[MIPS] Pb1000 code style cleanup

Fix several errors and warnings given by checkpatch.pl:

- use of C99 // comments;

- brace not on the same line with condition in the 'switch' statement;

- printk() without KERN_* facility level;

- unnecessary braces for single-statement block;

- using simple_strtol() where strict_strtol() could be used.

In addition to these changes, also do the following:

- properly indent the 'switch' statement;

- remove needless parentheses;

- insert spaces between operator and its operands;

- replace numeric literals/expressions with the matching macros;

- remove useless #if dirctive from board_setup();

- remove unneeded numeric literal type casts;

- remove space after the type cast's closing parenthesis;

- replace spaces after the macro name with tabs in the #define directives, and
  sometimes insert spaces there;

- remove excess new lines;

- fix typos/errors, capitalize acronyms, etc. in the comments;

- make the multi-line comment style consistent with the kernel style elsewhere
  by adding empty first/last line;

- combine some comments;

- update MontaVista copyright;

- remove Pete Popov's old email address...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

3 files changed, 70 insertions, 68 deletions

diff --git a/arch/mips/au1000/pb1000/Makefile b/arch/mips/au1000/pb1000/Makefile
index daa1a50..99bbec0 100644
--- a/arch/mips/au1000/pb1000/Makefile
+++ b/arch/mips/au1000/pb1000/Makefile
@@ -1,8 +1,8 @@
 #
-#  Copyright 2000 MontaVista Software Inc.
-#  Author: MontaVista Software, Inc.
-#     	ppopov@mvista.com or source@mvista.com
+#  Copyright 2000, 2008 MontaVista Software Inc.
+#  Author: MontaVista Software, Inc. <source@mvista.com>
+#
+# Makefile for the Alchemy Semiconductor Pb1000 board.
 #
-# Makefile for the Alchemy Semiconductor PB1000 board.
 
 lib-y := init.o board_setup.o irqmap.o
diff --git a/arch/mips/au1000/pb1000/board_setup.c b/arch/mips/au1000/pb1000/board_setup.c
index 33f15ac..a06c653 100644
--- a/arch/mips/au1000/pb1000/board_setup.c
+++ b/arch/mips/au1000/pb1000/board_setup.c
@@ -1,7 +1,6 @@
 /*
- * Copyright 2000 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- *         	ppopov@mvista.com or source@mvista.com
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
  *
  *  This program is free software; you can redistribute  it and/or modify it
  *  under  the terms of  the GNU General  Public License as published by the
@@ -40,106 +39,108 @@ void __init board_setup(void)
 	u32 sys_freqctrl, sys_clksrc;
 	u32 prid = read_c0_prid();
 
-	// set AUX clock to 12MHz * 8 = 96 MHz
+	/* Set AUX clock to 12 MHz * 8 = 96 MHz */
 	au_writel(8, SYS_AUXPLL);
 	au_writel(0, SYS_PINSTATERD);
 	udelay(100);
 
 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-	/* zero and disable FREQ2 */
+	/* Zero and disable FREQ2 */
 	sys_freqctrl = au_readl(SYS_FREQCTRL0);
 	sys_freqctrl &= ~0xFFF00000;
 	au_writel(sys_freqctrl, SYS_FREQCTRL0);
 
-	/* zero and disable USBH/USBD clocks */
+	/* Zero and disable USBH/USBD clocks */
 	sys_clksrc = au_readl(SYS_CLKSRC);
-	sys_clksrc &= ~0x00007FE0;
+	sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+		        SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
 	au_writel(sys_clksrc, SYS_CLKSRC);
 
 	sys_freqctrl = au_readl(SYS_FREQCTRL0);
 	sys_freqctrl &= ~0xFFF00000;
 
 	sys_clksrc = au_readl(SYS_CLKSRC);
-	sys_clksrc &= ~0x00007FE0;
+	sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+		        SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
 
-	switch (prid & 0x000000FF)
-	{
+	switch (prid & 0x000000FF) {
 	case 0x00: /* DA */
 	case 0x01: /* HA */
 	case 0x02: /* HB */
-	/* CPU core freq to 48MHz to slow it way down... */
-	au_writel(4, SYS_CPUPLL);
+		/* CPU core freq to 48 MHz to slow it way down... */
+		au_writel(4, SYS_CPUPLL);
 
-	/*
-	 * Setup 48MHz FREQ2 from CPUPLL for USB Host
-	 */
-	/* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */
-	sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20));
-	au_writel(sys_freqctrl, SYS_FREQCTRL0);
+		/*
+		 * Setup 48 MHz FREQ2 from CPUPLL for USB Host
+		 * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
+		 */
+		sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
+		au_writel(sys_freqctrl, SYS_FREQCTRL0);
 
-	/* CPU core freq to 384MHz */
-	au_writel(0x20, SYS_CPUPLL);
+		/* CPU core freq to 384 MHz */
+		au_writel(0x20, SYS_CPUPLL);
 
-	printk("Au1000: 48MHz OHCI workaround enabled\n");
+		printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
 		break;
 
-	default:  /* HC and newer */
-	// FREQ2 = aux/2 = 48 MHz
-	sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
-	au_writel(sys_freqctrl, SYS_FREQCTRL0);
+	default: /* HC and newer */
+		/* FREQ2 = aux / 2 = 48 MHz */
+		sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+				 SYS_FC_FE2 | SYS_FC_FS2;
+		au_writel(sys_freqctrl, SYS_FREQCTRL0);
 		break;
 	}
 
