diff options
author | Andy Gospodarek <andy@greyhouse.net> | 2010-06-02 08:40:18 +0000 |
---|---|---|
committer | David S. Miller <davem@davemloft.net> | 2010-06-05 02:23:17 -0700 |
commit | bb1d912323d5dd50e1079e389f4e964be14f0ae3 (patch) | |
tree | 7d20fff2e63bc6add251a56625110257d3ccc45f /Documentation/networking | |
parent | ebd8e4977a87cb81d93c62a9bff0102a9713722f (diff) | |
download | kernel_samsung_crespo-bb1d912323d5dd50e1079e389f4e964be14f0ae3.zip kernel_samsung_crespo-bb1d912323d5dd50e1079e389f4e964be14f0ae3.tar.gz kernel_samsung_crespo-bb1d912323d5dd50e1079e389f4e964be14f0ae3.tar.bz2 |
bonding: allow user-controlled output slave selection
v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.
This patch give the user the ability to control the output slave for
round-robin and active-backup bonding. Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode. Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.
Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag. This will allow reception of unicast traffic on
any of the backup interfaces.
This was tested with IPv4-based filters as well as VLAN-based filters
with good results.
More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'Documentation/networking')
-rw-r--r-- | Documentation/networking/bonding.txt | 84 |
1 files changed, 82 insertions, 2 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 61f516b..d091478 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -49,6 +49,7 @@ Table of Contents 3.3 Configuring Bonding Manually with Ifenslave 3.3.1 Configuring Multiple Bonds Manually 3.4 Configuring Bonding Manually via Sysfs +3.5 Overriding Configuration for Special Cases 4. Querying Bonding Configuration 4.1 Bonding Configuration @@ -1318,8 +1319,87 @@ echo 2000 > /sys/class/net/bond1/bonding/arp_interval echo +eth2 > /sys/class/net/bond1/bonding/slaves echo +eth3 > /sys/class/net/bond1/bonding/slaves - -4. Querying Bonding Configuration +3.5 Overriding Configuration for Special Cases +---------------------------------------------- +When using the bonding driver, the physical port which transmits a frame is +typically selected by the bonding driver, and is not relevant to the user or +system administrator. The output port is simply selected using the policies of +the selected bonding mode. On occasion however, it is helpful to direct certain +classes of traffic to certain physical interfaces on output to implement +slightly more complex policies. For example, to reach a web server over a +bonded interface in which eth0 connects to a private network, while eth1 +connects via a public network, it may be desirous to bias the bond to send said +traffic over eth0 first, using eth1 only as a fall back, while all other traffic +can safely be sent over either interface. Such configurations may be achieved +using the traffic control utilities inherent in linux. + +By default the bonding driver is multiqueue aware and 16 queues are created +when the driver initializes (see Documentation/networking/multiqueue.txt +for details). If more or less queues are desired the module parameter +tx_queues can be used to change this value. There is no sysfs parameter +available as the allocation is done at module init time. + +The output of the file /proc/net/bonding/bondX has changed so the output Queue +ID is now printed for each slave: + +Bonding Mode: fault-tolerance (active-backup) +Primary Slave: None +Currently Active Slave: eth0 +MII Status: up +MII Polling Interval (ms): 0 +Up Delay (ms): 0 +Down Delay (ms): 0 + +Slave Interface: eth0 +MII Status: up +Link Failure Count: 0 +Permanent HW addr: 00:1a:a0:12:8f:cb +Slave queue ID: 0 + +Slave Interface: eth1 +MII Status: up +Link Failure Count: 0 +Permanent HW addr: 00:1a:a0:12:8f:cc +Slave queue ID: 2 + +The queue_id for a slave can be set using the command: + +# echo "eth1:2" > /sys/class/net/bond0/bonding/queue_id + +Any interface that needs a queue_id set should set it with multiple calls +like the one above until proper priorities are set for all interfaces. On +distributions that allow configuration via initscripts, multiple 'queue_id' +arguments can be added to BONDING_OPTS to set all needed slave queues. + +These queue id's can be used in conjunction with the tc utility to configure +a multiqueue qdisc and filters to bias certain traffic to transmit on certain +slave devices. For instance, say we wanted, in the above configuration to +force all traffic bound to 192.168.1.100 to use eth1 in the bond as its output +device. The following commands would accomplish this: + +# tc qdisc add dev bond0 handle 1 root multiq + +# tc filter add dev bond0 protocol ip parent 1: prio 1 u32 match ip dst \ + 192.168.1.100 action skbedit queue_mapping 2 + +These commands tell the kernel to attach a multiqueue queue discipline to the +bond0 interface and filter traffic enqueued to it, such that packets with a dst +ip of 192.168.1.100 have their output queue mapping value overwritten to 2. +This value is then passed into the driver, causing the normal output path +selection policy to be overridden, selecting instead qid 2, which maps to eth1. + +Note that qid values begin at 1. Qid 0 is reserved to initiate to the driver +that normal output policy selection should take place. One benefit to simply +leaving the qid for a slave to 0 is the multiqueue awareness in the bonding +driver that is now present. This awareness allows tc filters to be placed on +slave devices as well as bond devices and the bonding driver will simply act as +a pass-through for selecting output queues on the slave device rather than +output port selection. + +This feature first appeared in bonding driver version 3.7.0 and support for +output slave selection was limited to round-robin and active-backup modes. + +4 Querying Bonding Configuration ================================= 4.1 Bonding Configuration |