diff options
| -rw-r--r-- | arch/sh/boards/mach-se/7751/Makefile | 2 | ||||
| -rw-r--r-- | arch/sh/boards/mach-se/7751/pci.c | 150 | ||||
| -rw-r--r-- | arch/sh/drivers/pci/Makefile | 1 | ||||
| -rw-r--r-- | arch/sh/drivers/pci/fixups-se7751.c | 111 |
4 files changed, 112 insertions, 152 deletions
diff --git a/arch/sh/boards/mach-se/7751/Makefile b/arch/sh/boards/mach-se/7751/Makefile index dbc29f3..e6f4341 100644 --- a/arch/sh/boards/mach-se/7751/Makefile +++ b/arch/sh/boards/mach-se/7751/Makefile @@ -3,5 +3,3 @@ # obj-y := setup.o io.o irq.o - -obj-$(CONFIG_PCI) += pci.o diff --git a/arch/sh/boards/mach-se/7751/pci.c b/arch/sh/boards/mach-se/7751/pci.c deleted file mode 100644 index 9ec64a4..0000000 --- a/arch/sh/boards/mach-se/7751/pci.c +++ /dev/null @@ -1,150 +0,0 @@ -/* - * linux/arch/sh/boards/se/7751/pci.c - * - * Author: Ian DaSilva (idasilva@mvista.com) - * - * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * PCI initialization for the Hitachi SH7751 Solution Engine board (MS7751SE01) - */ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/pci.h> - -#include <asm/io.h> -#include "../../../drivers/pci/pci-sh7751.h" - -#define PCIMCR_MRSET_OFF 0xBFFFFFFF -#define PCIMCR_RFSH_OFF 0xFFFFFFFB - -/* - * Only long word accesses of the PCIC's internal local registers and the - * configuration registers from the CPU is supported. - */ -#define PCIC_WRITE(x,v) writel((v), PCI_REG(x)) -#define PCIC_READ(x) readl(PCI_REG(x)) - -#define xPCIBIOS_MIN_IO board_pci_channels->io_resource->start -#define xPCIBIOS_MIN_MEM board_pci_channels->mem_resource->start - -/* - * Description: This function sets up and initializes the pcic, sets - * up the BARS, maps the DRAM into the address space etc, etc. - */ -int __init pcibios_init_platform(void) -{ - unsigned long bcr1, wcr1, wcr2, wcr3, mcr; - unsigned short bcr2; - - /* - * Initialize the slave bus controller on the pcic. The values used - * here should not be hardcoded, but they should be taken from the bsc - * on the processor, to make this function as generic as possible. - * (i.e. Another sbc may usr different SDRAM timing settings -- in order - * for the pcic to work, its settings need to be exactly the same.) - */ - bcr1 = (*(volatile unsigned long*)(SH7751_BCR1)); - bcr2 = (*(volatile unsigned short*)(SH7751_BCR2)); - wcr1 = (*(volatile unsigned long*)(SH7751_WCR1)); - wcr2 = (*(volatile unsigned long*)(SH7751_WCR2)); - wcr3 = (*(volatile unsigned long*)(SH7751_WCR3)); - mcr = (*(volatile unsigned long*)(SH7751_MCR)); - - bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */ - (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1; - - bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ - PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */ - PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */ - PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */ - PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */ - PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */ - mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; - PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */ - - - /* Enable all interrupts, so we know what to fix */ - PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff); - PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f); - - /* Set up standard PCI config registers */ - PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */ - PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */ - PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */ - PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */ - PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */ - PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */ - PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */ - PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */ - PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */ - PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */ - - /* Now turn it on... */ - PCIC_WRITE(SH7751_PCICR, 0xa5000001); - - /* - * Set PCIMBR and PCIIOBR here, assuming a single window - * (16M MEM, 256K IO) is enough. If a larger space is - * needed, the readx/writex and inx/outx functions will - * have to do more (e.g. setting registers for each call). - */ - - /* - * Set the MBR so PCI address is one-to-one with window, - * meaning all calls go straight through... use BUG_ON to - * catch erroneous assumption. - */ - BUG_ON(xPCIBIOS_MIN_MEM != SH7751_PCI_MEMORY_BASE); - - PCIC_WRITE(SH7751_PCIMBR, xPCIBIOS_MIN_MEM); - - /* Set IOBR for window containing area specified in pci.h */ - PCIC_WRITE(SH7751_PCIIOBR, (xPCIBIOS_MIN_IO & SH7751_PCIIOBR_MASK)); - - /* All done, may as well say so... */ - printk("SH7751 PCI: Finished initialization of the PCI controller\n"); - - return 1; -} - -int __init pcibios_map_platform_irq(u8 slot, u8 pin) -{ - switch (slot) { - case 0: return 13; - case 1: return 13; /* AMD Ethernet controller */ - case 2: return -1; - case 3: return -1; - case 4: return -1; - default: - printk("PCI: Bad IRQ mapping request for slot %d\n", slot); - return -1; - } -} - -static struct resource sh7751_io_resource = { - .name = "SH7751 IO", - .start = SH7751_PCI_IO_BASE, - .end = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7751_mem_resource = { - .name = "SH7751 mem", - .start = SH7751_PCI_MEMORY_BASE, - .