diff options
| -rw-r--r-- | arch/arm/mach-pxa/include/mach/palmtreo.h | 5 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/include/mach/smemc.h | 1 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/palmtreo.c | 70 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/smemc.c | 15 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/spitz.c | 4 |
5 files changed, 80 insertions, 15 deletions
diff --git a/arch/arm/mach-pxa/include/mach/palmtreo.h b/arch/arm/mach-pxa/include/mach/palmtreo.h index 2d3f14e..714b657 100644 --- a/arch/arm/mach-pxa/include/mach/palmtreo.h +++ b/arch/arm/mach-pxa/include/mach/palmtreo.h @@ -38,13 +38,14 @@ #define GPIO_NR_TREO_LCD_POWER 25 /* Treo680 specific GPIOs */ -#ifdef CONFIG_MACH_TREO680 #define GPIO_NR_TREO680_SD_READONLY 33 #define GPIO_NR_TREO680_SD_POWER 42 #define GPIO_NR_TREO680_VIBRATE_EN 44 #define GPIO_NR_TREO680_KEYB_BL 24 #define GPIO_NR_TREO680_BT_EN 43 -#endif /* CONFIG_MACH_TREO680 */ +#define GPIO_NR_TREO680_LCD_POWER 77 +#define GPIO_NR_TREO680_LCD_EN 86 +#define GPIO_NR_TREO680_LCD_EN_N 25 /* Centro685 specific GPIOs */ #define GPIO_NR_CENTRO_SD_POWER 21 diff --git a/arch/arm/mach-pxa/include/mach/smemc.h b/arch/arm/mach-pxa/include/mach/smemc.h index b7de471..b802f28 100644 --- a/arch/arm/mach-pxa/include/mach/smemc.h +++ b/arch/arm/mach-pxa/include/mach/smemc.h @@ -37,6 +37,7 @@ #define CSADRCFG1 (SMEMC_VIRT + 0x84) /* Address Configuration Register for CS1 */ #define CSADRCFG2 (SMEMC_VIRT + 0x88) /* Address Configuration Register for CS2 */ #define CSADRCFG3 (SMEMC_VIRT + 0x8C) /* Address Configuration Register for CS3 */ +#define CSMSADRCFG (SMEMC_VIRT + 0xA0) /* Chip Select Configuration Register */ /* * More handy macros for PCMCIA diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c index d17bda2..a29849d 100644 --- a/arch/arm/mach-pxa/palmtreo.c +++ b/arch/arm/mach-pxa/palmtreo.c @@ -98,9 +98,6 @@ static unsigned long treo_pin_config[] __initdata = { GPIO96_KP_MKOUT_6, GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH, /* Hotsync button */ - /* LCD */ - GPIOxx_LCD_TFT_16BPP, - /* Quick Capture Interface */ GPIO84_CIF_FV, GPIO85_CIF_LV, @@ -140,6 +137,12 @@ static unsigned long treo680_pin_config[] __initdata = { /* MATRIX KEYPAD - different wake up source */ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, GPIO99_KP_MKIN_5, + + /* LCD... L_BIAS alt fn not configured on Treo680; is GPIO instead */ + GPIOxx_LCD_16BPP, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, }; #endif /* CONFIG_MACH_TREO680 */ @@ -155,6 +158,9 @@ static unsigned long centro685_pin_config[] __initdata = { /* MATRIX KEYPAD - different wake up source */ GPIO100_KP_MKIN_0, GPIO99_KP_MKIN_5 | WAKEUP_ON_LEVEL_HIGH, + + /* LCD */ + GPIOxx_LCD_TFT_16BPP, }; #endif /* CONFIG_MACH_CENTRO */ @@ -328,7 +334,6 @@ static inline void palmtreo_uhc_init(void) {} /****************************************************************************** * Vibra and LEDs ******************************************************************************/ -#ifdef CONFIG_MACH_TREO680 static struct gpio_led treo680_gpio_leds[] = { { .name = "treo680:vibra:vibra", @@ -379,21 +384,17 @@ static struct gpio_led_platform_data centro_gpio_led_info = { static struct platform_device palmtreo_leds = { .name = "leds-gpio", .id = -1, - .dev = { - .platform_data = &treo680_gpio_led_info, - } }; static void __init palmtreo_leds_init(void) { if (machine_is_centro()) palmtreo_leds.dev.platform_data = ¢ro_gpio_led_info; + else if (machine_is_treo680()) + palmtreo_leds.dev.platform_data = &treo680_gpio_led_info; platform_device_register(&palmtreo_leds); } -#else -static inline void palmtreo_leds_init(void) {} -#endif /****************************************************************************** * Machine init @@ -424,10 +425,59 @@ static void __init palmphone_common_init(void) } #ifdef CONFIG_MACH_TREO680 +void __init treo680_gpio_init(void) +{ + unsigned int gpio; + + /* drive all three lcd gpios high initially */ + const unsigned long lcd_flags = GPIOF_INIT_HIGH | GPIOF_DIR_OUT; + + /* + * LCD GPIO initialization... + */ + + /* + * This is likely the power to the lcd. Toggling it low/high appears to + * turn the lcd off/on. Can be toggled after lcd is initialized without + * any apparent adverse effects to the lcd operation. Note that this + * gpio line is used by the lcd controller as the L_BIAS signal, but + * treo680 configures it as gpio. + */ + gpio = GPIO_NR_TREO680_LCD_POWER; + if (gpio_request_one(gpio, lcd_flags, "LCD power") < 0) + goto fail; + + /* + * These two are called "enables", for lack of a better understanding. + * If either of these are toggled after the lcd is initialized, the + * image becomes degraded. N.B. The IPL shipped with the treo + * configures GPIO_NR_TREO680_LCD_EN_N as output and drives it high. If + * the IPL is ever reprogrammed, this initialization may be need to be + * revisited. + */ + gpio = GPIO_NR_TREO680_LCD_EN; + if (gpio_request_one(gpio, lcd_flags, "LCD enable") < 0) + goto fail; + gpio = GPIO_NR_TREO680_LCD_EN_N; + if (gpio_request_one(gpio, lcd_flags, "LCD enable_n") < 0) + goto fail; + + /* driving this low turns LCD on */ + gpio_set_value(GPIO_NR_TREO680_LCD_EN_N, 0); + + return; + fail: + pr_err("gpio %d initialization failed\n", gpio); + gpio_free(GPIO_NR_TREO680_LCD_POWER); + gpio_free(GPIO_NR_TREO680_LCD_EN); + gpio_free(GPIO_NR_TREO680_LCD_EN_N); +} + static void __init treo680_init(void) { pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config)); palmphone_common_init(); + treo680_gpio_init(); palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, GPIO_NR_TREO680_SD_READONLY, GPIO_NR_TREO680_SD_POWER, 0); } diff --git a/arch/arm/mach-pxa/smemc.c b/arch/arm/mach-pxa/smemc.c index 7992305..f38aa89 100644 --- a/arch/arm/mach-pxa/smemc.c +++ b/arch/arm/mach-pxa/smemc.c @@ -40,6 +40,8 @@ static void pxa3xx_smemc_resume(void) __raw_writel(csadrcfg[1], CSADRCFG1); __raw_writel(csadrcfg[2], CSADRCFG2); __raw_writel(csadrcfg[3], CSADRCFG3); + /* CSMSADRCFG wakes up in its default state (0), so we need to set it */ + __raw_writel(0x2, CSMSADRCFG); } static struct syscore_ops smemc_syscore_ops = { @@ -49,8 +51,19 @@ static struct syscore_ops smemc_syscore_ops = { static int __init smemc_init(void) { - if (cpu_is_pxa3xx()) + if (cpu_is_pxa3xx()) { + /* + * The only documentation we have on the + * Chip Select Configuration Register (CSMSADRCFG) is that + * it must be programmed to 0x2. + * Moreover, in the bit definitions, the second bit + * (CSMSADRCFG[1]) is called "SETALWAYS". + * Other bits are reserved in this register. + */ + __raw_writel(0x2, CSMSADRCFG); + register_syscore_ops(&smemc_syscore_ops); + } return 0; } diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index f90aa27..362726c 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -732,7 +732,7 @@ static inline void spitz_lcd_init(void) {} #endif /****************************************************************************** - * Framebuffer + * NAND Flash ******************************************************************************/ #if defined(CONFIG_MTD_NAND_SHARPSL) || defined(CONFIG_MTD_NAND_SHARPSL_MODULE) static struct mtd_partition spitz_nand_partitions[] = { @@ -858,7 +858,7 @@ static inline void spitz_nor_init(void) {} #endif /****************************************************************************** - * GPIO expander + * I2C devices ******************************************************************************/ #if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE) static struct pca953x_platform_data akita_pca953x_pdata = { |