[ARM] 5289/1: [AT91] Convert boards to use sam9_smc_configure()

Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.

The following boards have been modified:
 cam60 : NAND
 cap9adk : NAND, NOR
 qil-a9260 : NAND
 sam9-l9260 : NAND
 sam9260ek : NAND
 sam9261ek : DM9000 Ethernet, NAND
 sam9263 : NAND
 sam9g20ek : NAND
 sam9rlek : NAND
 usb-a9260 : NAND
 usb-a9263 .: NAND

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

11 files changed, 405 insertions, 59 deletions

diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index cdddca5..d3ba29c 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -39,7 +39,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -151,6 +153,32 @@ static struct atmel_nand_data __initdata cam60_nand_data = {
 	.partition_info	= nand_partitions,
 };
 
+static struct sam9_smc_config __initdata cam60_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init cam60_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &cam60_nand_smc_config);
+
+	at91_add_device_nand(&cam60_nand_data);
+}
+
 
 static void __init cam60_board_init(void)
 {
@@ -165,7 +193,7 @@ static void __init cam60_board_init(void)
 	at91_set_gpio_output(AT91_PIN_PB18, 1);
 	at91_add_device_usbh(&cam60_usbh_data);
 	/* NAND */
-	at91_add_device_nand(&cam60_nand_data);
+	cam60_add_device_nand();
 }
 
 MACHINE_START(CAM60, "KwikByte CAM60")
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c
index 201b893..43b37bc 100644
--- a/arch/arm/mach-at91/board-cap9adk.c
+++ b/arch/arm/mach-at91/board-cap9adk.c
@@ -47,6 +47,7 @@
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -195,6 +196,43 @@ static struct atmel_nand_data __initdata cap9adk_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata cap9adk_nand_smc_config = {
+	.ncs_read_setup		= 1,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 1,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 6,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 6,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 8,
+	.write_cycle		= 8,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 1,
+};
+
+static void __init cap9adk_add_device_nand(void)
+{
+	unsigned long csa;
+
+	csa = at91_sys_read(AT91_MATRIX_EBICSA);
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
+
+	/* setup bus-width (8 or 16) */
+	if (cap9adk_nand_data.bus_width_16)
+		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &cap9adk_nand_smc_config);
+
+	at91_add_device_nand(&cap9adk_nand_data);
+}
+
 
 /*
  * NOR flash
@@ -234,6 +272,24 @@ static struct platform_device cap9adk_nor_flash = {
 	.num_resources	= ARRAY_SIZE(nor_flash_resources),
 };
 
+static struct sam9_smc_config __initdata cap9adk_nor_smc_config = {
+	.ncs_read_setup		= 2,
+	.nrd_setup		= 4,
+	.ncs_write_setup	= 2,
+	.nwe_setup		= 4,
+
+	.ncs_read_pulse		= 10,
+	.nrd_pulse		= 8,
+	.ncs_write_pulse	= 10,
+	.nwe_pulse		= 8,
+
+	.read_cycle		= 16,
+	.write_cycle		= 16,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+	.tdf_cycles		= 1,
+};
+
 static __init void cap9adk_add_device_nor(void)
 {
 	unsigned long csa;
@@ -241,18 +297,8 @@ static __init void cap9adk_add_device_nor(void)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(0), AT91_SMC_NWESETUP_(4) | AT91_SMC_NCS_WRSETUP_(2)
-			| AT91_SMC_NRDSETUP_(4) | AT91_SMC_NCS_RDSETUP_(2));
-
-	at91_sys_write(AT91_SMC_PULSE(0), AT91_SMC_NWEPULSE_(8) | AT91_SMC_NCS_WRPULSE_(10)
-			| AT91_SMC_NRDPULSE_(8) | AT91_SMC_NCS_RDPULSE_(10));
-
-	at91_sys_write(AT91_SMC_CYCLE(0), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
-
-	at91_sys_write(AT91_SMC_MODE(0), AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE
-			| AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+	/* configure chip-select 0 (NOR) */
+	sam9_smc_configure(0, &cap9adk_nor_smc_config);
 
