diff options
Diffstat (limited to 'drivers/serial/max3107-aava.c')
| -rw-r--r-- | drivers/serial/max3107-aava.c | 344 |
1 files changed, 344 insertions, 0 deletions
diff --git a/drivers/serial/max3107-aava.c b/drivers/serial/max3107-aava.c new file mode 100644 index 0000000..a1fe304 --- /dev/null +++ b/drivers/serial/max3107-aava.c @@ -0,0 +1,344 @@ +/* + * max3107.c - spi uart protocol driver for Maxim 3107 + * Based on max3100.c + * by Christian Pellegrin <chripell@evolware.org> + * and max3110.c + * by Feng Tang <feng.tang@intel.com> + * + * Copyright (C) Aavamobile 2009 + * + * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + * + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/spi/spi.h> +#include <linux/freezer.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/sfi.h> +#include <asm/mrst.h> +#include "max3107.h" + +/* GPIO direction to input function */ +static int max3107_gpio_direction_in(struct gpio_chip *chip, unsigned offset) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[1]; /* Buffer for SPI transfer */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return -EINVAL; + } + + /* Read current GPIO configuration register */ + buf[0] = MAX3107_GPIOCFG_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { + dev_err(&s->spi->dev, "SPI transfer GPIO read failed\n"); + return -EIO; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + + /* Set GPIO to input */ + buf[0] &= ~(0x0001 << offset); + + /* Write new GPIO configuration register value */ + buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIOCFG_REG); + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 2)) { + dev_err(&s->spi->dev, "SPI transfer GPIO write failed\n"); + return -EIO; + } + return 0; +} + +/* GPIO direction to output function */ +static int max3107_gpio_direction_out(struct gpio_chip *chip, unsigned offset, + int value) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[2]; /* Buffer for SPI transfers */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return -EINVAL; + } + + /* Read current GPIO configuration and data registers */ + buf[0] = MAX3107_GPIOCFG_REG; + buf[1] = MAX3107_GPIODATA_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 4)) { + dev_err(&s->spi->dev, "SPI transfer gpio failed\n"); + return -EIO; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + buf[1] &= MAX3107_SPI_RX_DATA_MASK; + + /* Set GPIO to output */ + buf[0] |= (0x0001 << offset); + /* Set value */ + if (value) + buf[1] |= (0x0001 << offset); + else + buf[1] &= ~(0x0001 << offset); + + /* Write new GPIO configuration and data register values */ + buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIOCFG_REG); + buf[1] |= (MAX3107_WRITE_BIT | MAX3107_GPIODATA_REG); + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 4)) { + dev_err(&s->spi->dev, + "SPI transfer for GPIO conf data w failed\n"); + return -EIO; + } + return 0; +} + +/* GPIO value query function */ +static int max3107_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[1]; /* Buffer for SPI transfer */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return -EINVAL; + } + + /* Read current GPIO data register */ + buf[0] = MAX3107_GPIODATA_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { + dev_err(&s->spi->dev, "SPI transfer GPIO data r failed\n"); + return -EIO; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + + /* Return value */ + return buf[0] & (0x0001 << offset); +} + +/* GPIO value set function */ +static void max3107_gpio_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[2]; /* Buffer for SPI transfers */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return; + } + + /* Read current GPIO configuration registers*/ + buf[0] = MAX3107_GPIODATA_REG; + buf[1] = MAX3107_GPIOCFG_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 4)) { + dev_err(&s->spi->dev, + "SPI transfer for GPIO data and config read failed\n"); + return; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + buf[1] &= MAX3107_SPI_RX_DATA_MASK; + + if (!