diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pwm')
8 files changed, 160 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 0000000..131e8c1 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,23 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,am33xx-ecap" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the ECAP: + "ecap<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ecap0: ecap@0 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 0000000..4fc7079 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,23 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible : Must be "ti,am33xx-ehrpwm" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the EHRPWM: + "ehrpwm<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ehrpwm0: ehrpwm@0 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + ti,hwmods = "ehrpwm0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 0000000..f7eae77 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,31 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,am33xx-pwmss"; +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +pwmss0: pwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt index 73ec962..06e6724 100644 --- a/Documentation/devicetree/bindings/pwm/pwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -37,10 +37,21 @@ device: pwm-names = "backlight"; }; +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + pwm-specifier typically encodes the chip-relative PWM number and the PWM -period in nanoseconds. Note that in the example above, specifying the -"pwm-names" is redundant because the name "backlight" would be used as -fallback anyway. +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags in a third cell: +- bit 0: PWM signal polarity (0: normal polarity, 1: inverse polarity) + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 1>; + pwm-names = "backlight"; + }; 2) PWM controller nodes ----------------------- diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 0000000..3ac779d --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,18 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: number of cells used to specify PWM which is fixed to 2 on + SPEAr. The first cell specifies the per-chip index of the PWM to use and + the second cell is the period in nanoseconds. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 0000000..2943ee5 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 0000000..cb64f3a --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 0000000..bcc6367 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <2>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; |