aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/net/wimax/i2400m/control.c16
-rw-r--r--drivers/net/wimax/i2400m/debugfs.c2
-rw-r--r--drivers/net/wimax/i2400m/driver.c500
-rw-r--r--drivers/net/wimax/i2400m/fw.c886
-rw-r--r--drivers/net/wimax/i2400m/i2400m-sdio.h16
-rw-r--r--drivers/net/wimax/i2400m/i2400m-usb.h16
-rw-r--r--drivers/net/wimax/i2400m/i2400m.h209
-rw-r--r--drivers/net/wimax/i2400m/netdev.c127
-rw-r--r--drivers/net/wimax/i2400m/rx.c170
-rw-r--r--drivers/net/wimax/i2400m/sdio-fw.c11
-rw-r--r--drivers/net/wimax/i2400m/sdio-rx.c42
-rw-r--r--drivers/net/wimax/i2400m/sdio-tx.c5
-rw-r--r--drivers/net/wimax/i2400m/sdio.c205
-rw-r--r--drivers/net/wimax/i2400m/tx.c20
-rw-r--r--drivers/net/wimax/i2400m/usb-fw.c37
-rw-r--r--drivers/net/wimax/i2400m/usb-notif.c35
-rw-r--r--drivers/net/wimax/i2400m/usb-rx.c60
-rw-r--r--drivers/net/wimax/i2400m/usb-tx.c61
-rw-r--r--drivers/net/wimax/i2400m/usb.c189
19 files changed, 2001 insertions, 606 deletions
diff --git a/drivers/net/wimax/i2400m/control.c b/drivers/net/wimax/i2400m/control.c
index 0730868..9449455 100644
--- a/drivers/net/wimax/i2400m/control.c
+++ b/drivers/net/wimax/i2400m/control.c
@@ -54,7 +54,7 @@
* i2400m_set_init_config()
* i2400m_cmd_get_state()
* i2400m_dev_shutdown() Called by i2400m_dev_stop()
- * i2400m->bus_reset()
+ * i2400m_reset()
*
* i2400m_{cmd,get,set}_*()
* i2400m_msg_to_dev()
@@ -82,6 +82,13 @@
#define D_SUBMODULE control
#include "debug-levels.h"
+int i2400m_passive_mode; /* 0 (passive mode disabled) by default */
+module_param_named(passive_mode, i2400m_passive_mode, int, 0644);
+MODULE_PARM_DESC(passive_mode,
+ "If true, the driver will not do any device setup "
+ "and leave it up to user space, who must be properly "
+ "setup.");
+
/*
* Return if a TLV is of a give type and size
@@ -263,7 +270,7 @@ int i2400m_msg_check_status(const struct i2400m_l3l4_hdr *l3l4_hdr,
if (status == 0)
return 0;
- if (status > ARRAY_SIZE(ms_to_errno)) {
+ if (status >= ARRAY_SIZE(ms_to_errno)) {
str = "unknown status code";
result = -EBADR;
} else {
@@ -336,7 +343,7 @@ void i2400m_report_tlv_system_state(struct i2400m *i2400m,
/* Huh? just in case, shut it down */
dev_err(dev, "HW BUG? unknown state %u: shutting down\n",
i2400m_state);
- i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+ i2400m_reset(i2400m, I2400M_RT_WARM);
break;
};
d_fnend(3, dev, "(i2400m %p ss %p [%u]) = void\n",
@@ -1335,6 +1342,8 @@ int i2400m_dev_initialize(struct i2400m *i2400m)
unsigned argc = 0;
d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+ if (i2400m_passive_mode)
+ goto out_passive;
/* Disable idle mode? (enabled by default) */
if (i2400m_idle_mode_disabled) {
if (i2400m_le_v1_3(i2400m)) {
@@ -1377,6 +1386,7 @@ int i2400m_dev_initialize(struct i2400m *i2400m)
result = i2400m_set_init_config(i2400m, args, argc);
if (result < 0)
goto error;
+out_passive:
/*
* Update state: Here it just calls a get state; parsing the
* result (System State TLV and RF Status TLV [done in the rx
diff --git a/drivers/net/wimax/i2400m/debugfs.c b/drivers/net/wimax/i2400m/debugfs.c
index 9b81af3..b1aec3e 100644
--- a/drivers/net/wimax/i2400m/debugfs.c
+++ b/drivers/net/wimax/i2400m/debugfs.c
@@ -214,7 +214,7 @@ int debugfs_i2400m_reset_set(void *data, u64 val)
case I2400M_RT_WARM:
case I2400M_RT_COLD:
case I2400M_RT_BUS:
- result = i2400m->bus_reset(i2400m, rt);
+ result = i2400m_reset(i2400m, rt);
if (result >= 0)
result = 0;
default:
diff --git a/drivers/net/wimax/i2400m/driver.c b/drivers/net/wimax/i2400m/driver.c
index 304f044..96a615f 100644
--- a/drivers/net/wimax/i2400m/driver.c
+++ b/drivers/net/wimax/i2400m/driver.c
@@ -41,8 +41,10 @@
* __i2400m_dev_start()
*
* i2400m_setup()
+ * i2400m->bus_setup()
* i2400m_bootrom_init()
* register_netdev()
+ * wimax_dev_add()
* i2400m_dev_start()
* __i2400m_dev_start()
* i2400m_dev_bootstrap()
@@ -50,15 +52,15 @@
* i2400m->bus_dev_start()
* i2400m_firmware_check()
* i2400m_check_mac_addr()
- * wimax_dev_add()
*
* i2400m_release()
- * wimax_dev_rm()
* i2400m_dev_stop()
* __i2400m_dev_stop()
* i2400m_dev_shutdown()
* i2400m->bus_dev_stop()
* i2400m_tx_release()
+ * i2400m->bus_release()
+ * wimax_dev_rm()
* unregister_netdev()
*/
#include "i2400m.h"
@@ -66,6 +68,7 @@
#include <linux/wimax/i2400m.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
+#include <linux/suspend.h>
#define D_SUBMODULE driver
#include "debug-levels.h"
@@ -90,76 +93,39 @@ MODULE_PARM_DESC(power_save_disabled,
"False by default (so the device is told to do power "
"saving).");
-/**
- * i2400m_queue_work - schedule work on a i2400m's queue
- *
- * @i2400m: device descriptor
- *
- * @fn: function to run to execute work. It gets passed a 'struct
- * work_struct' that is wrapped in a 'struct i2400m_work'. Once
- * done, you have to (1) i2400m_put(i2400m_work->i2400m) and then
- * (2) kfree(i2400m_work).
- *
- * @gfp_flags: GFP flags for memory allocation.
- *
- * @pl: pointer to a payload buffer that you want to pass to the _work
- * function. Use this to pack (for example) a struct with extra
- * arguments.
- *
- * @pl_size: size of the payload buffer.
- *
- * We do this quite often, so this just saves typing; allocate a
- * wrapper for a i2400m, get a ref to it, pack arguments and launch
- * the work.
- *
- * A usual workflow is:
- *
- * struct my_work_args {
- * void *something;
- * int whatever;
- * };
- * ...
- *
- * struct my_work_args my_args = {
- * .something = FOO,
- * .whaetever = BLAH
- * };
- * i2400m_queue_work(i2400m, 1, my_work_function, GFP_KERNEL,
- * &args, sizeof(args))
- *
- * And now the work function can unpack the arguments and call the
- * real function (or do the job itself):
- *
- * static
- * void my_work_fn((struct work_struct *ws)
- * {
- * struct i2400m_work *iw =
- * container_of(ws, struct i2400m_work, ws);
- * struct my_work_args *my_args = (void *) iw->pl;
- *
- * my_work(iw->i2400m, my_args->something, my_args->whatevert);
- * }
- */
-int i2400m_queue_work(struct i2400m *i2400m,
- void (*fn)(struct work_struct *), gfp_t gfp_flags,
- const void *pl, size_t pl_size)
+static char i2400m_debug_params[128];
+module_param_string(debug, i2400m_debug_params, sizeof(i2400m_debug_params),
+ 0644);
+MODULE_PARM_DESC(debug,
+ "String of space-separated NAME:VALUE pairs, where NAMEs "
+ "are the different debug submodules and VALUE are the "
+ "initial debug value to set.");
+
+static char i2400m_barkers_params[128];
+module_param_string(barkers, i2400m_barkers_params,
+ sizeof(i2400m_barkers_params), 0644);
+MODULE_PARM_DESC(barkers,
+ "String of comma-separated 32-bit values; each is "
+ "recognized as the value the device sends as a reboot "
+ "signal; values are appended to a list--setting one value "
+ "as zero cleans the existing list and starts a new one.");
+
+static
+struct i2400m_work *__i2400m_work_setup(
+ struct i2400m *i2400m, void (*fn)(struct work_struct *),
+ gfp_t gfp_flags, const void *pl, size_t pl_size)
{
- int result;
struct i2400m_work *iw;
- BUG_ON(i2400m->work_queue == NULL);
- result = -ENOMEM;
iw = kzalloc(sizeof(*iw) + pl_size, gfp_flags);
if (iw == NULL)
- goto error_kzalloc;
+ return NULL;
iw->i2400m = i2400m_get(i2400m);
+ iw->pl_size = pl_size;
memcpy(iw->pl, pl, pl_size);
INIT_WORK(&iw->ws, fn);
- result = queue_work(i2400m->work_queue, &iw->ws);
-error_kzalloc:
- return result;
+ return iw;
}
-EXPORT_SYMBOL_GPL(i2400m_queue_work);
/*
@@ -175,21 +141,19 @@ EXPORT_SYMBOL_GPL(i2400m_queue_work);
* it should not happen.
*/
int i2400m_schedule_work(struct i2400m *i2400m,
- void (*fn)(struct work_struct *), gfp_t gfp_flags)
+ void (*fn)(struct work_struct *), gfp_t gfp_flags,
+ const void *pl, size_t pl_size)
{
int result;
struct i2400m_work *iw;
result = -ENOMEM;
- iw = kzalloc(sizeof(*iw), gfp_flags);
- if (iw == NULL)
- goto error_kzalloc;
- iw->i2400m = i2400m_get(i2400m);
- INIT_WORK(&iw->ws, fn);
- result = schedule_work(&iw->ws);
- if (result == 0)
- result = -ENXIO;
-error_kzalloc:
+ iw = __i2400m_work_setup(i2400m, fn, gfp_flags, pl, pl_size);
+ if (iw != NULL) {
+ result = schedule_work(&iw->ws);
+ if (WARN_ON(result == 0))
+ result = -ENXIO;
+ }
return result;
}
@@ -291,7 +255,7 @@ int i2400m_op_reset(struct wimax_dev *wimax_dev)
mutex_lock(&i2400m->init_mutex);
i2400m->reset_ctx = &ctx;
mutex_unlock(&i2400m->init_mutex);
- result = i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+ result = i2400m_reset(i2400m, I2400M_RT_WARM);
if (result < 0)
goto out;
result = wait_for_completion_timeout(&ctx.completion, 4*HZ);
@@ -420,9 +384,15 @@ retry:
dev_err(dev, "cannot create workqueue\n");
goto error_create_workqueue;
}
- result = i2400m->bus_dev_start(i2400m);
- if (result < 0)
- goto error_bus_dev_start;
+ if (i2400m->bus_dev_start) {
+ result = i2400m->bus_dev_start(i2400m);
+ if (result < 0)
+ goto error_bus_dev_start;
+ }
+ i2400m->ready = 1;
+ wmb(); /* see i2400m->ready's documentation */
+ /* process pending reports from the device */
+ queue_work(i2400m->work_queue, &i2400m->rx_report_ws);
result = i2400m_firmware_check(i2400m); /* fw versions ok? */
if (result < 0)
goto error_fw_check;
@@ -430,8 +400,6 @@ retry:
result = i2400m_check_mac_addr(i2400m);
if (result < 0)
goto error_check_mac_addr;
- i2400m->ready = 1;
- wimax_state_change(wimax_dev, WIMAX_ST_UNINITIALIZED);
result = i2400m_dev_initialize(i2400m);
if (result < 0)
goto error_dev_initialize;
@@ -443,8 +411,12 @@ retry:
error_dev_initialize:
error_check_mac_addr:
+ i2400m->ready = 0;
+ wmb(); /* see i2400m->ready's documentation */
+ flush_workqueue(i2400m->work_queue);
error_fw_check:
- i2400m->bus_dev_stop(i2400m);
+ if (i2400m->bus_dev_stop)
+ i2400m->bus_dev_stop(i2400m);
error_bus_dev_start:
destroy_workqueue(i2400m->work_queue);
error_create_workqueue:
@@ -466,11 +438,15 @@ error_bootstrap:
static
int i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri bm_flags)
{
- int result;
+ int result = 0;
mutex_lock(&i2400m->init_mutex); /* Well, start the device */
- result = __i2400m_dev_start(i2400m, bm_flags);
- if (result >= 0)
- i2400m->updown = 1;
+ if (i2400m->updown == 0) {
+ result = __i2400m_dev_start(i2400m, bm_flags);
+ if (result >= 0) {
+ i2400m->updown = 1;
+ wmb(); /* see i2400m->updown's documentation */
+ }
+ }
mutex_unlock(&i2400m->init_mutex);
return result;
}
@@ -495,9 +471,20 @@ void __i2400m_dev_stop(struct i2400m *i2400m)
d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
wimax_state_change(wimax_dev, __WIMAX_ST_QUIESCING);
+ i2400m_msg_to_dev_cancel_wait(i2400m, -EL3RST);
+ complete(&i2400m->msg_completion);
+ i2400m_net_wake_stop(i2400m);
i2400m_dev_shutdown(i2400m);
- i2400m->ready = 0;
- i2400m->bus_dev_stop(i2400m);
+ /*
+ * Make sure no report hooks are running *before* we stop the
+ * communication infrastructure with the device.
+ */
+ i2400m->ready = 0; /* nobody can queue work anymore */
+ wmb(); /* see i2400m->ready's documentation */
+ flush_workqueue(i2400m->work_queue);
+
+ if (i2400m->bus_dev_stop)
+ i2400m->bus_dev_stop(i2400m);
destroy_workqueue(i2400m->work_queue);
i2400m_rx_release(i2400m);
i2400m_tx_release(i2400m);
@@ -518,12 +505,139 @@ void i2400m_dev_stop(struct i2400m *i2400m)
if (i2400m->updown) {
__i2400m_dev_stop(i2400m);
i2400m->updown = 0;
+ wmb(); /* see i2400m->updown's documentation */
}
mutex_unlock(&i2400m->init_mutex);
}
/*
+ * Listen to PM events to cache the firmware before suspend/hibernation
+ *
+ * When the device comes out of suspend, it might go into reset and
+ * firmware has to be uploaded again. At resume, most of the times, we
+ * can't load firmware images from disk, so we need to cache it.
+ *
+ * i2400m_fw_cache() will allocate a kobject and attach the firmware
+ * to it; that way we don't have to worry too much about the fw loader
+ * hitting a race condition.
+ *
+ * Note: modus operandi stolen from the Orinoco driver; thx.
+ */
+static
+int i2400m_pm_notifier(struct notifier_block *notifier,
+ unsigned long pm_event,
+ void *unused)
+{
+ struct i2400m *i2400m =
+ container_of(notifier, struct i2400m, pm_notifier);
+ struct device *dev = i2400m_dev(i2400m);
+
+ d_fnstart(3, dev, "(i2400m %p pm_event %lx)\n", i2400m, pm_event);
+ switch (pm_event) {
+ case PM_HIBERNATION_PREPARE:
+ case PM_SUSPEND_PREPARE:
+ i2400m_fw_cache(i2400m);
+ break;
+ case PM_POST_RESTORE:
+ /* Restore from hibernation failed. We need to clean
+ * up in exactly the same way, so fall through. */
+ case PM_POST_HIBERNATION:
+ case PM_POST_SUSPEND:
+ i2400m_fw_uncache(i2400m);
+ break;
+
+ case PM_RESTORE_PREPARE:
+ default:
+ break;
+ }
+ d_fnend(3, dev, "(i2400m %p pm_event %lx) = void\n", i2400m, pm_event);
+ return NOTIFY_DONE;
+}
+
+
+/*
+ * pre-reset is called before a device is going on reset
+ *
+ * This has to be followed by a call to i2400m_post_reset(), otherwise
+ * bad things might happen.
+ */
+int i2400m_pre_reset(struct i2400m *i2400m)
+{
+ int result;
+ struct device *dev = i2400m_dev(i2400m);
+
+ d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+ d_printf(1, dev, "pre-reset shut down\n");
+
+ result = 0;
+ mutex_lock(&i2400m->init_mutex);
+ if (i2400m->updown) {
+ netif_tx_disable(i2400m->wimax_dev.net_dev);
+ __i2400m_dev_stop(i2400m);
+ result = 0;
+ /* down't set updown to zero -- this way
+ * post_reset can restore properly */
+ }
+ mutex_unlock(&i2400m->init_mutex);
+ if (i2400m->bus_release)
+ i2400m->bus_release(i2400m);
+ d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
+ return result;
+}
+EXPORT_SYMBOL_GPL(i2400m_pre_reset);
+
+
+/*
+ * Restore device state after a reset
+ *
+ * Do the work needed after a device reset to bring it up to the same
+ * state as it was before the reset.
+ *
+ * NOTE: this requires i2400m->init_mutex taken
+ */
+int i2400m_post_reset(struct i2400m *i2400m)
+{
+ int result = 0;
+ struct device *dev = i2400m_dev(i2400m);
+
+ d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+ d_printf(1, dev, "post-reset start\n");
+ if (i2400m->bus_setup) {
+ result = i2400m->bus_setup(i2400m);
+ if (result < 0) {
+ dev_err(dev, "bus-specific setup failed: %d\n",
+ result);
+ goto error_bus_setup;
+ }
+ }
+ mutex_lock(&i2400m->init_mutex);
+ if (i2400m->updown) {
+ result = __i2400m_dev_start(
+ i2400m, I2400M_BRI_SOFT | I2400M_BRI_MAC_REINIT);
+ if (result < 0)
+ goto error_dev_start;
+ }
+ mutex_unlock(&i2400m->init_mutex);
+ d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
+ return result;
+
+error_dev_start:
+ if (i2400m->bus_release)
+ i2400m->bus_release(i2400m);
+error_bus_setup:
+ /* even if the device was up, it could not be recovered, so we
+ * mark it as down. */
+ i2400m->updown = 0;
+ wmb(); /* see i2400m->updown's documentation */
+ mutex_unlock(&i2400m->init_mutex);
+ d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
+ return result;
+}
+EXPORT_SYMBOL_GPL(i2400m_post_reset);
+
+
+/*
* The device has rebooted; fix up the device and the driver
*
* Tear down the driver communication with the device, reload the
@@ -542,56 +656,69 @@ void i2400m_dev_stop(struct i2400m *i2400m)
* _stop()], don't do anything, let it fail and handle it.
*
* This function is ran always in a thread context
+ *
+ * This function gets passed, as payload to i2400m_work() a 'const
+ * char *' ptr with a "reason" why the reset happened (for messages).
*/
static
void __i2400m_dev_reset_handle(struct work_struct *ws)
{
int result;
struct i2400m_work *iw = container_of(ws, struct i2400m_work, ws);
+ const char *reason;
struct i2400m *i2400m = iw->i2400m;
struct device *dev = i2400m_dev(i2400m);
- enum wimax_st wimax_state;
struct i2400m_reset_ctx *ctx = i2400m->reset_ctx;
- d_fnstart(3, dev, "(ws %p i2400m %p)\n", ws, i2400m);
+ if (WARN_ON(iw->pl_size != sizeof(reason)))
+ reason = "SW BUG: reason n/a";
+ else
+ memcpy(&reason, iw->pl, sizeof(reason));
+
+ d_fnstart(3, dev, "(ws %p i2400m %p reason %s)\n", ws, i2400m, reason);
+
result = 0;
if (mutex_trylock(&i2400m->init_mutex) == 0) {
/* We are still in i2400m_dev_start() [let it fail] or
* i2400m_dev_stop() [we are shutting down anyway, so
* ignore it] or we are resetting somewhere else. */
- dev_err(dev, "device rebooted\n");
+ dev_err(dev, "device rebooted somewhere else?\n");
i2400m_msg_to_dev_cancel_wait(i2400m, -EL3RST);
complete(&i2400m->msg_completion);
goto out;
}
- wimax_state = wimax_state_get(&i2400m->wimax_dev);
- if (wimax_state < WIMAX_ST_UNINITIALIZED) {
- dev_info(dev, "device rebooted: it is down, ignoring\n");
- goto out_unlock; /* ifconfig up/down wasn't called */
+ if (i2400m->updown == 0) {
+ dev_info(dev, "%s: device is down, doing nothing\n", reason);
+ goto out_unlock;
}
- dev_err(dev, "device rebooted: reinitializing driver\n");
+ dev_err(dev, "%s: reinitializing driver\n", reason);
__i2400m_dev_stop(i2400m);
- i2400m->updown = 0;
result = __i2400m_dev_start(i2400m,
I2400M_BRI_SOFT | I2400M_BRI_MAC_REINIT);
if (result < 0) {
- dev_err(dev, "device reboot: cannot start the device: %d\n",
- result);
- result = i2400m->bus_reset(i2400m, I2400M_RT_BUS);
- if (result >= 0)
- result = -ENODEV;
- } else
- i2400m->updown = 1;
+ i2400m->updown = 0;
+ wmb(); /* see i2400m->updown's documentation */
+ dev_err(dev, "%s: cannot start the device: %d\n",
+ reason, result);
+ result = -EUCLEAN;
+ }
out_unlock:
if (i2400m->reset_ctx) {
ctx->result = result;
complete(&ctx->completion);
}
mutex_unlock(&i2400m->init_mutex);
+ if (result == -EUCLEAN) {
+ /* ops, need to clean up [w/ init_mutex not held] */
+ result = i2400m_reset(i2400m, I2400M_RT_BUS);
+ if (result >= 0)
+ result = -ENODEV;
+ }
out:
i2400m_put(i2400m);
kfree(iw);
- d_fnend(3, dev, "(ws %p i2400m %p) = void\n", ws, i2400m);
+ d_fnend(3, dev, "(ws %p i2400m %p reason %s) = void\n",
+ ws, i2400m, reason);
return;
}
@@ -608,16 +735,104 @@ out:
* reinitializing the driver to handle the reset, calling into the
* bus-specific functions ops as needed.
