[ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directories

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

29 files changed, 7191 insertions, 0 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
new file mode 100644
index 0000000..9f11db8
--- /dev/null
+++ b/arch/arm/mach-at91/Kconfig
@@ -0,0 +1,148 @@
+if ARCH_AT91
+
+menu "Atmel AT91 System-on-Chip"
+
+choice
+	prompt "Atmel AT91 Processor"
+
+config ARCH_AT91RM9200
+	bool "AT91RM9200"
+
+config ARCH_AT91SAM9260
+	bool "AT91SAM9260"
+
+config ARCH_AT91SAM9261
+	bool "AT91SAM9261"
+
+endchoice
+
+# ----------------------------------------------------------
+
+if ARCH_AT91RM9200
+
+comment "AT91RM9200 Board Type"
+
+config MACH_ONEARM
+	bool "Ajeco 1ARM Single Board Computer"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Ajeco's 1ARM Single Board Computer.
+	  <http://www.ajeco.fi/products.htm>
+
+config ARCH_AT91RM9200DK
+	bool "Atmel AT91RM9200-DK Development board"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Atmel's AT91RM9200-DK Development board.
+	  (Discontinued)
+
+config MACH_AT91RM9200EK
+	bool "Atmel AT91RM9200-EK Evaluation Kit"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit.
+	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507>
+
+config MACH_CSB337
+	bool "Cogent CSB337"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Cogent's CSB337 board.
+	  <http://www.cogcomp.com/csb_csb337.htm>
+
+config MACH_CSB637
+	bool "Cogent CSB637"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Cogent's CSB637 board.
+	  <http://www.cogcomp.com/csb_csb637.htm>
+
+config MACH_CARMEVA
+	bool "Conitec ARM&EVA"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Conitec's AT91RM9200-MCU-Module.
+	  <http://www.conitec.net/english/linuxboard.htm>
+
+config MACH_ATEB9200
+	bool "Embest ATEB9200"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Embest's ATEB9200 board.
+	  <http://www.embedinfo.com/english/product/ATEB9200.asp>
+
+config MACH_KB9200
+	bool "KwikByte KB920x"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using KwikByte's KB920x board.
+	  <http://kwikbyte.com/KB9202_description_new.htm>
+
+config MACH_KAFA
+	bool "Sperry-Sun KAFA board"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using Sperry-Sun's KAFA board.
+
+endif
+
+# ----------------------------------------------------------
+
+if ARCH_AT91SAM9260
+
+comment "AT91SAM9260 Board Type"
+
+config MACH_AT91SAM9260EK
+	bool "Atmel AT91SAM9260-EK Evaluation Kit"
+	depends on ARCH_AT91SAM9260
+	help
+	  Select this if you are using Atmel's AT91SAM9260-EK Evaluation Kit.
+	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
+
+endif
+
+# ----------------------------------------------------------
+
+if ARCH_AT91SAM9261
+
+comment "AT91SAM9261 Board Type"
+
+config MACH_AT91SAM9261EK
+	bool "Atmel AT91SAM9261-EK Evaluation Kit"
+	depends on ARCH_AT91SAM9261
+	help
+	  Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit.
+	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3820>
+
+endif
+
+# ----------------------------------------------------------
+
+comment "AT91 Board Options"
+
+config MTD_AT91_DATAFLASH_CARD
+	bool "Enable DataFlash Card support"
+	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK)
+	help
+	  Enable support for the DataFlash card.
+
+config MTD_NAND_AT91_BUSWIDTH_16
+	bool "Enable 16-bit data bus interface to NAND flash"
+	depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK)
+	help
+	  On AT91SAM926x boards both types of NAND flash can be present
+	  (8 and 16 bit data bus width).
+
+# ----------------------------------------------------------
+
+comment "AT91 Feature Selections"
+
+config AT91_PROGRAMMABLE_CLOCKS
+	bool "Programmable Clocks"
+	help
+	  Select this if you need to program one or more of the PCK0..PCK3
+	  programmable clock outputs.
+
+endmenu
+
+endif
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
new file mode 100644
index 0000000..cf77700
--- /dev/null
+++ b/arch/arm/mach-at91/Makefile
@@ -0,0 +1,49 @@
+#
+# Makefile for the linux kernel.
+#
+
+obj-y		:= clock.o irq.o gpio.o
+obj-m		:=
+obj-n		:=
+obj-		:=
+
+obj-$(CONFIG_PM)		+= pm.o
+
+# CPU-specific support
+obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
+
+# AT91RM9200 board-specific support
+obj-$(CONFIG_MACH_ONEARM)	+= board-1arm.o
+obj-$(CONFIG_ARCH_AT91RM9200DK)	+= board-dk.o
+obj-$(CONFIG_MACH_AT91RM9200EK)	+= board-ek.o
+obj-$(CONFIG_MACH_CSB337)	+= board-csb337.o
+obj-$(CONFIG_MACH_CSB637)	+= board-csb637.o
+obj-$(CONFIG_MACH_CARMEVA)	+= board-carmeva.o
+obj-$(CONFIG_MACH_KB9200)	+= board-kb9202.o
+obj-$(CONFIG_MACH_ATEB9200)	+= board-eb9200.o
+obj-$(CONFIG_MACH_KAFA)		+= board-kafa.o
+
+# AT91SAM9260 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
+
+# AT91SAM9261 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
+
+# LEDs support
+led-$(CONFIG_ARCH_AT91RM9200DK)	+= leds.o
+led-$(CONFIG_MACH_AT91RM9200EK)	+= leds.o
+led-$(CONFIG_MACH_CSB337)	+= leds.o
+led-$(CONFIG_MACH_CSB637)	+= leds.o
+led-$(CONFIG_MACH_KB9200)	+= leds.o
+led-$(CONFIG_MACH_KAFA)		+= leds.o
+obj-$(CONFIG_LEDS) += $(led-y)
+
+# VGA support
+#obj-$(CONFIG_FB_S1D13XXX)	+= ics1523.o
+
+
+ifeq ($(CONFIG_PM_DEBUG),y)
+CFLAGS_pm.o += -DDEBUG
+endif
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
new file mode 100644
index 0000000..e667dcc
--- /dev/null
+++ b/arch/arm/mach-at91/Makefile.boot
@@ -0,0 +1,9 @@
+# Note: the following conditions must always be true:
+#   ZRELADDR == virt_to_phys(TEXTADDR)
+#   PARAMS_PHYS must be within 4MB of ZRELADDR
+#   INITRD_PHYS must be in RAM
+
+   zreladdr-y	:= 0x20008000
+params_phys-y	:= 0x20000100
+initrd_phys-y	:= 0x20410000
+
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
new file mode 100644
index 0000000..870d4a4
--- /dev/null
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -0,0 +1,294 @@
+/*
+ * arch/arm/mach-at91/at91rm9200.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/arch/at91rm9200.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_st.h>
+
+#include "generic.h"
+#include "clock.h"
+
+static struct map_desc at91rm9200_io_desc[] __initdata = {
+	{
+		.virtual	= AT91_VA_BASE_SYS,
+		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_VA_BASE_EMAC,
+		.pfn		= __phys_to_pfn(AT91RM9200_BASE_EMAC),
+		.length		= SZ_16K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91RM9200_SRAM_SIZE,
+		.pfn		= __phys_to_pfn(AT91RM9200_SRAM_BASE),
+		.length		= AT91RM9200_SRAM_SIZE,
+		.type		= MT_DEVICE,
+	},
+};
+
+/* --------------------------------------------------------------------
+ *  Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+static struct clk udc_clk = {
+	.name		= "udc_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_UDP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ohci_clk = {
+	.name		= "ohci_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_UHP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ether_clk = {
+	.name		= "ether_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_EMAC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc_clk = {
+	.name		= "mci_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_MCI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi_clk = {
+	.name		= "twi_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TWI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+	.name		= "usart0_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_US0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart1_clk = {
+	.name		= "usart1_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_US1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart2_clk = {
+	.name		= "usart2_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_US2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart3_clk = {
+	.name		= "usart3_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_US3,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi_clk = {
+	.name		= "spi_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_SPI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioA_clk = {
+	.name		= "pioA_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_PIOA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+	.name		= "pioB_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_PIOB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioC_clk = {
+	.name		= "pioC_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_PIOC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioD_clk = {
+	.name		= "pioD_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_PIOD,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+
+static struct clk *periph_clocks[] __initdata = {
+	&pioA_clk,
+	&pioB_clk,
+	&pioC_clk,
+	&pioD_clk,
+	&usart0_clk,
+	&usart1_clk,
+	&usart2_clk,
+	&usart3_clk,
+	&mmc_clk,
+	&udc_clk,
+	&twi_clk,
+	&spi_clk,
+	// ssc 0 .. ssc2
+	// tc0 .. tc5
+	&ohci_clk,
+	&ether_clk,
+	// irq0 .. irq6
+};
+
+/*
+ * The four programmable clocks.
+ * You must configure pin multiplexing to bring these signals out.
+ */
+static struct clk pck0 = {
+	.name		= "pck0",
+	.pmc_mask	= AT91_PMC_PCK0,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 0,
+};
+static struct clk pck1 = {
+	.name		= "pck1",
+	.pmc_mask	= AT91_PMC_PCK1,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 1,
+};
+static struct clk pck2 = {
+	.name		= "pck2",
+	.pmc_mask	= AT91_PMC_PCK2,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 2,
+};
+static struct clk pck3 = {
+	.name		= "pck3",
+	.pmc_mask	= AT91_PMC_PCK3,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 3,
+};
+
+static void __init at91rm9200_register_clocks(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+		clk_register(periph_clocks[i]);
+
+	clk_register(&pck0);
+	clk_register(&pck1);
+	clk_register(&pck2);
+	clk_register(&pck3);
+}
+
+/* --------------------------------------------------------------------
+ *  GPIO
+ * -------------------------------------------------------------------- */
+
+static struct at91_gpio_bank at91rm9200_gpio[] = {
+	{
+		.id		= AT91RM9200_ID_PIOA,
+		.offset		= AT91_PIOA,
+		.clock		= &pioA_clk,
+	}, {
+		.id		= AT91RM9200_ID_PIOB,
+		.offset		= AT91_PIOB,
+		.clock		= &pioB_clk,
+	}, {
+		.id		= AT91RM9200_ID_PIOC,
+		.offset		= AT91_PIOC,
+		.clock		= &pioC_clk,
+	}, {
+		.id		= AT91RM9200_ID_PIOD,
+		.offset		= AT91_PIOD,
+		.clock		= &pioD_clk,
+	}
+};
+
+static void at91rm9200_reset(void)
+{
+	/*
+	 * Perform a hardware reset with the use of the Watchdog timer.
+	 */
+	at91_sys_write(AT91_ST_WDMR, AT91_ST_RSTEN | AT91_ST_EXTEN | 1);
+	at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
+}
+
+
+/* --------------------------------------------------------------------
+ *  AT91RM9200 processor initialization
+ * -------------------------------------------------------------------- */
+void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks)
+{
+	/* Map peripherals */
+	iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc));
+
+	at91_arch_reset = at91rm9200_reset;
+	at91_extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1)
+			| (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3)
+			| (1 << AT91RM9200_ID_IRQ4) | (1 << AT91RM9200_ID_IRQ5)
+			| (1 << AT91RM9200_ID_IRQ6);
+
+	/* Init clock subsystem */
+	at91_clock_init(main_clock);
+
+	/* Register the processor-specific clocks */
+	at91rm9200_register_clocks();
+
+	/* Initialize GPIO subsystem */
+	at91_gpio_init(at91rm9200_gpio, banks);
+}
+
+
+/* --------------------------------------------------------------------
+ *  Interrupt initialization
+ * -------------------------------------------------------------------- */
+
+/*
+ * The default interrupt priority levels (0 = lowest, 7 = highest).
+ */
+static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
+	7,	/* Advanced Interrupt Controller (FIQ) */
+	7,	/* System Peripherals */
+	0,	/* Parallel IO Controller A */
+	0,	/* Parallel IO Controller B */
+	0,	/* Parallel IO Controller C */
+	0,	/* Parallel IO Controller D */
+	6,	/* USART 0 */
+	6,	/* USART 1 */
+	6,	/* USART 2 */
+	6,	/* USART 3 */
+	0,	/* Multimedia Card Interface */
+	4,	/* USB Device Port */
+	0,	/* Two-Wire Interface */
+	6,	/* Serial Peripheral Interface */
+	5,	/* Serial Synchronous Controller 0 */
+	5,	/* Serial Synchronous Controller 1 */
+	5,	/* Serial Synchronous Controller 2 */
+	0,	/* Timer Counter 0 */
+	0,	/* Timer Counter 1 */
+	0,	/* Timer Counter 2 */
+	0,	/* Timer Counter 3 */
+	0,	/* Timer Counter 4 */
+	0,	/* Timer Counter 5 */
+	3,	/* USB Host port */
+	3,	/* Ethernet MAC */
+	0,	/* Advanced Interrupt Controller (IRQ0) */
+	0,	/* Advanced Interrupt Controller (IRQ1) */
+	0,	/* Advanced Interrupt Controller (IRQ2) */
+	0,	/* Advanced Interrupt Controller (IRQ3) */
+	0,	/* Advanced Interrupt Controller (IRQ4) */
+	0,	/* Advanced Interrupt Controller (IRQ5) */
+	0	/* Advanced Interrupt Controller (IRQ6) */
+};
+
+void __init at91rm9200_init_interrupts(unsigned int priority[NR_AIC_IRQS])
+{
+	if (!priority)
+		priority = at91rm9200_default_irq_priority;
+
+	/* Initialize the AIC interrupt controller */
+	at91_aic_init(priority);
+
+	/* Enable GPIO interrupts */
+	at91_gpio_irq_setup();
+}
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
new file mode 100644
index 0000000..a06498c
--- /dev/null
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -0,0 +1,875 @@
+/*
+ * arch/arm/mach-at91/at91rm9200_devices.c
+ *
+ *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *  Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/platform_device.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91rm9200.h>
+#include <asm/arch/at91rm9200_mc.h>
+
+#include "generic.h"
+
+#define SZ_512	0x00000200
+#define SZ_256	0x00000100
+#define SZ_16	0x00000010
+
+/* --------------------------------------------------------------------
+ *  USB Host
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static u64 ohci_dmamask = 0xffffffffUL;
+static struct at91_usbh_data usbh_data;
+
+static struct resource usbh_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_UHP_BASE,
+		.end	= AT91RM9200_UHP_BASE + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_UHP,
+		.end	= AT91RM9200_ID_UHP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_usbh_device = {
+	.name		= "at91_ohci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &ohci_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &usbh_data,
+	},
+	.resource	= usbh_resources,
+	.num_resources	= ARRAY_SIZE(usbh_resources),
+};
+
+void __init at91_add_device_usbh(struct at91_usbh_data *data)
+{
+	if (!data)
+		return;
+
+	usbh_data = *data;
+	platform_device_register(&at91rm9200_usbh_device);
+}
+#else
+void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  USB Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_USB_GADGET_AT91
+static struct at91_udc_data udc_data;
+
+static struct resource udc_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_UDP,
+		.end	= AT91RM9200_BASE_UDP + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_UDP,
+		.end	= AT91RM9200_ID_UDP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_udc_device = {
+	.name		= "at91_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &udc_data,
+	},
+	.resource	= udc_resources,
+	.num_resources	= ARRAY_SIZE(udc_resources),
+};
+
+void __init at91_add_device_udc(struct at91_udc_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->vbus_pin) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+	}
+	if (data->pullup_pin)
+		at91_set_gpio_output(data->pullup_pin, 0);
+
+	udc_data = *data;
+	platform_device_register(&at91rm9200_udc_device);
+}
+#else
+void __init at91_add_device_udc(struct at91_udc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Ethernet
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE)
+static u64 eth_dmamask = 0xffffffffUL;
+static struct at91_eth_data eth_data;
+
+static struct resource eth_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_EMAC,
+		.end	= AT91_VA_BASE_EMAC + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_EMAC,
+		.end	= AT91RM9200_ID_EMAC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_eth_device = {
+	.name		= "at91_ether",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &eth_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &eth_data,
+	},
+	.resource	= eth_resources,
+	.num_resources	= ARRAY_SIZE(eth_resources),
+};
+
+void __init at91_add_device_eth(struct at91_eth_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->phy_irq_pin) {
+		at91_set_gpio_input(data->phy_irq_pin, 0);
+		at91_set_deglitch(data->phy_irq_pin, 1);
+	}
+
+	/* Pins used for MII and RMII */
+	at91_set_A_periph(AT91_PIN_PA16, 0);	/* EMDIO */
+	at91_set_A_periph(AT91_PIN_PA15, 0);	/* EMDC */
+	at91_set_A_periph(AT91_PIN_PA14, 0);	/* ERXER */
+	at91_set_A_periph(AT91_PIN_PA13, 0);	/* ERX1 */
+	at91_set_A_periph(AT91_PIN_PA12, 0);	/* ERX0 */
+	at91_set_A_periph(AT91_PIN_PA11, 0);	/* ECRS_ECRSDV */
+	at91_set_A_periph(AT91_PIN_PA10, 0);	/* ETX1 */
+	at91_set_A_periph(AT91_PIN_PA9, 0);	/* ETX0 */
+	at91_set_A_periph(AT91_PIN_PA8, 0);	/* ETXEN */
+	at91_set_A_periph(AT91_PIN_PA7, 0);	/* ETXCK_EREFCK */
+
+	if (!data->is_rmii) {
+		at91_set_B_periph(AT91_PIN_PB19, 0);	/* ERXCK */
+		at91_set_B_periph(AT91_PIN_PB18, 0);	/* ECOL */
+		at91_set_B_periph(AT91_PIN_PB17, 0);	/* ERXDV */
+		at91_set_B_periph(AT91_PIN_PB16, 0);	/* ERX3 */
+		at91_set_B_periph(AT91_PIN_PB15, 0);	/* ERX2 */
+		at91_set_B_periph(AT91_PIN_PB14, 0);	/* ETXER */
+		at91_set_B_periph(AT91_PIN_PB13, 0);	/* ETX3 */
+		at91_set_B_periph(AT91_PIN_PB12, 0);	/* ETX2 */
+	}
+
+	eth_data = *data;
+	platform_device_register(&at91rm9200_eth_device);
+}
+#else
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Compact Flash / PCMCIA
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
+static struct at91_cf_data cf_data;
+
+#define CF_BASE		AT91_CHIPSELECT_4
+
+static struct resource cf_resources[] = {
+	[0] = {
+		.start	= CF_BASE,
+		/* ties up CS4, CS5 and CS6 */
+		.end	= CF_BASE + (0x30000000 - 1),
+		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+	},
+};
+
+static struct platform_device at91rm9200_cf_device = {
+	.name		= "at91_cf",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &cf_data,
+	},
+	.resource	= cf_resources,
+	.num_resources	= ARRAY_SIZE(cf_resources),
+};
+
+void __init at91_add_device_cf(struct at91_cf_data *data)
+{
+	unsigned int csa;
+
+	if (!data)
+		return;
+
+	data->chipselect = 4;		/* can only use EBI ChipSelect 4 */
+
+	/* CF takes over CS4, CS5, CS6 */
+	csa = at91_sys_read(AT91_EBI_CSA);
+	at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
+
+	/*
+	 * Static memory controller timing adjustments.
