diff options
Diffstat (limited to 'arch/blackfin/mach-bf527/include/mach/defBF52x_base.h')
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/defBF52x_base.h | 186 |
1 files changed, 0 insertions, 186 deletions
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h index b9dbb73..8b18b53 100644 --- a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h +++ b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h @@ -586,58 +586,6 @@ ** modifier UNLESS the lower order bits are saved and ORed back in when ** the macro is used. *************************************************************************************/ -/* -** ********************* PLL AND RESET MASKS ****************************************/ -/* PLL_CTL Masks */ -#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */ -#define PLL_OFF 0x0002 /* PLL Not Powered */ -#define STOPCK 0x0008 /* Core Clock Off */ -#define PDWN 0x0020 /* Enter Deep Sleep Mode */ -#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */ -#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */ -#define BYPASS 0x0100 /* Bypass the PLL */ -#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */ -/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */ -#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */ - -/* PLL_DIV Masks */ -#define SSEL 0x000F /* System Select */ -#define CSEL 0x0030 /* Core Select */ -#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */ -#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */ -#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */ -#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */ -/* PLL_DIV Macros */ -#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */ - -/* VR_CTL Masks */ -#define FREQ 0x3000 /* Switching Oscillator Frequency For Regulator */ -#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */ - -#define VLEV 0x00F0 /* Internal Voltage Level */ -#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */ -#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */ -#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */ -#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */ -#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */ -#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */ -#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */ -#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */ -#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */ -#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */ - -#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */ -#define USBWE 0x0200 /* Enable USB Wakeup From Hibernate */ -#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */ -#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */ -#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */ -#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */ - -/* PLL_STAT Masks */ -#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */ -#define FULL_ON 0x0002 /* Processor In Full On Mode */ -#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */ -#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */ /* CHIPID Masks */ #define CHIPID_VERSION 0xF0000000 @@ -757,66 +705,6 @@ #define IWR_DISABLE(x) (0xFFFFFFFF ^ (1 << ((x)&0x1F))) /* Wakeup Disable Peripheral #x */ -/* ********* WATCHDOG TIMER MASKS ******************** */ - -/* Watchdog Timer WDOG_CTL Register Masks */ - -#define WDEV(x) (((x)<<1) & 0x0006) /* event generated on roll over */ -#define WDEV_RESET 0x0000 /* generate reset event on roll over */ -#define WDEV_NMI 0x0002 /* generate NMI event on roll over */ -#define WDEV_GPI 0x0004 /* generate GP IRQ on roll over */ -#define WDEV_NONE 0x0006 /* no event on roll over */ -#define WDEN 0x0FF0 /* enable watchdog */ -#define WDDIS 0x0AD0 /* disable watchdog */ -#define WDRO 0x8000 /* watchdog rolled over latch */ - -/* depreciated WDOG_CTL Register Masks for legacy code */ - - -#define ICTL WDEV -#define ENABLE_RESET WDEV_RESET -#define WDOG_RESET WDEV_RESET -#define ENABLE_NMI WDEV_NMI -#define WDOG_NMI WDEV_NMI -#define ENABLE_GPI WDEV_GPI -#define WDOG_GPI WDEV_GPI -#define DISABLE_EVT WDEV_NONE -#define WDOG_NONE WDEV_NONE - -#define TMR_EN WDEN -#define TMR_DIS WDDIS -#define TRO WDRO -#define ICTL_P0 0x01 - #define ICTL_P1 0x02 -#define TRO_P 0x0F - - - -/* *************** REAL TIME CLOCK MASKS **************************/ -/* RTC_STAT and RTC_ALARM Masks */ -#define RTC_SEC 0x0000003F /* Real-Time Clock Seconds */ -#define RTC_MIN 0x00000FC0 /* Real-Time Clock Minutes */ -#define RTC_HR 0x0001F000 /* Real-Time Clock Hours */ -#define RTC_DAY 0xFFFE0000 /* Real-Time Clock Days */ - -/* RTC_ALARM Macro z=day y=hr x=min w=sec */ -#define