*/
-int i2400m_dev_reset_handle(struct i2400m *i2400m)
+int i2400m_dev_reset_handle(struct i2400m *i2400m, const char *reason)
{
i2400m->boot_mode = 1;
wmb(); /* Make sure i2400m_msg_to_dev() sees boot_mode */
return i2400m_schedule_work(i2400m, __i2400m_dev_reset_handle,
- GFP_ATOMIC);
+ GFP_ATOMIC, &reason, sizeof(reason));
}
EXPORT_SYMBOL_GPL(i2400m_dev_reset_handle);
+/*
+ * Alloc the command and ack buffers for boot mode
+ *
+ * Get the buffers needed to deal with boot mode messages. These
+ * buffers need to be allocated before the sdio recieve irq is setup.
+ */
+static
+int i2400m_bm_buf_alloc(struct i2400m *i2400m)
+{
+ int result;
+
+ result = -ENOMEM;
+ i2400m->bm_cmd_buf = kzalloc(I2400M_BM_CMD_BUF_SIZE, GFP_KERNEL);
+ if (i2400m->bm_cmd_buf == NULL)
+ goto error_bm_cmd_kzalloc;
+ i2400m->bm_ack_buf = kzalloc(I2400M_BM_ACK_BUF_SIZE, GFP_KERNEL);
+ if (i2400m->bm_ack_buf == NULL)
+ goto error_bm_ack_buf_kzalloc;
+ return 0;
+
+error_bm_ack_buf_kzalloc:
+ kfree(i2400m->bm_cmd_buf);
+error_bm_cmd_kzalloc:
+ return result;
+}
+
+
+/*
+ * Free boot mode command and ack buffers.
+ */
+static
+void i2400m_bm_buf_free(struct i2400m *i2400m)
+{
+ kfree(i2400m->bm_ack_buf);
+ kfree(i2400m->bm_cmd_buf);
+}
+
+
+/**
+ * i2400m_init - Initialize a 'struct i2400m' from all zeroes
+ *
+ * This is a bus-generic API call.
+ */
+void i2400m_init(struct i2400m *i2400m)
+{
+ wimax_dev_init(&i2400m->wimax_dev);
+
+ i2400m->boot_mode = 1;
+ i2400m->rx_reorder = 1;
+ init_waitqueue_head(&i2400m->state_wq);
+
+ spin_lock_init(&i2400m->tx_lock);
+ i2400m->tx_pl_min = UINT_MAX;
+ i2400m->tx_size_min = UINT_MAX;
+
+ spin_lock_init(&i2400m->rx_lock);
+ i2400m->rx_pl_min = UINT_MAX;
+ i2400m->rx_size_min = UINT_MAX;
+ INIT_LIST_HEAD(&i2400m->rx_reports);
+ INIT_WORK(&i2400m->rx_report_ws, i2400m_report_hook_work);
+
+ mutex_init(&i2400m->msg_mutex);
+ init_completion(&i2400m->msg_completion);
+
+ mutex_init(&i2400m->init_mutex);
+ /* wake_tx_ws is initialized in i2400m_tx_setup() */
+}
+EXPORT_SYMBOL_GPL(i2400m_init);
+
+
+int i2400m_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
+{
+ struct net_device *net_dev = i2400m->wimax_dev.net_dev;
+
+ /*
+ * Make sure we stop TXs and down the carrier before
+ * resetting; this is needed to avoid things like
+ * i2400m_wake_tx() scheduling stuff in parallel.
+ */
+ if (net_dev->reg_state == NETREG_REGISTERED) {
+ netif_tx_disable(net_dev);
+ netif_carrier_off(net_dev);
+ }
+ return i2400m->bus_reset(i2400m, rt);
+}
+EXPORT_SYMBOL_GPL(i2400m_reset);
+
+
/**
* i2400m_setup - bus-generic setup function for the i2400m device
*
@@ -625,13 +840,9 @@ EXPORT_SYMBOL_GPL(i2400m_dev_reset_handle);
*
* Returns: 0 if ok, < 0 errno code on error.
*
- * Initializes the bus-generic parts of the i2400m driver; the
- * bus-specific parts have been initialized, function pointers filled
- * out by the bus-specific probe function.
- *
- * As well, this registers the WiMAX and net device nodes. Once this
- * function returns, the device is operative and has to be ready to
- * receive and send network traffic and WiMAX control operations.
+ * Sets up basic device comunication infrastructure, boots the ROM to
+ * read the MAC address, registers with the WiMAX and network stacks
+ * and then brings up the device.
*/
int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
{
@@ -645,16 +856,21 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
snprintf(wimax_dev->name, sizeof(wimax_dev->name),
"i2400m-%s:%s", dev->bus->name, dev_name(dev));
- i2400m->bm_cmd_buf = kzalloc(I2400M_BM_CMD_BUF_SIZE, GFP_KERNEL);
- if (i2400m->bm_cmd_buf == NULL) {
- dev_err(dev, "cannot allocate USB command buffer\n");
- goto error_bm_cmd_kzalloc;
+ result = i2400m_bm_buf_alloc(i2400m);
+ if (result < 0) {
+ dev_err(dev, "cannot allocate bootmode scratch buffers\n");
+ goto error_bm_buf_alloc;
}
- i2400m->bm_ack_buf = kzalloc(I2400M_BM_ACK_BUF_SIZE, GFP_KERNEL);
- if (i2400m->bm_ack_buf == NULL) {
- dev_err(dev, "cannot allocate USB ack buffer\n");
- goto error_bm_ack_buf_kzalloc;
+
+ if (i2400m->bus_setup) {
+ result = i2400m->bus_setup(i2400m);
+ if (result < 0) {
+ dev_err(dev, "bus-specific setup failed: %d\n",
+ result);
+ goto error_bus_setup;
+ }
}
+
result = i2400m_bootrom_init(i2400m, bm_flags);
if (result < 0) {
dev_err(dev, "read mac addr: bootrom init "
@@ -666,6 +882,9 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
goto error_read_mac_addr;
random_ether_addr(i2400m->src_mac_addr);
+ i2400m->pm_notifier.notifier_call = i2400m_pm_notifier;
+ register_pm_notifier(&i2400m->pm_notifier);
+
result = register_netdev(net_dev); /* Okey dokey, bring it up */
if (result < 0) {
dev_err(dev, "cannot register i2400m network device: %d\n",
@@ -674,18 +893,13 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
}
netif_carrier_off(net_dev);
- result = i2400m_dev_start(i2400m, bm_flags);
- if (result < 0)
- goto error_dev_start;
-
i2400m->wimax_dev.op_msg_from_user = i2400m_op_msg_from_user;
i2400m->wimax_dev.op_rfkill_sw_toggle = i2400m_op_rfkill_sw_toggle;
i2400m->wimax_dev.op_reset = i2400m_op_reset;
+
result = wimax_dev_add(&i2400m->wimax_dev, net_dev);
if (result < 0)
goto error_wimax_dev_add;
- /* User space needs to do some init stuff */
- wimax_state_change(wimax_dev, WIMAX_ST_UNINITIALIZED);
/* Now setup all that requires a registered net and wimax device. */
result = sysfs_create_group(&net_dev->dev.kobj, &i2400m_dev_attr_group);
@@ -693,30 +907,37 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
dev_err(dev, "cannot setup i2400m's sysfs: %d\n", result);
goto error_sysfs_setup;
}
+
result = i2400m_debugfs_add(i2400m);
if (result < 0) {
dev_err(dev, "cannot setup i2400m's debugfs: %d\n", result);
goto error_debugfs_setup;
}
+
+ result = i2400m_dev_start(i2400m, bm_flags);
+ if (result < 0)
+ goto error_dev_start;
d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
return result;
+error_dev_start:
+ i2400m_debugfs_rm(i2400m);
error_debugfs_setup:
sysfs_remove_group(&i2400m->wimax_dev.net_dev->dev.kobj,
&i2400m_dev_attr_group);
error_sysfs_setup:
wimax_dev_rm(&i2400m->wimax_dev);
error_wimax_dev_add:
- i2400m_dev_stop(i2400m);
-error_dev_start:
unregister_netdev(net_dev);
error_register_netdev:
+ unregister_pm_notifier(&i2400m->pm_notifier);
error_read_mac_addr:
error_bootrom_init:
- kfree(i2400m->bm_ack_buf);
-error_bm_ack_buf_kzalloc:
- kfree(i2400m->bm_cmd_buf);
-error_bm_cmd_kzalloc:
+ if (i2400m->bus_release)
+ i2400m->bus_release(i2400m);
+error_bus_setup:
+ i2400m_bm_buf_free(i2400m);
+error_bm_buf_alloc:
d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
return result;
}
@@ -735,14 +956,17 @@ void i2400m_release(struct i2400m *i2400m)
d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
netif_stop_queue(i2400m->wimax_dev.net_dev);
+ i2400m_dev_stop(i2400m);
+
i2400m_debugfs_rm(i2400m);
sysfs_remove_group(&i2400m->wimax_dev.net_dev->dev.kobj,
&i2400m_dev_attr_group);
wimax_dev_rm(&i2400m->wimax_dev);
- i2400m_dev_stop(i2400m);
unregister_netdev(i2400m->wimax_dev.net_dev);
- kfree(i2400m->bm_ack_buf);
- kfree(i2400m->bm_cmd_buf);
+ unregister_pm_notifier(&i2400m->pm_notifier);
+ if (i2400m->bus_release)
+ i2400m->bus_release(i2400m);
+ i2400m_bm_buf_free(i2400m);
d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
}
EXPORT_SYMBOL_GPL(i2400m_release);
@@ -759,6 +983,7 @@ struct d_level D_LEVEL[] = {
D_SUBMODULE_DEFINE(netdev),
D_SUBMODULE_DEFINE(rfkill),
D_SUBMODULE_DEFINE(rx),
+ D_SUBMODULE_DEFINE(sysfs),
D_SUBMODULE_DEFINE(tx),
};
size_t D_LEVEL_SIZE = ARRAY_SIZE(D_LEVEL);
@@ -767,7 +992,9 @@ size_t D_LEVEL_SIZE = ARRAY_SIZE(D_LEVEL);
static
int __init i2400m_driver_init(void)
{
- return 0;
+ d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400m_debug_params,
+ "i2400m.debug");
+ return i2400m_barker_db_init(i2400m_barkers_params);
}
module_init(i2400m_driver_init);
@@ -776,6 +1003,7 @@ void __exit i2400m_driver_exit(void)
{
/* for scheds i2400m_dev_reset_handle() */
flush_scheduled_work();
+ i2400m_barker_db_exit();
return;
}
module_exit(i2400m_driver_exit);
diff --git a/drivers/net/wimax/i2400m/fw.c b/drivers/net/wimax/i2400m/fw.c
index e81750e..64cdfeb 100644
--- a/drivers/net/wimax/i2400m/fw.c
+++ b/drivers/net/wimax/i2400m/fw.c
@@ -40,11 +40,9 @@
*
* THE PROCEDURE
*
- * (this is decribed for USB, but for SDIO is similar)
- *
- * The 2400m works in two modes: boot-mode or normal mode. In boot
- * mode we can execute only a handful of commands targeted at
- * uploading the firmware and launching it.
+ * The 2400m and derived devices work in two modes: boot-mode or
+ * normal mode. In boot mode we can execute only a handful of commands
+ * targeted at uploading the firmware and launching it.
*
* The 2400m enters boot mode when it is first connected to the
* system, when it crashes and when you ask it to reboot. There are
@@ -52,18 +50,26 @@
* firmwares signed with a certain private key, non-signed takes any
* firmware. Normal hardware takes only signed firmware.
*
- * Upon entrance to boot mode, the device sends a few zero length
- * packets (ZLPs) on the notification endpoint, then a reboot barker
- * (4 le32 words with value I2400M_{S,N}BOOT_BARKER). We ack it by
- * sending the same barker on the bulk out endpoint. The device acks
- * with a reboot ack barker (4 le32 words with value 0xfeedbabe) and
- * then the device is fully rebooted. At this point we can upload the
- * firmware.
+ * On boot mode, in USB, we write to the device using the bulk out
+ * endpoint and read from it in the notification endpoint. In SDIO we
+ * talk to it via the write address and read from the read address.
+ *
+ * Upon entrance to boot mode, the device sends (preceeded with a few
+ * zero length packets (ZLPs) on the notification endpoint in USB) a
+ * reboot barker (4 le32 words with the same value). We ack it by
+ * sending the same barker to the device. The device acks with a
+ * reboot ack barker (4 le32 words with value I2400M_ACK_BARKER) and
+ * then is fully booted. At this point we can upload the firmware.
+ *
+ * Note that different iterations of the device and EEPROM
+ * configurations will send different [re]boot barkers; these are
+ * collected in i2400m_barker_db along with the firmware
+ * characteristics they require.
*
* This process is accomplished by the i2400m_bootrom_init()
* function. All the device interaction happens through the
* i2400m_bm_cmd() [boot mode command]. Special return values will
- * indicate if the device resets.
+ * indicate if the device did reset during the process.
*
* After this, we read the MAC address and then (if needed)
* reinitialize the device. We need to read it ahead of time because
@@ -72,11 +78,11 @@
*
* We can then upload the firmware file. The file is composed of a BCF
* header (basic data, keys and signatures) and a list of write
- * commands and payloads. We first upload the header
- * [i2400m_dnload_init()] and then pass the commands and payloads
- * verbatim to the i2400m_bm_cmd() function
- * [i2400m_dnload_bcf()]. Then we tell the device to jump to the new
- * firmware [i2400m_dnload_finalize()].
+ * commands and payloads. Optionally more BCF headers might follow the
+ * main payload. We first upload the header [i2400m_dnload_init()] and
+ * then pass the commands and payloads verbatim to the i2400m_bm_cmd()
+ * function [i2400m_dnload_bcf()]. Then we tell the device to jump to
+ * the new firmware [i2400m_dnload_finalize()].
*
* Once firmware is uploaded, we are good to go :)
*
@@ -99,18 +105,32 @@
* read an acknolwedgement from it (or an asynchronous notification)
* from it.
*
+ * FIRMWARE LOADING
+ *
+ * Note that in some cases, we can't just load a firmware file (for
+ * example, when resuming). For that, we might cache the firmware
+ * file. Thus, when doing the bootstrap, if there is a cache firmware
+ * file, it is used; if not, loading from disk is attempted.
+ *
* ROADMAP
*
+ * i2400m_barker_db_init Called by i2400m_driver_init()
+ * i2400m_barker_db_add
+ *
+ * i2400m_barker_db_exit Called by i2400m_driver_exit()
+ *
* i2400m_dev_bootstrap Called by __i2400m_dev_start()
* request_firmware
- * i2400m_fw_check
- * i2400m_fw_dnload
+ * i2400m_fw_bootstrap
+ * i2400m_fw_check
+ * i2400m_fw_hdr_check
+ * i2400m_fw_dnload
* release_firmware
*
* i2400m_fw_dnload
* i2400m_bootrom_init
* i2400m_bm_cmd
- * i2400m->bus_reset
+ * i2400m_reset
* i2400m_dnload_init
* i2400m_dnload_init_signed
* i2400m_dnload_init_nonsigned
@@ -125,9 +145,14 @@
* i2400m->bus_bm_cmd_send()
* i2400m->bus_bm_wait_for_ack
* __i2400m_bm_ack_verify
+ * i2400m_is_boot_barker
*
* i2400m_bm_cmd_prepare Used by bus-drivers to prep
* commands before sending
+ *
+ * i2400m_pm_notifier Called on Power Management events
+ * i2400m_fw_cache
+ * i2400m_fw_uncache
*/
#include <linux/firmware.h>
#include <linux/sched.h>
@@ -175,6 +200,240 @@ EXPORT_SYMBOL_GPL(i2400m_bm_cmd_prepare);
/*
+ * Database of known barkers.
+ *
+ * A barker is what the device sends indicating he is ready to be
+ * bootloaded. Different versions of the device will send different
+ * barkers. Depending on the barker, it might mean the device wants
+ * some kind of firmware or the other.
+ */
+static struct i2400m_barker_db {
+ __le32 data[4];
+} *i2400m_barker_db;
+static size_t i2400m_barker_db_used, i2400m_barker_db_size;
+
+
+static
+int i2400m_zrealloc_2x(void **ptr, size_t *_count, size_t el_size,
+ gfp_t gfp_flags)
+{
+ size_t old_count = *_count,
+ new_count = old_count ? 2 * old_count : 2,
+ old_size = el_size * old_count,
+ new_size = el_size * new_count;
+ void *nptr = krealloc(*ptr, new_size, gfp_flags);
+ if (nptr) {
+ /* zero the other half or the whole thing if old_count
+ * was zero */
+ if (old_size == 0)
+ memset(nptr, 0, new_size);
+ else
+ memset(nptr + old_size, 0, old_size);
+ *_count = new_count;
+ *ptr = nptr;
+ return 0;
+ } else
+ return -ENOMEM;
+}
+
+
+/*
+ * Add a barker to the database
+ *
+ * This cannot used outside of this module and only at at module_init
+ * time. This is to avoid the need to do locking.
+ */
+static
+int i2400m_barker_db_add(u32 barker_id)
+{
+ int result;
+
+ struct i2400m_barker_db *barker;
+ if (i2400m_barker_db_used >= i2400m_barker_db_size) {
+ result = i2400m_zrealloc_2x(
+ (void **) &i2400m_barker_db, &i2400m_barker_db_size,
+ sizeof(i2400m_barker_db[0]), GFP_KERNEL);
+ if (result < 0)
+ return result;
+ }
+ barker = i2400m_barker_db + i2400m_barker_db_used++;
+ barker->data[0] = le32_to_cpu(barker_id);
+ barker->data[1] = le32_to_cpu(barker_id);
+ barker->data[2] = le32_to_cpu(barker_id);
+ barker->data[3] = le32_to_cpu(barker_id);
+ return 0;
+}
+
+
+void i2400m_barker_db_exit(void)
+{
+ kfree(i2400m_barker_db);
+ i2400m_barker_db = NULL;
+ i2400m_barker_db_size = 0;
+ i2400m_barker_db_used = 0;
+}
+
+
+/*
+ * Helper function to add all the known stable barkers to the barker
+ * database.
+ */
+static
+int i2400m_barker_db_known_barkers(void)
+{
+ int result;
+
+ result = i2400m_barker_db_add(I2400M_NBOOT_BARKER);
+ if (result < 0)
+ goto error_add;
+ result = i2400m_barker_db_add(I2400M_SBOOT_BARKER);
+ if (result < 0)
+ goto error_add;
+ result = i2400m_barker_db_add(I2400M_SBOOT_BARKER_6050);
+ if (result < 0)
+ goto error_add;
+error_add:
+ return result;
+}
+
+
+/*
+ * Initialize the barker database
+ *
+ * This can only be used from the module_init function for this
+ * module; this is to avoid the need to do locking.
+ *
+ * @options: command line argument with extra barkers to
+ * recognize. This is a comma-separated list of 32-bit hex
+ * numbers. They are appended to the existing list. Setting 0
+ * cleans the existing list and starts a new one.
+ */
+int i2400m_barker_db_init(const char *_options)
+{
+ int result;
+ char *options = NULL, *options_orig, *token;
+
+ i2400m_barker_db = NULL;
+ i2400m_barker_db_size = 0;
+ i2400m_barker_db_used = 0;
+
+ result = i2400m_barker_db_known_barkers();
+ if (result < 0)
+ goto error_add;
+ /* parse command line options from i2400m.barkers */
+ if (_options != NULL) {
+ unsigned barker;
+
+ options_orig = kstrdup(_options, GFP_KERNEL);
+ if (options_orig == NULL)
+ goto error_parse;
+ options = options_orig;
+
+ while ((token = strsep(&options, ",")) != NULL) {
+ if (*token == '\0') /* eat joint commas */
+ continue;
+ if (sscanf(token, "%x", &barker) != 1
+ || barker > 0xffffffff) {
+ printk(KERN_ERR "%s: can't recognize "
+ "i2400m.barkers value '%s' as "
+ "a 32-bit number\n",
+ __func__, token);
+ result = -EINVAL;
+ goto error_parse;
+ }
+ if (barker == 0) {
+ /* clean list and start new */
+ i2400m_barker_db_exit();
+ continue;
+ }
+ result = i2400m_barker_db_add(barker);
+ if (result < 0)
+ goto error_add;
+ }
+ kfree(options_orig);
+ }
+ return 0;
+
+error_parse:
+error_add:
+ kfree(i2400m_barker_db);
+ return result;
+}
+
+
+/*
+ * Recognize a boot barker
+ *
+ * @buf: buffer where the boot barker.
+ * @buf_size: size of the buffer (has to be 16 bytes). It is passed
+ * here so the function can check it for the caller.
+ *
+ * Note that as a side effect, upon identifying the obtained boot
+ * barker, this function will set i2400m->barker to point to the right
+ * barker database entry. Subsequent calls to the function will result
+ * in verifying that the same type of boot barker is returned when the
+ * device [re]boots (as long as the same device instance is used).
+ *
+ * Return: 0 if @buf matches a known boot barker. -ENOENT if the
+ * buffer in @buf doesn't match any boot barker in the database or
+ * -EILSEQ if the buffer doesn't have the right size.