+	 * REVISIT:  these timings are in terms of MCK cycles, so
+	 * when MCK changes (cpufreq etc) so must these values...
+	 */
+	at91_sys_write(AT91_SMC_CSR(4),
+				  AT91_SMC_ACSS_STD
+				| AT91_SMC_DBW_16
+				| AT91_SMC_BAT
+				| AT91_SMC_WSEN
+				| AT91_SMC_NWS_(32)	/* wait states */
+				| AT91_SMC_RWSETUP_(6)	/* setup time */
+				| AT91_SMC_RWHOLD_(4)	/* hold time */
+	);
+
+	/* input/irq */
+	if (data->irq_pin) {
+		at91_set_gpio_input(data->irq_pin, 1);
+		at91_set_deglitch(data->irq_pin, 1);
+	}
+	at91_set_gpio_input(data->det_pin, 1);
+	at91_set_deglitch(data->det_pin, 1);
+
+	/* outputs, initially off */
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+	at91_set_gpio_output(data->rst_pin, 0);
+
+	/* force poweron defaults for these pins ... */
+	at91_set_A_periph(AT91_PIN_PC9, 0);	/* A25/CFRNW */
+	at91_set_A_periph(AT91_PIN_PC10, 0);	/* NCS4/CFCS */
+	at91_set_A_periph(AT91_PIN_PC11, 0);	/* NCS5/CFCE1 */
+	at91_set_A_periph(AT91_PIN_PC12, 0);	/* NCS6/CFCE2 */
+
+	/* nWAIT is _not_ a default setting */
+	at91_set_A_periph(AT91_PIN_PC6, 1);	/* nWAIT */
+
+	cf_data = *data;
+	platform_device_register(&at91rm9200_cf_device);
+}
+#else
+void __init at91_add_device_cf(struct at91_cf_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  MMC / SD
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+static u64 mmc_dmamask = 0xffffffffUL;
+static struct at91_mmc_data mmc_data;
+
+static struct resource mmc_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_MCI,
+		.end	= AT91RM9200_BASE_MCI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_MCI,
+		.end	= AT91RM9200_ID_MCI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_mmc_device = {
+	.name		= "at91_mci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &mmc_data,
+	},
+	.resource	= mmc_resources,
+	.num_resources	= ARRAY_SIZE(mmc_resources),
+};
+
+void __init at91_add_device_mmc(struct at91_mmc_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+	if (data->wp_pin)
+		at91_set_gpio_input(data->wp_pin, 1);
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA27, 0);
+
+	if (data->slot_b) {
+		/* CMD */
+		at91_set_B_periph(AT91_PIN_PA8, 1);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_B_periph(AT91_PIN_PA9, 1);
+		if (data->wire4) {
+			at91_set_B_periph(AT91_PIN_PA10, 1);
+			at91_set_B_periph(AT91_PIN_PA11, 1);
+			at91_set_B_periph(AT91_PIN_PA12, 1);
+		}
+	} else {
+		/* CMD */
+		at91_set_A_periph(AT91_PIN_PA28, 1);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_A_periph(AT91_PIN_PA29, 1);
+		if (data->wire4) {
+			at91_set_B_periph(AT91_PIN_PB3, 1);
+			at91_set_B_periph(AT91_PIN_PB4, 1);
+			at91_set_B_periph(AT91_PIN_PB5, 1);
+		}
+	}
+
+	mmc_data = *data;
+	platform_device_register(&at91rm9200_mmc_device);
+}
+#else
+void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+static struct at91_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	{
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_8M - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91rm9200_nand_device = {
+	.name		= "at91_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct at91_nand_data *data)
+{
+	unsigned int csa;
+
+	if (!data)
+		return;
+
+	/* enable the address range of CS3 */
+	csa = at91_sys_read(AT91_EBI_CSA);
+	at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
+
+	/* set the bus interface characteristics */
+	at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
+		| AT91_SMC_NWS_(5)
+		| AT91_SMC_TDF_(1)
+		| AT91_SMC_RWSETUP_(0)	/* tDS Data Set up Time 30 - ns */
+		| AT91_SMC_RWHOLD_(1)	/* tDH Data Hold Time 20 - ns */
+	);
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */
+	at91_set_A_periph(AT91_PIN_PC3, 0);		/* SMWE */
+
+	nand_data = *data;
+	platform_device_register(&at91rm9200_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct at91_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+
+static struct resource twi_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_TWI,
+		.end	= AT91RM9200_BASE_TWI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_TWI,
+		.end	= AT91RM9200_ID_TWI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_twi_device = {
+	.name		= "at91_i2c",
+	.id		= -1,
+	.resource	= twi_resources,
+	.num_resources	= ARRAY_SIZE(twi_resources),
+};
+
+void __init at91_add_device_i2c(void)
+{
+	/* pins used for TWI interface */
+	at91_set_A_periph(AT91_PIN_PA25, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PA25, 1);
+
+	at91_set_A_periph(AT91_PIN_PA26, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PA26, 1);
+
+	platform_device_register(&at91rm9200_twi_device);
+}
+#else
+void __init at91_add_device_i2c(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
+static u64 spi_dmamask = 0xffffffffUL;
+
+static struct resource spi_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_SPI,
+		.end	= AT91RM9200_BASE_SPI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_SPI,
+		.end	= AT91RM9200_ID_SPI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_spi_device = {
+	.name		= "at91_spi",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi_resources,
+	.num_resources	= ARRAY_SIZE(spi_resources),
+};
+
+static const unsigned spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+
+	at91_set_A_periph(AT91_PIN_PA0, 0);	/* MISO */
+	at91_set_A_periph(AT91_PIN_PA1, 0);	/* MOSI */
+	at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPCK */
+
+	/* Enable SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else
+			cs_pin = spi_standard_cs[devices[i].chip_select];
+
+#ifdef CONFIG_SPI_AT91_MANUAL_CS
+		at91_set_gpio_output(cs_pin, 1);
+#else
+		at91_set_A_periph(cs_pin, 0);
+#endif
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+	at91_clock_associate("spi_clk", &at91rm9200_spi_device.dev, "spi");
+	platform_device_register(&at91rm9200_spi_device);
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  RTC
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct platform_device at91rm9200_rtc_device = {
+	.name		= "at91_rtc",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_rtc(void)
+{
+	platform_device_register(&at91rm9200_rtc_device);
+}
+#else
+static void __init at91_add_device_rtc(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Watchdog
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91RM9200_WATCHDOG) || defined(CONFIG_AT91RM9200_WATCHDOG_MODULE)
+static struct platform_device at91rm9200_wdt_device = {
+	.name		= "at91_wdt",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_watchdog(void)
+{
+	platform_device_register(&at91rm9200_wdt_device);
+}
+#else
+static void __init at91_add_device_watchdog(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LEDs
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_LEDS)
+u8 at91_leds_cpu;
+u8 at91_leds_timer;
+
+void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+{
+	at91_leds_cpu	= cpu_led;
+	at91_leds_timer	= timer_led;
+}
+#else
+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_ATMEL)
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
+};
+
+static struct platform_device at91rm9200_dbgu_device = {
+	.name		= "atmel_usart",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &dbgu_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA30, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PA31, 1);		/* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US0,
+		.end	= AT91RM9200_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US0,
+		.end	= AT91RM9200_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart0_device = {
+	.name		= "atmel_usart",
+	.id		= 1,
+	.dev		= {
+				.platform_data	= &uart0_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA17, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PA18, 0);		/* RXD0 */
+	at91_set_A_periph(AT91_PIN_PA20, 0);		/* CTS0 */
+
+	/*
+	 * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
+	 *  We need to drive the pin manually.  Default is off (RTS is active low).
+	 */
+	at91_set_gpio_output(AT91_PIN_PA21, 1);
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US1,
+		.end	= AT91RM9200_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US1,
+		.end	= AT91RM9200_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart1_device = {
+	.name		= "atmel_usart",
+	.id		= 2,
+	.dev		= {
+				.platform_data	= &uart1_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB18, 0);		/* RI1 */
+	at91_set_A_periph(AT91_PIN_PB19, 0);		/* DTR1 */
+	at91_set_A_periph(AT91_PIN_PB20, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PB21, 0);		/* RXD1 */
+	at91_set_A_periph(AT91_PIN_PB23, 0);		/* DCD1 */
+	at91_set_A_periph(AT91_PIN_PB24, 0);		/* CTS1 */
+	at91_set_A_periph(AT91_PIN_PB25, 0);		/* DSR1 */
+	at91_set_A_periph(AT91_PIN_PB26, 0);		/* RTS1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US2,
+		.end	= AT91RM9200_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US2,
+		.end	= AT91RM9200_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart2_device = {
+	.name		= "atmel_usart",
+	.id		= 3,
+	.dev		= {
+				.platform_data	= &uart2_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart2_resources,
+	.num_resources	= ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA22, 0);		/* RXD2 */
+	at91_set_A_periph(AT91_PIN_PA23, 1);		/* TXD2 */
+}
+
+static struct resource uart3_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US3,
+		.end	= AT91RM9200_BASE_US3 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US3,
+		.end	= AT91RM9200_ID_US3,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart3_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart3_device = {
+	.name		= "atmel_usart",
+	.id		= 4,
+	.dev		= {
+				.platform_data	= &uart3_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart3_resources,
+	.num_resources	= ARRAY_SIZE(uart3_resources),
+};
+
+static inline void configure_usart3_pins(void)
+{
+	at91_set_B_periph(AT91_PIN_PA5, 1);		/* TXD3 */
+	at91_set_B_periph(AT91_PIN_PA6, 0);		/* RXD3 */
+}
+
+struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
+struct platform_device *atmel_default_console_device;	/* the serial console device */
+
+void __init at91_init_serial(struct at91_uart_config *config)
+{
+	int i;
+
+	/* Fill in list of supported UARTs */
+	for (i = 0; i < config->nr_tty; i++) {
+		switch (config->tty_map[i]) {
+			case 0:
+				configure_usart0_pins();
+				at91_uarts[i] = &at91rm9200_uart0_device;
+				at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
+				break;
+			case 1:
+				configure_usart1_pins();
+				at91_uarts[i] = &at91rm9200_uart1_device;
+				at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
+				break;
+			case 2:
+				configure_usart2_pins();
+				at91_uarts[i] = &at91rm9200_uart2_device;
+				at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
+				break;
+			case 3:
+				configure_usart3_pins();
+				at91_uarts[i] = &at91rm9200_uart3_device;
+				at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
+				break;
+			case 4:
+				configure_dbgu_pins();
+				at91_uarts[i] = &at91rm9200_dbgu_device;
+				at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart");
+				break;
+			default:
+				continue;
+		}
+		at91_uarts[i]->id = i;		/* update ID number to mapped ID */
+	}
+
+	/* Set serial console device */
+	if (config->console_tty < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[config->console_tty];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
+void __init at91_add_device_serial(void)
+{
+	int i;
+
+	for (i = 0; i < ATMEL_MAX_UART; i++) {
+		if (at91_uarts[i])
+			platform_device_register(at91_uarts[i]);
+	}
+}
+#else
+void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init at91_add_standard_devices(void)
+{
+	at91_add_device_rtc();
+	at91_add_device_watchdog();
+	return 0;
+}
+
+arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c
new file mode 100644
index 0000000..949199a
--- /dev/null
+++ b/arch/arm/mach-at91/at91rm9200_time.c
@@ -0,0 +1,146 @@
+/*
+ * linux/arch/arm/mach-at91/at91rm9200_time.c
+ *
+ *  Copyright (C) 2003 SAN People
+ *  Copyright (C) 2003 ATMEL
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/time.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/mach/time.h>
+
+#include <asm/arch/at91_st.h>
+
+static unsigned long last_crtr;
+
+/*
+ * The ST_CRTR is updated asynchronously to the master clock.  It is therefore
+ *  necessary to read it twice (with the same value) to ensure accuracy.
