium, Inc.
diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt
index b467145..fb57d85 100644
--- a/Documentation/driver-model/devres.txt
+++ b/Documentation/driver-model/devres.txt
@@ -237,6 +237,12 @@ MEM
   devm_kzalloc()
   devm_kfree()
 
+IIO
+  devm_iio_device_alloc()
+  devm_iio_device_free()
+  devm_iio_trigger_alloc()
+  devm_iio_trigger_free()
+
 IO region
   devm_request_region()
   devm_request_mem_region()