+ */
+int i2400m_is_boot_barker(struct i2400m *i2400m,
+ const void *buf, size_t buf_size)
+{
+ int result;
+ struct device *dev = i2400m_dev(i2400m);
+ struct i2400m_barker_db *barker;
+ int i;
+
+ result = -ENOENT;
+ if (buf_size != sizeof(i2400m_barker_db[i].data))
+ return result;
+
+ /* Short circuit if we have already discovered the barker
+ * associated with the device. */
+ if (i2400m->barker
+ && !memcmp(buf, i2400m->barker, sizeof(i2400m->barker->data))) {
+ unsigned index = (i2400m->barker - i2400m_barker_db)
+ / sizeof(*i2400m->barker);
+ d_printf(2, dev, "boot barker cache-confirmed #%u/%08x\n",
+ index, le32_to_cpu(i2400m->barker->data[0]));
+ return 0;
+ }
+
+ for (i = 0; i < i2400m_barker_db_used; i++) {
+ barker = &i2400m_barker_db[i];
+ BUILD_BUG_ON(sizeof(barker->data) != 16);
+ if (memcmp(buf, barker->data, sizeof(barker->data)))
+ continue;
+
+ if (i2400m->barker == NULL) {
+ i2400m->barker = barker;
+ d_printf(1, dev, "boot barker set to #%u/%08x\n",
+ i, le32_to_cpu(barker->data[0]));
+ if (barker->data[0] == le32_to_cpu(I2400M_NBOOT_BARKER))
+ i2400m->sboot = 0;
+ else
+ i2400m->sboot = 1;
+ } else if (i2400m->barker != barker) {
+ dev_err(dev, "HW inconsistency: device "
+ "reports a different boot barker "
+ "than set (from %08x to %08x)\n",
+ le32_to_cpu(i2400m->barker->data[0]),
+ le32_to_cpu(barker->data[0]));
+ result = -EIO;
+ } else
+ d_printf(2, dev, "boot barker confirmed #%u/%08x\n",
+ i, le32_to_cpu(barker->data[0]));
+ result = 0;
+ break;
+ }
+ return result;
+}
+EXPORT_SYMBOL_GPL(i2400m_is_boot_barker);
+
+
+/*
* Verify the ack data received
*
* Given a reply to a boot mode command, chew it and verify everything
@@ -204,20 +463,10 @@ ssize_t __i2400m_bm_ack_verify(struct i2400m *i2400m, int opcode,
opcode, ack_size, sizeof(*ack));
goto error_ack_short;
}
- if (ack_size == sizeof(i2400m_NBOOT_BARKER)
- && memcmp(ack, i2400m_NBOOT_BARKER, sizeof(*ack)) == 0) {
+ result = i2400m_is_boot_barker(i2400m, ack, ack_size);
+ if (result >= 0) {
result = -ERESTARTSYS;
- i2400m->sboot = 0;
- d_printf(6, dev, "boot-mode cmd %d: "
- "HW non-signed boot barker\n", opcode);
- goto error_reboot;
- }
- if (ack_size == sizeof(i2400m_SBOOT_BARKER)
- && memcmp(ack, i2400m_SBOOT_BARKER, sizeof(*ack)) == 0) {
- result = -ERESTARTSYS;
- i2400m->sboot = 1;
- d_printf(6, dev, "boot-mode cmd %d: HW signed reboot barker\n",
- opcode);
+ d_printf(6, dev, "boot-mode cmd %d: HW boot barker\n", opcode);
goto error_reboot;
}
if (ack_size == sizeof(i2400m_ACK_BARKER)
@@ -343,7 +592,6 @@ ssize_t i2400m_bm_cmd(struct i2400m *i2400m,
BUG_ON(i2400m->boot_mode == 0);
if (cmd != NULL) { /* send the command */
- memcpy(i2400m->bm_cmd_buf, cmd, cmd_size);
result = i2400m->bus_bm_cmd_send(i2400m, cmd, cmd_size, flags);
if (result < 0)
goto error_cmd_send;
@@ -432,8 +680,8 @@ static int i2400m_download_chunk(struct i2400m *i2400m, const void *chunk,
* Download a BCF file's sections to the device
*
* @i2400m: device descriptor
- * @bcf: pointer to firmware data (followed by the payloads). Assumed
- * verified and consistent.
+ * @bcf: pointer to firmware data (first header followed by the
+ * payloads). Assumed verified and consistent.
* @bcf_len: length (in bytes) of the @bcf buffer.
*
* Returns: < 0 errno code on error or the offset to the jump instruction.
@@ -472,14 +720,17 @@ ssize_t i2400m_dnload_bcf(struct i2400m *i2400m,
"downloading section #%zu (@%zu %zu B) to 0x%08x\n",
section, offset, sizeof(*bh) + data_size,
le32_to_cpu(bh->target_addr));
- if (i2400m_brh_get_opcode(bh) == I2400M_BRH_SIGNED_JUMP) {
- /* Secure boot needs to stop here */
- d_printf(5, dev, "signed jump found @%zu\n", offset);
+ /*
+ * We look for JUMP cmd from the bootmode header,
+ * either I2400M_BRH_SIGNED_JUMP for secure boot
+ * or I2400M_BRH_JUMP for unsecure boot, the last chunk
+ * should be the bootmode header with JUMP cmd.
+ */
+ if (i2400m_brh_get_opcode(bh) == I2400M_BRH_SIGNED_JUMP ||
+ i2400m_brh_get_opcode(bh) == I2400M_BRH_JUMP) {
+ d_printf(5, dev, "jump found @%zu\n", offset);
break;
}
- if (offset + section_size == bcf_len)
- /* Non-secure boot stops here */
- break;
if (offset + section_size > bcf_len) {
dev_err(dev, "fw %s: bad section #%zu, "
"end (@%zu) beyond EOF (@%zu)\n",
@@ -510,13 +761,30 @@ error_send:
/*
+ * Indicate if the device emitted a reboot barker that indicates
+ * "signed boot"
+ */
+static
+unsigned i2400m_boot_is_signed(struct i2400m *i2400m)
+{
+ return likely(i2400m->sboot);
+}
+
+
+/*
* Do the final steps of uploading firmware
*
+ * @bcf_hdr: BCF header we are actually using
+ * @bcf: pointer to the firmware image (which matches the first header
+ * that is followed by the actual payloads).
+ * @offset: [byte] offset into @bcf for the command we need to send.
+ *
* Depending on the boot mode (signed vs non-signed), different
* actions need to be taken.
*/
static
int i2400m_dnload_finalize(struct i2400m *i2400m,
+ const struct i2400m_bcf_hdr *bcf_hdr,
const struct i2400m_bcf_hdr *bcf, size_t offset)
{
int ret = 0;
@@ -530,10 +798,14 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
d_fnstart(3, dev, "offset %zu\n", offset);
cmd = (void *) bcf + offset;
- if (i2400m->sboot == 0) {
+ if (i2400m_boot_is_signed(i2400m) == 0) {
struct i2400m_bootrom_header jump_ack;
d_printf(1, dev, "unsecure boot, jumping to 0x%08x\n",
le32_to_cpu(cmd->target_addr));
+ cmd_buf = i2400m->bm_cmd_buf;
+ memcpy(&cmd_buf->cmd, cmd, sizeof(*cmd));
+ cmd = &cmd_buf->cmd;
+ /* now cmd points to the actual bootrom_header in cmd_buf */
i2400m_brh_set_opcode(cmd, I2400M_BRH_JUMP);
cmd->data_size = 0;
ret = i2400m_bm_cmd(i2400m, cmd, sizeof(*cmd),
@@ -544,12 +816,13 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
cmd_buf = i2400m->bm_cmd_buf;
memcpy(&cmd_buf->cmd, cmd, sizeof(*cmd));
signature_block_offset =
- sizeof(*bcf)
- + le32_to_cpu(bcf->key_size) * sizeof(u32)
- + le32_to_cpu(bcf->exponent_size) * sizeof(u32);
+ sizeof(*bcf_hdr)
+ + le32_to_cpu(bcf_hdr->key_size) * sizeof(u32)
+ + le32_to_cpu(bcf_hdr->exponent_size) * sizeof(u32);
signature_block_size =
- le32_to_cpu(bcf->modulus_size) * sizeof(u32);
- memcpy(cmd_buf->cmd_pl, (void *) bcf + signature_block_offset,
+ le32_to_cpu(bcf_hdr->modulus_size) * sizeof(u32);
+ memcpy(cmd_buf->cmd_pl,
+ (void *) bcf_hdr + signature_block_offset,
signature_block_size);
ret = i2400m_bm_cmd(i2400m, &cmd_buf->cmd,
sizeof(cmd_buf->cmd) + signature_block_size,
@@ -565,7 +838,7 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
*
* @i2400m: device descriptor
* @flags:
- * I2400M_BRI_SOFT: a reboot notification has been seen
+ * I2400M_BRI_SOFT: a reboot barker has been seen
* already, so don't wait for it.
*
* I2400M_BRI_NO_REBOOT: Don't send a reboot command, but wait
@@ -576,17 +849,15 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
*
* < 0 errno code on error, 0 if ok.
*
- * i2400m->sboot set to 0 for unsecure boot process, 1 for secure
- * boot process.
- *
* Description:
*
* Tries hard enough to put the device in boot-mode. There are two
* main phases to this:
*
* a. (1) send a reboot command and (2) get a reboot barker
- * b. (1) ack the reboot sending a reboot barker and (2) getting an
- * ack barker in return
+ *
+ * b. (1) echo/ack the reboot sending the reboot barker back and (2)
+ * getting an ack barker in return
*
* We want to skip (a) in some cases [soft]. The state machine is
* horrible, but it is basically: on each phase, send what has to be
@@ -594,6 +865,16 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
* have to backtrack and retry, so we keep a max tries counter for
* that.
*
+ * It sucks because we don't know ahead of time which is going to be
+ * the reboot barker (the device might send different ones depending
+ * on its EEPROM config) and once the device reboots and waits for the
+ * echo/ack reboot barker being sent back, it doesn't understand
+ * anything else. So we can be left at the point where we don't know
+ * what to send to it -- cold reset and bus reset seem to have little
+ * effect. So the function iterates (in this case) through all the
+ * known barkers and tries them all until an ACK is
+ * received. Otherwise, it gives up.
+ *
* If we get a timeout after sending a warm reset, we do it again.
*/
int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
@@ -602,10 +883,11 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
struct device *dev = i2400m_dev(i2400m);
struct i2400m_bootrom_header *cmd;
struct i2400m_bootrom_header ack;
- int count = I2400M_BOOT_RETRIES;
+ int count = i2400m->bus_bm_retries;
int ack_timeout_cnt = 1;
+ unsigned i;
- BUILD_BUG_ON(sizeof(*cmd) != sizeof(i2400m_NBOOT_BARKER));
+ BUILD_BUG_ON(sizeof(*cmd) != sizeof(i2400m_barker_db[0].data));
BUILD_BUG_ON(sizeof(ack) != sizeof(i2400m_ACK_BARKER));
d_fnstart(4, dev, "(i2400m %p flags 0x%08x)\n", i2400m, flags);
@@ -614,27 +896,59 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
if (flags & I2400M_BRI_SOFT)
goto do_reboot_ack;
do_reboot:
+ ack_timeout_cnt = 1;
if (--count < 0)
goto error_timeout;
d_printf(4, dev, "device reboot: reboot command [%d # left]\n",
count);
if ((flags & I2400M_BRI_NO_REBOOT) == 0)
- i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+ i2400m_reset(i2400m, I2400M_RT_WARM);
result = i2400m_bm_cmd(i2400m, NULL, 0, &ack, sizeof(ack),
I2400M_BM_CMD_RAW);
flags &= ~I2400M_BRI_NO_REBOOT;
switch (result) {
case -ERESTARTSYS:
+ /*
+ * at this point, i2400m_bm_cmd(), through
+ * __i2400m_bm_ack_process(), has updated
+ * i2400m->barker and we are good to go.
+ */
d_printf(4, dev, "device reboot: got reboot barker\n");
break;
case -EISCONN: /* we don't know how it got here...but we follow it */
d_printf(4, dev, "device reboot: got ack barker - whatever\n");
goto do_reboot;
- case -ETIMEDOUT: /* device has timed out, we might be in boot
- * mode already and expecting an ack, let's try
- * that */
- dev_info(dev, "warm reset timed out, trying an ack\n");
- goto do_reboot_ack;
+ case -ETIMEDOUT:
+ /*
+ * Device has timed out, we might be in boot mode
+ * already and expecting an ack; if we don't know what
+ * the barker is, we just send them all. Cold reset
+ * and bus reset don't work. Beats me.
+ */
+ if (i2400m->barker != NULL) {
+ dev_err(dev, "device boot: reboot barker timed out, "
+ "trying (set) %08x echo/ack\n",
+ le32_to_cpu(i2400m->barker->data[0]));
+ goto do_reboot_ack;
+ }
+ for (i = 0; i < i2400m_barker_db_used; i++) {
+ struct i2400m_barker_db *barker = &i2400m_barker_db[i];
+ memcpy(cmd, barker->data, sizeof(barker->data));
+ result = i2400m_bm_cmd(i2400m, cmd, sizeof(*cmd),
+ &ack, sizeof(ack),
+ I2400M_BM_CMD_RAW);
+ if (result == -EISCONN) {
+ dev_warn(dev, "device boot: got ack barker "
+ "after sending echo/ack barker "
+ "#%d/%08x; rebooting j.i.c.\n",
+ i, le32_to_cpu(barker->data[0]));
+ flags &= ~I2400M_BRI_NO_REBOOT;
+ goto do_reboot;
+ }
+ }
+ dev_err(dev, "device boot: tried all the echo/acks, could "
+ "not get device to respond; giving up");
+ result = -ESHUTDOWN;
case -EPROTO:
case -ESHUTDOWN: /* dev is gone */
case -EINTR: /* user cancelled */
@@ -642,6 +956,7 @@ do_reboot:
default:
dev_err(dev, "device reboot: error %d while waiting "
"for reboot barker - rebooting\n", result);
+ d_dump(1, dev, &ack, result);
goto do_reboot;
}
/* At this point we ack back with 4 REBOOT barkers and expect
@@ -650,12 +965,7 @@ do_reboot:
* notification and report it as -EISCONN. */
do_reboot_ack:
d_printf(4, dev, "device reboot ack: sending ack [%d # left]\n", count);
- if (i2400m->sboot == 0)
- memcpy(cmd, i2400m_NBOOT_BARKER,
- sizeof(i2400m_NBOOT_BARKER));
- else
- memcpy(cmd, i2400m_SBOOT_BARKER,
- sizeof(i2400m_SBOOT_BARKER));
+ memcpy(cmd, i2400m->barker->data, sizeof(i2400m->barker->data));
result = i2400m_bm_cmd(i2400m, cmd, sizeof(*cmd),
&ack, sizeof(ack), I2400M_BM_CMD_RAW);
switch (result) {
@@ -668,10 +978,8 @@ do_reboot_ack:
d_printf(4, dev, "reboot ack: got ack barker - good\n");
break;
case -ETIMEDOUT: /* no response, maybe it is the other type? */
- if (ack_timeout_cnt-- >= 0) {
- d_printf(4, dev, "reboot ack timedout: "
- "trying the other type?\n");
- i2400m->sboot = !i2400m->sboot;
+ if (ack_timeout_cnt-- < 0) {
+ d_printf(4, dev, "reboot ack timedout: retrying\n");
goto do_reboot_ack;
} else {
dev_err(dev, "reboot ack timedout too long: "
@@ -839,32 +1147,29 @@ int i2400m_dnload_init_signed(struct i2400m *i2400m,
* (signed or non-signed).
*/
static
-int i2400m_dnload_init(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf)
+int i2400m_dnload_init(struct i2400m *i2400m,
+ const struct i2400m_bcf_hdr *bcf_hdr)
{
int result;
struct device *dev = i2400m_dev(i2400m);
- u32 module_id = le32_to_cpu(bcf->module_id);
- if (i2400m->sboot == 0
- && (module_id & I2400M_BCF_MOD_ID_POKES) == 0) {
- /* non-signed boot process without pokes */
- result = i2400m_dnload_init_nonsigned(i2400m);
+ if (i2400m_boot_is_signed(i2400m)) {
+ d_printf(1, dev, "signed boot\n");
+ result = i2400m_dnload_init_signed(i2400m, bcf_hdr);
if (result == -ERESTARTSYS)
return result;
if (result < 0)
- dev_err(dev, "fw %s: non-signed download "
+ dev_err(dev, "firmware %s: signed boot download "
"initialization failed: %d\n",
i2400m->fw_name, result);
- } else if (i2400m->sboot == 0
- && (module_id & I2400M_BCF_MOD_ID_POKES)) {
- /* non-signed boot process with pokes, nothing to do */
- result = 0;
- } else { /* signed boot process */
- result = i2400m_dnload_init_signed(i2400m, bcf);
+ } else {
+ /* non-signed boot process without pokes */
+ d_printf(1, dev, "non-signed boot\n");
+ result = i2400m_dnload_init_nonsigned(i2400m);
if (result == -ERESTARTSYS)
return result;
if (result < 0)
- dev_err(dev, "fw %s: signed boot download "
+ dev_err(dev, "firmware %s: non-signed download "
"initialization failed: %d\n",
i2400m->fw_name, result);
}
@@ -873,74 +1178,201 @@ int i2400m_dnload_init(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf)
/*
- * Run quick consistency tests on the firmware file
+ * Run consistency tests on the firmware file and load up headers
*
* Check for the firmware being made for the i2400m device,
* etc...These checks are mostly informative, as the device will make
* them too; but the driver's response is more informative on what
* went wrong.
+ *
+ * This will also look at all the headers present on the firmware
+ * file, and update i2400m->fw_bcf_hdr to point to them.
*/
static
-int i2400m_fw_check(struct i2400m *i2400m,
- const struct i2400m_bcf_hdr *bcf,
- size_t bcf_size)
+int i2400m_fw_hdr_check(struct i2400m *i2400m,
+ const struct i2400m_bcf_hdr *bcf_hdr,
+ size_t index, size_t offset)
{
- int result;
struct device *dev = i2400m_dev(i2400m);
+
unsigned module_type, header_len, major_version, minor_version,
module_id, module_vendor, date, size;
- /* Check hard errors */
- result = -EINVAL;
- if (bcf_size < sizeof(*bcf)) { /* big enough header? */
- dev_err(dev, "firmware %s too short: "
- "%zu B vs %zu (at least) expected\n",
- i2400m->fw_name, bcf_size, sizeof(*bcf));
- goto error;
- }
+ module_type = bcf_hdr->module_type;
+ header_len = sizeof(u32) * le32_to_cpu(bcf_hdr->header_len);
+ major_version = (le32_to_cpu(bcf_hdr->header_version) & 0xffff0000)
+ >> 16;
+ minor_version = le32_to_cpu(bcf_hdr->header_version) & 0x0000ffff;
+ module_id = le32_to_cpu(bcf_hdr->module_id);
+ module_vendor = le32_to_cpu(bcf_hdr->module_vendor);
+ date = le32_to_cpu(bcf_hdr->date);
+ size = sizeof(u32) * le32_to_cpu(bcf_hdr->size);
- module_type = bcf->module_type;
- header_len = sizeof(u32) * le32_to_cpu(bcf->header_len);
- major_version = le32_to_cpu(bcf->header_version) & 0xffff0000 >> 16;
- minor_version = le32_to_cpu(bcf->header_version) & 0x0000ffff;
- module_id = le32_to_cpu(bcf->module_id);
- module_vendor = le32_to_cpu(bcf->module_vendor);
- date = le32_to_cpu(bcf->date);
- size = sizeof(u32) * le32_to_cpu(bcf->size);
-
- if (bcf_size != size) { /* annoyingly paranoid */
- dev_err(dev, "firmware %s: bad size, got "
- "%zu B vs %u expected\n",
- i2400m->fw_name, bcf_size, size);
- goto error;
- }
+ d_printf(1, dev, "firmware %s #%zd@%08zx: BCF header "
+ "type:vendor:id 0x%x:%x:%x v%u.%u (%u/%u B) built %08x\n",
+ i2400m->fw_name, index, offset,
+ module_type, module_vendor, module_id,
+ major_version, minor_version, header_len, size, date);
- d_printf(2, dev, "type 0x%x id 0x%x vendor 0x%x; header v%u.%u (%zu B) "
- "date %08x (%zu B)\n",
- module_type, module_id, module_vendor,
- major_version, minor_version, (size_t) header_len,
- date, (size_t) size);
+ /* Hard errors */
+ if (major_version != 1) {
+ dev_err(dev, "firmware %s #%zd@%08zx: major header version "
+ "v%u.%u not supported\n",
+ i2400m->fw_name, index, offset,
+ major_version, minor_version);
+ return -EBADF;
+ }
if (module_type != 6) { /* built for the right hardware? */
- dev_err(dev, "bad fw %s: unexpected module type 0x%x; "
- "aborting\n", i2400m->fw_name, module_type);
- goto error;
+ dev_err(dev, "firmware %s #%zd@%08zx: unexpected module "
+ "type 0x%x; aborting\n",
+ i2400m->fw_name, index, offset,
+ module_type);
+ return -EBADF;
+ }
+
+ if (module_vendor != 0x8086) {
+ dev_err(dev, "firmware %s #%zd@%08zx: unexpected module "
+ "vendor 0x%x; aborting\n",
+ i2400m->fw_name, index, offset, module_vendor);
+ return -EBADF;
}
- /* Check soft-er errors */
- result = 0;
- if (module_vendor != 0x8086)
- dev_err(dev, "bad fw %s? unexpected vendor 0x%04x\n",
- i2400m->fw_name, module_vendor);
if (date < 0x20080300)
- dev_err(dev, "bad fw %s? build date too old %08x\n",
- i2400m->fw_name, date);
-error:
+ dev_warn(dev, "firmware %s #%zd@%08zx: build date %08x "
+ "too old; unsupported\n",
+ i2400m->fw_name, index, offset, date);
+ return 0;
+}
+
+
+/*
+ * Run consistency tests on the firmware file and load up headers
+ *
+ * Check for the firmware being made for the i2400m device,
+ * etc...These checks are mostly informative, as the device will make
+ * them too; but the driver's response is more informative on what
+ * went wrong.