+ */
+static inline unsigned long read_CRTR(void) {
+	unsigned long x1, x2;
+
+	do {
+		x1 = at91_sys_read(AT91_ST_CRTR);
+		x2 = at91_sys_read(AT91_ST_CRTR);
+	} while (x1 != x2);
+
+	return x1;
+}
+
+/*
+ * Returns number of microseconds since last timer interrupt.  Note that interrupts
+ * will have been disabled by do_gettimeofday()
+ *  'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy.
+ *  'tick' is usecs per jiffy (linux/timex.h).
+ */
+static unsigned long at91rm9200_gettimeoffset(void)
+{
+	unsigned long elapsed;
+
+	elapsed = (read_CRTR() - last_crtr) & AT91_ST_ALMV;
+
+	return (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH;
+}
+
+/*
+ * IRQ handler for the timer.
+ */
+static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id)
+{
+	if (at91_sys_read(AT91_ST_SR) & AT91_ST_PITS) {	/* This is a shared interrupt */
+		write_seqlock(&xtime_lock);
+
+		while (((read_CRTR() - last_crtr) & AT91_ST_ALMV) >= LATCH) {
+			timer_tick();
+			last_crtr = (last_crtr + LATCH) & AT91_ST_ALMV;
+		}
+
+		write_sequnlock(&xtime_lock);
+
+		return IRQ_HANDLED;
+	}
+	else
+		return IRQ_NONE;		/* not handled */
+}
+
+static struct irqaction at91rm9200_timer_irq = {
+	.name		= "at91_tick",
+	.flags		= IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER,
+	.handler	= at91rm9200_timer_interrupt
+};
+
+void at91rm9200_timer_reset(void)
+{
+	last_crtr = 0;
+
+	/* Real time counter incremented every 30.51758 microseconds */
+	at91_sys_write(AT91_ST_RTMR, 1);
+
+	/* Set Period Interval timer */
+	at91_sys_write(AT91_ST_PIMR, LATCH);
+
+	/* Clear any pending interrupts */
+	(void) at91_sys_read(AT91_ST_SR);
+
+	/* Enable Period Interval Timer interrupt */
+	at91_sys_write(AT91_ST_IER, AT91_ST_PITS);
+}
+
+/*
+ * Set up timer interrupt.
+ */
+void __init at91rm9200_timer_init(void)
+{
+	/* Disable all timer interrupts */
+	at91_sys_write(AT91_ST_IDR, AT91_ST_PITS | AT91_ST_WDOVF | AT91_ST_RTTINC | AT91_ST_ALMS);
+	(void) at91_sys_read(AT91_ST_SR);	/* Clear any pending interrupts */
+
+	/* Make IRQs happen for the system timer */
+	setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq);
+
+	/* Change the kernel's 'tick' value to 10009 usec. (the default is 10000) */
+	tick_usec = (LATCH * 1000000) / CLOCK_TICK_RATE;
+
+	/* Initialize and enable the timer interrupt */
+	at91rm9200_timer_reset();
+}
+
+#ifdef CONFIG_PM
+static void at91rm9200_timer_suspend(void)
+{
+	/* disable Period Interval Timer interrupt */
+	at91_sys_write(AT91_ST_IDR, AT91_ST_PITS);
+}
+#else
+#define at91rm9200_timer_suspend	NULL
+#endif
+
+struct sys_timer at91rm9200_timer = {
+	.init		= at91rm9200_timer_init,
+	.offset		= at91rm9200_gettimeoffset,
+	.suspend	= at91rm9200_timer_suspend,
+	.resume		= at91rm9200_timer_reset,
+};
+
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
new file mode 100644
index 0000000..ffc4c09
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -0,0 +1,295 @@
+/*
+ * arch/arm/mach-at91/at91sam9260.c
+ *
+ *  Copyright (C) 2006 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/arch/at91sam9260.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+
+#include "generic.h"
+#include "clock.h"
+
+static struct map_desc at91sam9260_io_desc[] __initdata = {
+	{
+		.virtual	= AT91_VA_BASE_SYS,
+		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
+		.length		= SZ_16K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE,
+		.pfn		= __phys_to_pfn(AT91SAM9260_SRAM0_BASE),
+		.length		= AT91SAM9260_SRAM0_SIZE,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE - AT91SAM9260_SRAM1_SIZE,
+		.pfn		= __phys_to_pfn(AT91SAM9260_SRAM1_BASE),
+		.length		= AT91SAM9260_SRAM1_SIZE,
+		.type		= MT_DEVICE,
+	},
+};
+
+/* --------------------------------------------------------------------
+ *  Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+static struct clk pioA_clk = {
+	.name		= "pioA_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_PIOA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+	.name		= "pioB_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_PIOB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioC_clk = {
+	.name		= "pioC_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_PIOC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk adc_clk = {
+	.name		= "adc_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_ADC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+	.name		= "usart0_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_US0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart1_clk = {
+	.name		= "usart1_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_US1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart2_clk = {
+	.name		= "usart2_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_US2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc_clk = {
+	.name		= "mci_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_MCI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk udc_clk = {
+	.name		= "udc_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_UDP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi_clk = {
+	.name		= "twi_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TWI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi0_clk = {
+	.name		= "spi0_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_SPI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi1_clk = {
+	.name		= "spi1_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_SPI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ohci_clk = {
+	.name		= "ohci_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_UHP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ether_clk = {
+	.name		= "ether_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_EMAC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk isi_clk = {
+	.name		= "isi_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_ISI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart3_clk = {
+	.name		= "usart3_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_US3,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart4_clk = {
+	.name		= "usart4_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_US4,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart5_clk = {
+	.name		= "usart5_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_US5,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+
+static struct clk *periph_clocks[] __initdata = {
+	&pioA_clk,
+	&pioB_clk,
+	&pioC_clk,
+	&adc_clk,
+	&usart0_clk,
+	&usart1_clk,
+	&usart2_clk,
+	&mmc_clk,
+	&udc_clk,
+	&twi_clk,
+	&spi0_clk,
+	&spi1_clk,
+	// ssc
+	// tc0 .. tc2
+	&ohci_clk,
+	&ether_clk,
+	&isi_clk,
+	&usart3_clk,
+	&usart4_clk,
+	&usart5_clk,
+	// tc3 .. tc5
+	// irq0 .. irq2
+};
+
+/*
+ * The two programmable clocks.
+ * You must configure pin multiplexing to bring these signals out.
+ */
+static struct clk pck0 = {
+	.name		= "pck0",
+	.pmc_mask	= AT91_PMC_PCK0,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 0,
+};
+static struct clk pck1 = {
+	.name		= "pck1",
+	.pmc_mask	= AT91_PMC_PCK1,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 1,
+};
+
+static void __init at91sam9260_register_clocks(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+		clk_register(periph_clocks[i]);
+
+	clk_register(&pck0);
+	clk_register(&pck1);
+}
+
+/* --------------------------------------------------------------------
+ *  GPIO
+ * -------------------------------------------------------------------- */
+
+static struct at91_gpio_bank at91sam9260_gpio[] = {
+	{
+		.id		= AT91SAM9260_ID_PIOA,
+		.offset		= AT91_PIOA,
+		.clock		= &pioA_clk,
+	}, {
+		.id		= AT91SAM9260_ID_PIOB,
+		.offset		= AT91_PIOB,
+		.clock		= &pioB_clk,
+	}, {
+		.id		= AT91SAM9260_ID_PIOC,
+		.offset		= AT91_PIOC,
+		.clock		= &pioC_clk,
+	}
+};
+
+static void at91sam9260_reset(void)
+{
+	at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+}
+
+
+/* --------------------------------------------------------------------
+ *  AT91SAM9260 processor initialization
+ * -------------------------------------------------------------------- */
+
+void __init at91sam9260_initialize(unsigned long main_clock)
+{
+	/* Map peripherals */
+	iotable_init(at91sam9260_io_desc, ARRAY_SIZE(at91sam9260_io_desc));
+
+	at91_arch_reset = at91sam9260_reset;
+	at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
+			| (1 << AT91SAM9260_ID_IRQ2);
+
+	/* Init clock subsystem */
+	at91_clock_init(main_clock);
+
+	/* Register the processor-specific clocks */
+	at91sam9260_register_clocks();
+
+	/* Register GPIO subsystem */
+	at91_gpio_init(at91sam9260_gpio, 3);
+}
+
+/* --------------------------------------------------------------------
+ *  Interrupt initialization
+ * -------------------------------------------------------------------- */
+
+/*
+ * The default interrupt priority levels (0 = lowest, 7 = highest).
+ */
+static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
+	7,	/* Advanced Interrupt Controller */
+	7,	/* System Peripherals */
+	0,	/* Parallel IO Controller A */
+	0,	/* Parallel IO Controller B */
+	0,	/* Parallel IO Controller C */
+	0,	/* Analog-to-Digital Converter */
+	6,	/* USART 0 */
+	6,	/* USART 1 */
+	6,	/* USART 2 */
+	0,	/* Multimedia Card Interface */
+	4,	/* USB Device Port */
+	0,	/* Two-Wire Interface */
+	6,	/* Serial Peripheral Interface 0 */
+	6,	/* Serial Peripheral Interface 1 */
+	5,	/* Serial Synchronous Controller */
+	0,
+	0,
+	0,	/* Timer Counter 0 */
+	0,	/* Timer Counter 1 */
+	0,	/* Timer Counter 2 */
+	3,	/* USB Host port */
+	3,	/* Ethernet */
+	0,	/* Image Sensor Interface */
+	6,	/* USART 3 */
+	6,	/* USART 4 */
+	6,	/* USART 5 */
+	0,	/* Timer Counter 3 */
+	0,	/* Timer Counter 4 */
+	0,	/* Timer Counter 5 */
+	0,	/* Advanced Interrupt Controller */
+	0,	/* Advanced Interrupt Controller */
+	0,	/* Advanced Interrupt Controller */
+};
+
+void __init at91sam9260_init_interrupts(unsigned int priority[NR_AIC_IRQS])
+{
+	if (!priority)
+		priority = at91sam9260_default_irq_priority;
+
+	/* Initialize the AIC interrupt controller */
+	at91_aic_init(priority);
+
+	/* Enable GPIO interrupts */
+	at91_gpio_irq_setup();
+}
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
new file mode 100644
index 0000000..4adff70
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -0,0 +1,867 @@
+/*
+ * arch/arm/mach-at91/at91sam9260_devices.c
+ *
+ *  Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/platform_device.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam9260.h>
+#include <asm/arch/at91sam926x_mc.h>
+#include <asm/arch/at91sam9260_matrix.h>
+
+#include "generic.h"
+
+#define SZ_512	0x00000200
+#define SZ_256	0x00000100
+#define SZ_16	0x00000010
+
+/* --------------------------------------------------------------------
+ *  USB Host
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static u64 ohci_dmamask = 0xffffffffUL;
+static struct at91_usbh_data usbh_data;
+
+static struct resource usbh_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_UHP_BASE,
+		.end	= AT91SAM9260_UHP_BASE + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_UHP,
+		.end	= AT91SAM9260_ID_UHP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91_usbh_device = {
+	.name		= "at91_ohci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &ohci_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &usbh_data,
+	},
+	.resource	= usbh_resources,
+	.num_resources	= ARRAY_SIZE(usbh_resources),
+};
+
+void __init at91_add_device_usbh(struct at91_usbh_data *data)
+{
+	if (!data)
+		return;
+
+	usbh_data = *data;
+	platform_device_register(&at91_usbh_device);
+}
+#else
+void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  USB Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_USB_GADGET_AT91
+static struct at91_udc_data udc_data;
+
+static struct resource udc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_UDP,
+		.end	= AT91SAM9260_BASE_UDP + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_UDP,
+		.end	= AT91SAM9260_ID_UDP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91_udc_device = {
+	.name		= "at91_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &udc_data,
+	},
+	.resource	= udc_resources,
+	.num_resources	= ARRAY_SIZE(udc_resources),
+};
+
+void __init at91_add_device_udc(struct at91_udc_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->vbus_pin) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+	}
+
+	/* Pullup pin is handled internally by USB device peripheral */
+
+	udc_data = *data;
+	platform_device_register(&at91_udc_device);
+}
+#else
+void __init at91_add_device_udc(struct at91_udc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Ethernet
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
+static u64 eth_dmamask = 0xffffffffUL;
+static struct at91_eth_data eth_data;
+
+static struct resource eth_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_EMAC,
+		.end	= AT91SAM9260_BASE_EMAC + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_EMAC,
+		.end	= AT91SAM9260_ID_EMAC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9260_eth_device = {
+	.name		= "macb",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &eth_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &eth_data,
+	},
+	.resource	= eth_resources,
+	.num_resources	= ARRAY_SIZE(eth_resources),
+};
+
+void __init at91_add_device_eth(struct at91_eth_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->phy_irq_pin) {
+		at91_set_gpio_input(data->phy_irq_pin, 0);
+		at91_set_deglitch(data->phy_irq_pin, 1);
+	}
+
+	/* Pins used for MII and RMII */
+	at91_set_A_periph(AT91_PIN_PA19, 0);	/* ETXCK_EREFCK */
+	at91_set_A_periph(AT91_PIN_PA17, 0);	/* ERXDV */
+	at91_set_A_periph(AT91_PIN_PA14, 0);	/* ERX0 */
+	at91_set_A_periph(AT91_PIN_PA15, 0);	/* ERX1 */
+	at91_set_A_periph(AT91_PIN_PA18, 0);	/* ERXER */
+	at91_set_A_periph(AT91_PIN_PA16, 0);	/* ETXEN */
+	at91_set_A_periph(AT91_PIN_PA12, 0);	/* ETX0 */
+	at91_set_A_periph(AT91_PIN_PA13, 0);	/* ETX1 */
+	at91_set_A_periph(AT91_PIN_PA21, 0);	/* EMDIO */
+	at91_set_A_periph(AT91_PIN_PA20, 0);	/* EMDC */
+
+	if (!data->is_rmii) {
+		at91_set_B_periph(AT91_PIN_PA28, 0);	/* ECRS */
+		at91_set_B_periph(AT91_PIN_PA29, 0);	/* ECOL */
+		at91_set_B_periph(AT91_PIN_PA25, 0);	/* ERX2 */
+		at91_set_B_periph(AT91_PIN_PA26, 0);	/* ERX3 */
+		at91_set_B_periph(AT91_PIN_PA27, 0);	/* ERXCK */
+		at91_set_B_periph(AT91_PIN_PA23, 0);	/* ETX2 */
+		at91_set_B_periph(AT91_PIN_PA24, 0);	/* ETX3 */
+		at91_set_B_periph(AT91_PIN_PA22, 0);	/* ETXER */
+	}
+
+	eth_data = *data;
+	platform_device_register(&at91sam9260_eth_device);
+}
+#else
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  MMC / SD
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+static u64 mmc_dmamask = 0xffffffffUL;
+static struct at91_mmc_data mmc_data;
+
+static struct resource mmc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_MCI,
+		.end	= AT91SAM9260_BASE_MCI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_MCI,
+		.end	= AT91SAM9260_ID_MCI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9260_mmc_device = {
+	.name		= "at91_mci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &mmc_data,
+	},
+	.resource	= mmc_resources,
+	.num_resources	= ARRAY_SIZE(mmc_resources),
+};
+
+void __init at91_add_device_mmc(struct at91_mmc_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+	if (data->wp_pin)
+		at91_set_gpio_input(data->wp_pin, 1);
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA8, 0);
+
+	if (data->slot_b) {
+		/* CMD */
+		at91_set_B_periph(AT91_PIN_PA1, 1);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_B_periph(AT91_PIN_PA0, 1);
+		if (data->wire4) {
+			at91_set_B_periph(AT91_PIN_PA5, 1);
+			at91_set_B_periph(AT91_PIN_PA4, 1);
+			at91_set_B_periph(AT91_PIN_PA3, 1);
+		}
+	} else {
+		/* CMD */
+		at91_set_A_periph(AT91_PIN_PA7, 1);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_A_periph(AT91_PIN_PA6, 1);
+		if (data->wire4) {
+			at91_set_A_periph(AT91_PIN_PA9, 1);
+			at91_set_A_periph(AT91_PIN_PA10, 1);
+			at91_set_A_periph(AT91_PIN_PA11, 1);
+		}
+	}
+
+	mmc_data = *data;
+	platform_device_register(&at91sam9260_mmc_device);
+}
+#else
+void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+static struct at91_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	{
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_8M - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91sam9260_nand_device = {
+	.name		= "at91_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct at91_nand_data *data)
+{
+	unsigned long csa, mode;
+
+	if (!data)
+		return;
