1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
|
#ifndef __SPI_BITBANG_H
#define __SPI_BITBANG_H
/*
* Mix this utility code with some glue code to get one of several types of
* simple SPI master driver. Two do polled word-at-a-time I/O:
*
* - GPIO/parport bitbangers. Provide chipselect() and txrx_word[](),
* expanding the per-word routines from the inline templates below.
*
* - Drivers for controllers resembling bare shift registers. Provide
* chipselect() and txrx_word[](), with custom setup()/cleanup() methods
* that use your controller's clock and chipselect registers.
*
* Some hardware works well with requests at spi_transfer scope:
*
* - Drivers leveraging smarter hardware, with fifos or DMA; or for half
* duplex (MicroWire) controllers. Provide chipslect() and txrx_bufs(),
* and custom setup()/cleanup() methods.
*/
struct spi_bitbang {
struct workqueue_struct *workqueue;
struct work_struct work;
spinlock_t lock;
struct list_head queue;
u8 busy;
u8 use_dma;
u8 flags; /* extra spi->mode support */
struct spi_master *master;
/* setup_transfer() changes clock and/or wordsize to match settings
* for this transfer; zeroes restore defaults from spi_device.
*/
int (*setup_transfer)(struct spi_device *spi,
struct spi_transfer *t);
void (*chipselect)(struct spi_device *spi, int is_on);
#define BITBANG_CS_ACTIVE 1 /* normally nCS, active low */
#define BITBANG_CS_INACTIVE 0
/* txrx_bufs() may handle dma mapping for transfers that don't
* already have one (transfer.{tx,rx}_dma is zero), or use PIO
*/
int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t);
/* txrx_word[SPI_MODE_*]() just looks like a shift register */
u32 (*txrx_word[4])(struct spi_device *spi,
unsigned nsecs,
u32 word, u8 bits);
};
/* you can call these default bitbang->master methods from your custom
* methods, if you like.
*/
extern int spi_bitbang_setup(struct spi_device *spi);
extern void spi_bitbang_cleanup(struct spi_device *spi);
extern int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m);
extern int spi_bitbang_setup_transfer(struct spi_device *spi,
struct spi_transfer *t);
/* start or stop queue processing */
extern int spi_bitbang_start(struct spi_bitbang *spi);
extern int spi_bitbang_stop(struct spi_bitbang *spi);
#endif /* __SPI_BITBANG_H */
/*-------------------------------------------------------------------------*/
#ifdef EXPAND_BITBANG_TXRX
/*
* The code that knows what GPIO pins do what should have declared four
* functions, ideally as inlines, before #defining EXPAND_BITBANG_TXRX
* and including this header:
*
* void setsck(struct spi_device *, int is_on);
* void setmosi(struct spi_device *, int is_on);
* int getmiso(struct spi_device *);
* void spidelay(unsigned);
*
* A non-inlined routine would call bitbang_txrx_*() routines. The
* main loop could easily compile down to a handful of instructions,
* especially if the delay is a NOP (to run at peak speed).
*
* Since this is software, the timings may not be exactly what your board's
* chips need ... there may be several reasons you'd need to tweak timings
* in these routines, not just make to make it faster or slower to match a
* particular CPU clock rate.
*/
static inline u32
bitbang_txrx_be_cpha0(struct spi_device *spi,
unsigned nsecs, unsigned cpol,
u32 word, u8 bits)
{
/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
/* clock starts at inactive polarity */
for (word <<= (32 - bits); likely(bits); bits--) {
/* setup MSB (to slave) on trailing edge */
setmosi(spi, word & (1 << 31));
spidelay(nsecs); /* T(setup) */
setsck(spi, !cpol);
spidelay(nsecs);
/* sample MSB (from slave) on leading edge */
word <<= 1;
word |= getmiso(spi);
setsck(spi, cpol);
}
return word;
}
static inline u32
bitbang_txrx_be_cpha1(struct spi_device *spi,
unsigned nsecs, unsigned cpol,
u32 word, u8 bits)
{
/* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
/* clock starts at inactive polarity */
for (word <<= (32 - bits); likely(bits); bits--) {
/* setup MSB (to slave) on leading edge */
setsck(spi, !cpol);
setmosi(spi, word & (1 << 31));
spidelay(nsecs); /* T(setup) */
setsck(spi, cpol);
spidelay(nsecs);
/* sample MSB (from slave) on trailing edge */
word <<= 1;
word |= getmiso(spi);
}
return word;
}
#endif /* EXPAND_BITBANG_TXRX */
|