+ *
+ * This will also look at all the headers present on the firmware
+ * file, and update i2400m->fw_hdrs to point to them.
+ */
+static
+int i2400m_fw_check(struct i2400m *i2400m, const void *bcf, size_t bcf_size)
+{
+ int result;
+ struct device *dev = i2400m_dev(i2400m);
+ size_t headers = 0;
+ const struct i2400m_bcf_hdr *bcf_hdr;
+ const void *itr, *next, *top;
+ size_t slots = 0, used_slots = 0;
+
+ for (itr = bcf, top = itr + bcf_size;
+ itr < top;
+ headers++, itr = next) {
+ size_t leftover, offset, header_len, size;
+
+ leftover = top - itr;
+ offset = itr - (const void *) bcf;
+ if (leftover <= sizeof(*bcf_hdr)) {
+ dev_err(dev, "firmware %s: %zu B left at @%zx, "
+ "not enough for BCF header\n",
+ i2400m->fw_name, leftover, offset);
+ break;
+ }
+ bcf_hdr = itr;
+ /* Only the first header is supposed to be followed by
+ * payload */
+ header_len = sizeof(u32) * le32_to_cpu(bcf_hdr->header_len);
+ size = sizeof(u32) * le32_to_cpu(bcf_hdr->size);
+ if (headers == 0)
+ next = itr + size;
+ else
+ next = itr + header_len;
+
+ result = i2400m_fw_hdr_check(i2400m, bcf_hdr, headers, offset);
+ if (result < 0)
+ continue;
+ if (used_slots + 1 >= slots) {
+ /* +1 -> we need to account for the one we'll
+ * occupy and at least an extra one for
+ * always being NULL */
+ result = i2400m_zrealloc_2x(
+ (void **) &i2400m->fw_hdrs, &slots,
+ sizeof(i2400m->fw_hdrs[0]),
+ GFP_KERNEL);
+ if (result < 0)
+ goto error_zrealloc;
+ }
+ i2400m->fw_hdrs[used_slots] = bcf_hdr;
+ used_slots++;
+ }
+ if (headers == 0) {
+ dev_err(dev, "firmware %s: no usable headers found\n",
+ i2400m->fw_name);
+ result = -EBADF;
+ } else
+ result = 0;
+error_zrealloc:
return result;
}
/*
+ * Match a barker to a BCF header module ID
+ *
+ * The device sends a barker which tells the firmware loader which
+ * header in the BCF file has to be used. This does the matching.
+ */
+static
+unsigned i2400m_bcf_hdr_match(struct i2400m *i2400m,
+ const struct i2400m_bcf_hdr *bcf_hdr)
+{
+ u32 barker = le32_to_cpu(i2400m->barker->data[0])
+ & 0x7fffffff;
+ u32 module_id = le32_to_cpu(bcf_hdr->module_id)
+ & 0x7fffffff; /* high bit used for something else */
+
+ /* special case for 5x50 */
+ if (barker == I2400M_SBOOT_BARKER && module_id == 0)
+ return 1;
+ if (module_id == barker)
+ return 1;
+ return 0;
+}
+
+static
+const struct i2400m_bcf_hdr *i2400m_bcf_hdr_find(struct i2400m *i2400m)
+{
+ struct device *dev = i2400m_dev(i2400m);
+ const struct i2400m_bcf_hdr **bcf_itr, *bcf_hdr;
+ unsigned i = 0;
+ u32 barker = le32_to_cpu(i2400m->barker->data[0]);
+
+ d_printf(2, dev, "finding BCF header for barker %08x\n", barker);
+ if (barker == I2400M_NBOOT_BARKER) {
+ bcf_hdr = i2400m->fw_hdrs[0];
+ d_printf(1, dev, "using BCF header #%u/%08x for non-signed "
+ "barker\n", 0, le32_to_cpu(bcf_hdr->module_id));
+ return bcf_hdr;
+ }
+ for (bcf_itr = i2400m->fw_hdrs; *bcf_itr != NULL; bcf_itr++, i++) {
+ bcf_hdr = *bcf_itr;
+ if (i2400m_bcf_hdr_match(i2400m, bcf_hdr)) {
+ d_printf(1, dev, "hit on BCF hdr #%u/%08x\n",
+ i, le32_to_cpu(bcf_hdr->module_id));
+ return bcf_hdr;
+ } else
+ d_printf(1, dev, "miss on BCF hdr #%u/%08x\n",
+ i, le32_to_cpu(bcf_hdr->module_id));
+ }
+ dev_err(dev, "cannot find a matching BCF header for barker %08x\n",
+ barker);
+ return NULL;
+}
+
+
+/*
* Download the firmware to the device
*
* @i2400m: device descriptor
@@ -956,14 +1388,16 @@ error:
*/
static
int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
- size_t bcf_size, enum i2400m_bri flags)
+ size_t fw_size, enum i2400m_bri flags)
{
int ret = 0;
struct device *dev = i2400m_dev(i2400m);
int count = i2400m->bus_bm_retries;
+ const struct i2400m_bcf_hdr *bcf_hdr;
+ size_t bcf_size;
- d_fnstart(5, dev, "(i2400m %p bcf %p size %zu)\n",
- i2400m, bcf, bcf_size);
+ d_fnstart(5, dev, "(i2400m %p bcf %p fw size %zu)\n",
+ i2400m, bcf, fw_size);
i2400m->boot_mode = 1;
wmb(); /* Make sure other readers see it */
hw_reboot:
@@ -985,13 +1419,28 @@ hw_reboot:
* Initialize the download, push the bytes to the device and
* then jump to the new firmware. Note @ret is passed with the
* offset of the jump instruction to _dnload_finalize()
+ *
+ * Note we need to use the BCF header in the firmware image
+ * that matches the barker that the device sent when it
+ * rebooted, so it has to be passed along.
*/
- ret = i2400m_dnload_init(i2400m, bcf); /* Init device's dnload */
+ ret = -EBADF;
+ bcf_hdr = i2400m_bcf_hdr_find(i2400m);
+ if (bcf_hdr == NULL)
+ goto error_bcf_hdr_find;
+
+ ret = i2400m_dnload_init(i2400m, bcf_hdr);
if (ret == -ERESTARTSYS)
goto error_dev_rebooted;
if (ret < 0)
goto error_dnload_init;
+ /*
+ * bcf_size refers to one header size plus the fw sections size
+ * indicated by the header,ie. if there are other extended headers
+ * at the tail, they are not counted
+ */
+ bcf_size = sizeof(u32) * le32_to_cpu(bcf_hdr->size);
ret = i2400m_dnload_bcf(i2400m, bcf, bcf_size);
if (ret == -ERESTARTSYS)
goto error_dev_rebooted;
@@ -1001,7 +1450,7 @@ hw_reboot:
goto error_dnload_bcf;
}
- ret = i2400m_dnload_finalize(i2400m, bcf, ret);
+ ret = i2400m_dnload_finalize(i2400m, bcf_hdr, bcf, ret);
if (ret == -ERESTARTSYS)
goto error_dev_rebooted;
if (ret < 0) {
@@ -1018,10 +1467,11 @@ hw_reboot:
error_dnload_finalize:
error_dnload_bcf:
error_dnload_init:
+error_bcf_hdr_find:
error_bootrom_init:
error_too_many_reboots:
d_fnend(5, dev, "(i2400m %p bcf %p size %zu) = %d\n",
- i2400m, bcf, bcf_size, ret);
+ i2400m, bcf, fw_size, ret);
return ret;
error_dev_rebooted:
@@ -1031,6 +1481,61 @@ error_dev_rebooted:
goto hw_reboot;
}
+static
+int i2400m_fw_bootstrap(struct i2400m *i2400m, const struct firmware *fw,
+ enum i2400m_bri flags)
+{
+ int ret;
+ struct device *dev = i2400m_dev(i2400m);
+ const struct i2400m_bcf_hdr *bcf; /* Firmware data */
+
+ d_fnstart(5, dev, "(i2400m %p)\n", i2400m);
+ bcf = (void *) fw->data;
+ ret = i2400m_fw_check(i2400m, bcf, fw->size);
+ if (ret >= 0)
+ ret = i2400m_fw_dnload(i2400m, bcf, fw->size, flags);
+ if (ret < 0)
+ dev_err(dev, "%s: cannot use: %d, skipping\n",
+ i2400m->fw_name, ret);
+ kfree(i2400m->fw_hdrs);
+ i2400m->fw_hdrs = NULL;
+ d_fnend(5, dev, "(i2400m %p) = %d\n", i2400m, ret);
+ return ret;
+}
+
+
+/* Refcounted container for firmware data */
+struct i2400m_fw {
+ struct kref kref;
+ const struct firmware *fw;
+};
+
+
+static
+void i2400m_fw_destroy(struct kref *kref)
+{
+ struct i2400m_fw *i2400m_fw =
+ container_of(kref, struct i2400m_fw, kref);
+ release_firmware(i2400m_fw->fw);
+ kfree(i2400m_fw);
+}
+
+
+static
+struct i2400m_fw *i2400m_fw_get(struct i2400m_fw *i2400m_fw)
+{
+ if (i2400m_fw != NULL && i2400m_fw != (void *) ~0)
+ kref_get(&i2400m_fw->kref);
+ return i2400m_fw;
+}
+
+
+static
+void i2400m_fw_put(struct i2400m_fw *i2400m_fw)
+{
+ kref_put(&i2400m_fw->kref, i2400m_fw_destroy);
+}
+
/**
* i2400m_dev_bootstrap - Bring the device to a known state and upload firmware
@@ -1049,42 +1554,109 @@ error_dev_rebooted:
*/
int i2400m_dev_bootstrap(struct i2400m *i2400m, enum i2400m_bri flags)
{
- int ret = 0, itr = 0;
+ int ret, itr;
struct device *dev = i2400m_dev(i2400m);
- const struct firmware *fw;
+ struct i2400m_fw *i2400m_fw;
const struct i2400m_bcf_hdr *bcf; /* Firmware data */
+ const struct firmware *fw;
const char *fw_name;
d_fnstart(5, dev, "(i2400m %p)\n", i2400m);
+ ret = -ENODEV;
+ spin_lock(&i2400m->rx_lock);
+ i2400m_fw = i2400m_fw_get(i2400m->fw_cached);
+ spin_unlock(&i2400m->rx_lock);
+ if (i2400m_fw == (void *) ~0) {
+ dev_err(dev, "can't load firmware now!");
+ goto out;
+ } else if (i2400m_fw != NULL) {
+ dev_info(dev, "firmware %s: loading from cache\n",
+ i2400m->fw_name);
+ ret = i2400m_fw_bootstrap(i2400m, i2400m_fw->fw, flags);
+ i2400m_fw_put(i2400m_fw);
+ goto out;
+ }
+
/* Load firmware files to memory. */
- itr = 0;
- while(1) {
+ for (itr = 0, bcf = NULL, ret = -ENOENT; ; itr++) {
fw_name = i2400m->bus_fw_names[itr];
if (fw_name == NULL) {
dev_err(dev, "Could not find a usable firmware image\n");
- ret = -ENOENT;
- goto error_no_fw;
+ break;
}
+ d_printf(1, dev, "trying firmware %s (%d)\n", fw_name, itr);
ret = request_firmware(&fw, fw_name, dev);
- if (ret == 0)
- break; /* got it */
- if (ret < 0)
+ if (ret < 0) {
dev_err(dev, "fw %s: cannot load file: %d\n",
fw_name, ret);
- itr++;
+ continue;
+ }
+ i2400m->fw_name = fw_name;
+ ret = i2400m_fw_bootstrap(i2400m, fw, flags);
+ release_firmware(fw);
+ if (ret >= 0) /* firmware loaded succesfully */
+ break;
+ i2400m->fw_name = NULL;
}
-
- bcf = (void *) fw->data;
- i2400m->fw_name = fw_name;
- ret = i2400m_fw_check(i2400m, bcf, fw->size);
- if (ret < 0)
- goto error_fw_bad;
- ret = i2400m_fw_dnload(i2400m, bcf, fw->size, flags);
-error_fw_bad:
- release_firmware(fw);
-error_no_fw:
+out:
d_fnend(5, dev, "(i2400m %p) = %d\n", i2400m, ret);
return ret;
}
EXPORT_SYMBOL_GPL(i2400m_dev_bootstrap);
+
+
+void i2400m_fw_cache(struct i2400m *i2400m)
+{
+ int result;
+ struct i2400m_fw *i2400m_fw;
+ struct device *dev = i2400m_dev(i2400m);
+
+ /* if there is anything there, free it -- now, this'd be weird */
+ spin_lock(&i2400m->rx_lock);
+ i2400m_fw = i2400m->fw_cached;
+ spin_unlock(&i2400m->rx_lock);
+ if (i2400m_fw != NULL && i2400m_fw != (void *) ~0) {
+ i2400m_fw_put(i2400m_fw);
+ WARN(1, "%s:%u: still cached fw still present?\n",
+ __func__, __LINE__);
+ }
+
+ if (i2400m->fw_name == NULL) {
+ dev_err(dev, "firmware n/a: can't cache\n");
+ i2400m_fw = (void *) ~0;
+ goto out;
+ }
+
+ i2400m_fw = kzalloc(sizeof(*i2400m_fw), GFP_ATOMIC);
+ if (i2400m_fw == NULL)
+ goto out;
+ kref_init(&i2400m_fw->kref);
+ result = request_firmware(&i2400m_fw->fw, i2400m->fw_name, dev);
+ if (result < 0) {
+ dev_err(dev, "firmware %s: failed to cache: %d\n",
+ i2400m->fw_name, result);
+ kfree(i2400m_fw);
+ i2400m_fw = (void *) ~0;
+ } else
+ dev_info(dev, "firmware %s: cached\n", i2400m->fw_name);
+out:
+ spin_lock(&i2400m->rx_lock);
+ i2400m->fw_cached = i2400m_fw;
+ spin_unlock(&i2400m->rx_lock);
+}
+
+
+void i2400m_fw_uncache(struct i2400m *i2400m)
+{
+ struct i2400m_fw *i2400m_fw;
+
+ spin_lock(&i2400m->rx_lock);
+ i2400m_fw = i2400m->fw_cached;
+ i2400m->fw_cached = NULL;
+ spin_unlock(&i2400m->rx_lock);
+
+ if (i2400m_fw != NULL && i2400m_fw != (void *) ~0)
+ i2400m_fw_put(i2400m_fw);
+}
+
diff --git a/drivers/net/wimax/i2400m/i2400m-sdio.h b/drivers/net/wimax/i2400m/i2400m-sdio.h
index 9c4e318..b9c4bed 100644
--- a/drivers/net/wimax/i2400m/i2400m-sdio.h
+++ b/drivers/net/wimax/i2400m/i2400m-sdio.h
@@ -67,6 +67,7 @@
/* Host-Device interface for SDIO */
enum {
+ I2400M_SDIO_BOOT_RETRIES = 3,
I2400MS_BLK_SIZE = 256,
I2400MS_PL_SIZE_MAX = 0x3E00,
@@ -77,9 +78,11 @@ enum {
I2400MS_INTR_GET_SIZE_ADDR = 0x2C,
/* The number of ticks to wait for the device to signal that
* it is ready */
- I2400MS_INIT_SLEEP_INTERVAL = 10,
+ I2400MS_INIT_SLEEP_INTERVAL = 100,
/* How long to wait for the device to settle after reset */
I2400MS_SETTLE_TIME = 40,
+ /* The number of msec to wait for IOR after sending IOE */
+ IWMC3200_IOR_TIMEOUT = 10,
};
@@ -97,6 +100,14 @@ enum {
* @tx_workqueue: workqeueue used for data TX; we don't use the
* system's workqueue as that might cause deadlocks with code in
* the bus-generic driver.
+ *
+ * @debugfs_dentry: dentry for the SDIO specific debugfs files
+ *
+ * Note this value is set to NULL upon destruction; this is
+ * because some routinges use it to determine if we are inside the
+ * probe() path or some other path. When debugfs is disabled,
+ * creation sets the dentry to '(void*) -ENODEV', which is valid
+ * for the test.
*/
struct i2400ms {
struct i2400m i2400m; /* FIRST! See doc */
@@ -111,6 +122,9 @@ struct i2400ms {
wait_queue_head_t bm_wfa_wq;
int bm_wait_result;
size_t bm_ack_size;
+
+ /* Device is any of the iwmc3200 SKUs */
+ unsigned iwmc3200:1;
};
diff --git a/drivers/net/wimax/i2400m/i2400m-usb.h b/drivers/net/wimax/i2400m/i2400m-usb.h
index 6f76558..5cc0f27 100644
--- a/drivers/net/wimax/i2400m/i2400m-usb.h
+++ b/drivers/net/wimax/i2400m/i2400m-usb.h
@@ -88,6 +88,13 @@ struct edc {
u16 errorcount;
};
+struct i2400m_endpoint_cfg {
+ unsigned char bulk_out;
+ unsigned char notification;
+ unsigned char reset_cold;
+ unsigned char bulk_in;
+};
+
static inline void edc_init(struct edc *edc)
{
edc->timestart = jiffies;
@@ -137,15 +144,13 @@ static inline int edc_inc(struct edc *edc, u16 max_err, u16 timeframe)
/* Host-Device interface for USB */
enum {
+ I2400M_USB_BOOT_RETRIES = 3,
I2400MU_MAX_NOTIFICATION_LEN = 256,
I2400MU_BLK_SIZE = 16,
I2400MU_PL_SIZE_MAX = 0x3EFF,
- /* Endpoints */
- I2400MU_EP_BULK_OUT = 0,
- I2400MU_EP_NOTIFICATION,
- I2400MU_EP_RESET_COLD,
- I2400MU_EP_BULK_IN,
+ /* Device IDs */
+ USB_DEVICE_ID_I6050 = 0x0186,
};
@@ -215,6 +220,7 @@ struct i2400mu {
struct usb_device *usb_dev;
struct usb_interface *usb_iface;
struct edc urb_edc; /* Error density counter */
+ struct i2400m_endpoint_cfg endpoint_cfg;
struct urb *notif_urb;
struct task_struct *tx_kthread;
diff --git a/drivers/net/wimax/i2400m/i2400m.h b/drivers/net/wimax/i2400m/i2400m.h
index 60330f3..04df9bb 100644
--- a/drivers/net/wimax/i2400m/i2400m.h
+++ b/drivers/net/wimax/i2400m/i2400m.h
@@ -117,16 +117,30 @@
* well as i2400m->wimax_dev.net_dev and call i2400m_setup(). The
* i2400m driver will only register with the WiMAX and network stacks;
* the only access done to the device is to read the MAC address so we
- * can register a network device. This calls i2400m_dev_start() to
- * load firmware, setup communication with the device and configure it
- * for operation.
+ * can register a network device.
*
- * At this point, control and data communications are possible.
+ * The high-level call flow is:
+ *
+ * bus_probe()
+ * i2400m_setup()
+ * i2400m->bus_setup()
+ * boot rom initialization / read mac addr
+ * network / WiMAX stacks registration
+ * i2400m_dev_start()
+ * i2400m->bus_dev_start()
+ * i2400m_dev_initialize()
*
- * On disconnect/driver unload, the bus-specific disconnect function
- * calls i2400m_release() to undo i2400m_setup(). i2400m_dev_stop()
- * shuts the firmware down and releases resources uses to communicate
- * with the device.
+ * The reverse applies for a disconnect() call:
+ *
+ * bus_disconnect()
+ * i2400m_release()
+ * i2400m_dev_stop()
+ * i2400m_dev_shutdown()
+ * i2400m->bus_dev_stop()
+ * network / WiMAX stack unregistration
+ * i2400m->bus_release()
+ *
+ * At this point, control and data communications are possible.
*
* While the device is up, it might reset. The bus-specific driver has
* to catch that situation and call i2400m_dev_reset_handle() to deal
@@ -148,9 +162,6 @@
/* Misc constants */
enum {
- /* Firmware uploading */
- I2400M_BOOT_RETRIES = 3,
- I3200_BOOT_RETRIES = 3,
/* Size of the Boot Mode Command buffer */
I2400M_BM_CMD_BUF_SIZE = 16 * 1024,
I2400M_BM_ACK_BUF_SIZE = 256,
@@ -197,6 +208,7 @@ enum i2400m_reset_type {
struct i2400m_reset_ctx;
struct i2400m_roq;
+struct i2400m_barker_db;
/**
* struct i2400m - descriptor for an Intel 2400m
@@ -204,27 +216,50 @@ struct i2400m_roq;
* Members marked with [fill] must be filled out/initialized before
* calling i2400m_setup().
*
+ * Note the @bus_setup/@bus_release, @bus_dev_start/@bus_dev_release
+ * call pairs are very much doing almost the same, and depending on
+ * the underlying bus, some stuff has to be put in one or the
+ * other. The idea of setup/release is that they setup the minimal
+ * amount needed for loading firmware, where us dev_start/stop setup
+ * the rest needed to do full data/control traffic.
+ *
* @bus_tx_block_size: [fill] SDIO imposes a 256 block size, USB 16,
* so we have a tx_blk_size variable that the bus layer sets to
* tell the engine how much of that we need.
*
* @bus_pl_size_max: [fill] Maximum payload size.
*
- * @bus_dev_start: [fill] Function called by the bus-generic code
- * [i2400m_dev_start()] to setup the bus-specific communications
- * to the the device. See LIFE CYCLE above.
+ * @bus_setup: [optional fill] Function called by the bus-generic code
+ * [i2400m_setup()] to setup the basic bus-specific communications
+ * to the the device needed to load firmware. See LIFE CYCLE above.