SET_ALARM(z,y,x,w) ((((z)&0x7FFF)<<0x11)|(((y)&0x1F)<<0xC)|(((x)&0x3F)<<0x6)|((w)&0x3F)) - -/* RTC_ICTL and RTC_ISTAT Masks */ -#define STOPWATCH 0x0001 /* Stopwatch Interrupt Enable */ -#define ALARM 0x0002 /* Alarm Interrupt Enable */ -#define SECOND 0x0004 /* Seconds (1 Hz) Interrupt Enable */ -#define MINUTE 0x0008 /* Minutes Interrupt Enable */ -#define HOUR 0x0010 /* Hours Interrupt Enable */ -#define DAY 0x0020 /* 24 Hours (Days) Interrupt Enable */ -#define DAY_ALARM 0x0040 /* Day Alarm (Day, Hour, Minute, Second) Interrupt Enable */ -#define WRITE_PENDING 0x4000 /* Write Pending Status */ -#define WRITE_COMPLETE 0x8000 /* Write Complete Interrupt Enable */ - -/* RTC_FAST / RTC_PREN Mask */ -#define PREN 0x0001 /* Enable Prescaler, RTC Runs @1 Hz */ - - /* ************** UART CONTROLLER MASKS *************************/ /* UARTx_LCR Masks */ #define WLS(x) (((x)-5) & 0x03) /* Word Length Select */ @@ -1381,33 +1269,6 @@ /* ************************** DMA CONTROLLER MASKS ********************************/ -/* DMAx_CONFIG, MDMA_yy_CONFIG Masks */ -#define DMAEN 0x0001 /* DMA Channel Enable */ -#define WNR 0x0002 /* Channel Direction (W/R*) */ -#define WDSIZE_8 0x0000 /* Transfer Word Size = 8 */ -#define WDSIZE_16 0x0004 /* Transfer Word Size = 16 */ -#define WDSIZE_32 0x0008 /* Transfer Word Size = 32 */ -#define DMA2D 0x0010 /* DMA Mode (2D/1D*) */ -#define RESTART 0x0020 /* DMA Buffer Clear */ -#define DI_SEL 0x0040 /* Data Interrupt Timing Select */ -#define DI_EN 0x0080 /* Data Interrupt Enable */ -#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */ -#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */ -#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */ -#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */ -#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */ -#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */ -#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */ -#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */ -#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */ -#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */ -#define NDSIZE 0x0900 /* Next Descriptor Size */ -#define DMAFLOW 0x7000 /* Flow Control */ -#define DMAFLOW_STOP 0x0000 /* Stop Mode */ -#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */ -#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */ -#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */ -#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */ /* DMAx_PERIPHERAL_MAP, MDMA_yy_PERIPHERAL_MAP Masks */ #define CTYPE 0x0040 /* DMA Channel Type Indicator (Memory/Peripheral*) */ @@ -1425,13 +1286,6 @@ #define PMAP_UART1RX 0xA000 /* UART1 Port Receive DMA */ #define PMAP_UART1TX 0xB000 /* UART1 Port Transmit DMA */ -/* DMAx_IRQ_STATUS, MDMA_yy_IRQ_STATUS Masks */ -#define DMA_DONE 0x0001 /* DMA Completion Interrupt Status */ -#define DMA_ERR 0x0002 /* DMA Error Interrupt Status */ -#define DFETCH 0x0004 /* DMA Descriptor Fetch Indicator */ -#define DMA_RUN 0x0008 /* DMA Channel Running Indicator */ - - /* ************ PARALLEL PERIPHERAL INTERFACE (PPI) MASKS *************/ /* PPI_CONTROL Masks */ #define PORT_EN 0x0001 /* PPI Port Enable */ @@ -1843,46 +1697,6 @@ #define BNDMODE_CAPT 0x2000 /* boundary capture mode */ #define BNDMODE_AEXT 0x3000 /* boundary auto-extend mode */ -/* Bit masks for OTP_CONTROL */ - -#define FUSE_FADDR 0x1ff /* OTP/Fuse Address */ -#define FIEN 0x800 /* OTP/Fuse Interrupt Enable */ -#define nFIEN 0x0 -#define FTESTDEC 0x1000 /* OTP/Fuse Test Decoder */ -#define nFTESTDEC 0x0 -#define FWRTEST 0x2000 /* OTP/Fuse Write Test */ -#define nFWRTEST 0x0 -#define FRDEN 0x4000 /* OTP/Fuse Read Enable */ -#define nFRDEN 0x0 -#define FWREN 0x8000 /* OTP/Fuse Write Enable */ -#define nFWREN 0x0 - -/* Bit masks for OTP_BEN */ - -#define FBEN 0xffff /* OTP/Fuse Byte Enable */ - -/* Bit masks for OTP_STATUS */ - -#define FCOMP 0x1 /* OTP/Fuse Access Complete */ -#define nFCOMP 0x0 -#define FERROR 0x2 /* OTP/Fuse Access Error */ -#define nFERROR 0x0 -#define MMRGLOAD 0x10 /* Memory Mapped Register Gasket Load */ -#define nMMRGLOAD 0x0 -#define MMRGLOCK 0x20 /* Memory Mapped Register Gasket Lock */ -#define nMMRGLOCK 0x0 -#define FPGMEN 0x40 /* OTP/Fuse Program Enable */ -#define nFPGMEN 0x0 - -/* Bit masks for OTP_TIMING */ - -#define USECDIV 0xff /* Micro Second Divider */ -#define READACC 0x7f00 /* Read Access Time */ -#define CPUMPRL 0x38000 /* Charge Pump Release Time */ -#define CPUMPSU 0xc0000 /* Charge Pump Setup Time */ -#define CPUMPHD 0xf00000 /* Charge Pump Hold Time */ -#define PGMTIME 0xff000000 /* Program Time */ - /* Bit masks for SECURE_SYSSWT */ #define EMUDABL 0x1 /* Emulation Disable. */ |