1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
|
/**
* @file arch/alpha/oprofile/op_model_ev5.c
*
* @remark Copyright 2002 OProfile authors
* @remark Read the file COPYING
*
* @author Richard Henderson <rth@twiddle.net>
*/
#include <linux/oprofile.h>
#include <linux/init.h>
#include <linux/smp.h>
#include <asm/ptrace.h>
#include <asm/system.h>
#include "op_impl.h"
/* Compute all of the registers in preparation for enabling profiling.
The 21164 (EV5) and 21164PC (PCA65) vary in the bit placement and
meaning of the "CBOX" events. Given that we don't care about meaning
at this point, arrange for the difference in bit placement to be
handled by common code. */
static void
common_reg_setup(struct op_register_config *reg,
struct op_counter_config *ctr,
struct op_system_config *sys,
int cbox1_ofs, int cbox2_ofs)
{
int i, ctl, reset, need_reset;
/* Select desired events. The event numbers are selected such
that they map directly into the event selection fields:
PCSEL0: 0, 1
PCSEL1: 24-39
CBOX1: 40-47
PCSEL2: 48-63
CBOX2: 64-71
There are two special cases, in that CYCLES can be measured
on PCSEL[02], and SCACHE_WRITE can be measured on CBOX[12].
These event numbers are canonicalizes to their first appearance. */
ctl = 0;
for (i = 0; i < 3; ++i) {
unsigned long event = ctr[i].event;
if (!ctr[i].enabled)
continue;
/* Remap the duplicate events, as described above. */
if (i == 2) {
if (event == 0)
event = 12+48;
else if (event == 2+41)
event = 4+65;
}
/* Convert the event numbers onto mux_select bit mask. */
if (event < 2)
ctl |= event << 31;
else if (event < 24)
/* error */;
else if (event < 40)
ctl |= (event - 24) << 4;
else if (event < 48)
ctl |= (event - 40) << cbox1_ofs | 15 << 4;
else if (event < 64)
ctl |= event - 48;
else if (event < 72)
ctl |= (event - 64) << cbox2_ofs | 15;
}
reg->mux_select = ctl;
/* Select processor mode. */
/* ??? Need to come up with some mechanism to trace only selected
processes. For now select from pal, kernel and user mode. */
ctl = 0;
ctl |= !sys->enable_pal << 9;
ctl |= !sys->enable_kernel << 8;
ctl |= !sys->enable_user << 30;
reg->proc_mode = ctl;
/* Select interrupt frequencies. Take the interrupt count selected
by the user, and map it onto one of the possible counter widths.
If the user value is in between, compute a value to which the
counter is reset at each interrupt. */
ctl = reset = need_reset = 0;
for (i = 0; i < 3; ++i) {
unsigned long max, hilo, count = ctr[i].count;
if (!ctr[i].enabled)
continue;
if (count <= 256)
count = 256, hilo = 3, max = 256;
else {
max = (i == 2 ? 16384 : 65536);
hilo = 2;
if (count > max)
count = max;
}
ctr[i].count = count;
ctl |= hilo << (8 - i*2);
reset |= (max - count) << (48 - 16*i);
if (count != max)
need_reset |= 1 << i;
}
reg->freq = ctl;
reg->reset_values = reset;
reg->need_reset = need_reset;
}
static void
ev5_reg_setup(struct op_register_config *reg,
struct op_counter_config *ctr,
struct op_system_config *sys)
{
common_reg_setup(reg, ctr, sys, 19, 22);
}
static void
pca56_reg_setup(struct op_register_config *reg,
struct op_counter_config *ctr,
struct op_system_config *sys)
{
common_reg_setup(reg, ctr, sys, 8, 11);
}
/* Program all of the registers in preparation for enabling profiling. */
static void
ev5_cpu_setup (void *x)
{
struct op_register_config *reg = x;
wrperfmon(2, reg->mux_select);
wrperfmon(3, reg->proc_mode);
wrperfmon(4, reg->freq);
wrperfmon(6, reg->reset_values);
}
/* CTR is a counter for which the user has requested an interrupt count
in between one of the widths selectable in hardware. Reset the count
for CTR to the value stored in REG->RESET_VALUES.
For EV5, this means disabling profiling, reading the current values,
masking in the value for the desired register, writing, then turning
profiling back on.
This can be streamlined if profiling is only enabled for user mode.
In that case we know that the counters are not currently incrementing
(due to being in kernel mode). */
static void
ev5_reset_ctr(struct op_register_config *reg, unsigned long ctr)
{
unsigned long values, mask, not_pk, reset_values;
mask = (ctr == 0 ? 0xfffful << 48
: ctr == 1 ? 0xfffful << 32
: 0x3fff << 16);
not_pk = 1 << 9 | 1 << 8;
reset_values = reg->reset_values;
if ((reg->proc_mode & not_pk) == not_pk) {
values = wrperfmon(5, 0);
values = (reset_values & mask) | (values & ~mask & -2);
wrperfmon(6, values);
} else {
wrperfmon(0, -1);
values = wrperfmon(5, 0);
values = (reset_values & mask) | (values & ~mask & -2);
wrperfmon(6, values);
wrperfmon(1, reg->enable);
}
}
static void
ev5_handle_interrupt(unsigned long which, struct pt_regs *regs,
struct op_counter_config *ctr)
{
/* Record the sample. */
oprofile_add_sample(regs, which);
}
struct op_axp_model op_model_ev5 = {
.reg_setup = ev5_reg_setup,
.cpu_setup = ev5_cpu_setup,
.reset_ctr = ev5_reset_ctr,
.handle_interrupt = ev5_handle_interrupt,
.cpu_type = "alpha/ev5",
.num_counters = 3,
.can_set_proc_mode = 1,
};
struct op_axp_model op_model_pca56 = {
.reg_setup = pca56_reg_setup,
.cpu_setup = ev5_cpu_setup,
.reset_ctr = ev5_reset_ctr,
.handle_interrupt = ev5_handle_interrupt,
.cpu_type = "alpha/pca56",
.num_counters = 3,
.can_set_proc_mode = 1,
};
|