*
* NOTE: Doesn't need to upload the firmware, as that is taken
* care of by the bus-generic code.
*
- * @bus_dev_stop: [fill] Function called by the bus-generic code
- * [i2400m_dev_stop()] to shutdown the bus-specific communications
- * to the the device. See LIFE CYCLE above.
+ * @bus_release: [optional fill] Function called by the bus-generic
+ * code [i2400m_release()] to shutdown the basic bus-specific
+ * communications to the the device needed to load firmware. See
+ * LIFE CYCLE above.
*
* This function does not need to reset the device, just tear down
* all the host resources created to handle communication with
* the device.
*
+ * @bus_dev_start: [optional fill] Function called by the bus-generic
+ * code [i2400m_dev_start()] to do things needed to start the
+ * device. See LIFE CYCLE above.
+ *
+ * NOTE: Doesn't need to upload the firmware, as that is taken
+ * care of by the bus-generic code.
+ *
+ * @bus_dev_stop: [optional fill] Function called by the bus-generic
+ * code [i2400m_dev_stop()] to do things needed for stopping the
+ * device. See LIFE CYCLE above.
+ *
+ * This function does not need to reset the device, just tear down
+ * all the host resources created to handle communication with
+ * the device.
+ *
* @bus_tx_kick: [fill] Function called by the bus-generic code to let
* the bus-specific code know that there is data available in the
* TX FIFO for transmission to the device.
@@ -246,6 +281,9 @@ struct i2400m_roq;
* process, so it cannot rely on common infrastructure being laid
* out.
*
+ * IMPORTANT: don't call reset on RT_BUS with i2400m->init_mutex
+ * held, as the .pre/.post reset handlers will deadlock.
+ *
* @bus_bm_retries: [fill] How many times shall a firmware upload /
* device initialization be retried? Different models of the same
* device might need different values, hence it is set by the
@@ -297,6 +335,27 @@ struct i2400m_roq;
* force this to be the first field so that we can get from
* netdev_priv() the right pointer.
*
+ * @updown: the device is up and ready for transmitting control and
+ * data packets. This implies @ready (communication infrastructure
+ * with the device is ready) and the device's firmware has been
+ * loaded and the device initialized.
+ *
+ * Write to it only inside a i2400m->init_mutex protected area
+ * followed with a wmb(); rmb() before accesing (unless locked
+ * inside i2400m->init_mutex). Read access can be loose like that
+ * [just using rmb()] because the paths that use this also do
+ * other error checks later on.
+ *
+ * @ready: Communication infrastructure with the device is ready, data
+ * frames can start to be passed around (this is lighter than
+ * using the WiMAX state for certain hot paths).
+ *
+ * Write to it only inside a i2400m->init_mutex protected area
+ * followed with a wmb(); rmb() before accesing (unless locked
+ * inside i2400m->init_mutex). Read access can be loose like that
+ * [just using rmb()] because the paths that use this also do
+ * other error checks later on.
+ *
* @rx_reorder: 1 if RX reordering is enabled; this can only be
* set at probe time.
*
@@ -362,6 +421,13 @@ struct i2400m_roq;
* delivered. Then the driver can release them to the host. See
* drivers/net/i2400m/rx.c for details.
*
+ * @rx_reports: reports received from the device that couldn't be
+ * processed because the driver wasn't still ready; when ready,
+ * they are pulled from here and chewed.
+ *
+ * @rx_reports_ws: Work struct used to kick a scan of the RX reports
+ * list and to process each.
+ *
* @src_mac_addr: MAC address used to make ethernet packets be coming
* from. This is generated at i2400m_setup() time and used during
* the life cycle of the instance. See i2400m_fake_eth_header().
@@ -422,6 +488,25 @@ struct i2400m_roq;
*
* @fw_version: version of the firmware interface, Major.minor,
* encoded in the high word and low word (major << 16 | minor).
+ *
+ * @fw_hdrs: NULL terminated array of pointers to the firmware
+ * headers. This is only available during firmware load time.
+ *
+ * @fw_cached: Used to cache firmware when the system goes to
+ * suspend/standby/hibernation (as on resume we can't read it). If
+ * NULL, no firmware was cached, read it. If ~0, you can't read
+ * any firmware files (the system still didn't come out of suspend
+ * and failed to cache one), so abort; otherwise, a valid cached
+ * firmware to be used. Access to this variable is protected by
+ * the spinlock i2400m->rx_lock.
+ *
+ * @barker: barker type that the device uses; this is initialized by
+ * i2400m_is_boot_barker() the first time it is called. Then it
+ * won't change during the life cycle of the device and everytime
+ * a boot barker is received, it is just verified for it being the
+ * same.
+ *
+ * @pm_notifier: used to register for PM events
*/
struct i2400m {
struct wimax_dev wimax_dev; /* FIRST! See doc */
@@ -429,7 +514,7 @@ struct i2400m {
unsigned updown:1; /* Network device is up or down */
unsigned boot_mode:1; /* is the device in boot mode? */
unsigned sboot:1; /* signed or unsigned fw boot */
- unsigned ready:1; /* all probing steps done */
+ unsigned ready:1; /* Device comm infrastructure ready */
unsigned rx_reorder:1; /* RX reorder is enabled */
u8 trace_msg_from_user; /* echo rx msgs to 'trace' pipe */
/* typed u8 so /sys/kernel/debug/u8 can tweak */
@@ -440,8 +525,10 @@ struct i2400m {
size_t bus_pl_size_max;
unsigned bus_bm_retries;
+ int (*bus_setup)(struct i2400m *);
int (*bus_dev_start)(struct i2400m *);
void (*bus_dev_stop)(struct i2400m *);
+ void (*bus_release)(struct i2400m *);
void (*bus_tx_kick)(struct i2400m *);
int (*bus_reset)(struct i2400m *, enum i2400m_reset_type);
ssize_t (*bus_bm_cmd_send)(struct i2400m *,
@@ -468,6 +555,8 @@ struct i2400m {
rx_num, rx_size_acc, rx_size_min, rx_size_max;
struct i2400m_roq *rx_roq; /* not under rx_lock! */
u8 src_mac_addr[ETH_HLEN];
+ struct list_head rx_reports; /* under rx_lock! */
+ struct work_struct rx_report_ws;
struct mutex msg_mutex; /* serialize command execution */
struct completion msg_completion;
@@ -487,37 +576,12 @@ struct i2400m {
struct dentry *debugfs_dentry;
const char *fw_name; /* name of the current firmware image */
unsigned long fw_version; /* version of the firmware interface */
-};
-
+ const struct i2400m_bcf_hdr **fw_hdrs;
+ struct i2400m_fw *fw_cached; /* protected by rx_lock */
+ struct i2400m_barker_db *barker;
-/*
- * Initialize a 'struct i2400m' from all zeroes
- *
- * This is a bus-generic API call.
- */
-static inline
-void i2400m_init(struct i2400m *i2400m)
-{
- wimax_dev_init(&i2400m->wimax_dev);
-
- i2400m->boot_mode = 1;
- i2400m->rx_reorder = 1;
- init_waitqueue_head(&i2400m->state_wq);
-
- spin_lock_init(&i2400m->tx_lock);
- i2400m->tx_pl_min = UINT_MAX;
- i2400m->tx_size_min = UINT_MAX;
-
- spin_lock_init(&i2400m->rx_lock);
- i2400m->rx_pl_min = UINT_MAX;
- i2400m->rx_size_min = UINT_MAX;
-
- mutex_init(&i2400m->msg_mutex);
- init_completion(&i2400m->msg_completion);
-
- mutex_init(&i2400m->init_mutex);
- /* wake_tx_ws is initialized in i2400m_tx_setup() */
-}
+ struct notifier_block pm_notifier;
+};
/*
@@ -577,6 +641,14 @@ extern void i2400m_bm_cmd_prepare(struct i2400m_bootrom_header *);
extern int i2400m_dev_bootstrap(struct i2400m *, enum i2400m_bri);
extern int i2400m_read_mac_addr(struct i2400m *);
extern int i2400m_bootrom_init(struct i2400m *, enum i2400m_bri);
+extern int i2400m_is_boot_barker(struct i2400m *, const void *, size_t);
+static inline
+int i2400m_is_d2h_barker(const void *buf)
+{
+ const __le32 *barker = buf;
+ return le32_to_cpu(*barker) == I2400M_D2H_MSG_BARKER;
+}
+extern void i2400m_unknown_barker(struct i2400m *, const void *, size_t);
/* Make/grok boot-rom header commands */
@@ -644,6 +716,8 @@ unsigned i2400m_brh_get_signature(const struct i2400m_bootrom_header *hdr)
/*
* Driver / device setup and internal functions
*/
+extern void i2400m_init(struct i2400m *);
+extern int i2400m_reset(struct i2400m *, enum i2400m_reset_type);
extern void i2400m_netdev_setup(struct net_device *net_dev);
extern int i2400m_sysfs_setup(struct device_driver *);
extern void i2400m_sysfs_release(struct device_driver *);
@@ -654,10 +728,14 @@ extern void i2400m_tx_release(struct i2400m *);
extern int i2400m_rx_setup(struct i2400m *);
extern void i2400m_rx_release(struct i2400m *);
+extern void i2400m_fw_cache(struct i2400m *);
+extern void i2400m_fw_uncache(struct i2400m *);
+
extern void i2400m_net_rx(struct i2400m *, struct sk_buff *, unsigned,
const void *, int);
extern void i2400m_net_erx(struct i2400m *, struct sk_buff *,
enum i2400m_cs);
+extern void i2400m_net_wake_stop(struct i2400m *);
enum i2400m_pt;
extern int i2400m_tx(struct i2400m *, const void *, size_t, enum i2400m_pt);
@@ -672,14 +750,12 @@ static inline int i2400m_debugfs_add(struct i2400m *i2400m)
static inline void i2400m_debugfs_rm(struct i2400m *i2400m) {}
#endif
-/* Called by _dev_start()/_dev_stop() to initialize the device itself */
+/* Initialize/shutdown the device */
extern int i2400m_dev_initialize(struct i2400m *);
extern void i2400m_dev_shutdown(struct i2400m *);
extern struct attribute_group i2400m_dev_attr_group;
-extern int i2400m_schedule_work(struct i2400m *,
- void (*)(struct work_struct *), gfp_t);
/* HDI message's payload description handling */
@@ -724,7 +800,9 @@ void i2400m_put(struct i2400m *i2400m)
dev_put(i2400m->wimax_dev.net_dev);
}
-extern int i2400m_dev_reset_handle(struct i2400m *);
+extern int i2400m_dev_reset_handle(struct i2400m *, const char *);
+extern int i2400m_pre_reset(struct i2400m *);
+extern int i2400m_post_reset(struct i2400m *);
/*
* _setup()/_release() are called by the probe/disconnect functions of
@@ -737,20 +815,6 @@ extern int i2400m_rx(struct i2400m *, struct sk_buff *);
extern struct i2400m_msg_hdr *i2400m_tx_msg_get(struct i2400m *, size_t *);
extern void i2400m_tx_msg_sent(struct i2400m *);
-static const __le32 i2400m_NBOOT_BARKER[4] = {
- cpu_to_le32(I2400M_NBOOT_BARKER),
- cpu_to_le32(I2400M_NBOOT_BARKER),
- cpu_to_le32(I2400M_NBOOT_BARKER),
- cpu_to_le32(I2400M_NBOOT_BARKER)
-};
-
-static const __le32 i2400m_SBOOT_BARKER[4] = {
- cpu_to_le32(I2400M_SBOOT_BARKER),
- cpu_to_le32(I2400M_SBOOT_BARKER),
- cpu_to_le32(I2400M_SBOOT_BARKER),
- cpu_to_le32(I2400M_SBOOT_BARKER)
-};
-
extern int i2400m_power_save_disabled;
/*
@@ -773,10 +837,12 @@ struct device *i2400m_dev(struct i2400m *i2400m)
struct i2400m_work {
struct work_struct ws;
struct i2400m *i2400m;
+ size_t pl_size;
u8 pl[0];
};
-extern int i2400m_queue_work(struct i2400m *,
- void (*)(struct work_struct *), gfp_t,
+
+extern int i2400m_schedule_work(struct i2400m *,
+ void (*)(struct work_struct *), gfp_t,
const void *, size_t);
extern int i2400m_msg_check_status(const struct i2400m_l3l4_hdr *,
@@ -789,6 +855,7 @@ extern void i2400m_msg_ack_hook(struct i2400m *,
const struct i2400m_l3l4_hdr *, size_t);
extern void i2400m_report_hook(struct i2400m *,
const struct i2400m_l3l4_hdr *, size_t);
+extern void i2400m_report_hook_work(struct work_struct *);
extern int i2400m_cmd_enter_powersave(struct i2400m *);
extern int i2400m_cmd_get_state(struct i2400m *);
extern int i2400m_cmd_exit_idle(struct i2400m *);
@@ -849,6 +916,12 @@ void __i2400m_msleep(unsigned ms)
#endif
}
+
+/* module initialization helpers */
+extern int i2400m_barker_db_init(const char *);
+extern void i2400m_barker_db_exit(void);
+
+
/* Module parameters */
extern int i2400m_idle_mode_disabled;
diff --git a/drivers/net/wimax/i2400m/netdev.c b/drivers/net/wimax/i2400m/netdev.c
index 796396c..599aa4e 100644
--- a/drivers/net/wimax/i2400m/netdev.c
+++ b/drivers/net/wimax/i2400m/netdev.c
@@ -74,6 +74,7 @@
*/
#include <linux/if_arp.h>
#include <linux/netdevice.h>
+#include <linux/ethtool.h>
#include "i2400m.h"
@@ -88,7 +89,10 @@ enum {
* The MTU is 1400 or less
*/
I2400M_MAX_MTU = 1400,
- I2400M_TX_TIMEOUT = HZ,
+ /* 20 secs? yep, this is the maximum timeout that the device
+ * might take to get out of IDLE / negotiate it with the base
+ * station. We add 1sec for good measure. */
+ I2400M_TX_TIMEOUT = 21 * HZ,
I2400M_TX_QLEN = 5,
};
@@ -101,22 +105,19 @@ int i2400m_open(struct net_device *net_dev)
struct device *dev = i2400m_dev(i2400m);
d_fnstart(3, dev, "(net_dev %p [i2400m %p])\n", net_dev, i2400m);
- if (i2400m->ready == 0) {
- dev_err(dev, "Device is still initializing\n");
- result = -EBUSY;
- } else
+ /* Make sure we wait until init is complete... */
+ mutex_lock(&i2400m->init_mutex);
+ if (i2400m->updown)
result = 0;
+ else
+ result = -EBUSY;
+ mutex_unlock(&i2400m->init_mutex);
d_fnend(3, dev, "(net_dev %p [i2400m %p]) = %d\n",
net_dev, i2400m, result);
return result;
}
-/*
- *
- * On kernel versions where cancel_work_sync() didn't return anything,
- * we rely on wake_tx_skb() being non-NULL.
- */
static
int i2400m_stop(struct net_device *net_dev)
{
@@ -124,21 +125,7 @@ int i2400m_stop(struct net_device *net_dev)
struct device *dev = i2400m_dev(i2400m);
d_fnstart(3, dev, "(net_dev %p [i2400m %p])\n", net_dev, i2400m);
- /* See i2400m_hard_start_xmit(), references are taken there
- * and here we release them if the work was still
- * pending. Note we can't differentiate work not pending vs
- * never scheduled, so the NULL check does that. */
- if (cancel_work_sync(&i2400m->wake_tx_ws) == 0
- && i2400m->wake_tx_skb != NULL) {
- unsigned long flags;
- struct sk_buff *wake_tx_skb;
- spin_lock_irqsave(&i2400m->tx_lock, flags);
- wake_tx_skb = i2400m->wake_tx_skb; /* compat help */
- i2400m->wake_tx_skb = NULL; /* compat help */
- spin_unlock_irqrestore(&i2400m->tx_lock, flags);
- i2400m_put(i2400m);
- kfree_skb(wake_tx_skb);
- }
+ i2400m_net_wake_stop(i2400m);
d_fnend(3, dev, "(net_dev %p [i2400m %p]) = 0\n", net_dev, i2400m);
return 0;
}
@@ -167,6 +154,7 @@ void i2400m_wake_tx_work(struct work_struct *ws)
{
int result;
struct i2400m *i2400m = container_of(ws, struct i2400m, wake_tx_ws);
+ struct net_device *net_dev = i2400m->wimax_dev.net_dev;
struct device *dev = i2400m_dev(i2400m);
struct sk_buff *skb = i2400m->wake_tx_skb;
unsigned long flags;
@@ -182,27 +170,36 @@ void i2400m_wake_tx_work(struct work_struct *ws)
dev_err(dev, "WAKE&TX: skb dissapeared!\n");
goto out_put;
}
+ /* If we have, somehow, lost the connection after this was
+ * queued, don't do anything; this might be the device got
+ * reset or just disconnected. */
+ if (unlikely(!netif_carrier_ok(net_dev)))
+ goto out_kfree;
result = i2400m_cmd_exit_idle(i2400m);
if (result == -EILSEQ)
result = 0;
if (result < 0) {
dev_err(dev, "WAKE&TX: device didn't get out of idle: "
- "%d\n", result);
- goto error;
+ "%d - resetting\n", result);
+ i2400m_reset(i2400m, I2400M_RT_BUS);
+ goto error;
}
result = wait_event_timeout(i2400m->state_wq,
- i2400m->state != I2400M_SS_IDLE, 5 * HZ);
+ i2400m->state != I2400M_SS_IDLE,
+ net_dev->watchdog_timeo - HZ/2);
if (result == 0)
result = -ETIMEDOUT;
if (result < 0) {
dev_err(dev, "WAKE&TX: error waiting for device to exit IDLE: "
- "%d\n", result);
+ "%d - resetting\n", result);
+ i2400m_reset(i2400m, I2400M_RT_BUS);
goto error;
}
msleep(20); /* device still needs some time or it drops it */
result = i2400m_tx(i2400m, skb->data, skb->len, I2400M_PT_DATA);
- netif_wake_queue(i2400m->wimax_dev.net_dev);
error:
+ netif_wake_queue(net_dev);
+out_kfree:
kfree_skb(skb); /* refcount transferred by _hard_start_xmit() */
out_put:
i2400m_put(i2400m);
@@ -229,6 +226,38 @@ void i2400m_tx_prep_header(struct sk_buff *skb)
}
+
+/*
+ * Cleanup resources acquired during i2400m_net_wake_tx()
+ *
+ * This is called by __i2400m_dev_stop and means we have to make sure
+ * the workqueue is flushed from any pending work.
+ */
+void i2400m_net_wake_stop(struct i2400m *i2400m)
+{
+ struct device *dev = i2400m_dev(i2400m);
+
+ d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+ /* See i2400m_hard_start_xmit(), references are taken there
+ * and here we release them if the work was still
+ * pending. Note we can't differentiate work not pending vs
+ * never scheduled, so the NULL check does that. */
+ if (cancel_work_sync(&i2400m->wake_tx_ws) == 0
+ && i2400m->wake_tx_skb != NULL) {
+ unsigned long flags;
+ struct sk_buff *wake_tx_skb;
+ spin_lock_irqsave(&i2400m->tx_lock, flags);
+ wake_tx_skb = i2400m->wake_tx_skb; /* compat help */
+ i2400m->wake_tx_skb = NULL; /* compat help */
+ spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+ i2400m_put(i2400m);
+ kfree_skb(wake_tx_skb);
+ }
+ d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
+ return;
+}
+
+
/*
* TX an skb to an idle device
*
@@ -342,6 +371,20 @@ netdev_tx_t i2400m_hard_start_xmit(struct sk_buff *skb,
int result;
d_fnstart(3, dev, "(skb %p net_dev %p)\n", skb, net_dev);
+ if (skb_header_cloned(skb)) {
+ /*
+ * Make tcpdump/wireshark happy -- if they are
+ * running, the skb is cloned and we will overwrite
+ * the mac fields in i2400m_tx_prep_header. Expand
+ * seems to fix this...
+ */
+ result = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (result) {
+ result = NETDEV_TX_BUSY;
+ goto error_expand;
+ }
+ }
+
if (i2400m->state == I2400M_SS_IDLE)
result = i2400m_net_wake_tx(i2400m, net_dev, skb);
else
@@ -352,10 +395,11 @@ netdev_tx_t i2400m_hard_start_xmit(struct sk_buff *skb,
net_dev->stats.tx_packets++;
net_dev->stats.tx_bytes += skb->len;
}
+ result = NETDEV_TX_OK;
+error_expand:
kfree_skb(skb);
-
- d_fnend(3, dev, "(skb %p net_dev %p)\n", skb, net_dev);
- return NETDEV_TX_OK;
+ d_fnend(3, dev, "(skb %p net_dev %p) = %d\n", skb, net_dev, result);
+ return result;
}
@@ -559,6 +603,22 @@ static const struct net_device_ops i2400m_netdev_ops = {
.ndo_change_mtu = i2400m_change_mtu,
};
+static void i2400m_get_drvinfo(struct net_device *net_dev,
+ struct ethtool_drvinfo *info)
+{
+ struct i2400m *i2400m = net_dev_to_i2400m(net_dev);
+
+ strncpy(info->driver, KBUILD_MODNAME, sizeof(info->driver) - 1);
+ strncpy(info->fw_version, i2400m->fw_name, sizeof(info->fw_version) - 1);
+ if (net_dev->dev.parent)
+ strncpy(info->bus_info, dev_name(net_dev->dev.parent),
+ sizeof(info->bus_info) - 1);
+}
+
+static const struct ethtool_ops i2400m_ethtool_ops = {
+ .get_drvinfo = i2400m_get_drvinfo,
+ .get_link = ethtool_op_get_link,
+};
/**
* i2400m_netdev_setup - Setup setup @net_dev's i2400m private data
@@ -580,6 +640,7 @@ void i2400m_netdev_setup(struct net_device *net_dev)
& ~IFF_MULTICAST);
net_dev->watchdog_timeo = I2400M_TX_TIMEOUT;
net_dev->netdev_ops = &i2400m_netdev_ops;
+ net_dev->ethtool_ops = &i2400m_ethtool_ops;
d_fnend(3, NULL, "(net_dev %p) = void\n", net_dev);
}
EXPORT_SYMBOL_GPL(i2400m_netdev_setup);
diff --git a/drivers/net/wimax/i2400m/rx.c b/drivers/net/wimax/i2400m/rx.c
index 07c32e6..e3d2a9d 100644
--- a/drivers/net/wimax/i2400m/rx.c
+++ b/drivers/net/wimax/i2400m/rx.c
@@ -158,30 +158,104 @@ struct i2400m_report_hook_args {
struct sk_buff *skb_rx;
const struct i2400m_l3l4_hdr *l3l4_hdr;
size_t size;
+ struct list_head list_node;
};
/*
* Execute i2400m_report_hook in a workqueue
*
- * Unpacks arguments from the deferred call, executes it and then
- * drops the references.
