diff options
Diffstat (limited to 'Documentation/ABI')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio | 19 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 | 8 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 | 2 |
3 files changed, 20 insertions, 9 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index dda81ff..39c8de0 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -351,6 +351,7 @@ Description: 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 20kohm_to_gnd: connected to ground via a 20kOhm resistor, 100kohm_to_gnd: connected to ground via an 100kOhm resistor, + 500kohm_to_gnd: connected to ground via a 500kOhm resistor, three_state: left floating. For a list of available output power down options read outX_powerdown_mode_available. If Y is not present the @@ -792,3 +793,21 @@ Contact: linux-iio@vger.kernel.org Description: This attribute is used to read the amount of quadrature error present in the device at a given time. + +What: /sys/.../iio:deviceX/in_accelX_power_mode +KernelVersion: 3.11 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the chip power mode. + low_noise: reduce noise level from ADC, + low_power: enable low current consumption. + For a list of available output power modes read + in_accel_power_mode_available. + +What: /sys/bus/iio/devices/iio:deviceX/store_eeprom +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Writing '1' stores the current device configuration into + on-chip EEPROM. After power-up or chip reset the device will + automatically load the saved configuration. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 index 2ce9c3f..a91aeab 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 @@ -18,14 +18,6 @@ Description: Reading returns either '1' or '0'. '1' means that the pllY is locked. -What: /sys/bus/iio/devices/iio:deviceX/store_eeprom -KernelVersion: 3.4.0 -Contact: linux-iio@vger.kernel.org -Description: - Writing '1' stores the current device configuration into - on-chip EEPROM. After power-up or chip reset the device will - automatically load the saved configuration. - What: /sys/bus/iio/devices/iio:deviceX/sync_dividers KernelVersion: 3.4.0 Contact: linux-iio@vger.kernel.org diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 index d89aded..1254457 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 @@ -18,4 +18,4 @@ Description: adjust the reference frequency accordingly. The value written has no effect until out_altvoltageY_frequency is updated. Consider to use out_altvoltageY_powerdown to power - down the PLL and it's RFOut buffers during REFin changes. + down the PLL and its RFOut buffers during REFin changes. |