diff options
Diffstat (limited to 'arch/arm/mach-mx25')
| -rw-r--r-- | arch/arm/mach-mx25/Kconfig | 18 | ||||
| -rw-r--r-- | arch/arm/mach-mx25/Makefile | 2 | ||||
| -rw-r--r-- | arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c | 260 | ||||
| -rw-r--r-- | arch/arm/mach-mx25/mach-cpuimx25.c | 172 |
4 files changed, 452 insertions, 0 deletions
diff --git a/arch/arm/mach-mx25/Kconfig b/arch/arm/mach-mx25/Kconfig index 54d2173..3a6668e 100644 --- a/arch/arm/mach-mx25/Kconfig +++ b/arch/arm/mach-mx25/Kconfig @@ -5,4 +5,22 @@ comment "MX25 platforms:" config MACH_MX25_3DS bool "Support MX25PDK (3DS) Platform" +config MACH_EUKREA_CPUIMX25 + bool "Support Eukrea CPUIMX25 Platform" + select MXC_ULPI if USB_ULPI + +choice + prompt "Baseboard" + depends on MACH_EUKREA_CPUIMX25 + default MACH_EUKREA_MBIMXSD_BASEBOARD + +config MACH_EUKREA_MBIMXSD_BASEBOARD + prompt "Eukrea MBIMXSD development board" + bool + help + This adds board specific devices that can be found on Eukrea's + MBIMXSD evaluation board. + +endchoice + endif diff --git a/arch/arm/mach-mx25/Makefile b/arch/arm/mach-mx25/Makefile index 10cebc5..83ab5d8 100644 --- a/arch/arm/mach-mx25/Makefile +++ b/arch/arm/mach-mx25/Makefile @@ -1,3 +1,5 @@ obj-y := mm.o devices.o obj-$(CONFIG_ARCH_MX25) += clock.o obj-$(CONFIG_MACH_MX25_3DS) += mach-mx25pdk.o +obj-$(CONFIG_MACH_EUKREA_CPUIMX25) += mach-cpuimx25.o +obj-$(CONFIG_MACH_EUKREA_MBIMXSD_BASEBOARD) += eukrea_mbimxsd-baseboard.o diff --git a/arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c b/arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c new file mode 100644 index 0000000..e0f0dfd --- /dev/null +++ b/arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c @@ -0,0 +1,260 @@ +/* + * Copyright (C) 2010 Eric Benard - eric@eukrea.com + * + * Based on pcm970-baseboard.c which is : + * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#include <linux/gpio.h> +#include <linux/leds.h> +#include <linux/platform_device.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <video/platform_lcd.h> + +#include <mach/board-eukrea_cpuimx25.h> +#include <mach/hardware.h> +#include <mach/iomux-mx25.h> +#include <mach/common.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/mx25.h> +#include <mach/imx-uart.h> +#include <mach/imxfb.h> +#include <mach/ssi.h> +#include <mach/audmux.h> + +#include "devices.h" + +static struct pad_desc eukrea_mbimxsd_pads[] = { + /* LCD */ + MX25_PAD_LD0__LD0, + MX25_PAD_LD1__LD1, + MX25_PAD_LD2__LD2, + MX25_PAD_LD3__LD3, + MX25_PAD_LD4__LD4, + MX25_PAD_LD5__LD5, + MX25_PAD_LD6__LD6, + MX25_PAD_LD7__LD7, + MX25_PAD_LD8__LD8, + MX25_PAD_LD9__LD9, + MX25_PAD_LD10__LD10, + MX25_PAD_LD11__LD11, + MX25_PAD_LD12__LD12, + MX25_PAD_LD13__LD13, + MX25_PAD_LD14__LD14, + MX25_PAD_LD15__LD15, + MX25_PAD_GPIO_E__LD16, + MX25_PAD_GPIO_F__LD17, + MX25_PAD_HSYNC__HSYNC, + MX25_PAD_VSYNC__VSYNC, + MX25_PAD_LSCLK__LSCLK, + MX25_PAD_OE_ACD__OE_ACD, + MX25_PAD_CONTRAST__CONTRAST, + /* LCD_PWR */ + MX25_PAD_PWM__GPIO_1_26, + /* LED */ + MX25_PAD_POWER_FAIL__GPIO_3_19, + /* SWITCH */ + MX25_PAD_VSTBY_ACK__GPIO_3_18, + /* UART2 */ + MX25_PAD_UART2_RTS__UART2_RTS, + MX25_PAD_UART2_CTS__UART2_CTS, + MX25_PAD_UART2_TXD__UART2_TXD, + MX25_PAD_UART2_RXD__UART2_RXD, + /* SD1 */ + MX25_PAD_SD1_CMD__SD1_CMD, + MX25_PAD_SD1_CLK__SD1_CLK, + MX25_PAD_SD1_DATA0__SD1_DATA0, + MX25_PAD_SD1_DATA1__SD1_DATA1, + MX25_PAD_SD1_DATA2__SD1_DATA2, + MX25_PAD_SD1_DATA3__SD1_DATA3, + /* SD1 CD */ + MX25_PAD_DE_B__GPIO_2_20, + /* I2S */ + MX25_PAD_KPP_COL3__AUD5_TXFS, + MX25_PAD_KPP_COL2__AUD5_TXC, + MX25_PAD_KPP_COL1__AUD5_RXD, + MX25_PAD_KPP_COL0__AUD5_TXD, +}; + +#define GPIO_LED1 83 +#define GPIO_SWITCH1 82 +#define GPIO_SD1CD 52 +#define GPIO_LCDPWR 26 + +static struct imx_fb_videomode eukrea_mximxsd_modes[] = { + { + .mode = { + .name = "CMO-QVGA", + .refresh = 60, + .xres = 320, + .yres = 240, + .pixclock = KHZ2PICOS(6500), + .left_margin = 30, + .right_margin = 38, + .upper_margin = 20, + .lower_margin = 3, + .hsync_len = 15, + .vsync_len = 4, + }, + .bpp = 16, + .pcr = 0xCAD08B80, + }, +}; + +static struct imx_fb_platform_data eukrea_mximxsd_fb_pdata = { + .mode = eukrea_mximxsd_modes, + .num_modes = ARRAY_SIZE(eukrea_mximxsd_modes), + .pwmr = 0x00A903FF, + .lscr1 = 0x00120300, + .dmacr = 0x00040060, +}; + +static void eukrea_mbimxsd_lcd_power_set(struct plat_lcd_data *pd, + unsigned int power) +{ + if (power) + gpio_direction_output(GPIO_LCDPWR, 1); + else + gpio_direction_output(GPIO_LCDPWR, 0); +} + +static struct plat_lcd_data eukrea_mbimxsd_lcd_power_data = { + .set_power = eukrea_mbimxsd_lcd_power_set, +}; + +static struct platform_device eukrea_mbimxsd_lcd_powerdev = { + .name = "platform-lcd", + .dev.platform_data = &eukrea_mbimxsd_lcd_power_data, +}; + +static struct gpio_led eukrea_mbimxsd_leds[] = { + { + .name = "led1", + .default_trigger = "heartbeat", + .active_low = 1, + .gpio = GPIO_LED1, + }, +}; + +static struct gpio_led_platform_data eukrea_mbimxsd_led_info = { + .leds = eukrea_mbimxsd_leds, + .num_leds = ARRAY_SIZE(eukrea_mbimxsd_leds), +}; + +static struct platform_device eukrea_mbimxsd_leds_gpio = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &eukrea_mbimxsd_led_info, + }, +}; + +static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = { + { + .gpio = GPIO_SWITCH1, + .code = BTN_0, + .desc = "BP1", + .active_low = 1, + .wakeup = 1, + }, +}; + +static struct gpio_keys_platform_data eukrea_mbimxsd_button_data = { + .buttons = eukrea_mbimxsd_gpio_buttons, + .nbuttons = ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons), +}; + +static struct platform_device eukrea_mbimxsd_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &eukrea_mbimxsd_button_data, + } +}; + +static struct platform_device *platform_devices[] __initdata = { + &eukrea_mbimxsd_leds_gpio, + &eukrea_mbimxsd_button_device, + &eukrea_mbimxsd_lcd_powerdev, +}; + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = { + { + I2C_BOARD_INFO("tlv320aic23", 0x1a), + }, +}; + +struct imx_ssi_platform_data eukrea_mbimxsd_ssi_pdata = { + .flags = IMX_SSI_SYN | IMX_SSI_NET | IMX_SSI_USE_I2S_SLAVE, +}; + +/* + * system init for baseboard usage. Will be called by cpuimx25 init. + * + * Add platform devices present on this baseboard and init + * them from CPU side as far as required to use them later on + */ +void __init eukrea_mbimxsd_baseboard_init(void) +{ + if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads, + ARRAY_SIZE(eukrea_mbimxsd_pads))) + printk(KERN_ERR "error setting mbimxsd pads !\n"); + +#if defined(CONFIG_SND_SOC_EUKREA_TLV320) + /* SSI unit master I2S codec connected to SSI_AUD5*/ + mxc_audmux_v2_configure_port(0, + MXC_AUDMUX_V2_PTCR_SYN | + MXC_AUDMUX_V2_PTCR_TFSDIR | + MXC_AUDMUX_V2_PTCR_TFSEL(4) | + MXC_AUDMUX_V2_PTCR_TCLKDIR | + MXC_AUDMUX_V2_PTCR_TCSEL(4), + MXC_AUDMUX_V2_PDCR_RXDSEL(4) + ); + mxc_audmux_v2_configure_port(4, + MXC_AUDMUX_V2_PTCR_SYN, + MXC_AUDMUX_V2_PDCR_RXDSEL(0) + ); +#endif + + mxc_register_device(&mxc_uart_device1, &uart_pdata); + mxc_register_device(&mx25_fb_device, &eukrea_mximxsd_fb_pdata); + mxc_register_device(&imx_ssi_device0, &eukrea_mbimxsd_ssi_pdata); + + gpio_request(GPIO_LED1, "LED1"); + gpio_direction_output(GPIO_LED1, 1); + gpio_free(GPIO_LED1); + + gpio_request(GPIO_SWITCH1, "SWITCH1"); + gpio_direction_input(GPIO_SWITCH1); + gpio_free(GPIO_SWITCH1); + + gpio_request(GPIO_LCDPWR, "LCDPWR"); + gpio_direction_output(GPIO_LCDPWR, 1); + gpio_free(GPIO_SWITCH1); + + i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices, + ARRAY_SIZE(eukrea_mbimxsd_i2c_devices)); + + platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); +} diff --git a/arch/arm/mach-mx25/mach-cpuimx25.c b/arch/arm/mach-mx25/mach-cpuimx25.c new file mode 100644 index 0000000..4796484 --- /dev/null +++ b/arch/arm/mach-mx25/mach-cpuimx25.c @@ -0,0 +1,172 @@ +/* + * Copyright 2009 Sascha Hauer, <kernel@pengutronix.de> + * Copyright 2010 Eric Bénard - Eukréa Electromatique, <eric@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, + * Boston, MA 02110-1301, USA. + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/irq.h> +#include <linux/gpio.h> +#include <linux/fec.h> +#include <linux/platform_device.h> +#include <linux/usb/otg.h> +#include <linux/usb/ulpi.h> +#include <linux/fsl_devices.h> + +#include <mach/board-eukrea_cpuimx25.h> +#include <mach/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/memory.h> +#include <asm/mach/map.h> +#include <mach/common.h> +#include <mach/imx-uart.h> +#include <mach/i2c.h> +#include <mach/mx25.h> +#include <mach/mxc_nand.h> +#include <mach/imxfb.h> +#include <mach/mxc_ehci.h> +#include <mach/ulpi.h> + +#include "devices.h" +#include <mach/iomux-mx25.h> + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static struct pad_desc eukrea_cpuimx25_pads[] = { + /* FEC - RMII */ + MX25_PAD_FEC_MDC__FEC_MDC, + MX25_PAD_FEC_MDIO__FEC_MDIO, + MX25_PAD_FEC_TDATA0__FEC_TDATA0, + MX25_PAD_FEC_TDATA1__FEC_TDATA1, + MX25_PAD_FEC_TX_EN__FEC_TX_EN, + MX25_PAD_FEC_RDATA0__FEC_RDATA0, + MX25_PAD_FEC_RDATA1__FEC_RDATA1, + MX25_PAD_FEC_RX_DV__FEC_RX_DV, + MX25_PAD_FEC_TX_CLK__FEC_TX_CLK, + /* I2C1 */ + MX25_PAD_I2C1_CLK__I2C1_CLK, + MX25_PAD_I2C1_DAT__I2C1_DAT, +}; + +static struct fec_platform_data mx25_fec_pdata = { + .phy = PHY_INTERFACE_MODE_RMII, +}; + +static struct mxc_nand_platform_data eukrea_cpuimx25_nand_board_info = { + .width = 1, + .hw_ecc = 1, + .flash_bbt = 1, +}; + +static struct imxi2c_platform_data eukrea_cpuimx25_i2c_1_data = { + .bitrate = 100000, +}; + +static struct i2c_board_info eukrea_cpuimx25_i2c_devices[] = { + { + I2C_BOARD_INFO("pcf8563", 0x51), + }, +}; + +static struct mxc_usbh_platform_data otg_pdata = { + .portsc = MXC_EHCI_MODE_UTMI, + .flags = MXC_EHCI_INTERFACE_DIFF_UNI, +}; + +static struct mxc_usbh_platform_data usbh2_pdata = { + .portsc = MXC_EHCI_MODE_SERIAL, + .flags = MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY | + MXC_EHCI_IPPUE_DOWN, +}; + +static struct fsl_usb2_platform_data otg_device_pdata = { + .operating_mode = FSL_USB2_DR_DEVICE, + .phy_mode = FSL_USB2_PHY_UTMI, +}; + +static int otg_mode_host; + +static int __init eukrea_cpuimx25_otg_mode(char *options) +{ + if (!strcmp(options, "host")) + otg_mode_host = 1; + else if (!strcmp(options, "device")) + otg_mode_host = 0; + else + pr_info("otg_mode neither \"host\" nor \"device\". " + "Defaulting to device\n"); + return 0; +} +__setup("otg_mode=", eukrea_cpuimx25_otg_mode); + +static void __init eukrea_cpuimx25_init(void) +{ + if (mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx25_pads, + ARRAY_SIZE(eukrea_cpuimx25_pads))) + printk(KERN_ERR "error setting cpuimx25 pads !\n"); + + mxc_register_device(&mxc_uart_device0, &uart_pdata); + mxc_register_device(&mxc_nand_device, &eukrea_cpuimx25_nand_board_info); + mxc_register_device(&mx25_rtc_device, NULL); + mxc_register_device(&mx25_fec_device, &mx25_fec_pdata); + + i2c_register_board_info(0, eukrea_cpuimx25_i2c_devices, + ARRAY_SIZE(eukrea_cpuimx25_i2c_devices)); + mxc_register_device(&mxc_i2c_device0, &eukrea_cpuimx25_i2c_1_data); + +#if defined(CONFIG_USB_ULPI) + if (otg_mode_host) { + otg_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops, + USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT); + + mxc_register_device(&mxc_otg, &otg_pdata); + } + mxc_register_device(&mxc_usbh2, &usbh2_pdata); +#endif + if (!otg_mode_host) + mxc_register_device(&otg_udc_device, &otg_device_pdata); + +#ifdef CONFIG_MACH_EUKREA_MBIMXSD_BASEBOARD + eukrea_mbimxsd_baseboard_init(); +#endif +} + +static void __init eukrea_cpuimx25_timer_init(void) +{ + mx25_clocks_init(); +} + +static struct sys_timer eukrea_cpuimx25_timer = { + .init = eukrea_cpuimx25_timer_init, +}; + +MACHINE_START(EUKREA_CPUIMX25, "Eukrea CPUIMX25") + /* Maintainer: Eukrea Electromatique */ + .phys_io = MX25_AIPS1_BASE_ADDR, + .io_pg_offst = ((MX25_AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, + .boot_params = MX25_PHYS_OFFSET + 0x100, + .map_io = mx25_map_io, + .init_irq = mx25_init_irq, + .init_machine = eukrea_cpuimx25_init, + .timer = &eukrea_cpuimx25_timer, +MACHINE_END |