+ * Goes over the list of queued reports in i2400m->rx_reports and
+ * processes them.
*
- * Obvious NOTE: References are needed because we are a separate
- * thread; otherwise the buffer changes under us because it is
- * released by the original caller.
+ * NOTE: refcounts on i2400m are not needed because we flush the
+ * workqueue this runs on (i2400m->work_queue) before destroying
+ * i2400m.
*/
-static
void i2400m_report_hook_work(struct work_struct *ws)
{
- struct i2400m_work *iw =
- container_of(ws, struct i2400m_work, ws);
- struct i2400m_report_hook_args *args = (void *) iw->pl;
- if (iw->i2400m->ready)
- i2400m_report_hook(iw->i2400m, args->l3l4_hdr, args->size);
- kfree_skb(args->skb_rx);
- i2400m_put(iw->i2400m);
- kfree(iw);
+ struct i2400m *i2400m = container_of(ws, struct i2400m, rx_report_ws);
+ struct device *dev = i2400m_dev(i2400m);
+ struct i2400m_report_hook_args *args, *args_next;
+ LIST_HEAD(list);
+ unsigned long flags;
+
+ while (1) {
+ spin_lock_irqsave(&i2400m->rx_lock, flags);
+ list_splice_init(&i2400m->rx_reports, &list);
+ spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+ if (list_empty(&list))
+ break;
+ else
+ d_printf(1, dev, "processing queued reports\n");
+ list_for_each_entry_safe(args, args_next, &list, list_node) {
+ d_printf(2, dev, "processing queued report %p\n", args);
+ i2400m_report_hook(i2400m, args->l3l4_hdr, args->size);
+ kfree_skb(args->skb_rx);
+ list_del(&args->list_node);
+ kfree(args);
+ }
+ }
+}
+
+
+/*
+ * Flush the list of queued reports
+ */
+static
+void i2400m_report_hook_flush(struct i2400m *i2400m)
+{
+ struct device *dev = i2400m_dev(i2400m);
+ struct i2400m_report_hook_args *args, *args_next;
+ LIST_HEAD(list);
+ unsigned long flags;
+
+ d_printf(1, dev, "flushing queued reports\n");
+ spin_lock_irqsave(&i2400m->rx_lock, flags);
+ list_splice_init(&i2400m->rx_reports, &list);
+ spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+ list_for_each_entry_safe(args, args_next, &list, list_node) {
+ d_printf(2, dev, "flushing queued report %p\n", args);
+ kfree_skb(args->skb_rx);
+ list_del(&args->list_node);
+ kfree(args);
+ }
+}
+
+
+/*
+ * Queue a report for later processing
+ *
+ * @i2400m: device descriptor
+ * @skb_rx: skb that contains the payload (for reference counting)
+ * @l3l4_hdr: pointer to the control
+ * @size: size of the message
+ */
+static
+void i2400m_report_hook_queue(struct i2400m *i2400m, struct sk_buff *skb_rx,
+ const void *l3l4_hdr, size_t size)
+{
+ struct device *dev = i2400m_dev(i2400m);
+ unsigned long flags;
+ struct i2400m_report_hook_args *args;
+
+ args = kzalloc(sizeof(*args), GFP_NOIO);
+ if (args) {
+ args->skb_rx = skb_get(skb_rx);
+ args->l3l4_hdr = l3l4_hdr;
+ args->size = size;
+ spin_lock_irqsave(&i2400m->rx_lock, flags);
+ list_add_tail(&args->list_node, &i2400m->rx_reports);
+ spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+ d_printf(2, dev, "queued report %p\n", args);
+ rmb(); /* see i2400m->ready's documentation */
+ if (likely(i2400m->ready)) /* only send if up */
+ queue_work(i2400m->work_queue, &i2400m->rx_report_ws);
+ } else {
+ if (printk_ratelimit())
+ dev_err(dev, "%s:%u: Can't allocate %zu B\n",
+ __func__, __LINE__, sizeof(*args));
+ }
}
@@ -295,21 +369,29 @@ void i2400m_rx_ctl(struct i2400m *i2400m, struct sk_buff *skb_rx,
msg_type, size);
d_dump(2, dev, l3l4_hdr, size);
if (msg_type & I2400M_MT_REPORT_MASK) {
- /* These hooks have to be ran serialized; as well, the
- * handling might force the execution of commands, and
- * that might cause reentrancy issues with
- * bus-specific subdrivers and workqueues. So we run
- * it in a separate workqueue. */
- struct i2400m_report_hook_args args = {
- .skb_rx = skb_rx,
- .l3l4_hdr = l3l4_hdr,
- .size = size
- };
- if (unlikely(i2400m->ready == 0)) /* only send if up */
- return;
- skb_get(skb_rx);
- i2400m_queue_work(i2400m, i2400m_report_hook_work,
- GFP_KERNEL, &args, sizeof(args));
+ /*
+ * Process each report
+ *
+ * - has to be ran serialized as well
+ *
+ * - the handling might force the execution of
+ * commands. That might cause reentrancy issues with
+ * bus-specific subdrivers and workqueues, so the we
+ * run it in a separate workqueue.
+ *
+ * - when the driver is not yet ready to handle them,
+ * they are queued and at some point the queue is
+ * restarted [NOTE: we can't queue SKBs directly, as
+ * this might be a piece of a SKB, not the whole
+ * thing, and this is cheaper than cloning the
+ * SKB].
+ *
+ * Note we don't do refcounting for the device
+ * structure; this is because before destroying
+ * 'i2400m', we make sure to flush the
+ * i2400m->work_queue, so there are no issues.
+ */
+ i2400m_report_hook_queue(i2400m, skb_rx, l3l4_hdr, size);
if (unlikely(i2400m->trace_msg_from_user))
wimax_msg(&i2400m->wimax_dev, "echo",
l3l4_hdr, size, GFP_KERNEL);
@@ -363,8 +445,6 @@ void i2400m_rx_trace(struct i2400m *i2400m,
msg_type & I2400M_MT_REPORT_MASK ? "REPORT" : "CMD/SET/GET",
msg_type, size);
d_dump(2, dev, l3l4_hdr, size);
- if (unlikely(i2400m->ready == 0)) /* only send if up */
- return;
result = wimax_msg(wimax_dev, "trace", l3l4_hdr, size, GFP_KERNEL);
if (result < 0)
dev_err(dev, "error sending trace to userspace: %d\n",
@@ -748,7 +828,7 @@ void i2400m_roq_queue(struct i2400m *i2400m, struct i2400m_roq *roq,
dev_err(dev, "SW BUG? queue nsn %d (lbn %u ws %u)\n",
nsn, lbn, roq->ws);
i2400m_roq_log_dump(i2400m, roq);
- i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+ i2400m_reset(i2400m, I2400M_RT_WARM);
} else {
__i2400m_roq_queue(i2400m, roq, skb, lbn, nsn);
i2400m_roq_log_add(i2400m, roq, I2400M_RO_TYPE_PACKET,
@@ -814,7 +894,7 @@ void i2400m_roq_queue_update_ws(struct i2400m *i2400m, struct i2400m_roq *roq,
dev_err(dev, "SW BUG? queue_update_ws nsn %u (sn %u ws %u)\n",
nsn, sn, roq->ws);
i2400m_roq_log_dump(i2400m, roq);
- i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+ i2400m_reset(i2400m, I2400M_RT_WARM);
} else {
/* if the queue is empty, don't bother as we'd queue
* it and inmediately unqueue it -- just deliver it */
@@ -1194,6 +1274,28 @@ error_msg_hdr_check:
EXPORT_SYMBOL_GPL(i2400m_rx);
+void i2400m_unknown_barker(struct i2400m *i2400m,
+ const void *buf, size_t size)
+{
+ struct device *dev = i2400m_dev(i2400m);
+ char prefix[64];
+ const __le32 *barker = buf;
+ dev_err(dev, "RX: HW BUG? unknown barker %08x, "
+ "dropping %zu bytes\n", le32_to_cpu(*barker), size);
+ snprintf(prefix, sizeof(prefix), "%s %s: ",
+ dev_driver_string(dev), dev_name(dev));
+ if (size > 64) {
+ print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
+ 8, 4, buf, 64, 0);
+ printk(KERN_ERR "%s... (only first 64 bytes "
+ "dumped)\n", prefix);
+ } else
+ print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
+ 8, 4, buf, size, 0);
+}
+EXPORT_SYMBOL(i2400m_unknown_barker);
+
+
/*
* Initialize the RX queue and infrastructure
*
@@ -1261,4 +1363,6 @@ void i2400m_rx_release(struct i2400m *i2400m)
kfree(i2400m->rx_roq[0].log);
kfree(i2400m->rx_roq);
}
+ /* at this point, nothing can be received... */
+ i2400m_report_hook_flush(i2400m);
}
diff --git a/drivers/net/wimax/i2400m/sdio-fw.c b/drivers/net/wimax/i2400m/sdio-fw.c
index 7d6ec0f..8e02541 100644
--- a/drivers/net/wimax/i2400m/sdio-fw.c
+++ b/drivers/net/wimax/i2400m/sdio-fw.c
@@ -118,7 +118,8 @@ ssize_t i2400ms_bus_bm_cmd_send(struct i2400m *i2400m,
if (cmd_size > I2400M_BM_CMD_BUF_SIZE)
goto error_too_big;
- memcpy(i2400m->bm_cmd_buf, _cmd, cmd_size); /* Prep command */
+ if (_cmd != i2400m->bm_cmd_buf)
+ memmove(i2400m->bm_cmd_buf, _cmd, cmd_size);
cmd = i2400m->bm_cmd_buf;
if (cmd_size_a > cmd_size) /* Zero pad space */
memset(i2400m->bm_cmd_buf + cmd_size, 0, cmd_size_a - cmd_size);
@@ -177,10 +178,6 @@ ssize_t i2400ms_bus_bm_wait_for_ack(struct i2400m *i2400m,
d_fnstart(5, dev, "(i2400m %p ack %p size %zu)\n",
i2400m, ack, ack_size);
- spin_lock(&i2400m->rx_lock);
- i2400ms->bm_ack_size = -EINPROGRESS;
- spin_unlock(&i2400m->rx_lock);
-
result = wait_event_timeout(i2400ms->bm_wfa_wq,
i2400ms->bm_ack_size != -EINPROGRESS,
2 * HZ);
@@ -199,6 +196,10 @@ ssize_t i2400ms_bus_bm_wait_for_ack(struct i2400m *i2400m,
size = min(ack_size, i2400ms->bm_ack_size);
memcpy(ack, i2400m->bm_ack_buf, size);
}
+ /*
+ * Remember always to clear the bm_ack_size to -EINPROGRESS
+ * after the RX data is processed
+ */
i2400ms->bm_ack_size = -EINPROGRESS;
spin_unlock(&i2400m->rx_lock);
diff --git a/drivers/net/wimax/i2400m/sdio-rx.c b/drivers/net/wimax/i2400m/sdio-rx.c
index 321bead..8adf6c9 100644
--- a/drivers/net/wimax/i2400m/sdio-rx.c
+++ b/drivers/net/wimax/i2400m/sdio-rx.c
@@ -53,6 +53,7 @@
* i2400ms_irq()
* i2400ms_rx()
* __i2400ms_rx_get_size()
+ * i2400m_is_boot_barker()
* i2400m_rx()
*
* i2400ms_rx_setup()
@@ -138,6 +139,11 @@ void i2400ms_rx(struct i2400ms *i2400ms)
ret = rx_size;
goto error_get_size;
}
+ /*
+ * Hardware quirk: make sure to clear the INTR status register
+ * AFTER getting the data transfer size.
+ */
+ sdio_writeb(func, 1, I2400MS_INTR_CLEAR_ADDR, &ret);
ret = -ENOMEM;
skb = alloc_skb(rx_size, GFP_ATOMIC);
@@ -153,25 +159,34 @@ void i2400ms_rx(struct i2400ms *i2400ms)
}
rmb(); /* make sure we get boot_mode from dev_reset_handle */
- if (i2400m->boot_mode == 1) {
+ if (unlikely(i2400m->boot_mode == 1)) {
spin_lock(&i2400m->rx_lock);
i2400ms->bm_ack_size = rx_size;
spin_unlock(&i2400m->rx_lock);
memcpy(i2400m->bm_ack_buf, skb->data, rx_size);
wake_up(&i2400ms->bm_wfa_wq);
- dev_err(dev, "RX: SDIO boot mode message\n");
+ d_printf(5, dev, "RX: SDIO boot mode message\n");
kfree_skb(skb);
- } else if (unlikely(!memcmp(skb->data, i2400m_NBOOT_BARKER,
- sizeof(i2400m_NBOOT_BARKER))
- || !memcmp(skb->data, i2400m_SBOOT_BARKER,
- sizeof(i2400m_SBOOT_BARKER)))) {
- ret = i2400m_dev_reset_handle(i2400m);
+ goto out;
+ }
+ ret = -EIO;
+ if (unlikely(rx_size < sizeof(__le32))) {
+ dev_err(dev, "HW BUG? only %zu bytes received\n", rx_size);
+ goto error_bad_size;
+ }
+ if (likely(i2400m_is_d2h_barker(skb->data))) {
+ skb_put(skb, rx_size);
+ i2400m_rx(i2400m, skb);
+ } else if (unlikely(i2400m_is_boot_barker(i2400m,
+ skb->data, rx_size))) {
+ ret = i2400m_dev_reset_handle(i2400m, "device rebooted");
dev_err(dev, "RX: SDIO reboot barker\n");
kfree_skb(skb);
} else {
- skb_put(skb, rx_size);
- i2400m_rx(i2400m, skb);
+ i2400m_unknown_barker(i2400m, skb->data, rx_size);
+ kfree_skb(skb);
}
+out:
d_fnend(7, dev, "(i2400ms %p) = void\n", i2400ms);
return;
@@ -179,6 +194,7 @@ error_memcpy_fromio:
kfree_skb(skb);
error_alloc_skb:
error_get_size:
+error_bad_size:
d_fnend(7, dev, "(i2400ms %p) = %d\n", i2400ms, ret);
return;
}
@@ -209,7 +225,6 @@ void i2400ms_irq(struct sdio_func *func)
dev_err(dev, "RX: BUG? got IRQ but no interrupt ready?\n");
goto error_no_irq;
}
- sdio_writeb(func, 1, I2400MS_INTR_CLEAR_ADDR, &ret);
i2400ms_rx(i2400ms);
error_no_irq:
d_fnend(6, dev, "(i2400ms %p) = void\n", i2400ms);
@@ -234,6 +249,13 @@ int i2400ms_rx_setup(struct i2400ms *i2400ms)
init_waitqueue_head(&i2400ms->bm_wfa_wq);
spin_lock(&i2400m->rx_lock);
i2400ms->bm_wait_result = -EINPROGRESS;
+ /*
+ * Before we are about to enable the RX interrupt, make sure
+ * bm_ack_size is cleared to -EINPROGRESS which indicates
+ * no RX interrupt happened yet or the previous interrupt
+ * has been handled, we are ready to take the new interrupt
+ */
+ i2400ms->bm_ack_size = -EINPROGRESS;
spin_unlock(&i2400m->rx_lock);
sdio_claim_host(func);
diff --git a/drivers/net/wimax/i2400m/sdio-tx.c b/drivers/net/wimax/i2400m/sdio-tx.c
index 5105a5e..de66d06 100644
--- a/drivers/net/wimax/i2400m/sdio-tx.c
+++ b/drivers/net/wimax/i2400m/sdio-tx.c
@@ -149,5 +149,8 @@ int i2400ms_tx_setup(struct i2400ms *i2400ms)
void i2400ms_tx_release(struct i2400ms *i2400ms)
{
- destroy_workqueue(i2400ms->tx_workqueue);
+ if (i2400ms->tx_workqueue) {
+ destroy_workqueue(i2400ms->tx_workqueue);
+ i2400ms->tx_workqueue = NULL;
+ }
}
diff --git a/drivers/net/wimax/i2400m/sdio.c b/drivers/net/wimax/i2400m/sdio.c
index 2981e21..76a50ac 100644
--- a/drivers/net/wimax/i2400m/sdio.c
+++ b/drivers/net/wimax/i2400m/sdio.c
@@ -43,18 +43,9 @@
* i2400m_release()
* free_netdev(net_dev)
*
- * i2400ms_bus_reset() Called by i2400m->bus_reset
+ * i2400ms_bus_reset() Called by i2400m_reset
* __i2400ms_reset()
* __i2400ms_send_barker()
- *
- * i2400ms_bus_dev_start() Called by i2400m_dev_start() [who is
- * i2400ms_tx_setup() called by i2400m_setup()]
- * i2400ms_rx_setup()
- *
- * i2400ms_bus_dev_stop() Called by i2400m_dev_stop() [who is
- * i2400ms_rx_release() is called by i2400m_release()]
- * i2400ms_tx_release()
- *
*/
#include <linux/debugfs.h>
@@ -71,6 +62,14 @@
static int ioe_timeout = 2;
module_param(ioe_timeout, int, 0);
+static char i2400ms_debug_params[128];
+module_param_string(debug, i2400ms_debug_params, sizeof(i2400ms_debug_params),
+ 0644);
+MODULE_PARM_DESC(debug,
+ "String of space-separated NAME:VALUE pairs, where NAMEs "
+ "are the different debug submodules and VALUE are the "
+ "initial debug value to set.");
+
/* Our firmware file name list */
static const char *i2400ms_bus_fw_names[] = {
#define I2400MS_FW_FILE_NAME "i2400m-fw-sdio-1.3.sbcf"
@@ -95,17 +94,24 @@ static const struct i2400m_poke_table i2400ms_pokes[] = {
* when we ask it to explicitly doing). Tries until a timeout is
* reached.
*
+ * The @maxtries argument indicates how many times (at most) it should
+ * be tried to enable the function. 0 means forever. This acts along
+ * with the timeout (ie: it'll stop trying as soon as the maximum
+ * number of tries is reached _or_ as soon as the timeout is reached).
+ *
* The reverse of this is...sdio_disable_function()
*
* Returns: 0 if the SDIO function was enabled, < 0 errno code on
* error (-ENODEV when it was unable to enable the function).
*/
static
-int i2400ms_enable_function(struct sdio_func *func)
+int i2400ms_enable_function(struct i2400ms *i2400ms, unsigned maxtries)
{
+ struct sdio_func *func = i2400ms->func;
u64 timeout;
int err;
struct device *dev = &func->dev;
+ unsigned tries = 0;
d_fnstart(3, dev, "(func %p)\n", func);
/* Setup timeout (FIXME: This needs to read the CIS table to
@@ -115,6 +121,14 @@ int i2400ms_enable_function(struct sdio_func *func)
err = -ENODEV;
while (err != 0 && time_before64(get_jiffies_64(), timeout)) {
sdio_claim_host(func);
+ /*
+ * There is a sillicon bug on the IWMC3200, where the
+ * IOE timeout will cause problems on Moorestown
+ * platforms (system hang). We explicitly overwrite
+ * func->enable_timeout here to work around the issue.
+ */
+ if (i2400ms->iwmc3200)
+ func->enable_timeout = IWMC3200_IOR_TIMEOUT;
err = sdio_enable_func(func);
if (0 == err) {
sdio_release_host(func);
@@ -122,8 +136,11 @@ int i2400ms_enable_function(struct sdio_func *func)
goto function_enabled;
}
d_printf(2, dev, "SDIO function failed to enable: %d\n", err);
- sdio_disable_func(func);
sdio_release_host(func);
+ if (maxtries > 0 && ++tries >= maxtries) {
+ err = -ETIME;
+ break;
+ }
msleep(I2400MS_INIT_SLEEP_INTERVAL);
}
/* If timed out, device is not there yet -- get -ENODEV so
@@ -140,46 +157,99 @@ function_enabled:
/*
- * Setup driver resources needed to communicate with the device
+ * Setup minimal device communication infrastructure needed to at
+ * least be able to update the firmware.
*
- * The fw needs some time to settle, and it was just uploaded,
- * so give it a break first. I'd prefer to just wait for the device to
- * send something, but seems the poking we do to enable SDIO stuff
- * interferes with it, so just give it a break before starting...
+ * Note the ugly trick: if we are in the probe path
+ * (i2400ms->debugfs_dentry == NULL), we only retry function
+ * enablement one, to avoid racing with the iwmc3200 top controller.
