diff options
Diffstat (limited to 'include/asm-arm/arch-at91rm9200/board.h')
| -rw-r--r-- | include/asm-arm/arch-at91rm9200/board.h | 117 |
1 files changed, 0 insertions, 117 deletions
diff --git a/include/asm-arm/arch-at91rm9200/board.h b/include/asm-arm/arch-at91rm9200/board.h deleted file mode 100644 index 768e0fc..0000000 --- a/include/asm-arm/arch-at91rm9200/board.h +++ /dev/null @@ -1,117 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/board.h - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -/* - * These are data structures found in platform_device.dev.platform_data, - * and describing board-specific data needed by drivers. For example, - * which pin is used for a given GPIO role. - * - * In 2.6, drivers should strongly avoid board-specific knowledge so - * that supporting new boards normally won't require driver patches. - * Most board-specific knowledge should be in arch/.../board-*.c files. - */ - -#ifndef __ASM_ARCH_BOARD_H -#define __ASM_ARCH_BOARD_H - -#include <linux/mtd/partitions.h> -#include <linux/device.h> -#include <linux/spi/spi.h> - - /* USB Device */ -struct at91_udc_data { - u8 vbus_pin; /* high == host powering us */ - u8 pullup_pin; /* high == D+ pulled up */ -}; -extern void __init at91_add_device_udc(struct at91_udc_data *data); - - /* Compact Flash */ -struct at91_cf_data { - u8 irq_pin; /* I/O IRQ */ - u8 det_pin; /* Card detect */ - u8 vcc_pin; /* power switching */ - u8 rst_pin; /* card reset */ - u8 chipselect; /* EBI Chip Select number */ -}; -extern void __init at91_add_device_cf(struct at91_cf_data *data); - - /* MMC / SD */ -struct at91_mmc_data { - u8 det_pin; /* card detect IRQ */ - unsigned slot_b:1; /* uses Slot B */ - unsigned wire4:1; /* (SD) supports DAT0..DAT3 */ - u8 wp_pin; /* (SD) writeprotect detect */ - u8 vcc_pin; /* power switching (high == on) */ -}; -extern void __init at91_add_device_mmc(struct at91_mmc_data *data); - - /* Ethernet */ -struct at91_eth_data { - u8 phy_irq_pin; /* PHY IRQ */ - u8 is_rmii; /* using RMII interface? */ -}; -extern void __init at91_add_device_eth(struct at91_eth_data *data); - - /* USB Host */ -struct at91_usbh_data { - u8 ports; /* number of ports on root hub */ -}; -extern void __init at91_add_device_usbh(struct at91_usbh_data *data); - - /* NAND / SmartMedia */ -struct at91_nand_data { - u8 enable_pin; /* chip enable */ - u8 det_pin; /* card detect */ - u8 rdy_pin; /* ready/busy */ - u8 ale; /* address line number connected to ALE */ - u8 cle; /* address line number connected to CLE */ - u8 bus_width_16; /* buswidth is 16 bit */ - struct mtd_partition* (*partition_info)(int, int*); -}; -extern void __init at91_add_device_nand(struct at91_nand_data *data); - - /* I2C*/ -extern void __init at91_add_device_i2c(void); - - /* SPI */ -extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices); - - /* Serial */ -struct at91_uart_config { - unsigned short console_tty; /* tty number of serial console */ - unsigned short nr_tty; /* number of serial tty's */ - short tty_map[]; /* map UART to tty number */ -}; -extern struct platform_device *atmel_default_console_device; -extern void __init at91_init_serial(struct at91_uart_config *config); - -struct atmel_uart_data { - short use_dma_tx; /* use transmit DMA? */ - short use_dma_rx; /* use receive DMA? */ - void __iomem *regs; /* virtual base address, if any */ -}; -extern void __init at91_add_device_serial(void); - - /* LEDs */ -extern u8 at91_leds_cpu; -extern u8 at91_leds_timer; -extern void __init at91_init_leds(u8 cpu_led, u8 timer_led); - -#endif |