+
+	csa = at91_sys_read(AT91_MATRIX_EBICSA);
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC);
+
+	/* set the bus interface characteristics */
+	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0)
+			| AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+
+	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5)
+			| AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5));
+
+	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
+
+	if (data->bus_width_16)
+		mode = AT91_SMC_DBW_16;
+	else
+		mode = AT91_SMC_DBW_8;
+	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1));
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	nand_data = *data;
+	platform_device_register(&at91sam9260_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct at91_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+
+static struct resource twi_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_TWI,
+		.end	= AT91SAM9260_BASE_TWI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_TWI,
+		.end	= AT91SAM9260_ID_TWI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9260_twi_device = {
+	.name		= "at91_i2c",
+	.id		= -1,
+	.resource	= twi_resources,
+	.num_resources	= ARRAY_SIZE(twi_resources),
+};
+
+void __init at91_add_device_i2c(void)
+{
+	/* pins used for TWI interface */
+	at91_set_A_periph(AT91_PIN_PA23, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PA23, 1);
+
+	at91_set_A_periph(AT91_PIN_PA24, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PA24, 1);
+
+	platform_device_register(&at91sam9260_twi_device);
+}
+#else
+void __init at91_add_device_i2c(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+static u64 spi_dmamask = 0xffffffffUL;
+
+static struct resource spi0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_SPI0,
+		.end	= AT91SAM9260_BASE_SPI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_SPI0,
+		.end	= AT91SAM9260_ID_SPI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9260_spi0_device = {
+	.name		= "atmel_spi",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi0_resources,
+	.num_resources	= ARRAY_SIZE(spi0_resources),
+};
+
+static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PC11, AT91_PIN_PC16, AT91_PIN_PC17 };
+
+static struct resource spi1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_SPI1,
+		.end	= AT91SAM9260_BASE_SPI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_SPI1,
+		.end	= AT91SAM9260_ID_SPI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9260_spi1_device = {
+	.name		= "atmel_spi",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi1_resources,
+	.num_resources	= ARRAY_SIZE(spi1_resources),
+};
+
+static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PC5, AT91_PIN_PC4, AT91_PIN_PC3 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+	short enable_spi0 = 0;
+	short enable_spi1 = 0;
+
+	/* Choose SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else if (devices[i].bus_num == 0)
+			cs_pin = spi0_standard_cs[devices[i].chip_select];
+		else
+			cs_pin = spi1_standard_cs[devices[i].chip_select];
+
+		if (devices[i].bus_num == 0)
+			enable_spi0 = 1;
+		else
+			enable_spi1 = 1;
+
+		/* enable chip-select pin */
+		at91_set_gpio_output(cs_pin, 1);
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+
+	/* Configure SPI bus(es) */
+	if (enable_spi0) {
+		at91_set_A_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
+		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
+		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi0_clk", &at91sam9260_spi0_device.dev, "spi_clk");
+		platform_device_register(&at91sam9260_spi0_device);
+	}
+	if (enable_spi1) {
+		at91_set_A_periph(AT91_PIN_PB0, 0);	/* SPI1_MISO */
+		at91_set_A_periph(AT91_PIN_PB1, 0);	/* SPI1_MOSI */
+		at91_set_A_periph(AT91_PIN_PB2, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi1_clk", &at91sam9260_spi1_device.dev, "spi_clk");
+		platform_device_register(&at91sam9260_spi1_device);
+	}
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LEDs
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_LEDS)
+u8 at91_leds_cpu;
+u8 at91_leds_timer;
+
+void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+{
+	at91_leds_cpu	= cpu_led;
+	at91_leds_timer	= timer_led;
+}
+#else
+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+#if defined(CONFIG_SERIAL_ATMEL)
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
+};
+
+static struct platform_device at91sam9260_dbgu_device = {
+	.name		= "atmel_usart",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &dbgu_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB14, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PB15, 1);		/* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_US0,
+		.end	= AT91SAM9260_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_US0,
+		.end	= AT91SAM9260_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9260_uart0_device = {
+	.name		= "atmel_usart",
+	.id		= 1,
+	.dev		= {
+				.platform_data	= &uart0_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB4, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PB5, 0);		/* RXD0 */
+	at91_set_A_periph(AT91_PIN_PB26, 0);		/* RTS0 */
+	at91_set_A_periph(AT91_PIN_PB27, 0);		/* CTS0 */
+	at91_set_A_periph(AT91_PIN_PB24, 0);		/* DTR0 */
+	at91_set_A_periph(AT91_PIN_PB22, 0);		/* DSR0 */
+	at91_set_A_periph(AT91_PIN_PB23, 0);		/* DCD0 */
+	at91_set_A_periph(AT91_PIN_PB25, 0);		/* RI0 */
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_US1,
+		.end	= AT91SAM9260_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_US1,
+		.end	= AT91SAM9260_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9260_uart1_device = {
+	.name		= "atmel_usart",
+	.id		= 2,
+	.dev		= {
+				.platform_data	= &uart1_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB6, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PB7, 0);		/* RXD1 */
+	at91_set_A_periph(AT91_PIN_PB28, 0);		/* RTS1 */
+	at91_set_A_periph(AT91_PIN_PB29, 0);		/* CTS1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_US2,
+		.end	= AT91SAM9260_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_US2,
+		.end	= AT91SAM9260_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9260_uart2_device = {
+	.name		= "atmel_usart",
+	.id		= 3,
+	.dev		= {
+				.platform_data	= &uart2_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart2_resources,
+	.num_resources	= ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB8, 1);		/* TXD2 */
+	at91_set_A_periph(AT91_PIN_PB9, 0);		/* RXD2 */
+}
+
+static struct resource uart3_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_US3,
+		.end	= AT91SAM9260_BASE_US3 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_US3,
+		.end	= AT91SAM9260_ID_US3,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart3_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9260_uart3_device = {
+	.name		= "atmel_usart",
+	.id		= 4,
+	.dev		= {
+				.platform_data	= &uart3_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart3_resources,
+	.num_resources	= ARRAY_SIZE(uart3_resources),
+};
+
+static inline void configure_usart3_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB10, 1);		/* TXD3 */
+	at91_set_A_periph(AT91_PIN_PB11, 0);		/* RXD3 */
+}
+
+static struct resource uart4_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_US4,
+		.end	= AT91SAM9260_BASE_US4 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_US4,
+		.end	= AT91SAM9260_ID_US4,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart4_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9260_uart4_device = {
+	.name		= "atmel_usart",
+	.id		= 5,
+	.dev		= {
+				.platform_data	= &uart4_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart4_resources,
+	.num_resources	= ARRAY_SIZE(uart4_resources),
+};
+
+static inline void configure_usart4_pins(void)
+{
+	at91_set_B_periph(AT91_PIN_PA31, 1);		/* TXD4 */
+	at91_set_B_periph(AT91_PIN_PA30, 0);		/* RXD4 */
+}
+
+static struct resource uart5_resources[] = {
+	[0] = {
+		.start	= AT91SAM9260_BASE_US5,
+		.end	= AT91SAM9260_BASE_US5 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9260_ID_US5,
+		.end	= AT91SAM9260_ID_US5,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart5_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9260_uart5_device = {
+	.name		= "atmel_usart",
+	.id		= 6,
+	.dev		= {
+				.platform_data	= &uart5_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart5_resources,
+	.num_resources	= ARRAY_SIZE(uart5_resources),
+};
+
+static inline void configure_usart5_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB12, 1);		/* TXD5 */
+	at91_set_A_periph(AT91_PIN_PB13, 0);		/* RXD5 */
+}
+
+struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
+struct platform_device *atmel_default_console_device;	/* the serial console device */
+
+void __init at91_init_serial(struct at91_uart_config *config)
+{
+	int i;
+
+	/* Fill in list of supported UARTs */
+	for (i = 0; i < config->nr_tty; i++) {
+		switch (config->tty_map[i]) {
+			case 0:
+				configure_usart0_pins();
+				at91_uarts[i] = &at91sam9260_uart0_device;
+				at91_clock_associate("usart0_clk", &at91sam9260_uart0_device.dev, "usart");
+				break;
+			case 1:
+				configure_usart1_pins();
+				at91_uarts[i] = &at91sam9260_uart1_device;
+				at91_clock_associate("usart1_clk", &at91sam9260_uart1_device.dev, "usart");
+				break;
+			case 2:
+				configure_usart2_pins();
+				at91_uarts[i] = &at91sam9260_uart2_device;
+				at91_clock_associate("usart2_clk", &at91sam9260_uart2_device.dev, "usart");
+				break;
+			case 3:
+				configure_usart3_pins();
+				at91_uarts[i] = &at91sam9260_uart3_device;
+				at91_clock_associate("usart3_clk", &at91sam9260_uart3_device.dev, "usart");
+				break;
+			case 4:
+				configure_usart4_pins();
+				at91_uarts[i] = &at91sam9260_uart4_device;
+				at91_clock_associate("usart4_clk", &at91sam9260_uart4_device.dev, "usart");
+				break;
+			case 5:
+				configure_usart5_pins();
+				at91_uarts[i] = &at91sam9260_uart5_device;
+				at91_clock_associate("usart5_clk", &at91sam9260_uart5_device.dev, "usart");
+				break;
+			case 6:
+				configure_dbgu_pins();
+				at91_uarts[i] = &at91sam9260_dbgu_device;
+				at91_clock_associate("mck", &at91sam9260_dbgu_device.dev, "usart");
+				break;
+			default:
+				continue;
+		}
+		at91_uarts[i]->id = i;		/* update ID number to mapped ID */
+	}
+
+	/* Set serial console device */
+	if (config->console_tty < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[config->console_tty];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
+void __init at91_add_device_serial(void)
+{
+	int i;
+
+	for (i = 0; i < ATMEL_MAX_UART; i++) {
+		if (at91_uarts[i])
+			platform_device_register(at91_uarts[i]);
+	}
+}
+#else
+void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init at91_add_standard_devices(void)
+{
+	return 0;
+}
+
+arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
new file mode 100644
index 0000000..47e02ff
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -0,0 +1,290 @@
+/*
+ * arch/arm/mach-at91/at91sam9261.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/arch/at91sam9261.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+
+#include "generic.h"
+#include "clock.h"
+
+static struct map_desc at91sam9261_io_desc[] __initdata = {
+	{
+		.virtual	= AT91_VA_BASE_SYS,
+		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
+		.length		= SZ_16K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9261_SRAM_SIZE,
+		.pfn		= __phys_to_pfn(AT91SAM9261_SRAM_BASE),
+		.length		= AT91SAM9261_SRAM_SIZE,
+		.type		= MT_DEVICE,
+	},
+};
+
+/* --------------------------------------------------------------------
+ *  Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+static struct clk pioA_clk = {
+	.name		= "pioA_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_PIOA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+	.name		= "pioB_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_PIOB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioC_clk = {
+	.name		= "pioC_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_PIOC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+	.name		= "usart0_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_US0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart1_clk = {
+	.name		= "usart1_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_US1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart2_clk = {
+	.name		= "usart2_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_US2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc_clk = {
+	.name		= "mci_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_MCI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk udc_clk = {
+	.name		= "udc_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_UDP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi_clk = {
+	.name		= "twi_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_TWI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi0_clk = {
+	.name		= "spi0_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_SPI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi1_clk = {
+	.name		= "spi1_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_SPI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ohci_clk = {
+	.name		= "ohci_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_UHP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk lcdc_clk = {
+	.name		= "lcdc_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_LCDC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+
+static struct clk *periph_clocks[] __initdata = {
+	&pioA_clk,
+	&pioB_clk,
+	&pioC_clk,
+	&usart0_clk,
+	&usart1_clk,
+	&usart2_clk,
+	&mmc_clk,
+	&udc_clk,
+	&twi_clk,
+	&spi0_clk,
+	&spi1_clk,
+	// ssc 0 .. ssc2
+	// tc0 .. tc2
+	&ohci_clk,
+	&lcdc_clk,
+	// irq0 .. irq2
+};
+
+/*
+ * The four programmable clocks.
+ * You must configure pin multiplexing to bring these signals out.
+ */
+static struct clk pck0 = {
+	.name		= "pck0",
+	.pmc_mask	= AT91_PMC_PCK0,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 0,
+};
+static struct clk pck1 = {
+	.name		= "pck1",
+	.pmc_mask	= AT91_PMC_PCK1,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 1,
+};
+static struct clk pck2 = {
+	.name		= "pck2",
+	.pmc_mask	= AT91_PMC_PCK2,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 2,
+};
+static struct clk pck3 = {
+	.name		= "pck3",
+	.pmc_mask	= AT91_PMC_PCK3,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 3,
+};
+
+/* HClocks */
+static struct clk hck0 = {
+	.name		= "hck0",
+	.pmc_mask	= AT91_PMC_HCK0,
+	.type		= CLK_TYPE_SYSTEM,
+	.id		= 0,
+};
+static struct clk hck1 = {
+	.name		= "hck1",
+	.pmc_mask	= AT91_PMC_HCK1,
+	.type		= CLK_TYPE_SYSTEM,
+	.id		= 1,
+};
+
+static void __init at91sam9261_register_clocks(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+		clk_register(periph_clocks[i]);
+
+	clk_register(&pck0);
+	clk_register(&pck1);
+	clk_register(&pck2);
+	clk_register(&pck3);
+
+	clk_register(&hck0);
+	clk_register(&hck1);
+}
+
+/* --------------------------------------------------------------------
+ *  GPIO
+ * -------------------------------------------------------------------- */
+
+static struct at91_gpio_bank at91sam9261_gpio[] = {
+	{
+		.id		= AT91SAM9261_ID_PIOA,
+		.offset		= AT91_PIOA,
+		.clock		= &pioA_clk,
+	}, {
+		.id		= AT91SAM9261_ID_PIOB,
+		.offset		= AT91_PIOB,
+		.clock		= &pioB_clk,
+	}, {
+		.id		= AT91SAM9261_ID_PIOC,
+		.offset		= AT91_PIOC,
+		.clock		= &pioC_clk,
+	}
+};
+
+static void at91sam9261_reset(void)
+{
+	at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+}
+
+
+/* --------------------------------------------------------------------
+ *  AT91SAM9261 processor initialization
+ * -------------------------------------------------------------------- */
+
+void __init at91sam9261_initialize(unsigned long main_clock)
+{
+	/* Map peripherals */
+	iotable_init(at91sam9261_io_desc, ARRAY_SIZE(at91sam9261_io_desc));
+
+	at91_arch_reset = at91sam9261_reset;
+	at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
+			| (1 << AT91SAM9261_ID_IRQ2);
+
+	/* Init clock subsystem */
+	at91_clock_init(main_clock);
+
+	/* Register the processor-specific clocks */
+	at91sam9261_register_clocks();
+
+	/* Register GPIO subsystem */
+	at91_gpio_init(at91sam9261_gpio, 3);
+}
+
+/* --------------------------------------------------------------------
+ *  Interrupt initialization
+ * -------------------------------------------------------------------- */
+
+/*
+ * The default interrupt priority levels (0 = lowest, 7 = highest).