(buf[1] & (0x0001 << offset))) { + /* Configured as input, can't set value */ + dev_warn(&s->spi->dev, + "Trying to set value for input GPIO\n"); + return; + } + + /* Set value */ + if (value) + buf[0] |= (0x0001 << offset); + else + buf[0] &= ~(0x0001 << offset); + + /* Write new GPIO data register value */ + buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIODATA_REG); + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 2)) + dev_err(&s->spi->dev, "SPI transfer GPIO data w failed\n"); +} + +/* GPIO chip data */ +static struct gpio_chip max3107_gpio_chip = { + .owner = THIS_MODULE, + .direction_input = max3107_gpio_direction_in, + .direction_output = max3107_gpio_direction_out, + .get = max3107_gpio_get, + .set = max3107_gpio_set, + .can_sleep = 1, + .base = MAX3107_GPIO_BASE, + .ngpio = MAX3107_GPIO_COUNT, +}; + +/** + * max3107_aava_reset - reset on AAVA systems + * @spi: The SPI device we are probing + * + * Reset the device ready for probing. + */ + +static int max3107_aava_reset(struct spi_device *spi) +{ + /* Reset the chip */ + if (gpio_request(MAX3107_RESET_GPIO, "max3107")) { + pr_err("Requesting RESET GPIO failed\n"); + return -EIO; + } + if (gpio_direction_output(MAX3107_RESET_GPIO, 0)) { + pr_err("Setting RESET GPIO to 0 failed\n"); + gpio_free(MAX3107_RESET_GPIO); + return -EIO; + } + msleep(MAX3107_RESET_DELAY); + if (gpio_direction_output(MAX3107_RESET_GPIO, 1)) { + pr_err("Setting RESET GPIO to 1 failed\n"); + gpio_free(MAX3107_RESET_GPIO); + return -EIO; + } + gpio_free(MAX3107_RESET_GPIO); + msleep(MAX3107_WAKEUP_DELAY); + return 0; +} + +static int max3107_aava_configure(struct max3107_port *s) +{ + int retval; + + /* Initialize GPIO chip data */ + s->chip = max3107_gpio_chip; + s->chip.label = s->spi->modalias; + s->chip.dev = &s->spi->dev; + + /* Add GPIO chip */ + retval = gpiochip_add(&s->chip); + if (retval) { + dev_err(&s->spi->dev, "Adding GPIO chip failed\n"); + return retval; + } + + /* Temporary fix for EV2 boot problems, set modem reset to 0 */ + max3107_gpio_direction_out(&s->chip, 3, 0); + return 0; +} + +#if 0 +/* This will get enabled once we have the board stuff merged for this + specific case */ + +static const struct baud_table brg13_ext[] = { + { 300, MAX3107_BRG13_B300 }, + { 600, MAX3107_BRG13_B600 }, + { 1200, MAX3107_BRG13_B1200 }, + { 2400, MAX3107_BRG13_B2400 }, + { 4800, MAX3107_BRG13_B4800 }, + { 9600, MAX3107_BRG13_B9600 }, + { 19200, MAX3107_BRG13_B19200 }, + { 57600, MAX3107_BRG13_B57600 }, + { 115200, MAX3107_BRG13_B115200 }, + { 230400, MAX3107_BRG13_B230400 }, + { 460800, MAX3107_BRG13_B460800 }, + { 921600, MAX3107_BRG13_B921600 }, + { 0, 0 } +}; + +static void max3107_aava_init(struct max3107_port *s) +{ + /*override for AAVA SC specific*/ + if (mrst_platform_id() == MRST_PLATFORM_AAVA_SC) { + if (get_koski_build_id() <= KOSKI_EV2) + if (s->ext_clk) { + s->brg_cfg = MAX3107_BRG13_B9600; + s->baud_tbl = (struct baud_table *)brg13_ext; + } + } +} +#endif + +static int __devexit max3107_aava_remove(struct spi_device *spi) +{ + struct max3107_port *s = dev_get_drvdata(&spi->dev); + + /* Remove GPIO chip */ + if (gpiochip_remove(&s->chip)) + dev_warn(&spi->dev, "Removing GPIO chip failed\n"); + + /* Then do the default remove */ + return max3107_remove(spi); +} + +/* Platform data */ +static struct max3107_plat aava_plat_data = { + .loopback = 0, + .ext_clk = 1, +/* .init = max3107_aava_init, */ + .configure = max3107_aava_configure, + .hw_suspend = max3107_hw_susp, + .polled_mode = 0, + .poll_time = 0, +}; + + +static int __devinit max3107_probe_aava(struct spi_device *spi) +{ + int err = max3107_aava_reset(spi); + if (err < 0) + return err; + return max3107_probe(spi, &aava_plat_data); +} + +/* Spi driver data */ +static struct spi_driver max3107_driver = { + .driver = { + .name = "aava-max3107", + .bus = &spi_bus_type, + .owner = THIS_MODULE, + }, + .probe = max3107_probe_aava, + .remove = __devexit_p(max3107_aava_remove), + .suspend = max3107_suspend, + .resume = max3107_resume, +}; + +/* Driver init function */ +static int __init max3107_init(void) +{ + return spi_register_driver(&max3107_driver); +} + +/* Driver exit function */ +static void __exit max3107_exit(void) +{ + spi_unregister_driver(&max3107_driver); +} + +module_init(max3107_init); +module_exit(max3107_exit); + +MODULE_DESCRIPTION("MAX3107 driver"); +MODULE_AUTHOR("Aavamobile"); +MODULE_ALIAS("aava-max3107-spi"); +MODULE_LICENSE("GPL v2"); |