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -extern struct pci_ops sh7751_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &sh7751_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; - diff --git a/arch/sh/drivers/pci/Makefile b/arch/sh/drivers/pci/Makefile index fbebd73..e388a70 100644 --- a/arch/sh/drivers/pci/Makefile +++ b/arch/sh/drivers/pci/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_CPU_SH5) += pci-sh5.o ops-sh5.o obj-$(CONFIG_SH_DREAMCAST) += ops-dreamcast.o fixups-dreamcast.o \ pci-dreamcast.o obj-$(CONFIG_SH_SECUREEDGE5410) += fixups-snapgear.o +obj-$(CONFIG_SH_7751_SOLUTION_ENGINE) += fixups-se7751.o obj-$(CONFIG_SH_RTS7751R2D) += fixups-rts7751r2d.o obj-$(CONFIG_SH_SH03) += fixups-sh03.o obj-$(CONFIG_SH_HIGHLANDER) += fixups-r7780rp.o diff --git a/arch/sh/drivers/pci/fixups-se7751.c b/arch/sh/drivers/pci/fixups-se7751.c new file mode 100644 index 0000000..475fa9f --- /dev/null +++ b/arch/sh/drivers/pci/fixups-se7751.c @@ -0,0 +1,111 @@ +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/io.h> +#include "pci-sh4.h" + +int __init pcibios_map_platform_irq(u8 slot, u8 pin) +{ + switch (slot) { + case 0: return 13; + case 1: return 13; /* AMD Ethernet controller */ + case 2: return -1; + case 3: return -1; + case 4: return -1; + default: + printk("PCI: Bad IRQ mapping request for slot %d\n", slot); + return -1; + } +} + +#define PCIMCR_MRSET_OFF 0xBFFFFFFF +#define PCIMCR_RFSH_OFF 0xFFFFFFFB + +/* + * Only long word accesses of the PCIC's internal local registers and the + * configuration registers from the CPU is supported. + */ +#define PCIC_WRITE(x,v) writel((v), PCI_REG(x)) +#define PCIC_READ(x) readl(PCI_REG(x)) + +/* + * Description: This function sets up and initializes the pcic, sets + * up the BARS, maps the DRAM into the address space etc, etc. + */ +int pci_fixup_pcic(struct pci_channel *chan) +{ + unsigned long bcr1, wcr1, wcr2, wcr3, mcr; + unsigned short bcr2; + + /* + * Initialize the slave bus controller on the pcic. The values used + * here should not be hardcoded, but they should be taken from the bsc + * on the processor, to make this function as generic as possible. + * (i.e. Another sbc may usr different SDRAM timing settings -- in order + * for the pcic to work, its settings need to be exactly the same.) + */ + bcr1 = (*(volatile unsigned long*)(SH7751_BCR1)); + bcr2 = (*(volatile unsigned short*)(SH7751_BCR2)); + wcr1 = (*(volatile unsigned long*)(SH7751_WCR1)); + wcr2 = (*(volatile unsigned long*)(SH7751_WCR2)); + wcr3 = (*(volatile unsigned long*)(SH7751_WCR3)); + mcr = (*(volatile unsigned long*)(SH7751_MCR)); + + bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */ + (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1; + + bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ + PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */ + PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */ + PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */ + PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */ + PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */ + mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; + PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */ + + + /* Enable all interrupts, so we know what to fix */ + PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff); + PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f); + + /* Set up standard PCI config registers */ + PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */ + PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */ + PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */ + PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */ + PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */ + PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */ + PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */ + PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */ + PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */ + PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */ + + /* Now turn it on... */ + PCIC_WRITE(SH7751_PCICR, 0xa5000001); + + /* + * Set PCIMBR and PCIIOBR here, assuming a single window + * (16M MEM, 256K IO) is enough. If a larger space is + * needed, the readx/writex and inx/outx functions will + * have to do more (e.g. setting registers for each call). + */ + + /* + * Set the MBR so PCI address is one-to-one with window, + * meaning all calls go straight through... use BUG_ON to + * catch erroneous assumption. + */ + BUG_ON(chan->mem_resource->start != SH7751_PCI_MEMORY_BASE); + + PCIC_WRITE(SH7751_PCIMBR, chan->mem_resource->start); + + /* Set IOBR for window containing area specified in pci.h */ + PCIC_WRITE(SH7751_PCIIOBR, (chan->io_resource->start & SH7751_PCIIOBR_MASK)); + + /* All done, may as well say so... */ + printk("SH7751 PCI: Finished initialization of the PCI controller\n"); + + return 1; +} |