+ */
+static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
+	7,	/* Advanced Interrupt Controller */
+	7,	/* System Peripherals */
+	0,	/* Parallel IO Controller A */
+	0,	/* Parallel IO Controller B */
+	0,	/* Parallel IO Controller C */
+	0,
+	6,	/* USART 0 */
+	6,	/* USART 1 */
+	6,	/* USART 2 */
+	0,	/* Multimedia Card Interface */
+	4,	/* USB Device Port */
+	0,	/* Two-Wire Interface */
+	6,	/* Serial Peripheral Interface 0 */
+	6,	/* Serial Peripheral Interface 1 */
+	5,	/* Serial Synchronous Controller 0 */
+	5,	/* Serial Synchronous Controller 1 */
+	5,	/* Serial Synchronous Controller 2 */
+	0,	/* Timer Counter 0 */
+	0,	/* Timer Counter 1 */
+	0,	/* Timer Counter 2 */
+	3,	/* USB Host port */
+	3,	/* LCD Controller */
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,	/* Advanced Interrupt Controller */
+	0,	/* Advanced Interrupt Controller */
+	0,	/* Advanced Interrupt Controller */
+};
+
+void __init at91sam9261_init_interrupts(unsigned int priority[NR_AIC_IRQS])
+{
+	if (!priority)
+		priority = at91sam9261_default_irq_priority;
+
+	/* Initialize the AIC interrupt controller */
+	at91_aic_init(priority);
+
+	/* Enable GPIO interrupts */
+	at91_gpio_irq_setup();
+}
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
new file mode 100644
index 0000000..3249de0
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -0,0 +1,741 @@
+/*
+ * arch/arm/mach-at91/at91sam9261_devices.c
+ *
+ *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *  Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/platform_device.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam9261.h>
+#include <asm/arch/at91sam9261_matrix.h>
+#include <asm/arch/at91sam926x_mc.h>
+
+#include "generic.h"
+
+#define SZ_512	0x00000200
+#define SZ_256	0x00000100
+#define SZ_16	0x00000010
+
+/* --------------------------------------------------------------------
+ *  USB Host
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static u64 ohci_dmamask = 0xffffffffUL;
+static struct at91_usbh_data usbh_data;
+
+static struct resource usbh_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_UHP_BASE,
+		.end	= AT91SAM9261_UHP_BASE + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_UHP,
+		.end	= AT91SAM9261_ID_UHP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9261_usbh_device = {
+	.name		= "at91_ohci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &ohci_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &usbh_data,
+	},
+	.resource	= usbh_resources,
+	.num_resources	= ARRAY_SIZE(usbh_resources),
+};
+
+void __init at91_add_device_usbh(struct at91_usbh_data *data)
+{
+	if (!data)
+		return;
+
+	usbh_data = *data;
+	platform_device_register(&at91sam9261_usbh_device);
+}
+#else
+void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  USB Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_USB_GADGET_AT91
+static struct at91_udc_data udc_data;
+
+static struct resource udc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_UDP,
+		.end	= AT91SAM9261_BASE_UDP + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_UDP,
+		.end	= AT91SAM9261_ID_UDP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9261_udc_device = {
+	.name		= "at91_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &udc_data,
+	},
+	.resource	= udc_resources,
+	.num_resources	= ARRAY_SIZE(udc_resources),
+};
+
+void __init at91_add_device_udc(struct at91_udc_data *data)
+{
+	unsigned long x;
+
+	if (!data)
+		return;
+
+	if (data->vbus_pin) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+	}
+
+	/* Pullup pin is handled internally */
+	x = at91_sys_read(AT91_MATRIX_USBPUCR);
+	at91_sys_write(AT91_MATRIX_USBPUCR, x | AT91_MATRIX_USBPUCR_PUON);
+
+	udc_data = *data;
+	platform_device_register(&at91sam9261_udc_device);
+}
+#else
+void __init at91_add_device_udc(struct at91_udc_data *data) {}
+#endif
+
+/* --------------------------------------------------------------------
+ *  MMC / SD
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+static u64 mmc_dmamask = 0xffffffffUL;
+static struct at91_mmc_data mmc_data;
+
+static struct resource mmc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_MCI,
+		.end	= AT91SAM9261_BASE_MCI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_MCI,
+		.end	= AT91SAM9261_ID_MCI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9261_mmc_device = {
+	.name		= "at91_mci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &mmc_data,
+	},
+	.resource	= mmc_resources,
+	.num_resources	= ARRAY_SIZE(mmc_resources),
+};
+
+void __init at91_add_device_mmc(struct at91_mmc_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+	if (data->wp_pin)
+		at91_set_gpio_input(data->wp_pin, 1);
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+
+	/* CLK */
+	at91_set_B_periph(AT91_PIN_PA2, 0);
+
+	/* CMD */
+	at91_set_B_periph(AT91_PIN_PA1, 1);
+
+	/* DAT0, maybe DAT1..DAT3 */
+	at91_set_B_periph(AT91_PIN_PA0, 1);
+	if (data->wire4) {
+		at91_set_B_periph(AT91_PIN_PA4, 1);
+		at91_set_B_periph(AT91_PIN_PA5, 1);
+		at91_set_B_periph(AT91_PIN_PA6, 1);
+	}
+
+	mmc_data = *data;
+	platform_device_register(&at91sam9261_mmc_device);
+}
+#else
+void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+static struct at91_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	{
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91_nand_device = {
+	.name		= "at91_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct at91_nand_data *data)
+{
+	unsigned long csa, mode;
+
+	if (!data)
+		return;
+
+	csa = at91_sys_read(AT91_MATRIX_EBICSA);
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC);
+
+	/* set the bus interface characteristics */
+	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0)
+			| AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+
+	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5)
+			| AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5));
+
+	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
+
+	if (data->bus_width_16)
+		mode = AT91_SMC_DBW_16;
+	else
+		mode = AT91_SMC_DBW_8;
+	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1));
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	at91_set_A_periph(AT91_PIN_PC0, 0);		/* NANDOE */
+	at91_set_A_periph(AT91_PIN_PC1, 0);		/* NANDWE */
+
+	nand_data = *data;
+	platform_device_register(&at91_nand_device);
+}
+
+#else
+void __init at91_add_device_nand(struct at91_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+
+static struct resource twi_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_TWI,
+		.end	= AT91SAM9261_BASE_TWI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_TWI,
+		.end	= AT91SAM9261_ID_TWI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9261_twi_device = {
+	.name		= "at91_i2c",
+	.id		= -1,
+	.resource	= twi_resources,
+	.num_resources	= ARRAY_SIZE(twi_resources),
+};
+
+void __init at91_add_device_i2c(void)
+{
+	/* pins used for TWI interface */
+	at91_set_A_periph(AT91_PIN_PA7, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PA7, 1);
+
+	at91_set_A_periph(AT91_PIN_PA8, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PA8, 1);
+
+	platform_device_register(&at91sam9261_twi_device);
+}
+#else
+void __init at91_add_device_i2c(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+static u64 spi_dmamask = 0xffffffffUL;
+
+static struct resource spi0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_SPI0,
+		.end	= AT91SAM9261_BASE_SPI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_SPI0,
+		.end	= AT91SAM9261_ID_SPI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9261_spi0_device = {
+	.name		= "atmel_spi",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi0_resources,
+	.num_resources	= ARRAY_SIZE(spi0_resources),
+};
+
+static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
+
+static struct resource spi1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_SPI1,
+		.end	= AT91SAM9261_BASE_SPI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_SPI1,
+		.end	= AT91SAM9261_ID_SPI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9261_spi1_device = {
+	.name		= "atmel_spi",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi1_resources,
+	.num_resources	= ARRAY_SIZE(spi1_resources),
+};
+
+static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB28, AT91_PIN_PA24, AT91_PIN_PA25, AT91_PIN_PA26 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+	short enable_spi0 = 0;
+	short enable_spi1 = 0;
+
+	/* Choose SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else if (devices[i].bus_num == 0)
+			cs_pin = spi0_standard_cs[devices[i].chip_select];
+		else
+			cs_pin = spi1_standard_cs[devices[i].chip_select];
+
+		if (devices[i].bus_num == 0)
+			enable_spi0 = 1;
+		else
+			enable_spi1 = 1;
+
+		/* enable chip-select pin */
+		at91_set_gpio_output(cs_pin, 1);
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+
+	/* Configure SPI bus(es) */
+	if (enable_spi0) {
+		at91_set_A_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
+		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
+		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
+
+		at91_clock_associate("spi0_clk", &at91sam9261_spi0_device.dev, "spi_clk");
+		platform_device_register(&at91sam9261_spi0_device);
+	}
+	if (enable_spi1) {
+		at91_set_A_periph(AT91_PIN_PB30, 0);	/* SPI1_MISO */
+		at91_set_A_periph(AT91_PIN_PB31, 0);	/* SPI1_MOSI */
+		at91_set_A_periph(AT91_PIN_PB29, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi1_clk", &at91sam9261_spi1_device.dev, "spi_clk");
+		platform_device_register(&at91sam9261_spi1_device);
+	}
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LCD Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_FB_AT91) || defined(CONFIG_FB_AT91_MODULE)
+static u64 lcdc_dmamask = 0xffffffffUL;
+static struct at91fb_info lcdc_data;
+
+static struct resource lcdc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_LCDC_BASE,
+		.end	= AT91SAM9261_LCDC_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_LCDC,
+		.end	= AT91SAM9261_ID_LCDC,
+		.flags	= IORESOURCE_IRQ,
+	},
+#if defined(CONFIG_FB_INTSRAM)
+	[2] = {
+		.start	= AT91SAM9261_SRAM_BASE,
+		.end	= AT91SAM9261_SRAM_BASE + AT91SAM9261_SRAM_SIZE - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+#endif
+};
+
+static struct platform_device at91_lcdc_device = {
+	.name		= "at91-fb",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &lcdc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &lcdc_data,
+	},
+	.resource	= lcdc_resources,
+	.num_resources	= ARRAY_SIZE(lcdc_resources),
+};
+
+void __init at91_add_device_lcdc(struct at91fb_info *data)
+{
+	if (!data) {
+		return;
+	}
+
+	at91_set_A_periph(AT91_PIN_PB1, 0);	/* LCDHSYNC */
+	at91_set_A_periph(AT91_PIN_PB2, 0);	/* LCDDOTCK */
+	at91_set_A_periph(AT91_PIN_PB3, 0);	/* LCDDEN */
+	at91_set_A_periph(AT91_PIN_PB4, 0);	/* LCDCC */
+	at91_set_A_periph(AT91_PIN_PB7, 0);	/* LCDD2 */
+	at91_set_A_periph(AT91_PIN_PB8, 0);	/* LCDD3 */
+	at91_set_A_periph(AT91_PIN_PB9, 0);	/* LCDD4 */
+	at91_set_A_periph(AT91_PIN_PB10, 0);	/* LCDD5 */
+	at91_set_A_periph(AT91_PIN_PB11, 0);	/* LCDD6 */
+	at91_set_A_periph(AT91_PIN_PB12, 0);	/* LCDD7 */
+	at91_set_A_periph(AT91_PIN_PB15, 0);	/* LCDD10 */
+	at91_set_A_periph(AT91_PIN_PB16, 0);	/* LCDD11 */
+	at91_set_A_periph(AT91_PIN_PB17, 0);	/* LCDD12 */
+	at91_set_A_periph(AT91_PIN_PB18, 0);	/* LCDD13 */
+	at91_set_A_periph(AT91_PIN_PB19, 0);	/* LCDD14 */
+	at91_set_A_periph(AT91_PIN_PB20, 0);	/* LCDD15 */
+	at91_set_B_periph(AT91_PIN_PB23, 0);	/* LCDD18 */
+	at91_set_B_periph(AT91_PIN_PB24, 0);	/* LCDD19 */
+	at91_set_B_periph(AT91_PIN_PB25, 0);	/* LCDD20 */
+	at91_set_B_periph(AT91_PIN_PB26, 0);	/* LCDD21 */
+	at91_set_B_periph(AT91_PIN_PB27, 0);	/* LCDD22 */
+	at91_set_B_periph(AT91_PIN_PB28, 0);	/* LCDD23 */
+
+	lcdc_data = *data;
+	platform_device_register(&at91_lcdc_device);
+}
+#else
+void __init at91_add_device_lcdc(struct at91fb_info *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LEDs
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_LEDS)
+u8 at91_leds_cpu;
+u8 at91_leds_timer;
+
+void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+{
+	at91_leds_cpu	= cpu_led;
+	at91_leds_timer	= timer_led;
+}
+#else
+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_ATMEL)
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
+};
+
+static struct platform_device at91sam9261_dbgu_device = {
+	.name		= "atmel_usart",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &dbgu_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA9, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PA10, 1);		/* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_US0,
+		.end	= AT91SAM9261_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_US0,
+		.end	= AT91SAM9261_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9261_uart0_device = {
+	.name		= "atmel_usart",
+	.id		= 1,
+	.dev		= {
+				.platform_data	= &uart0_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PC8, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PC9, 0);		/* RXD0 */
+	at91_set_A_periph(AT91_PIN_PC10, 0);		/* RTS0 */
+	at91_set_A_periph(AT91_PIN_PC11, 0);		/* CTS0 */
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_US1,
+		.end	= AT91SAM9261_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_US1,
+		.end	= AT91SAM9261_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9261_uart1_device = {
+	.name		= "atmel_usart",
+	.id		= 2,
+	.dev		= {
+				.platform_data	= &uart1_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PC12, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PC13, 0);		/* RXD1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT91SAM9261_BASE_US2,
+		.end	= AT91SAM9261_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9261_ID_US2,
+		.end	= AT91SAM9261_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9261_uart2_device = {
+	.name		= "atmel_usart",
+	.id		= 3,
+	.dev		= {
+				.platform_data	= &uart2_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart2_resources,
+	.num_resources	= ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PC15, 0);		/* RXD2 */
+	at91_set_A_periph(AT91_PIN_PC14, 1);		/* TXD2 */
+}
+
+struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
+struct platform_device *atmel_default_console_device;	/* the serial console device */
+
+void __init at91_init_serial(struct at91_uart_config *config)
+{
+	int i;
+
+	/* Fill in list of supported UARTs */
+	for (i = 0; i < config->nr_tty; i++) {
+		switch (config->tty_map[i]) {
+			case 0:
+				configure_usart0_pins();
+				at91_uarts[i] = &at91sam9261_uart0_device;
+				at91_clock_associate("usart0_clk", &at91sam9261_uart0_device.dev, "usart");
+				break;
+			case 1:
+				configure_usart1_pins();
+				at91_uarts[i] = &at91sam9261_uart1_device;
+				at91_clock_associate("usart1_clk", &at91sam9261_uart1_device.dev, "usart");
+				break;
+			case 2:
+				configure_usart2_pins();
+				at91_uarts[i] = &at91sam9261_uart2_device;
+				at91_clock_associate("usart2_clk", &at91sam9261_uart2_device.dev, "usart");
+				break;
+			case 3:
+				configure_dbgu_pins();
+				at91_uarts[i] = &at91sam9261_dbgu_device;
+				at91_clock_associate("mck", &at91sam9261_dbgu_device.dev, "usart");
+				break;
+			default:
+				continue;
+		}
+		at91_uarts[i]->id = i;		/* update ID number to mapped ID */
+	}
+
+	/* Set serial console device */
+	if (config->console_tty < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[config->console_tty];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
+void __init at91_add_device_serial(void)
+{
+	int i;
+
+	for (i = 0; i < ATMEL_MAX_UART; i++) {
+		if (at91_uarts[i])
+			platform_device_register(at91_uarts[i]);
+	}
+}
+#else
+void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init at91_add_standard_devices(void)
+{
+	return 0;
+}
+
+arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c
new file mode 100644
index 0000000..59cbbe1
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam926x_time.c
@@ -0,0 +1,114 @@
+/*
+ * linux/arch/arm/mach-at91/at91sam926x_time.c
+ *
+ * Copyright (C) 2005-2006 M. Amine SAYA, ATMEL Rousset, France
+ * Revision	 2005 M. Nicolas Diremdjian, ATMEL Rousset, France
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/time.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/mach/time.h>
+
+#include <asm/arch/at91_pit.h>
+
+
+#define PIT_CPIV(x)	((x) & AT91_PIT_CPIV)
+#define PIT_PICNT(x)	(((x) & AT91_PIT_PICNT) >> 20)
+
+/*
+ * Returns number of microseconds since last timer interrupt.  Note that interrupts
+ * will have been disabled by do_gettimeofday()
+ *  'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy.
+ *  'tick' is usecs per jiffy (linux/timex.h).
+ */
+static unsigned long at91sam926x_gettimeoffset(void)
+{
+	unsigned long elapsed;
+	unsigned long t = at91_sys_read(AT91_PIT_PIIR);
+
+	elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t);		/* hardware clock cycles */
+
+	return (unsigned long)(elapsed * 1000000) / LATCH;
+}
+
+/*
+ * IRQ handler for the timer.
+ */
+static irqreturn_t at91sam926x_timer_interrupt(int irq, void *dev_id)
+{
+	volatile long nr_ticks;
+
+	if (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS) {	/* This is a shared interrupt */
+		write_seqlock(&xtime_lock);
+
+		/* Get number to ticks performed before interrupt and clear PIT interrupt */
+		nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
+		do {
+			timer_tick();
+			nr_ticks--;
+		} while (nr_ticks);
+
+		write_sequnlock(&xtime_lock);
+		return IRQ_HANDLED;
+	} else
+		return IRQ_NONE;		/* not handled */
+}
+
+static struct irqaction at91sam926x_timer_irq = {
+	.name		= "at91_tick",
+	.flags		= IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER,
+	.handler	= at91sam926x_timer_interrupt
+};
+
+void at91sam926x_timer_reset(void)
+{
+	/* Disable timer */
+	at91_sys_write(AT91_PIT_MR, 0);
+
+	/* Clear any pending interrupts */
+	(void) at91_sys_read(AT91_PIT_PIVR);
+
+	/* Set Period Interval timer and enable its interrupt */
+	at91_sys_write(AT91_PIT_MR, (LATCH & AT91_PIT_PIV) | AT91_PIT_PITIEN | AT91_PIT_PITEN);
+}
+
+/*
+ * Set up timer interrupt.
+ */
+void __init at91sam926x_timer_init(void)
+{
+	/* Initialize and enable the timer */
+	at91sam926x_timer_reset();
+
+	/* Make IRQs happen for the system timer. */
+	setup_irq(AT91_ID_SYS, &at91sam926x_timer_irq);
+}
+
+#ifdef CONFIG_PM
+static void at91sam926x_timer_suspend(void)
+{
+	/* Disable timer */
+	at91_sys_write(AT91_PIT_MR, 0);
+}
+#else
+#define at91sam926x_timer_suspend	NULL
+#endif
+
+struct sys_timer at91sam926x_timer = {
+	.init		= at91sam926x_timer_init,
+	.offset		= at91sam926x_gettimeoffset,
+	.suspend	= at91sam926x_timer_suspend,
+	.resume		= at91sam926x_timer_reset,
+};
+
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
new file mode 100644
index 0000000..2d3d4b6
--- /dev/null
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -0,0 +1,102 @@
+/*
+ * linux/arch/arm/mach-at91/board-1arm.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata onearm_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 3,
+	.tty_map	= { 4, 0, 1, -1, -1 },		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init onearm_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&onearm_uart_config);
+}
+
+static void __init onearm_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata onearm_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata onearm_usbh_data = {
+	.ports		= 1,
+};
+
+static struct at91_udc_data __initdata onearm_udc_data = {
+	.vbus_pin	= AT91_PIN_PC2,
+	.pullup_pin	= AT91_PIN_PC3,
+};
+
+static void __init onearm_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&onearm_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&onearm_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&onearm_udc_data);
+}
+
+MACHINE_START(ONEARM, "Ajeco 1ARM single board computer")
+	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= onearm_map_io,
+	.init_irq	= onearm_init_irq,
+	.init_machine	= onearm_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
new file mode 100644
index 0000000..a081532
--- /dev/null
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -0,0 +1,149 @@
+/*
+ * linux/arch/arm/mach-at91/board-carmeva.c
+ *
+ *  Copyright (c) 2005 Peer Georgi
+ *  		       Conitec Datasystems
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata carmeva_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init carmeva_map_io(void)
+{
+	/* Initialize processor: 20.000 MHz crystal */
+	at91rm9200_initialize(20000000, AT91RM9200_BGA);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&carmeva_uart_config);
+}
+
+static void __init carmeva_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata carmeva_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata carmeva_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata carmeva_udc_data = {
+	.vbus_pin	= AT91_PIN_PD12,
+	.pullup_pin	= AT91_PIN_PD9,
+};
+
+/* FIXME: user dependend */
+// static struct at91_cf_data __initdata carmeva_cf_data = {
+//	.det_pin	= AT91_PIN_PB0,
+//	.rst_pin	= AT91_PIN_PC5,
+	// .irq_pin	= ... not connected
+	// .vcc_pin	= ... always powered
+// };
+
+static struct at91_mmc_data __initdata carmeva_mmc_data = {
+	.slot_b		= 0,
+	.wire4		= 1,
+	.det_pin	= AT91_PIN_PB10,
+	.wp_pin		= AT91_PIN_PC14,
+};
+
+static struct spi_board_info carmeva_spi_devices[] = {
+	{ /* DataFlash chip */
+		.modalias = "mtd_dataflash",
+		.chip_select  = 0,
+		.max_speed_hz = 10 * 1000 * 1000,
+	},
+	{ /* User accessable spi - cs1 (250KHz) */
+		.modalias = "spi-cs1",
+		.chip_select  = 1,
+		.max_speed_hz = 250 *  1000,
+	},
+	{ /* User accessable spi - cs2 (1MHz) */
+		.modalias = "spi-cs2",
+		.chip_select  = 2,
+		.max_speed_hz = 1 * 1000 *  1000,
+	},
+	{ /* User accessable spi - cs3 (10MHz) */
+		.modalias = "spi-cs3",
+		.chip_select  = 3,
+		.max_speed_hz = 10 * 1000 *  1000,
+	},
+};
+
+static void __init carmeva_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&carmeva_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&carmeva_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&carmeva_udc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* SPI */
+	at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices));
+	/* Compact Flash */
+//	at91_add_device_cf(&carmeva_cf_data);
+	/* MMC */
+	at91_add_device_mmc(&carmeva_mmc_data);
+}
+
+MACHINE_START(CARMEVA, "Carmeva")
+	/* Maintainer: Conitec Datasystems */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= carmeva_map_io,
+	.init_irq	= carmeva_init_irq,
+	.init_machine	= carmeva_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
new file mode 100644
index 0000000..45d6d9b
--- /dev/null
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -0,0 +1,145 @@
+/*
+ * linux/arch/arm/mach-at91/board-csb337.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata csb337_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init csb337_map_io(void)
+{
+	/* Initialize processor: 3.6864 MHz crystal */
+	at91rm9200_initialize(3686400, AT91RM9200_BGA);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&csb337_uart_config);
+}
+
+static void __init csb337_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata csb337_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC2,
+	.is_rmii	= 0,
+};
+
+static struct at91_usbh_data __initdata csb337_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata csb337_udc_data = {
+	// this has no VBUS sensing pin
+	.pullup_pin	= AT91_PIN_PA24,
+};
+
+static struct at91_cf_data __initdata csb337_cf_data = {
+	/*
+	 * connector P4 on the CSB 337 mates to
+	 * connector P8 on the CSB 300CF
+	 */
+
+	/* CSB337 specific */
+	.det_pin	= AT91_PIN_PC3,
+
+	/* CSB300CF specific */
+	.irq_pin	= AT91_PIN_PA19,
+	.vcc_pin	= AT91_PIN_PD0,
+	.rst_pin	= AT91_PIN_PD2,
+};
+
+static struct at91_mmc_data __initdata csb337_mmc_data = {
+	.det_pin	= AT91_PIN_PD5,
+	.slot_b		= 0,
+	.wire4		= 1,
+	.wp_pin		= AT91_PIN_PD6,
+};
+
+static struct spi_board_info csb337_spi_devices[] = {
+	{	/* CAN controller */
+		.modalias	= "sak82c900",
+		.chip_select	= 0,
+		.max_speed_hz	= 6 * 1000 * 1000,
+	},
+};
+
+static void __init csb337_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&csb337_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&csb337_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&csb337_udc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* Compact Flash */
+	at91_set_gpio_input(AT91_PIN_PB22, 1);		/* IOIS16 */
+	at91_add_device_cf(&csb337_cf_data);
+	/* SPI */
+	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
+	/* MMC */
+	at91_add_device_mmc(&csb337_mmc_data);
+}
+
+MACHINE_START(CSB337, "Cogent CSB337")
+	/* Maintainer: Bill Gatliff */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= csb337_map_io,
+	.init_irq	= csb337_init_irq,
+	.init_machine	= csb337_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
new file mode 100644
index 0000000..7746094
--- /dev/null
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -0,0 +1,109 @@
+/*
+ * linux/arch/arm/mach-at91/board-csb637.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata csb637_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init csb637_map_io(void)
+{
+	/* Initialize processor: 3.6864 MHz crystal */
+	at91rm9200_initialize(3686400, AT91RM9200_BGA);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&csb637_uart_config);
+}
+
+static void __init csb637_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata csb637_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC0,
+	.is_rmii	= 0,
+};
+
+static struct at91_usbh_data __initdata csb637_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata csb637_udc_data = {
+	.vbus_pin     = AT91_PIN_PB28,
+	.pullup_pin   = AT91_PIN_PB1,
+};
+
+static void __init csb637_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&csb637_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&csb637_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&csb637_udc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* SPI */
+	at91_add_device_spi(NULL, 0);
+}
+
+MACHINE_START(CSB637, "Cogent CSB637")
+	/* Maintainer: Bill Gatliff */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= csb637_map_io,
+	.init_irq	= csb637_init_irq,
+	.init_machine	= csb637_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-dk.c b/arch/arm/mach-at91/board-dk.c
new file mode 100644
index 0000000..7401dbe
--- /dev/null
+++ b/arch/arm/mach-at91/board-dk.c
@@ -0,0 +1,216 @@
+/*
+ * linux/arch/arm/mach-at91/board-dk.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ *  Epson S1D framebuffer glue code is:
+ *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91rm9200_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata dk_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init dk_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_BGA);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&dk_uart_config);
+}
+
+static void __init dk_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata dk_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata dk_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata dk_udc_data = {
+	.vbus_pin	= AT91_PIN_PD4,
+	.pullup_pin	= AT91_PIN_PD5,
+};
+
+static struct at91_cf_data __initdata dk_cf_data = {
+	.det_pin	= AT91_PIN_PB0,
+	.rst_pin	= AT91_PIN_PC5,
+	// .irq_pin	= ... not connected
+	// .vcc_pin	= ... always powered
+};
+
+static struct at91_mmc_data __initdata dk_mmc_data = {
+	.slot_b		= 0,
+	.wire4		= 1,
+};
+
+static struct spi_board_info dk_spi_devices[] = {
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+	},
+	{	/* UR6HCPS2-SP40 PS2-to-SPI adapter */
+		.modalias	= "ur6hcps2",
+		.chip_select	= 1,
+		.max_speed_hz	= 250 *  1000,
+	},
+	{	/* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
+		.modalias	= "tlv1504",
+		.chip_select	= 2,
+		.max_speed_hz	= 20 * 1000 * 1000,
+	},
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 3,
+		.max_speed_hz	= 15 * 1000 * 1000,
+	}
+#endif
+};
+
+static struct mtd_partition __initdata dk_nand_partition[] = {
+	{
+		.name	= "NAND Partition 1",
+		.offset	= 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(dk_nand_partition);
+	return dk_nand_partition;
+}
+
+static struct at91_nand_data __initdata dk_nand_data = {
+	.ale		= 22,
+	.cle		= 21,
+	.det_pin	= AT91_PIN_PB1,
+	.rdy_pin	= AT91_PIN_PC2,
+	// .enable_pin	= ... not there
+	.partition_info	= nand_partitions,
+};
+
+#define DK_FLASH_BASE	AT91_CHIPSELECT_0
+#define DK_FLASH_SIZE	0x200000
+
+static struct physmap_flash_data dk_flash_data = {
+	.width	= 2,
+};
+
+static struct resource dk_flash_resource = {
+	.start		= DK_FLASH_BASE,
+	.end		= DK_FLASH_BASE + DK_FLASH_SIZE - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device dk_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &dk_flash_data,
+			},
+	.resource	= &dk_flash_resource,
+	.num_resources	= 1,
+};
+
+
+static void __init dk_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&dk_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&dk_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&dk_udc_data);
+	at91_set_multi_drive(dk_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
+	/* Compact Flash */
+	at91_add_device_cf(&dk_cf_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* SPI */
+	at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+	/* DataFlash card */
+	at91_set_gpio_output(AT91_PIN_PB7, 0);
+#else
+	/* MMC */
+	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
+	at91_add_device_mmc(&dk_mmc_data);
+#endif
+	/* NAND */
+	at91_add_device_nand(&dk_nand_data);
+	/* NOR Flash */
+	platform_device_register(&dk_flash);
+	/* VGA */
+//	dk_add_device_video();
+}
+
+MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
+	/* Maintainer: SAN People/Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= dk_map_io,
+	.init_irq	= dk_init_irq,
+	.init_machine	= dk_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
new file mode 100644
index 0000000..56d5ef6
--- /dev/null
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -0,0 +1,123 @@
+/*
+ * linux/arch/arm/mach-at91/board-eb9200.c
+ *
+ *  Copyright (C) 2005 SAN People, adapted for ATEB9200 from Embest
+ *  by Andrew Patrikalakis
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata eb9200_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init eb9200_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_BGA);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&eb9200_uart_config);
+}
+
+static void __init eb9200_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata eb9200_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata eb9200_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata eb9200_udc_data = {
+	.vbus_pin	= AT91_PIN_PD4,
+	.pullup_pin	= AT91_PIN_PD5,
+};
+
+static struct at91_cf_data __initdata eb9200_cf_data = {
+	.det_pin	= AT91_PIN_PB0,
+	.rst_pin	= AT91_PIN_PC5,
+	// .irq_pin	= ... not connected
+	// .vcc_pin	= ... always powered
+};
+
+static struct at91_mmc_data __initdata eb9200_mmc_data = {
+	.slot_b		= 0,
+	.wire4		= 1,
+};
+
+static void __init eb9200_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&eb9200_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&eb9200_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&eb9200_udc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* Compact Flash */
+	at91_add_device_cf(&eb9200_cf_data);
+	/* SPI */
+	at91_add_device_spi(NULL, 0);
+	/* MMC */
+	/* only supports 1 or 4 bit interface, not wired through to SPI */
+	at91_add_device_mmc(&eb9200_mmc_data);
+}
+
+MACHINE_START(ATEB9200, "Embest ATEB9200")
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= eb9200_map_io,
+	.init_irq	= eb9200_init_irq,
+	.init_machine	= eb9200_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-ek.c
new file mode 100644
index 0000000..0f589dd
--- /dev/null