 	/*
-	 * Route 48MHz FREQ2 into USB Host and/or Device
+	 * Route 48 MHz FREQ2 into USB Host and/or Device
 	 */
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-	sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
-#endif
+	sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
 	au_writel(sys_clksrc, SYS_CLKSRC);
 
-	// configure pins GPIO[14:9] as GPIO
-	pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080);
+	/* Configure pins GPIO[14:9] as GPIO */
+	pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
 
-	// 2nd USB port is USB host
-	pin_func |= 0x8000;
+	/* 2nd USB port is USB host */
+	pin_func |= SYS_PF_USB;
 
 	au_writel(pin_func, SYS_PINFUNC);
 	au_writel(0x2800, SYS_TRIOUTCLR);
 	au_writel(0x0030, SYS_OUTPUTCLR);
 #endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
 
-	// make gpio 15 an input (for interrupt line)
-	pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100);
-	// we don't need I2S, so make it available for GPIO[31:29]
-	pin_func |= (1<<5);
+	/* Make GPIO 15 an input (for interrupt line) */
+	pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
+	/* We don't need I2S, so make it available for GPIO[31:29] */
+	pin_func |= SYS_PF_I2S;
 	au_writel(pin_func, SYS_PINFUNC);
 
 	au_writel(0x8000, SYS_TRIOUTCLR);
 
-	static_cfg0 = au_readl(MEM_STCFG0) & (u32)(~0xc00);
+	static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
 	au_writel(static_cfg0, MEM_STCFG0);
 
-	// configure RCE2* for LCD
+	/* configure RCE2* for LCD */
 	au_writel(0x00000004, MEM_STCFG2);
 
-	// MEM_STTIME2
+	/* MEM_STTIME2 */
 	au_writel(0x09000000, MEM_STTIME2);
 
-	// Set 32-bit base address decoding for RCE2*
+	/* Set 32-bit base address decoding for RCE2* */
 	au_writel(0x10003ff0, MEM_STADDR2);
 
-	// PCI CPLD setup
-	// expand CE0 to cover PCI
+	/*
+	 * PCI CPLD setup
+	 * Expand CE0 to cover PCI
+	 */
 	au_writel(0x11803e40, MEM_STADDR1);
 
-	// burst visibility on
+	/* Burst visibility on */
 	au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
 
-	au_writel(0x83, MEM_STCFG1);         // ewait enabled, flash timing
-	au_writel(0x33030a10, MEM_STTIME1);   // slower timing for FPGA
+	au_writel(0x83, MEM_STCFG1);	     /* ewait enabled, flash timing */
+	au_writel(0x33030a10, MEM_STTIME1);  /* slower timing for FPGA */
 
-	/* setup the static bus controller */
+	/* Setup the static bus controller */
 	au_writel(0x00000002, MEM_STCFG3);  /* type = PCMCIA */
 	au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
 	au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
@@ -151,17 +152,20 @@ void __init board_setup(void)
 	au_sync_delay(1);
 #endif
 
-	/* Enable Au1000 BCLK switching - note: sed1356 must not use
-	 * its BCLK (Au1000 LCLK) for any timings */
-	switch (prid & 0x000000FF)
-	{
+	/*
+	 * Enable Au1000 BCLK switching - note: sed1356 must not use
+	 * its BCLK (Au1000 LCLK) for any timings
+	 */
+	switch (prid & 0x000000FF) {
 	case 0x00: /* DA */
 	case 0x01: /* HA */
 	case 0x02: /* HB */
 		break;
 	default:  /* HC and newer */
-		/* Enable sys bus clock divider when IDLE state or no bus
-		   activity. */
+		/*
+		 * Enable sys bus clock divider when IDLE state or no bus
+		 * activity.
+		 */
 		au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
 		break;
 	}
diff --git a/arch/mips/au1000/pb1000/init.c b/arch/mips/au1000/pb1000/init.c
index 549447d..3837365 100644
--- a/arch/mips/au1000/pb1000/init.c
+++ b/arch/mips/au1000/pb1000/init.c
@@ -1,10 +1,9 @@
 /*
  * BRIEF MODULE DESCRIPTION
- *	PB1000 board setup
+ *	Pb1000 board setup
  *
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- *         	ppopov@mvista.com or source@mvista.com
+ * Copyright 2001, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
  *
  *  This program is free software; you can redistribute  it and/or modify it
  *  under  the terms of  the GNU General  Public License as published by the
@@ -44,16 +43,15 @@ void __init prom_init(void)
 	unsigned char *memsize_str;
 	unsigned long memsize;
 
-	prom_argc = (int) fw_arg0;
-	prom_argv = (char **) fw_arg1;
-	prom_envp = (char **) fw_arg2;
+	prom_argc = (int)fw_arg0;
+	prom_argv = (char **)fw_arg1;
+	prom_envp = (char **)fw_arg2;
 
 	prom_init_cmdline();
 	memsize_str = prom_getenv("memsize");
-	if (!memsize_str) {
+	if (!memsize_str)
 		memsize = 0x04000000;
-	} else {
-		memsize = simple_strtol(memsize_str, NULL, 0);
-	}
+	else
+		memsize = strict_strtol(memsize_str, 0, NULL);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }