diff options
Diffstat (limited to 'drivers/scsi/advansys.c')
-rw-r--r-- | drivers/scsi/advansys.c | 101 |
1 files changed, 8 insertions, 93 deletions
diff --git a/drivers/scsi/advansys.c b/drivers/scsi/advansys.c index 9b3303b..2b66897 100644 --- a/drivers/scsi/advansys.c +++ b/drivers/scsi/advansys.c @@ -798,7 +798,6 @@ #include <scsi/scsi_tcq.h> #include <scsi/scsi.h> #include <scsi/scsi_host.h> -#include "advansys.h" #ifdef CONFIG_PCI #include <linux/pci.h> #endif /* CONFIG_PCI */ @@ -2014,7 +2013,7 @@ STATIC int AscSgListToQueue(int); STATIC void AscEnableIsaDma(uchar); #endif /* CONFIG_ISA */ STATIC ASC_DCNT AscGetMaxDmaCount(ushort); - +static const char *advansys_info(struct Scsi_Host *shp); /* * --- Adv Library Constants and Macros @@ -3970,10 +3969,6 @@ STATIC ushort asc_bus[ASC_NUM_BUS] __initdata = { ASC_IS_PCI, }; -/* - * Used with the LILO 'advansys' option to eliminate or - * limit I/O port probing at boot time, cf. advansys_setup(). - */ STATIC int asc_iopflag = ASC_FALSE; STATIC int asc_ioport[ASC_NUM_IOPORT_PROBE] = { 0, 0, 0, 0 }; @@ -4055,10 +4050,6 @@ STATIC void asc_prt_hex(char *f, uchar *, int); #endif /* ADVANSYS_DEBUG */ -/* - * --- Linux 'struct scsi_host_template' and advansys_setup() Functions - */ - #ifdef CONFIG_PROC_FS /* * advansys_proc_info() - /proc/scsi/advansys/[0-(ASC_NUM_BOARD_SUPPORTED-1)] @@ -4080,7 +4071,7 @@ STATIC void asc_prt_hex(char *f, uchar *, int); * if 'prtbuf' is too small it will not be overwritten. Instead the * user just won't get all the available statistics. */ -int +static int advansys_proc_info(struct Scsi_Host *shost, char *buffer, char **start, off_t offset, int length, int inout) { @@ -4296,7 +4287,7 @@ advansys_proc_info(struct Scsi_Host *shost, char *buffer, char **start, * it must not call SCSI mid-level functions including scsi_malloc() * and scsi_free(). */ -int __init +static int __init advansys_detect(struct scsi_host_template *tpnt) { static int detect_called = ASC_FALSE; @@ -5428,7 +5419,7 @@ advansys_detect(struct scsi_host_template *tpnt) * * Release resources allocated for a single AdvanSys adapter. */ -int +static int advansys_release(struct Scsi_Host *shp) { asc_board_t *boardp; @@ -5475,7 +5466,7 @@ advansys_release(struct Scsi_Host *shp) * Note: The information line should not exceed ASC_INFO_SIZE bytes, * otherwise the static 'info' array will be overrun. */ -const char * +static const char * advansys_info(struct Scsi_Host *shp) { static char info[ASC_INFO_SIZE]; @@ -5568,7 +5559,7 @@ advansys_info(struct Scsi_Host *shp) * This function always returns 0. Command return status is saved * in the 'scp' result field. */ -int +static int advansys_queuecommand(struct scsi_cmnd *scp, void (*done)(struct scsi_cmnd *)) { struct Scsi_Host *shp; @@ -5656,7 +5647,7 @@ advansys_queuecommand(struct scsi_cmnd *scp, void (*done)(struct scsi_cmnd *)) * sleeping is allowed and no locking other than for host structures is * required. Returns SUCCESS or FAILED. */ -int +static int advansys_reset(struct scsi_cmnd *scp) { struct Scsi_Host *shp; @@ -5841,7 +5832,7 @@ advansys_reset(struct scsi_cmnd *scp) * ip[1]: sectors * ip[2]: cylinders */ -int +static int advansys_biosparam(struct scsi_device *sdev, struct block_device *bdev, sector_t capacity, int ip[]) { @@ -5875,82 +5866,6 @@ advansys_biosparam(struct scsi_device *sdev, struct block_device *bdev, } /* - * advansys_setup() - * - * This function is called from init/main.c at boot time. - * It it passed LILO parameters that can be set from the - * LILO command line or in /etc/lilo.conf. - * - * It is used by the AdvanSys driver to either disable I/O - * port scanning or to limit scanning to 1 - 4 I/O ports. - * Regardless of the option setting EISA and PCI boards - * will still be searched for and detected. This option - * only affects searching for ISA and VL boards. - * - * If ADVANSYS_DEBUG is defined the driver debug level may - * be set using the 5th (ASC_NUM_IOPORT_PROBE + 1) I/O Port. - * - * Examples: - * 1. Eliminate I/O port scanning: - * boot: linux advansys= - * or - * boot: linux advansys=0x0 - * 2. Limit I/O port scanning to one I/O port: - * boot: linux advansys=0x110 - * 3. Limit I/O port scanning to four I/O ports: - * boot: linux advansys=0x110,0x210,0x230,0x330 - * 4. If ADVANSYS_DEBUG, limit I/O port scanning to four I/O ports and - * set the driver debug level to 2. - * boot: linux advansys=0x110,0x210,0x230,0x330,0xdeb2 - * - * ints[0] - number of arguments - * ints[1] - first argument - * ints[2] - second argument - * ... - */ -void __init -advansys_setup(char *str, int *ints) -{ - int i; - - if (asc_iopflag == ASC_TRUE) { - printk("AdvanSys SCSI: 'advansys' LILO option may appear only once\n"); - return; - } - - asc_iopflag = ASC_TRUE; - - if (ints[0] > ASC_NUM_IOPORT_PROBE) { -#ifdef ADVANSYS_DEBUG - if ((ints[0] == ASC_NUM_IOPORT_PROBE + 1) && - (ints[ASC_NUM_IOPORT_PROBE + 1] >> 4 == 0xdeb)) { - asc_dbglvl = ints[ASC_NUM_IOPORT_PROBE + 1] & 0xf; - } else { -#endif /* ADVANSYS_DEBUG */ - printk("AdvanSys SCSI: only %d I/O ports accepted\n", - ASC_NUM_IOPORT_PROBE); -#ifdef ADVANSYS_DEBUG - } -#endif /* ADVANSYS_DEBUG */ - } - -#ifdef ADVANSYS_DEBUG - ASC_DBG1(1, "advansys_setup: ints[0] %d\n", ints[0]); - for (i = 1; i < ints[0]; i++) { - ASC_DBG2(1, " ints[%d] 0x%x", i, ints[i]); - } - ASC_DBG(1, "\n"); -#endif /* ADVANSYS_DEBUG */ - - for (i = 1; i <= ints[0] && i <= ASC_NUM_IOPORT_PROBE; i++) { - asc_ioport[i-1] = ints[i]; - ASC_DBG2(1, "advansys_setup: asc_ioport[%d] 0x%x\n", - i - 1, asc_ioport[i-1]); - } -} - - -/* * --- Loadable Driver Support */ |