+++ b/arch/arm/mach-at91/board-ek.c
@@ -0,0 +1,174 @@
+/*
+ * linux/arch/arm/mach-at91/board-ek.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ *  Epson S1D framebuffer glue code is:
+ *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91rm9200_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata ek_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_BGA);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&ek_uart_config);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata ek_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PD4,
+	.pullup_pin	= AT91_PIN_PD5,
+};
+
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.det_pin	= AT91_PIN_PB27,
+	.slot_b		= 0,
+	.wire4		= 1,
+	.wp_pin		= AT91_PIN_PA17,
+};
+
+static struct spi_board_info ek_spi_devices[] = {
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+	},
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 3,
+		.max_speed_hz	= 15 * 1000 * 1000,
+	},
+#endif
+};
+
+#define EK_FLASH_BASE	AT91_CHIPSELECT_0
+#define EK_FLASH_SIZE	0x200000
+
+static struct physmap_flash_data ek_flash_data = {
+	.width	= 2,
+};
+
+static struct resource ek_flash_resource = {
+	.start		= EK_FLASH_BASE,
+	.end		= EK_FLASH_BASE + EK_FLASH_SIZE - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device ek_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &ek_flash_data,
+			},
+	.resource	= &ek_flash_resource,
+	.num_resources	= 1,
+};
+
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&ek_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	at91_set_multi_drive(ek_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
+	/* I2C */
+	at91_add_device_i2c();
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+	/* DataFlash card */
+	at91_set_gpio_output(AT91_PIN_PB22, 0);
+#else
+	/* MMC */
+	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
+	at91_add_device_mmc(&ek_mmc_data);
+#endif
+	/* NOR Flash */
+	platform_device_register(&ek_flash);
+	/* VGA */
+//	ek_add_device_video();
+}
+
+MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
+	/* Maintainer: SAN People/Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
new file mode 100644
index 0000000..c77d84c
--- /dev/null
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -0,0 +1,109 @@
+/*
+ * linux/arch/arm/mach-at91/board-kafa.c
+ *
+ *  Copyright (C) 2006 Sperry-Sun
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata kafa_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 4, 0, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
+};
+
+static void __init kafa_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
+
+	/* Set up the LEDs */
+	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&kafa_uart_config);
+}
+
+static void __init kafa_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata kafa_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 0,
+};
+
+static struct at91_usbh_data __initdata kafa_usbh_data = {
+	.ports		= 1,
+};
+
+static struct at91_udc_data __initdata kafa_udc_data = {
+	.vbus_pin	= AT91_PIN_PB6,
+	.pullup_pin	= AT91_PIN_PB7,
+};
+
+static void __init kafa_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&kafa_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&kafa_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&kafa_udc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* SPI */
+	at91_add_device_spi(NULL, 0);
+}
+
+MACHINE_START(KAFA, "Sperry-Sun KAFA")
+	/* Maintainer: Sergei Sharonov */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= kafa_map_io,
+	.init_irq	= kafa_init_irq,
+	.init_machine	= kafa_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
new file mode 100644
index 0000000..17e68f5
--- /dev/null
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -0,0 +1,143 @@
+/*
+ * linux/arch/arm/mach-at91/board-kb9202.c
+ *
+ *  Copyright (c) 2005 kb_admin
+ *  		       KwikByte, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 3 = USART0 .. USART3
+ *    4      = DBGU
+ */
+static struct at91_uart_config __initdata kb9202_uart_config = {
+	.console_tty	= 0,					/* ttyS0 */
+	.nr_tty		= 3,
+	.tty_map	= { 4, 0, 1, -1, -1 }			/* ttyS0, ..., ttyS4 */
+};
+
+static void __init kb9202_map_io(void)
+{
+	/* Initialize processor: 10 MHz crystal */
+	at91rm9200_initialize(10000000, AT91RM9200_PQFP);
+
+	/* Set up the LEDs */
+	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&kb9202_uart_config);
+}
+
+static void __init kb9202_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata kb9202_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PB29,
+	.is_rmii	= 0,
+};
+
+static struct at91_usbh_data __initdata kb9202_usbh_data = {
+	.ports		= 1,
+};
+
+static struct at91_udc_data __initdata kb9202_udc_data = {
+	.vbus_pin	= AT91_PIN_PB24,
+	.pullup_pin	= AT91_PIN_PB22,
+};
+
+static struct at91_mmc_data __initdata kb9202_mmc_data = {
+	.det_pin	= AT91_PIN_PB2,
+	.slot_b		= 0,
+	.wire4		= 1,
+};
+
+static struct mtd_partition __initdata kb9202_nand_partition[] = {
+	{
+		.name	= "nand_fs",
+		.offset	= 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(kb9202_nand_partition);
+	return kb9202_nand_partition;
+}
+
+static struct at91_nand_data __initdata kb9202_nand_data = {
+	.ale		= 22,
+	.cle		= 21,
+	// .det_pin	= ... not there
+	.rdy_pin	= AT91_PIN_PC29,
+	.enable_pin	= AT91_PIN_PC28,
+	.partition_info	= nand_partitions,
+};
+
+static void __init kb9202_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&kb9202_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&kb9202_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&kb9202_udc_data);
+	/* MMC */
+	at91_add_device_mmc(&kb9202_mmc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* SPI */
+	at91_add_device_spi(NULL, 0);
+	/* NAND */
+	at91_add_device_nand(&kb9202_nand_data);
+}
+
+MACHINE_START(KB9200, "KB920x")
+	/* Maintainer: KwikByte, Inc. */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= kb9202_map_io,
+	.init_irq	= kb9202_init_irq,
+	.init_machine	= kb9202_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
new file mode 100644
index 0000000..6ae272d
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -0,0 +1,202 @@
+/*
+ * linux/arch/arm/mach-at91/board-ek.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam926x_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 5 = USART0 .. USART5
+ *    6      = DBGU
+ */
+static struct at91_uart_config __initdata ek_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 3,
+	.tty_map	= { 6, 0, 1, -1, -1, -1, -1 }	/* ttyS0, ..., ttyS6 */
+};
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91sam9260_initialize(18432000);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&ek_uart_config);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PC5,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 1,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+#endif
+#if defined(CONFIG_SND_AT73C213)
+	{	/* AT73C213 DAC */
+		.modalias	= "snd_at73c213",
+		.chip_select	= 0,
+		.max_speed_hz	= 10 * 1000 * 1000,
+		.bus_num	= 1,
+	},
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct __initdata at91_eth_data ek_macb_data = {
+	.phy_irq_pin	= AT91_PIN_PA7,
+	.is_rmii	= 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name	= "Partition 1",
+		.offset	= 0,
+		.size	= 256 * 1024,
+	},
+	{
+		.name	= "Partition 2",
+		.offset	= 256 * 1024,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+//	.det_pin	= ... not connected
+	.rdy_pin	= AT91_PIN_PC13,
+	.enable_pin	= AT91_PIN_PC14,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.slot_b		= 1,
+	.wire4		= 1,
+//	.det_pin	= ... not connected
+//	.wp_pin		= ... not connected
+//	.vcc_pin	= ... not connected
+};
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+	/* NAND */
+	at91_add_device_nand(&ek_nand_data);
+	/* Ethernet */
+	at91_add_device_eth(&ek_macb_data);
+	/* MMC */
+	at91_add_device_mmc(&ek_mmc_data);
+}
+
+MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
+	/* Maintainer: Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
new file mode 100644
index 0000000..25d6263
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -0,0 +1,259 @@
+/*
+ * linux/arch/arm/mach-at91/board-ek.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/dm9000.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam926x_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 2 = USART0 .. USART2
+ *    3      = DBGU
+ */
+static struct at91_uart_config __initdata ek_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 1,
+	.tty_map	= { 3, -1, -1, -1 }		/* ttyS0, ..., ttyS3 */
+};
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91sam9261_initialize(18432000);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&ek_uart_config);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91sam9261_init_interrupts(NULL);
+}
+
+
+/*
+ * DM9000 ethernet device
+ */
+#if defined(CONFIG_DM9000)
+static struct resource at91sam9261_dm9000_resource[] = {
+	[0] = {
+		.start	= AT91_CHIPSELECT_2,
+		.end	= AT91_CHIPSELECT_2 + 3,
+		.flags	= IORESOURCE_MEM
+	},
+	[1] = {
+		.start	= AT91_CHIPSELECT_2 + 0x44,
+		.end	= AT91_CHIPSELECT_2 + 0xFF,
+		.flags	= IORESOURCE_MEM
+	},
+	[2] = {
+		.start	= AT91_PIN_PC11,
+		.end	= AT91_PIN_PC11,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+static struct dm9000_plat_data dm9000_platdata = {
+	.flags		= DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device at91sam9261_dm9000_device = {
+	.name		= "dm9000",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(at91sam9261_dm9000_resource),
+	.resource	= at91sam9261_dm9000_resource,
+	.dev		= {
+		.platform_data	= &dm9000_platdata,
+	}
+};
+
+static void __init ek_add_device_dm9000(void)
+{
+	/*
+	 * Configure Chip-Select 2 on SMC for the DM9000.
+	 * Note: These timings were calculated for MASTER_CLOCK = 100000000
+	 *  according to the DM9000 timings.
+	 */
+	at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
+	at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
+	at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
+	at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+
+	/* Configure Reset signal as output */
+	at91_set_gpio_output(AT91_PIN_PC10, 0);
+
+	/* Configure Interrupt pin as input, no pull-up */
+	at91_set_gpio_input(AT91_PIN_PC11, 0);
+
+	platform_device_register(&at91sam9261_dm9000_device);
+}
+#else
+static void __init ek_add_device_dm9000(void) {}
+#endif /* CONFIG_DM9000 */
+
+
+/*
+ * USB Host Port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+
+/*
+ * USB Device Port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PB29,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.wire4		= 1,
+//	.det_pin	= ... not connected
+//	.wp_pin		= ... not connected
+//	.vcc_pin	= ... not connected
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name	= "Partition 1",
+		.offset	= 0,
+		.size	= 256 * 1024,
+	},
+	{
+		.name	= "Partition 2",
+		.offset	= 256 * 1024 ,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+	.ale		= 22,
+	.cle		= 21,
+//	.det_pin	= ... not connected
+	.rdy_pin	= AT91_PIN_PC15,
+	.enable_pin	= AT91_PIN_PC14,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+/*
+ * SPI devices
+ */
+static struct spi_board_info ek_spi_devices[] = {
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card - jumper (J12) configurable to CS3 or CS0 */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 3,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#elif defined(CONFIG_SND_AT73C213)
+	{	/* AT73C213 DAC */
+		.modalias	= "snd_at73c213",
+		.chip_select	= 3,
+		.max_speed_hz	= 10 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+};
+
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	/* I2C */
+	at91_add_device_i2c();
+	/* NAND */
+	at91_add_device_nand(&ek_nand_data);
+	/* DM9000 ethernet */
+	ek_add_device_dm9000();
+
+	/* spi0 and mmc/sd share the same PIO pins */
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+#else
+	/* MMC */
+	at91_add_device_mmc(&ek_mmc_data);
+#endif
+}
+
+MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK")
+	/* Maintainer: Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
new file mode 100644
index 0000000..baab095
--- /dev/null
+++ b/arch/arm/mach-at91/clock.c
@@ -0,0 +1,644 @@
+/*
+ * linux/arch/arm/mach-at91/clock.c
+ *
+ * Copyright (C) 2005 David Brownell
+ * Copyright (C) 2005 Ivan Kokshaysky
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/fs.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include <asm/semaphore.h>
+#include <asm/io.h>
+#include <asm/mach-types.h>
+
+#include <asm/hardware.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/cpu.h>
+
+#include "clock.h"
+
+
+/*
+ * There's a lot more which can be done with clocks, including cpufreq
+ * integration, slow clock mode support (for system suspend), letting
+ * PLLB be used at other rates (on boards that don't need USB), etc.
+ */
+
+#define clk_is_primary(x)	((x)->type & CLK_TYPE_PRIMARY)
+#define clk_is_programmable(x)	((x)->type & CLK_TYPE_PROGRAMMABLE)
+#define clk_is_peripheral(x)	((x)->type & CLK_TYPE_PERIPHERAL)
+#define clk_is_sys(x)		((x)->type & CLK_TYPE_SYSTEM)
+
+
+static LIST_HEAD(clocks);
+static DEFINE_SPINLOCK(clk_lock);
+
+static u32 at91_pllb_usb_init;
+
+/*
+ * Four primary clock sources:  two crystal oscillators (32K, main), and
+ * two PLLs.  PLLA usually runs the master clock; and PLLB must run at
+ * 48 MHz (unless no USB function clocks are needed).  The main clock and
+ * both PLLs are turned off to run in "slow clock mode" (system suspend).
+ */
+static struct clk clk32k = {
+	.name		= "clk32k",
+	.rate_hz	= AT91_SLOW_CLOCK,
+	.users		= 1,		/* always on */
+	.id		= 0,
+	.type		= CLK_TYPE_PRIMARY,
+};
+static struct clk main_clk = {
+	.name		= "main",
+	.pmc_mask	= AT91_PMC_MOSCS,	/* in PMC_SR */
+	.id		= 1,
+	.type		= CLK_TYPE_PRIMARY,
+};
+static struct clk plla = {
+	.name		= "plla",
+	.parent		= &main_clk,
+	.pmc_mask	= AT91_PMC_LOCKA,	/* in PMC_SR */
+	.id		= 2,
+	.type		= CLK_TYPE_PRIMARY | CLK_TYPE_PLL,
+};
+
+static void pllb_mode(struct clk *clk, int is_on)
+{
+	u32	value;
+
+	if (is_on) {
+		is_on = AT91_PMC_LOCKB;
+		value = at91_pllb_usb_init;
+	} else
+		value = 0;
+
+	// REVISIT: Add work-around for AT91RM9200 Errata #26 ?
+	at91_sys_write(AT91_CKGR_PLLBR, value);
+
+	do {
+		cpu_relax();
+	} while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on);
+}
+
+static struct clk pllb = {
+	.name		= "pllb",
+	.parent		= &main_clk,
+	.pmc_mask	= AT91_PMC_LOCKB,	/* in PMC_SR */
+	.mode		= pllb_mode,
+	.id		= 3,
+	.type		= CLK_TYPE_PRIMARY | CLK_TYPE_PLL,
+};
+
+static void pmc_sys_mode(struct clk *clk, int is_on)
+{
+	if (is_on)
+		at91_sys_write(AT91_PMC_SCER, clk->pmc_mask);
+	else
+		at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask);
+}
+
+/* USB function clocks (PLLB must be 48 MHz) */
+static struct clk udpck = {
+	.name		= "udpck",
+	.parent		= &pllb,
+	.mode		= pmc_sys_mode,
+};
+static struct clk uhpck = {
+	.name		= "uhpck",
+	.parent		= &pllb,
+	.mode		= pmc_sys_mode,
+};
+
+
+/*
+ * The master clock is divided from the CPU clock (by 1-4).  It's used for
+ * memory, interfaces to on-chip peripherals, the AIC, and sometimes more
+ * (e.g baud rate generation).  It's sourced from one of the primary clocks.