 	platform_device_register(&cap9adk_nor_flash);
 }
@@ -344,7 +390,7 @@ static void __init cap9adk_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&cap9adk_macb_data);
 	/* NAND */
-	at91_add_device_nand(&cap9adk_nand_data);
+	cap9adk_add_device_nand();
 	/* NOR Flash */
 	cap9adk_add_device_nor();
 	/* I2C */
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index cfb4571..4cff9a7 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -41,8 +41,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -147,13 +149,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 /*
  * MCI (SD/MMC)
  */
@@ -227,7 +250,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Ethernet */
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index 99bb4cc..b483469 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -38,7 +38,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -148,13 +150,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -178,7 +201,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index b49eb6e..93a0f8b 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -42,7 +42,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -195,6 +198,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -303,7 +338,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 4977409..d5266da 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -47,7 +47,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -76,7 +78,7 @@ static void __init ek_init_irq(void)
  * DM9000 ethernet device
  */
 #if defined(CONFIG_DM9000)
-static struct resource at91sam9261_dm9000_resource[] = {
+static struct resource dm9000_resource[] = {
 	[0] = {
 		.start	= AT91_CHIPSELECT_2,
 		.end	= AT91_CHIPSELECT_2 + 3,
@@ -98,27 +100,42 @@ static struct dm9000_plat_data dm9000_platdata = {
 	.flags		= DM9000_PLATF_16BITONLY,
 };
 
-static struct platform_device at91sam9261_dm9000_device = {
+static struct platform_device dm9000_device = {
 	.name		= "dm9000",
 	.id		= 0,
-	.num_resources	= ARRAY_SIZE(at91sam9261_dm9000_resource),
-	.resource	= at91sam9261_dm9000_resource,
+	.num_resources	= ARRAY_SIZE(dm9000_resource),
+	.resource	= dm9000_resource,
 	.dev		= {
 		.platform_data	= &dm9000_platdata,
 	}
 };
 
+/*
+ * SMC timings for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
+ */
+static struct sam9_smc_config __initdata dm9000_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 8,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 8,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 16,
+	.write_cycle		= 16,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+	.tdf_cycles		= 1,
+};
+
 static void __init ek_add_device_dm9000(void)
 {
-	/*
-	 * Configure Chip-Select 2 on SMC for the DM9000.
-	 * Note: These timings were calculated for MASTER_CLOCK = 100000000
-	 *  according to the DM9000 timings.
-	 */
-	at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-	at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
-	at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
-	at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+	/* Configure chip-select 2 (DM9000) */
+	sam9_smc_configure(2, &dm9000_smc_config);
 
 	/* Configure Reset signal as output */
 	at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -126,7 +143,7 @@ static void __init ek_add_device_dm9000(void)
 	/* Configure Interrupt pin as input, no pull-up */
 	at91_set_gpio_input(AT91_PIN_PC11, 0);
 
-	platform_device_register(&at91sam9261_dm9000_device);
+	platform_device_register(&dm9000_device);
 }
 #else
 static void __init ek_add_device_dm9000(void) {}
@@ -197,6 +214,39 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
 /*
  * ADS7846 Touchscreen
  */
@@ -525,7 +575,7 @@ static void __init ek_board_init(void)
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* DM9000 ethernet */
 	ek_add_device_dm9000();
 
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 8354015..57d5252 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -46,7 +46,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -203,6 +205,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * I2C devices
@@ -385,7 +419,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
 	/* LCD Controller */
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index b588ead..81439fe 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -37,7 +37,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -156,6 +158,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 7,
+	.write_cycle		= 7,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 3,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -195,7 +229,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index 2708518..9b937ee 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -29,8 +29,9 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
-#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -103,9 +104,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.partition_info	= nand_partitions,
-	.bus_width_16	= 0,
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * SPI devices
@@ -188,7 +214,7 @@ static void __init ek_board_init(void)
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-usb-a9260.c b/arch/arm/mach-at91/board-usb-a9260.c
index 7c35035..d13304c 100644
--- a/arch/arm/mach-at91/board-usb-a9260.c
+++ b/arch/arm/mach-at91/board-usb-a9260.c
@@ -41,8 +41,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -121,13 +123,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 /*
  * GPIO Buttons
  */
@@ -189,7 +212,7 @@ static void __init ek_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&ek_udc_data);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Ethernet */
diff --git a/arch/arm/mach-at91/board-usb-a9263.c b/arch/arm/mach-at91/board-usb-a9263.c
index 391b566..d96405b 100644
--- a/arch/arm/mach-at91/board-usb-a9263.c
+++ b/arch/arm/mach-at91/board-usb-a9263.c
@@ -40,8 +40,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -134,13 +136,35 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
 /*
  * GPIO Buttons
  */
@@ -206,7 +230,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Push Buttons */