*/
static
-int i2400ms_bus_dev_start(struct i2400m *i2400m)
+int i2400ms_bus_setup(struct i2400m *i2400m)
{
int result;
- struct i2400ms *i2400ms = container_of(i2400m, struct i2400ms, i2400m);
+ struct i2400ms *i2400ms =
+ container_of(i2400m, struct i2400ms, i2400m);
+ struct device *dev = i2400m_dev(i2400m);
struct sdio_func *func = i2400ms->func;
- struct device *dev = &func->dev;
+ int retries;
+
+ sdio_claim_host(func);
+ result = sdio_set_block_size(func, I2400MS_BLK_SIZE);
+ sdio_release_host(func);
+ if (result < 0) {
+ dev_err(dev, "Failed to set block size: %d\n", result);
+ goto error_set_blk_size;
+ }
+
+ if (i2400ms->iwmc3200 && i2400ms->debugfs_dentry == NULL)
+ retries = 1;
+ else
+ retries = 0;
+ result = i2400ms_enable_function(i2400ms, retries);
+ if (result < 0) {
+ dev_err(dev, "Cannot enable SDIO function: %d\n", result);
+ goto error_func_enable;
+ }
- d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
- msleep(200);
result = i2400ms_tx_setup(i2400ms);
if (result < 0)
goto error_tx_setup;
- d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
- return result;
+ result = i2400ms_rx_setup(i2400ms);
+ if (result < 0)
+ goto error_rx_setup;
+ return 0;
-error_tx_setup:
+error_rx_setup:
i2400ms_tx_release(i2400ms);
- d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
+error_tx_setup:
+ sdio_claim_host(func);
+ sdio_disable_func(func);
+ sdio_release_host(func);
+error_func_enable:
+error_set_blk_size:
return result;
}
+/*
+ * Tear down minimal device communication infrastructure needed to at
+ * least be able to update the firmware.
+ */
+static
+void i2400ms_bus_release(struct i2400m *i2400m)
+{
+ struct i2400ms *i2400ms =
+ container_of(i2400m, struct i2400ms, i2400m);
+ struct sdio_func *func = i2400ms->func;
+
+ i2400ms_rx_release(i2400ms);
+ i2400ms_tx_release(i2400ms);
+ sdio_claim_host(func);
+ sdio_disable_func(func);
+ sdio_release_host(func);
+}
+
+
+/*
+ * Setup driver resources needed to communicate with the device
+ *
+ * The fw needs some time to settle, and it was just uploaded,
+ * so give it a break first. I'd prefer to just wait for the device to
+ * send something, but seems the poking we do to enable SDIO stuff
+ * interferes with it, so just give it a break before starting...
+ */
static
-void i2400ms_bus_dev_stop(struct i2400m *i2400m)
+int i2400ms_bus_dev_start(struct i2400m *i2400m)
{
struct i2400ms *i2400ms = container_of(i2400m, struct i2400ms, i2400m);
struct sdio_func *func = i2400ms->func;
struct device *dev = &func->dev;
d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
- i2400ms_tx_release(i2400ms);
- d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
+ msleep(200);
+ d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, 0);
+ return 0;
}
@@ -233,18 +303,17 @@ error_kzalloc:
* Warm reset:
*
* The device will be fully reset internally, but won't be
- * disconnected from the USB bus (so no reenumeration will
+ * disconnected from the bus (so no reenumeration will
* happen). Firmware upload will be neccessary.
*
- * The device will send a reboot barker in the notification endpoint
- * that will trigger the driver to reinitialize the state
- * automatically from notif.c:i2400m_notification_grok() into
- * i2400m_dev_bootstrap_delayed().
+ * The device will send a reboot barker that will trigger the driver
+ * to reinitialize the state via __i2400m_dev_reset_handle.
*
- * Cold and bus (USB) reset:
+ *
+ * Cold and bus reset:
*
* The device will be fully reset internally, disconnected from the
- * USB bus an a reenumeration will happen. Firmware upload will be
+ * bus an a reenumeration will happen. Firmware upload will be
* neccessary. Thus, we don't do any locking or struct
* reinitialization, as we are going to be fully disconnected and
* reenumerated.
@@ -283,25 +352,13 @@ int i2400ms_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
sizeof(i2400m_COLD_BOOT_BARKER));
else if (rt == I2400M_RT_BUS) {
do_bus_reset:
- /* call netif_tx_disable() before sending IOE disable,
- * so that all the tx from network layer are stopped
- * while IOE is being reset. Make sure it is called
- * only after register_netdev() was issued.
- */
- if (i2400m->wimax_dev.net_dev->reg_state == NETREG_REGISTERED)
- netif_tx_disable(i2400m->wimax_dev.net_dev);
- i2400ms_rx_release(i2400ms);
- sdio_claim_host(i2400ms->func);
- sdio_disable_func(i2400ms->func);
- sdio_release_host(i2400ms->func);
+ i2400ms_bus_release(i2400m);
/* Wait for the device to settle */
msleep(40);
- result = i2400ms_enable_function(i2400ms->func);
- if (result >= 0)
- i2400ms_rx_setup(i2400ms);
+ result = i2400ms_bus_setup(i2400m);
} else
BUG();
if (result < 0 && rt != I2400M_RT_BUS) {
@@ -350,7 +407,7 @@ int i2400ms_debugfs_add(struct i2400ms *i2400ms)
int result;
struct dentry *dentry = i2400ms->i2400m.wimax_dev.debugfs_dentry;
- dentry = debugfs_create_dir("i2400m-usb", dentry);
+ dentry = debugfs_create_dir("i2400m-sdio", dentry);
result = PTR_ERR(dentry);
if (IS_ERR(dentry)) {
if (result == -ENODEV)
@@ -367,6 +424,7 @@ int i2400ms_debugfs_add(struct i2400ms *i2400ms)
error:
debugfs_remove_recursive(i2400ms->debugfs_dentry);
+ i2400ms->debugfs_dentry = NULL;
return result;
}
@@ -425,37 +483,30 @@ int i2400ms_probe(struct sdio_func *func,
i2400m->bus_tx_block_size = I2400MS_BLK_SIZE;
i2400m->bus_pl_size_max = I2400MS_PL_SIZE_MAX;
+ i2400m->bus_setup = i2400ms_bus_setup;
i2400m->bus_dev_start = i2400ms_bus_dev_start;
- i2400m->bus_dev_stop = i2400ms_bus_dev_stop;
+ i2400m->bus_dev_stop = NULL;
+ i2400m->bus_release = i2400ms_bus_release;
i2400m->bus_tx_kick = i2400ms_bus_tx_kick;
i2400m->bus_reset = i2400ms_bus_reset;
/* The iwmc3200-wimax sometimes requires the driver to try
* hard when we paint it into a corner. */
- i2400m->bus_bm_retries = I3200_BOOT_RETRIES;
+ i2400m->bus_bm_retries = I2400M_SDIO_BOOT_RETRIES;
i2400m->bus_bm_cmd_send = i2400ms_bus_bm_cmd_send;
i2400m->bus_bm_wait_for_ack = i2400ms_bus_bm_wait_for_ack;
i2400m->bus_fw_names = i2400ms_bus_fw_names;
i2400m->bus_bm_mac_addr_impaired = 1;
i2400m->bus_bm_pokes_table = &i2400ms_pokes[0];
- sdio_claim_host(func);
- result = sdio_set_block_size(func, I2400MS_BLK_SIZE);
- sdio_release_host(func);
- if (result < 0) {
- dev_err(dev, "Failed to set block size: %d\n", result);
- goto error_set_blk_size;
- }
-
- result = i2400ms_enable_function(i2400ms->func);
- if (result < 0) {
- dev_err(dev, "Cannot enable SDIO function: %d\n", result);
- goto error_func_enable;
+ switch (func->device) {
+ case SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX:
+ case SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX_2G5:
+ i2400ms->iwmc3200 = 1;
+ break;
+ default:
+ i2400ms->iwmc3200 = 0;
}
- result = i2400ms_rx_setup(i2400ms);
- if (result < 0)
- goto error_rx_setup;
-
result = i2400m_setup(i2400m, I2400M_BRI_NO_REBOOT);
if (result < 0) {
dev_err(dev, "cannot setup device: %d\n", result);
@@ -473,13 +524,6 @@ int i2400ms_probe(struct sdio_func *func,
error_debugfs_add:
i2400m_release(i2400m);
error_setup:
- i2400ms_rx_release(i2400ms);
-error_rx_setup:
- sdio_claim_host(func);
- sdio_disable_func(func);
- sdio_release_host(func);
-error_func_enable:
-error_set_blk_size:
sdio_set_drvdata(func, NULL);
free_netdev(net_dev);
error_alloc_netdev:
@@ -497,12 +541,9 @@ void i2400ms_remove(struct sdio_func *func)
d_fnstart(3, dev, "SDIO func %p\n", func);
debugfs_remove_recursive(i2400ms->debugfs_dentry);
- i2400ms_rx_release(i2400ms);
+ i2400ms->debugfs_dentry = NULL;
i2400m_release(i2400m);
sdio_set_drvdata(func, NULL);
- sdio_claim_host(func);
- sdio_disable_func(func);
- sdio_release_host(func);
free_netdev(net_dev);
d_fnend(3, dev, "SDIO func %p\n", func);
}
@@ -512,6 +553,8 @@ const struct sdio_device_id i2400ms_sdio_ids[] = {
/* Intel: i2400m WiMAX (iwmc3200) over SDIO */
{ SDIO_DEVICE(SDIO_VENDOR_ID_INTEL,
SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX) },
+ { SDIO_DEVICE(SDIO_VENDOR_ID_INTEL,
+ SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX_2G5) },
{ /* end: all zeroes */ },
};
MODULE_DEVICE_TABLE(sdio, i2400ms_sdio_ids);
@@ -529,6 +572,8 @@ struct sdio_driver i2400m_sdio_driver = {
static
int __init i2400ms_driver_init(void)
{
+ d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400ms_debug_params,
+ "i2400m_sdio.debug");
return sdio_register_driver(&i2400m_sdio_driver);
}
module_init(i2400ms_driver_init);
diff --git a/drivers/net/wimax/i2400m/tx.c b/drivers/net/wimax/i2400m/tx.c
index fa16ccf..54480e8 100644
--- a/drivers/net/wimax/i2400m/tx.c
+++ b/drivers/net/wimax/i2400m/tx.c
@@ -310,7 +310,7 @@ size_t __i2400m_tx_tail_room(struct i2400m *i2400m)
size_t tail_room;
size_t tx_in;
- if (unlikely(i2400m->tx_in) == 0)
+ if (unlikely(i2400m->tx_in == 0))
return I2400M_TX_BUF_SIZE;
tx_in = i2400m->tx_in % I2400M_TX_BUF_SIZE;
tail_room = I2400M_TX_BUF_SIZE - tx_in;
@@ -642,6 +642,9 @@ int i2400m_tx(struct i2400m *i2400m, const void *buf, size_t buf_len,
* current one is out of payload slots or we have a singleton,
* close it and start a new one */
spin_lock_irqsave(&i2400m->tx_lock, flags);
+ result = -ESHUTDOWN;
+ if (i2400m->tx_buf == NULL)
+ goto error_tx_new;
try_new:
if (unlikely(i2400m->tx_msg == NULL))
i2400m_tx_new(i2400m);
@@ -697,7 +700,10 @@ try_new:
}
error_tx_new:
spin_unlock_irqrestore(&i2400m->tx_lock, flags);
- i2400m->bus_tx_kick(i2400m); /* always kick, might free up space */
+ /* kick in most cases, except when the TX subsys is down, as
+ * it might free space */
+ if (likely(result != -ESHUTDOWN))
+ i2400m->bus_tx_kick(i2400m);
d_fnend(3, dev, "(i2400m %p skb %p [%zu bytes] pt %u) = %d\n",
i2400m, buf, buf_len, pl_type, result);
return result;
@@ -740,6 +746,9 @@ struct i2400m_msg_hdr *i2400m_tx_msg_get(struct i2400m *i2400m,
d_fnstart(3, dev, "(i2400m %p bus_size %p)\n", i2400m, bus_size);
spin_lock_irqsave(&i2400m->tx_lock, flags);
+ tx_msg_moved = NULL;
+ if (i2400m->tx_buf == NULL)
+ goto out_unlock;
skip:
tx_msg_moved = NULL;
if (i2400m->tx_in == i2400m->tx_out) { /* Empty FIFO? */
@@ -829,6 +838,8 @@ void i2400m_tx_msg_sent(struct i2400m *i2400m)
d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
spin_lock_irqsave(&i2400m->tx_lock, flags);
+ if (i2400m->tx_buf == NULL)
+ goto out_unlock;
i2400m->tx_out += i2400m->tx_msg_size;
d_printf(2, dev, "TX: sent %zu b\n", (size_t) i2400m->tx_msg_size);
i2400m->tx_msg_size = 0;
@@ -837,6 +848,7 @@ void i2400m_tx_msg_sent(struct i2400m *i2400m)
n = i2400m->tx_out / I2400M_TX_BUF_SIZE;
i2400m->tx_out %= I2400M_TX_BUF_SIZE;
i2400m->tx_in -= n * I2400M_TX_BUF_SIZE;
+out_unlock:
spin_unlock_irqrestore(&i2400m->tx_lock, flags);
d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
}
@@ -876,5 +888,9 @@ int i2400m_tx_setup(struct i2400m *i2400m)
*/
void i2400m_tx_release(struct i2400m *i2400m)
{
+ unsigned long flags;
+ spin_lock_irqsave(&i2400m->tx_lock, flags);
kfree(i2400m->tx_buf);
+ i2400m->tx_buf = NULL;
+ spin_unlock_irqrestore(&i2400m->tx_lock, flags);
}
diff --git a/drivers/net/wimax/i2400m/usb-fw.c b/drivers/net/wimax/i2400m/usb-fw.c
index 5ad287c..ce6b993 100644
--- a/drivers/net/wimax/i2400m/usb-fw.c
+++ b/drivers/net/wimax/i2400m/usb-fw.c
@@ -99,10 +99,10 @@ ssize_t i2400mu_tx_bulk_out(struct i2400mu *i2400mu, void *buf, size_t buf_size)
dev_err(dev, "BM-CMD: can't get autopm: %d\n", result);
do_autopm = 0;
}
- epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_BULK_OUT);
+ epd = usb_get_epd(i2400mu->usb_iface, i2400mu->endpoint_cfg.bulk_out);
pipe = usb_sndbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
retry:
- result = usb_bulk_msg(i2400mu->usb_dev, pipe, buf, buf_size, &len, HZ);
+ result = usb_bulk_msg(i2400mu->usb_dev, pipe, buf, buf_size, &len, 200);
switch (result) {
case 0:
if (len != buf_size) {
@@ -113,6 +113,28 @@ retry:
}
result = len;
break;
+ case -EPIPE:
+ /*
+ * Stall -- maybe the device is choking with our
+ * requests. Clear it and give it some time. If they
+ * happen to often, it might be another symptom, so we
+ * reset.
+ *
+ * No error handling for usb_clear_halt(0; if it
+ * works, the retry works; if it fails, this switch
+ * does the error handling for us.
+ */
+ if (edc_inc(&i2400mu->urb_edc,
+ 10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+ dev_err(dev, "BM-CMD: too many stalls in "
+ "URB; resetting device\n");
+ usb_queue_reset_device(i2400mu->usb_iface);
+ /* fallthrough */
+ } else {
+ usb_clear_halt(i2400mu->usb_dev, pipe);
+ msleep(10); /* give the device some time */
+ goto retry;
+ }
case -EINVAL: /* while removing driver */
case -ENODEV: /* dev disconnect ... */
case -ENOENT: /* just ignore it */
@@ -135,7 +157,6 @@ retry:
result);
goto retry;
}
- result = len;
if (do_autopm)
usb_autopm_put_interface(i2400mu->usb_iface);
return result;
@@ -172,7 +193,8 @@ ssize_t i2400mu_bus_bm_cmd_send(struct i2400m *i2400m,
result = -E2BIG;
if (cmd_size > I2400M_BM_CMD_BUF_SIZE)
goto error_too_big;
- memcpy(i2400m->bm_cmd_buf, _cmd, cmd_size);
+ if (_cmd != i2400m->bm_cmd_buf)
+ memmove(i2400m->bm_cmd_buf, _cmd, cmd_size);
cmd = i2400m->bm_cmd_buf;
if (cmd_size_a > cmd_size) /* Zero pad space */
memset(i2400m->bm_cmd_buf + cmd_size, 0, cmd_size_a - cmd_size);
@@ -226,7 +248,8 @@ int i2400mu_notif_submit(struct i2400mu *i2400mu, struct urb *urb,
struct usb_endpoint_descriptor *epd;
int pipe;
- epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_NOTIFICATION);
+ epd = usb_get_epd(i2400mu->usb_iface,
+ i2400mu->endpoint_cfg.notification);
pipe = usb_rcvintpipe(i2400mu->usb_dev, epd->bEndpointAddress);
usb_fill_int_urb(urb, i2400mu->usb_dev, pipe,
i2400m->bm_ack_buf, I2400M_BM_ACK_BUF_SIZE,
@@ -328,8 +351,8 @@ error_dev_gone:
out:
if (do_autopm)
usb_autopm_put_interface(i2400mu->usb_iface);
- d_fnend(8, dev, "(i2400m %p ack %p size %zu) = %zd\n",
- i2400m, ack, ack_size, result);
+ d_fnend(8, dev, "(i2400m %p ack %p size %zu) = %ld\n",
+ i2400m, ack, ack_size, (long) result);
return result;
error_exceeded:
diff --git a/drivers/net/wimax/i2400m/usb-notif.c b/drivers/net/wimax/i2400m/usb-notif.c
index 6add27c..f88d1c6 100644
--- a/drivers/net/wimax/i2400m/usb-notif.c
+++ b/drivers/net/wimax/i2400m/usb-notif.c
@@ -51,6 +51,7 @@
*
* i2400mu_usb_notification_cb() Called when a URB is ready
* i2400mu_notif_grok()
+ * i2400m_is_boot_barker()
* i2400m_dev_reset_handle()
* i2400mu_rx_kick()
*/
@@ -87,32 +88,21 @@ int i2400mu_notification_grok(struct i2400mu *i2400mu, const void *buf,
d_fnstart(4, dev, "(i2400m %p buf %p buf_len %zu)\n",
i2400mu, buf, buf_len);
ret = -EIO;
- if (buf_len < sizeof(i2400m_NBOOT_BARKER))
+ if (buf_len < sizeof(i2400m_ZERO_BARKER))
/* Not a bug, just ignore */
goto error_bad_size;
- if (!memcmp(i2400m_NBOOT_BARKER, buf, sizeof(i2400m_NBOOT_BARKER))
- || !memcmp(i2400m_SBOOT_BARKER, buf, sizeof(i2400m_SBOOT_BARKER)))
- ret = i2400m_dev_reset_handle(i2400m);
- else if (!memcmp(i2400m_ZERO_BARKER, buf, sizeof(i2400m_ZERO_BARKER))) {
+ ret = 0;
+ if (!memcmp(i2400m_ZERO_BARKER, buf, sizeof(i2400m_ZERO_BARKER))) {
i2400mu_rx_kick(i2400mu);
- ret = 0;
- } else { /* Unknown or unexpected data in the notif message */
- char prefix[64];
- ret = -EIO;
- dev_err(dev, "HW BUG? Unknown/unexpected data in notification "
- "message (%zu bytes)\n", buf_len);
- snprintf(prefix, sizeof(prefix), "%s %s: ",
- dev_driver_string(dev), dev_name(dev));
- if (buf_len > 64) {
- print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
- 8, 4, buf, 64, 0);
- printk(KERN_ERR "%s... (only first 64 bytes "
- "dumped)\n", prefix);
- } else
- print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
- 8, 4, buf, buf_len, 0);
+ goto out;
}
+ ret = i2400m_is_boot_barker(i2400m, buf, buf_len);
+ if (unlikely(ret >= 0))
+ ret = i2400m_dev_reset_handle(i2400m, "device rebooted");
+ else /* Unknown or unexpected data in the notif message */
+ i2400m_unknown_barker(i2400m, buf, buf_len);
error_bad_size:
+out:
d_fnend(4, dev, "(i2400m %p buf %p buf_len %zu) = %d\n",
i2400mu, buf, buf_len, ret);
return ret;
@@ -220,7 +210,8 @@ int i2400mu_notification_setup(struct i2400mu *i2400mu)
dev_err(dev, "notification: cannot allocate URB\n");
goto error_alloc_urb;
}
- epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_NOTIFICATION);
+ epd = usb_get_epd(i2400mu->usb_iface,
+ i2400mu->endpoint_cfg.notification);
usb_pipe = usb_rcvintpipe(i2400mu->usb_dev, epd->bEndpointAddress);
usb_fill_int_urb(i2400mu->notif_urb, i2400mu->usb_dev, usb_pipe,
buf, I2400MU_MAX_NOTIFICATION_LEN,
diff --git a/drivers/net/wimax/i2400m/usb-rx.c b/drivers/net/wimax/i2400m/usb-rx.c
index a314799..ba1b023 100644
--- a/drivers/net/wimax/i2400m/usb-rx.c
+++ b/drivers/net/wimax/i2400m/usb-rx.c
@@ -204,7 +204,7 @@ struct sk_buff *i2400mu_rx(struct i2400mu *i2400mu, struct sk_buff *rx_skb)
dev_err(dev, "RX: can't get autopm: %d\n", result);
do_autopm = 0;
}
- epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_BULK_IN);
+ epd = usb_get_epd(i2400mu->usb_iface, i2400mu->endpoint_cfg.bulk_in);
usb_pipe = usb_rcvbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
retry:
rx_size = skb_end_pointer(rx_skb) - rx_skb->data - rx_skb->len;
@@ -214,7 +214,7 @@ retry:
}
result = usb_bulk_msg(
i2400mu->usb_dev, usb_pipe, rx_skb->data + rx_skb->len,
- rx_size, &read_size, HZ);
+ rx_size, &read_size, 200);
usb_mark_last_busy(i2400mu->usb_dev);
switch (result) {
case 0:
@@ -222,6 +222,26 @@ retry:
goto retry; /* ZLP, just resubmit */
skb_put(rx_skb, read_size);
break;
+ case -EPIPE:
+ /*
+ * Stall -- maybe the device is choking with our
+ * requests. Clear it and give it some time. If they
+ * happen to often, it might be another symptom, so we
+ * reset.
+ *
+ * No error handling for usb_clear_halt(0; if it
+ * works, the retry works; if it fails, this switch
+ * does the error handling for us.
+ */
+ if (edc_inc(&i2400mu->urb_edc,
+ 10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+ dev_err(dev, "BM-CMD: too many stalls in "
+ "URB; resetting device\n");
+ goto do_reset;
+ }
+ usb_clear_halt(i2400mu->usb_dev, usb_pipe);
+ msleep(10); /* give the device some time */
+ goto retry;
case -EINVAL: /* while removing driver */
case -ENODEV: /* dev disconnect ... */
case -ENOENT: /* just ignore it */
@@ -283,6 +303,7 @@ out:
error_reset:
dev_err(dev, "RX: maximum errors in URB exceeded; "
"resetting device\n");
+do_reset:
usb_queue_reset_device(i2400mu->usb_iface);
rx_skb = ERR_PTR(result);
goto out;
@@ -316,10 +337,15 @@ int i2400mu_rxd(void *_i2400mu)
size_t pending;
int rx_size;
struct sk_buff *rx_skb;
+ unsigned long flags;
d_fnstart(4, dev, "(i2400mu %p)\n", i2400mu);
+ spin_lock_irqsave(&i2400m->rx_lock, flags);
+ BUG_ON(i2400mu->rx_kthread != NULL);
+ i2400mu->rx_kthread = current;
+ spin_unlock_irqrestore(&i2400m->rx_lock, flags);
while (1) {
- d_printf(2, dev, "TX: waiting for messages\n");
+ d_printf(2, dev, "RX: waiting for messages\n");
pending = 0;
wait_event_interruptible(
i2400mu->rx_wq,
@@ -367,6 +393,9 @@ int i2400mu_rxd(void *_i2400mu)
}
result = 0;
out:
+ spin_lock_irqsave(&i2400m->rx_lock, flags);
+ i2400mu->rx_kthread = NULL;
+ spin_unlock_irqrestore(&i2400m->rx_lock, flags);
d_fnend(4, dev, "(i2400mu %p) = %d\n", i2400mu, result);
return result;
@@ -403,18 +432,33 @@ int i2400mu_rx_setup(struct i2400mu *i2400mu)
struct i2400m *i2400m = &i2400mu->i2400m;
struct device *dev = &i2400mu->usb_iface->dev;
struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
+ struct task_struct *kthread;
- i2400mu->rx_kthread = kthread_run(i2400mu_rxd, i2400mu, "%s-rx",
- wimax_dev->name);
- if (IS_ERR(i2400mu->rx_kthread)) {
- result = PTR_ERR(i2400mu->rx_kthread);
+ kthread = kthread_run(i2400mu_rxd, i2400mu, "%s-rx",
+ wimax_dev->name);
+ /* the kthread function sets i2400mu->rx_thread */
+ if (IS_ERR(kthread)) {
+ result = PTR_ERR(kthread);
dev_err(dev, "RX: cannot start thread: %d\n", result);
}
return result;
}
+
void i2400mu_rx_release(struct i2400mu *i2400mu)
{
- kthread_stop(i2400mu->rx_kthread);
+ unsigned long flags;
+ struct i2400m *i2400m = &i2400mu->i2400m;
+ struct device *dev = i2400m_dev(i2400m);
+ struct task_struct *kthread;
+
+ spin_lock_irqsave(&i2400m->rx_lock, flags);
+ kthread = i2400mu->rx_kthread;
+ i2400mu->rx_kthread = NULL;
+ spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+ if (kthread)
+ kthread_stop(kthread);
+ else
+ d_printf(1, dev, "RX: kthread had already exited\n");
}
diff --git a/drivers/net/wimax/i2400m/usb-tx.c b/drivers/net/wimax/i2400m/usb-tx.c
index dfd8933..c65b997 100644
--- a/drivers/net/wimax/i2400m/usb-tx.c
+++ b/drivers/net/wimax/i2400m/usb-tx.c
@@ -101,11 +101,11 @@ int i2400mu_tx(struct i2400mu *i2400mu, struct i2400m_msg_hdr *tx_msg,
dev_err(dev, "TX: can't get autopm: %d\n", result);
do_autopm = 0;
}
- epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_BULK_OUT);
+ epd = usb_get_epd(i2400mu->usb_iface, i2400mu->endpoint_cfg.bulk_out);
usb_pipe = usb_sndbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
retry:
result = usb_bulk_msg(i2400mu->usb_dev, usb_pipe,
- tx_msg, tx_msg_size, &sent_size, HZ);
+ tx_msg, tx_msg_size, &sent_size, 200);
usb_mark_last_busy(i2400mu->usb_dev);
switch (result) {
case 0:
@@ -115,6 +115,28 @@ retry:
result = -EIO;
}
break;
+ case -EPIPE:
+ /*
+ * Stall -- maybe the device is choking with our
+ * requests. Clear it and give it some time. If they
+ * happen to often, it might be another symptom, so we
+ * reset.
+ *
+ * No error handling for usb_clear_halt(0; if it
+ * works, the retry works; if it fails, this switch
+ * does the error handling for us.
+ */
+ if (edc_inc(&i2400mu->urb_edc,
+ 10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+ dev_err(dev, "BM-CMD: too many stalls in "
+ "URB; resetting device\n");
+ usb_queue_reset_device(i2400mu->usb_iface);
+ /* fallthrough */
+ } else {
+ usb_clear_halt(i2400mu->usb_dev, usb_pipe);
+ msleep(10); /* give the device some time */
+ goto retry;
+ }
case -EINVAL: /* while removing driver */
case -ENODEV: /* dev disconnect ... */
case -ENOENT: /* just ignore it */
@@ -161,9 +183,15 @@ int i2400mu_txd(void *_i2400mu)
struct device *dev = &i2400mu->usb_iface->dev;
struct i2400m_msg_hdr *tx_msg;
size_t tx_msg_size;
+ unsigned long flags;
d_fnstart(4, dev, "(i2400mu %p)\n", i2400mu);
+ spin_lock_irqsave(&i2400m->tx_lock, flags);
+ BUG_ON(i2400mu->tx_kthread != NULL);
+ i2400mu->tx_kthread = current;
+ spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+
while (1) {
d_printf(2, dev, "TX: waiting for messages\n");
tx_msg = NULL;
@@ -183,6 +211,11 @@ int i2400mu_txd(void *_i2400mu)
if (result < 0)
break;
}
+
+ spin_lock_irqsave(&i2400m->tx_lock, flags);
+ i2400mu->tx_kthread = NULL;
+ spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+
d_fnend(4, dev, "(i2400mu %p) = %d\n", i2400mu, result);
return result;
}
@@ -213,11 +246,13 @@ int i2400mu_tx_setup(struct i2400mu *i2400mu)
struct i2400m *i2400m = &i2400mu->i2400m;
struct device *dev = &i2400mu->usb_iface->dev;
struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
+ struct task_struct *kthread;
- i2400mu->tx_kthread = kthread_run(i2400mu_txd, i2400mu, "%s-tx",
- wimax_dev->name);
- if (IS_ERR(i2400mu->tx_kthread)) {
- result = PTR_ERR(i2400mu->tx_kthread);
+ kthread = kthread_run(i2400mu_txd, i2400mu, "%s-tx",
+ wimax_dev->name);
+ /* the kthread function sets i2400mu->tx_thread */
+ if (IS_ERR(kthread)) {
+ result = PTR_ERR(kthread);
dev_err(dev, "TX: cannot start thread: %d\n", result);
}
return result;
@@ -225,5 +260,17 @@ int i2400mu_tx_setup(struct i2400mu *i2400mu)
void i2400mu_tx_release(struct i2400mu *i2400mu)
{
- kthread_stop(i2400mu->tx_kthread);
+ unsigned long flags;
+ struct i2400m *i2400m = &i2400mu->i2400m;
+ struct device *dev = i2400m_dev(i2400m);
+ struct task_struct *kthread;
+
+ spin_lock_irqsave(&i2400m->tx_lock, flags);
+ kthread = i2400mu->tx_kthread;
+ i2400mu->tx_kthread = NULL;
+ spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+ if (kthread)
+ kthread_stop(kthread);
+ else
+ d_printf(1, dev, "TX: kthread had already exited\n");
}
diff --git a/drivers/net/wimax/i2400m/usb.c b/drivers/net/wimax/i2400m/usb.c
index 7eadd11..47e84ef 100644
--- a/drivers/net/wimax/i2400m/usb.c
+++ b/drivers/net/wimax/i2400m/usb.c
@@ -58,7 +58,7 @@
* i2400mu_rx_release()
* i2400mu_tx_release()
*
- * i2400mu_bus_reset() Called by i2400m->bus_reset
+ * i2400mu_bus_reset() Called by i2400m_reset
* __i2400mu_reset()
* __i2400mu_send_barker()
* usb_reset_device()
@@ -71,13 +71,25 @@
#define D_SUBMODULE usb
#include "usb-debug-levels.h"
+static char i2400mu_debug_params[128];
+module_param_string(debug, i2400mu_debug_params, sizeof(i2400mu_debug_params),
+ 0644);
+MODULE_PARM_DESC(debug,
+ "String of space-separated NAME:VALUE pairs, where NAMEs "
+ "are the different debug submodules and VALUE are the "
+ "initial debug value to set.");
/* Our firmware file name */
-static const char *i2400mu_bus_fw_names[] = {
+static const char *i2400mu_bus_fw_names_5x50[] = {
#define I2400MU_FW_FILE_NAME_v1_4 "i2400m-fw-usb-1.4.sbcf"
I2400MU_FW_FILE_NAME_v1_4,
-#define I2400MU_FW_FILE_NAME_v1_3 "i2400m-fw-usb-1.3.sbcf"
- I2400MU_FW_FILE_NAME_v1_3,
+ NULL,
+};
+
+
+static const char *i2400mu_bus_fw_names_6050[] = {
+#define I6050U_FW_FILE_NAME_v1_5 "i6050-fw-usb-1.5.sbcf"
+ I6050U_FW_FILE_NAME_v1_5,
NULL,
};
@@ -160,14 +172,59 @@ int __i2400mu_send_barker(struct i2400mu *i2400mu,
epd = usb_get_epd(i2400mu->usb_iface, endpoint);
pipe = usb_sndbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
memcpy(buffer, barker, barker_size);
+retry:
ret = usb_bulk_msg(i2400mu->usb_dev, pipe, buffer, barker_size,
- &actual_len, HZ);
- if (ret < 0) {
- if (ret != -EINVAL)
- dev_err(dev, "E: barker error: %d\n", ret);
- } else if (actual_len != barker_size) {
- dev_err(dev, "E: only %d bytes transmitted\n", actual_len);
- ret = -EIO;
+ &actual_len, 200);
+ switch (ret) {
+ case 0:
+ if (actual_len != barker_size) { /* Too short? drop it */
+ dev_err(dev, "E: %s: short write (%d B vs %zu "
+ "expected)\n",
+ __func__, actual_len, barker_size);
+ ret = -EIO;
+ }
+ break;
+ case -EPIPE:
+ /*
+ * Stall -- maybe the device is choking with our
+ * requests. Clear it and give it some time. If they
+ * happen to often, it might be another symptom, so we
+ * reset.
+ *
+ * No error handling for usb_clear_halt(0; if it
+ * works, the retry works; if it fails, this switch
+ * does the error handling for us.
+ */
+ if (edc_inc(&i2400mu->urb_edc,
+ 10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+ dev_err(dev, "E: %s: too many stalls in "
+ "URB; resetting device\n", __func__);
+ usb_queue_reset_device(i2400mu->usb_iface);
+ /* fallthrough */
+ } else {
+ usb_clear_halt(i2400mu->usb_dev, pipe);
+ msleep(10); /* give the device some time */
+ goto retry;
+ }
+ case -EINVAL: /* while removing driver */
+ case -ENODEV: /* dev disconnect ... */
+ case -ENOENT: /* just ignore it */
+ case -ESHUTDOWN: /* and exit */
+ case -ECONNRESET:
+ ret = -ESHUTDOWN;
+ break;
+ default: /* Some error? */
+ if (edc_inc(&i2400mu->urb_edc,
+ EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+ dev_err(dev, "E: %s: maximum errors in URB "
+ "exceeded; resetting device\n",
+ __func__);
+ usb_queue_reset_device(i2400mu->usb_iface);
+ } else {
+ dev_warn(dev, "W: %s: cannot send URB: %d\n",
+ __func__, ret);
+ goto retry;
+ }
}
kfree(buffer);
error_kzalloc:
@@ -232,15 +289,16 @@ int i2400mu_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
d_fnstart(3, dev, "(i2400m %p rt %u)\n", i2400m, rt);
if (rt == I2400M_RT_WARM)
- result = __i2400mu_send_barker(i2400mu, i2400m_WARM_BOOT_BARKER,
- sizeof(i2400m_WARM_BOOT_BARKER),
- I2400MU_EP_BULK_OUT);
+ result = __i2400mu_send_barker(
+ i2400mu, i2400m_WARM_BOOT_BARKER,
+ sizeof(i2400m_WARM_BOOT_BARKER),
+ i2400mu->endpoint_cfg.bulk_out);
else if (rt == I2400M_RT_COLD)
- result = __i2400mu_send_barker(i2400mu, i2400m_COLD_BOOT_BARKER,
- sizeof(i2400m_COLD_BOOT_BARKER),
- I2400MU_EP_RESET_COLD);
+ result = __i2400mu_send_barker(
+ i2400mu, i2400m_COLD_BOOT_BARKER,
+ sizeof(i2400m_COLD_BOOT_BARKER),
+ i2400mu->endpoint_cfg.reset_cold);
else if (rt == I2400M_RT_BUS) {
-do_bus_reset:
result = usb_reset_device(i2400mu->usb_dev);
switch (result) {
case 0:
@@ -248,7 +306,7 @@ do_bus_reset:
case -ENODEV:
case -ENOENT:
case -ESHUTDOWN:
- result = rt == I2400M_RT_WARM ? -ENODEV : 0;
+ result = 0;
break; /* We assume the device is disconnected */
default:
dev_err(dev, "USB reset failed (%d), giving up!\n",
@@ -261,10 +319,17 @@ do_bus_reset:
if (result < 0
&& result != -EINVAL /* device is gone */
&& rt != I2400M_RT_BUS) {
+ /*
+ * Things failed -- resort to lower level reset, that
+ * we queue in another context; the reason for this is
+ * that the pre and post reset functionality requires
+ * the i2400m->init_mutex; RT_WARM and RT_COLD can
+ * come from areas where i2400m->init_mutex is taken.
+ */
dev_err(dev, "%s reset failed (%d); trying USB reset\n",
rt == I2400M_RT_WARM ? "warm" : "cold", result);
- rt = I2400M_RT_BUS;
- goto do_bus_reset;
+ usb_queue_reset_device(i2400mu->usb_iface);
+ result = -ENODEV;
}
d_fnend(3, dev, "(i2400m %p rt %u) = %d\n", i2400m, rt, result);
return result;
@@ -402,20 +467,33 @@ int i2400mu_probe(struct usb_interface *iface,
i2400m->bus_tx_block_size = I2400MU_BLK_SIZE;
i2400m->bus_pl_size_max = I2400MU_PL_SIZE_MAX;
+ i2400m->bus_setup = NULL;
i2400m->bus_dev_start = i2400mu_bus_dev_start;
i2400m->bus_dev_stop = i2400mu_bus_dev_stop;
+ i2400m->bus_release = NULL;
i2400m->bus_tx_kick = i2400mu_bus_tx_kick;
i2400m->bus_reset = i2400mu_bus_reset;
- i2400m->bus_bm_retries = I2400M_BOOT_RETRIES;
+ i2400m->bus_bm_retries = I2400M_USB_BOOT_RETRIES;
i2400m->bus_bm_cmd_send = i2400mu_bus_bm_cmd_send;
i2400m->bus_bm_wait_for_ack = i2400mu_bus_bm_wait_for_ack;
- i2400m->bus_fw_names = i2400mu_bus_fw_names;
i2400m->bus_bm_mac_addr_impaired = 0;
+ if (id->idProduct == USB_DEVICE_ID_I6050) {
+ i2400m->bus_fw_names = i2400mu_bus_fw_names_6050;
+ i2400mu->endpoint_cfg.bulk_out = 0;
+ i2400mu->endpoint_cfg.notification = 3;
+ i2400mu->endpoint_cfg.reset_cold = 2;
+ i2400mu->endpoint_cfg.bulk_in = 1;
+ } else {
+ i2400m->bus_fw_names = i2400mu_bus_fw_names_5x50;
+ i2400mu->endpoint_cfg.bulk_out = 0;
+ i2400mu->endpoint_cfg.notification = 1;
+ i2400mu->endpoint_cfg.reset_cold = 2;
+ i2400mu->endpoint_cfg.bulk_in = 3;
+ }
#ifdef CONFIG_PM
iface->needs_remote_wakeup = 1; /* autosuspend (15s delay) */
device_init_wakeup(dev, 1);
- usb_autopm_enable(i2400mu->usb_iface);
usb_dev->autosuspend_delay = 15 * HZ;
usb_dev->autosuspend_disabled = 0;
#endif
@@ -483,7 +561,10 @@ void i2400mu_disconnect(struct usb_interface *iface)
* So at the end, the three cases require common handling.
*
* If at the time of this call the device's firmware is not loaded,
- * nothing has to be done.
+ * nothing has to be done. Note we can be "loose" about not reading
+ * i2400m->updown under i2400m->init_mutex. If it happens to change
+ * inmediately, other parts of the call flow will fail and effectively
+ * catch it.
*
* If the firmware is loaded, we need to:
*
@@ -522,6 +603,7 @@ int i2400mu_suspend(struct usb_interface *iface, pm_message_t pm_msg)
#endif
d_fnstart(3, dev, "(iface %p pm_msg %u)\n", iface, pm_msg.event);
+ rmb(); /* see i2400m->updown's documentation */
if (i2400m->updown == 0)
goto no_firmware;
if (i2400m->state == I2400M_SS_DATA_PATH_CONNECTED && is_autosuspend) {
@@ -575,6 +657,7 @@ int i2400mu_resume(struct usb_interface *iface)
struct i2400m *i2400m = &i2400mu->i2400m;
d_fnstart(3, dev, "(iface %p)\n", iface);
+ rmb(); /* see i2400m->updown's documentation */
if (i2400m->updown == 0) {
d_printf(1, dev, "fw was down, no resume neeed\n");
goto out;
@@ -591,7 +674,54 @@ out:
static
+int i2400mu_reset_resume(struct usb_interface *iface)
+{
+ int result;
+ struct device *dev = &iface->dev;
+ struct i2400mu *i2400mu = usb_get_intfdata(iface);
+ struct i2400m *i2400m = &i2400mu->i2400m;
+
+ d_fnstart(3, dev, "(iface %p)\n", iface);
+ result = i2400m_dev_reset_handle(i2400m, "device reset on resume");
+ d_fnend(3, dev, "(iface %p) = %d\n", iface, result);
+ return result < 0 ? result : 0;
+}
+
+
+/*
+ * Another driver or user space is triggering a reset on the device
+ * which contains the interface passed as an argument. Cease IO and
+ * save any device state you need to restore.
+ *
+ * If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if
+ * you are in atomic context.
+ */
+static
+int i2400mu_pre_reset(struct usb_interface *iface)
+{
+ struct i2400mu *i2400mu = usb_get_intfdata(iface);
+ return i2400m_pre_reset(&i2400mu->i2400m);
+}
+
+
+/*
+ * The reset has completed. Restore any saved device state and begin
+ * using the device again.
+ *
+ * If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if
+ * you are in atomic context.
+ */
+static
+int i2400mu_post_reset(struct usb_interface *iface)
+{
+ struct i2400mu *i2400mu = usb_get_intfdata(iface);
+ return i2400m_post_reset(&i2400mu->i2400m);
+}
+
+
+static
struct usb_device_id i2400mu_id_table[] = {
+ { USB_DEVICE(0x8086, USB_DEVICE_ID_I6050) },
{ USB_DEVICE(0x8086, 0x0181) },
{ USB_DEVICE(0x8086, 0x1403) },
{ USB_DEVICE(0x8086, 0x1405) },
@@ -609,8 +739,11 @@ struct usb_driver i2400mu_driver = {
.name = KBUILD_MODNAME,
.suspend = i2400mu_suspend,
.resume = i2400mu_resume,
+ .reset_resume = i2400mu_reset_resume,
.probe = i2400mu_probe,
.disconnect = i2400mu_disconnect,
+ .pre_reset = i2400mu_pre_reset,
+ .post_reset = i2400mu_post_reset,
.id_table = i2400mu_id_table,
.supports_autosuspend = 1,
};
@@ -618,6 +751,8 @@ struct usb_driver i2400mu_driver = {
static
int __init i2400mu_driver_init(void)
{
+ d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400mu_debug_params,
+ "i2400m_usb.debug");
return usb_register(&i2400mu_driver);
}
module_init(i2400mu_driver_init);
@@ -632,7 +767,7 @@ void __exit i2400mu_driver_exit(void)
module_exit(i2400mu_driver_exit);
MODULE_AUTHOR("Intel Corporation <linux-wimax@intel.com>");
-MODULE_DESCRIPTION("Intel 2400M WiMAX networking for USB");
+MODULE_DESCRIPTION("Driver for USB based Intel Wireless WiMAX Connection 2400M "
+ "(5x50 & 6050)");
MODULE_LICENSE("GPL");
MODULE_FIRMWARE(I2400MU_FW_FILE_NAME_v1_4);
-MODULE_FIRMWARE(I2400MU_FW_FILE_NAME_v1_3);
generated by cgit v1.1 at 2024-12-27 10:59:14 +0000