+ */
+static struct clk mck = {
+	.name		= "mck",
+	.pmc_mask	= AT91_PMC_MCKRDY,	/* in PMC_SR */
+};
+
+static void pmc_periph_mode(struct clk *clk, int is_on)
+{
+	if (is_on)
+		at91_sys_write(AT91_PMC_PCER, clk->pmc_mask);
+	else
+		at91_sys_write(AT91_PMC_PCDR, clk->pmc_mask);
+}
+
+static struct clk __init *at91_css_to_clk(unsigned long css)
+{
+	switch (css) {
+		case AT91_PMC_CSS_SLOW:
+			return &clk32k;
+		case AT91_PMC_CSS_MAIN:
+			return &main_clk;
+		case AT91_PMC_CSS_PLLA:
+			return &plla;
+		case AT91_PMC_CSS_PLLB:
+			return &pllb;
+	}
+
+	return NULL;
+}
+
+/*
+ * Associate a particular clock with a function (eg, "uart") and device.
+ * The drivers can then request the same 'function' with several different
+ * devices and not care about which clock name to use.
+ */
+void __init at91_clock_associate(const char *id, struct device *dev, const char *func)
+{
+	struct clk *clk = clk_get(NULL, id);
+
+	if (!dev || !clk || !IS_ERR(clk_get(dev, func)))
+		return;
+
+	clk->function = func;
+	clk->dev = dev;
+}
+
+/* clocks cannot be de-registered no refcounting necessary */
+struct clk *clk_get(struct device *dev, const char *id)
+{
+	struct clk *clk;
+
+	list_for_each_entry(clk, &clocks, node) {
+		if (strcmp(id, clk->name) == 0)
+			return clk;
+		if (clk->function && (dev == clk->dev) && strcmp(id, clk->function) == 0)
+			return clk;
+	}
+
+	return ERR_PTR(-ENOENT);
+}
+EXPORT_SYMBOL(clk_get);
+
+void clk_put(struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_put);
+
+static void __clk_enable(struct clk *clk)
+{
+	if (clk->parent)
+		__clk_enable(clk->parent);
+	if (clk->users++ == 0 && clk->mode)
+		clk->mode(clk, 1);
+}
+
+int clk_enable(struct clk *clk)
+{
+	unsigned long	flags;
+
+	spin_lock_irqsave(&clk_lock, flags);
+	__clk_enable(clk);
+	spin_unlock_irqrestore(&clk_lock, flags);
+	return 0;
+}
+EXPORT_SYMBOL(clk_enable);
+
+static void __clk_disable(struct clk *clk)
+{
+	BUG_ON(clk->users == 0);
+	if (--clk->users == 0 && clk->mode)
+		clk->mode(clk, 0);
+	if (clk->parent)
+		__clk_disable(clk->parent);
+}
+
+void clk_disable(struct clk *clk)
+{
+	unsigned long	flags;
+
+	spin_lock_irqsave(&clk_lock, flags);
+	__clk_disable(clk);
+	spin_unlock_irqrestore(&clk_lock, flags);
+}
+EXPORT_SYMBOL(clk_disable);
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	unsigned long	flags;
+	unsigned long	rate;
+
+	spin_lock_irqsave(&clk_lock, flags);
+	for (;;) {
+		rate = clk->rate_hz;
+		if (rate || !clk->parent)
+			break;
+		clk = clk->parent;
+	}
+	spin_unlock_irqrestore(&clk_lock, flags);
+	return rate;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+/*------------------------------------------------------------------------*/
+
+#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
+
+/*
+ * For now, only the programmable clocks support reparenting (MCK could
+ * do this too, with care) or rate changing (the PLLs could do this too,
+ * ditto MCK but that's more for cpufreq).  Drivers may reparent to get
+ * a better rate match; we don't.
+ */
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	unsigned long	flags;
+	unsigned	prescale;
+	unsigned long	actual;
+
+	if (!clk_is_programmable(clk))
+		return -EINVAL;
+	spin_lock_irqsave(&clk_lock, flags);
+
+	actual = clk->parent->rate_hz;
+	for (prescale = 0; prescale < 7; prescale++) {
+		if (actual && actual <= rate)
+			break;
+		actual >>= 1;
+	}
+
+	spin_unlock_irqrestore(&clk_lock, flags);
+	return (prescale < 7) ? actual : -ENOENT;
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	unsigned long	flags;
+	unsigned	prescale;
+	unsigned long	actual;
+
+	if (!clk_is_programmable(clk))
+		return -EINVAL;
+	if (clk->users)
+		return -EBUSY;
+	spin_lock_irqsave(&clk_lock, flags);
+
+	actual = clk->parent->rate_hz;
+	for (prescale = 0; prescale < 7; prescale++) {
+		if (actual && actual <= rate) {
+			u32	pckr;
+
+			pckr = at91_sys_read(AT91_PMC_PCKR(clk->id));
+			pckr &= AT91_PMC_CSS_PLLB;	/* clock selection */
+			pckr |= prescale << 2;
+			at91_sys_write(AT91_PMC_PCKR(clk->id), pckr);
+			clk->rate_hz = actual;
+			break;
+		}
+		actual >>= 1;
+	}
+
+	spin_unlock_irqrestore(&clk_lock, flags);
+	return (prescale < 7) ? actual : -ENOENT;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	unsigned long	flags;
+
+	if (clk->users)
+		return -EBUSY;
+	if (!clk_is_primary(parent) || !clk_is_programmable(clk))
+		return -EINVAL;
+	spin_lock_irqsave(&clk_lock, flags);
+
+	clk->rate_hz = parent->rate_hz;
+	clk->parent = parent;
+	at91_sys_write(AT91_PMC_PCKR(clk->id), parent->id);
+
+	spin_unlock_irqrestore(&clk_lock, flags);
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
+/* establish PCK0..PCK3 parentage and rate */
+static void init_programmable_clock(struct clk *clk)
+{
+	struct clk	*parent;
+	u32		pckr;
+
+	pckr = at91_sys_read(AT91_PMC_PCKR(clk->id));
+	parent = at91_css_to_clk(pckr & AT91_PMC_CSS);
+	clk->parent = parent;
+	clk->rate_hz = parent->rate_hz / (1 << ((pckr >> 2) & 3));
+}
+
+#endif	/* CONFIG_AT91_PROGRAMMABLE_CLOCKS */
+
+/*------------------------------------------------------------------------*/
+
+#ifdef CONFIG_DEBUG_FS
+
+static int at91_clk_show(struct seq_file *s, void *unused)
+{
+	u32		scsr, pcsr, sr;
+	struct clk	*clk;
+	unsigned	i;
+
+	seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR));
+	seq_printf(s, "PCSR = %8x\n", pcsr = at91_sys_read(AT91_PMC_PCSR));
+
+	seq_printf(s, "MOR  = %8x\n", at91_sys_read(AT91_CKGR_MOR));
+	seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR));
+	seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR));
+	seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR));
+
+	seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR));
+	for (i = 0; i < 4; i++)
+		seq_printf(s, "PCK%d = %8x\n", i, at91_sys_read(AT91_PMC_PCKR(i)));
+	seq_printf(s, "SR   = %8x\n", sr = at91_sys_read(AT91_PMC_SR));
+
+	seq_printf(s, "\n");
+
+	list_for_each_entry(clk, &clocks, node) {
+		char	*state;
+
+		if (clk->mode == pmc_sys_mode)
+			state = (scsr & clk->pmc_mask) ? "on" : "off";
+		else if (clk->mode == pmc_periph_mode)
+			state = (pcsr & clk->pmc_mask) ? "on" : "off";
+		else if (clk->pmc_mask)
+			state = (sr & clk->pmc_mask) ? "on" : "off";
+		else if (clk == &clk32k || clk == &main_clk)
+			state = "on";
+		else
+			state = "";
+
+		seq_printf(s, "%-10s users=%2d %-3s %9ld Hz %s\n",
+			clk->name, clk->users, state, clk_get_rate(clk),
+			clk->parent ? clk->parent->name : "");
+	}
+	return 0;
+}
+
+static int at91_clk_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, at91_clk_show, NULL);
+}
+
+static struct file_operations at91_clk_operations = {
+	.open		= at91_clk_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static int __init at91_clk_debugfs_init(void)
+{
+	/* /sys/kernel/debug/at91_clk */
+	(void) debugfs_create_file("at91_clk", S_IFREG | S_IRUGO, NULL, NULL, &at91_clk_operations);
+
+	return 0;
+}
+postcore_initcall(at91_clk_debugfs_init);
+
+#endif
+
+/*------------------------------------------------------------------------*/
+
+/* Register a new clock */
+int __init clk_register(struct clk *clk)
+{
+	if (clk_is_peripheral(clk)) {
+		clk->parent = &mck;
+		clk->mode = pmc_periph_mode;
+		list_add_tail(&clk->node, &clocks);
+	}
+	else if (clk_is_sys(clk)) {
+		clk->parent = &mck;
+		clk->mode = pmc_sys_mode;
+
+		list_add_tail(&clk->node, &clocks);
+	}
+#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
+	else if (clk_is_programmable(clk)) {
+		clk->mode = pmc_sys_mode;
+		init_programmable_clock(clk);
+		list_add_tail(&clk->node, &clocks);
+	}
+#endif
+
+	return 0;
+}
+
+
+/*------------------------------------------------------------------------*/
+
+static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg)
+{
+	unsigned mul, div;
+
+	div = reg & 0xff;
+	mul = (reg >> 16) & 0x7ff;
+	if (div && mul) {
+		freq /= div;
+		freq *= mul + 1;
+	} else
+		freq = 0;
+
+	return freq;
+}
+
+static u32 __init at91_usb_rate(struct clk *pll, u32 freq, u32 reg)
+{
+	if (pll == &pllb && (reg & AT91_PMC_USB96M))
+		return freq / 2;
+	else
+		return freq;
+}
+
+static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq)
+{
+	unsigned i, div = 0, mul = 0, diff = 1 << 30;
+	unsigned ret = (out_freq > 155000000) ? 0xbe00 : 0x3e00;
+
+	/* PLL output max 240 MHz (or 180 MHz per errata) */
+	if (out_freq > 240000000)
+		goto fail;
+
+	for (i = 1; i < 256; i++) {
+		int diff1;
+		unsigned input, mul1;
+
+		/*
+		 * PLL input between 1MHz and 32MHz per spec, but lower
+		 * frequences seem necessary in some cases so allow 100K.
+		 */
+		input = main_freq / i;
+		if (input < 100000)
+			continue;
+		if (input > 32000000)
+			continue;
+
+		mul1 = out_freq / input;
+		if (mul1 > 2048)
+			continue;
+		if (mul1 < 2)
+			goto fail;
+
+		diff1 = out_freq - input * mul1;
+		if (diff1 < 0)
+			diff1 = -diff1;
+		if (diff > diff1) {
+			diff = diff1;
+			div = i;
+			mul = mul1;
+			if (diff == 0)
+				break;
+		}
+	}
+	if (i == 256 && diff > (out_freq >> 5))
+		goto fail;
+	return ret | ((mul - 1) << 16) | div;
+fail:
+	return 0;
+}
+
+/*
+ * Several unused clocks may be active.  Turn them off.
+ */
+static void __init at91_periphclk_reset(void)
+{
+	unsigned long reg;
+	struct clk *clk;
+
+	reg = at91_sys_read(AT91_PMC_PCSR);
+
+	list_for_each_entry(clk, &clocks, node) {
+		if (clk->mode != pmc_periph_mode)
+			continue;
+
+		if (clk->users > 0)
+			reg &= ~clk->pmc_mask;
+	}
+
+	at91_sys_write(AT91_PMC_PCDR, reg);
+}
+
+static struct clk *const standard_pmc_clocks[] __initdata = {
+	/* four primary clocks */
+	&clk32k,
+	&main_clk,
+	&plla,
+	&pllb,
+
+	/* PLLB children (USB) */
+	&udpck,
+	&uhpck,
+
+	/* MCK */
+	&mck
+};
+
+int __init at91_clock_init(unsigned long main_clock)
+{
+	unsigned tmp, freq, mckr;
+	int i;
+
+	/*
+	 * When the bootloader initialized the main oscillator correctly,
+	 * there's no problem using the cycle counter.  But if it didn't,
+	 * or when using oscillator bypass mode, we must be told the speed
+	 * of the main clock.
+	 */
+	if (!main_clock) {
+		do {
+			tmp = at91_sys_read(AT91_CKGR_MCFR);
+		} while (!(tmp & AT91_PMC_MAINRDY));
+		main_clock = (tmp & AT91_PMC_MAINF) * (AT91_SLOW_CLOCK / 16);
+	}
+	main_clk.rate_hz = main_clock;
+
+	/* report if PLLA is more than mildly overclocked */
+	plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
+	if (plla.rate_hz > 209000000)
+		pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
+
+	/*
+	 * USB clock init:  choose 48 MHz PLLB value, turn all clocks off,
+	 * disable 48MHz clock during usb peripheral suspend.
+	 *
+	 * REVISIT:  assumes MCK doesn't derive from PLLB!
+	 */
+	at91_pllb_usb_init = at91_pll_calc(main_clock, 48000000 * 2) | AT91_PMC_USB96M;
+	pllb.rate_hz = at91_pll_rate(&pllb, main_clock, at91_pllb_usb_init);
+	if (cpu_is_at91rm9200()) {
+		uhpck.pmc_mask = AT91RM9200_PMC_UHP;
+		udpck.pmc_mask = AT91RM9200_PMC_UDP;
+		at91_sys_write(AT91_PMC_SCDR, AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP);
+		at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
+	} else if (cpu_is_at91sam9260()) {
+		uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
+		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
+		at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP);
+	} else if (cpu_is_at91sam9261()) {
+		uhpck.pmc_mask = (AT91SAM926x_PMC_UHP | AT91_PMC_HCK0);
+		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
+		at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91_PMC_HCK0 | AT91SAM926x_PMC_UDP);
+	}
+	at91_sys_write(AT91_CKGR_PLLBR, 0);
+
+	udpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init);
+	uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init);
+
+	/*
+	 * MCK and CPU derive from one of those primary clocks.
+	 * For now, assume this parentage won't change.
+	 */
+	mckr = at91_sys_read(AT91_PMC_MCKR);
+	mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS);
+	freq = mck.parent->rate_hz;
+	freq /= (1 << ((mckr >> 2) & 3));		/* prescale */
+	mck.rate_hz = freq / (1 + ((mckr >> 8) & 3));	/* mdiv */
+
+	/* Register the PMC's standard clocks */
+	for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)
+		list_add_tail(&standard_pmc_clocks[i]->node, &clocks);
+
+	/* MCK and CPU clock are "always on" */
+	clk_enable(&mck);
+
+	printk("Clocks: CPU %u MHz, master %u MHz, main %u.%03u MHz\n",
+		freq / 1000000, (unsigned) mck.rate_hz / 1000000,
+		(unsigned) main_clock / 1000000,
+		((unsigned) main_clock % 1000000) / 1000);
+
+	/* disable all programmable clocks */
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK0 | AT91_PMC_PCK1 | AT91_PMC_PCK2 | AT91_PMC_PCK3);
+
+	/* disable all other unused peripheral clocks */
+	at91_periphclk_reset();
+
+	return 0;
+}
diff --git a/arch/arm/mach-at91/clock.h b/arch/arm/mach-at91/clock.h
new file mode 100644
index 0000000..1ba3b95
--- /dev/null
+++ b/arch/arm/mach-at91/clock.h
@@ -0,0 +1,31 @@
+/*
+ * linux/arch/arm/mach-at91/clock.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define CLK_TYPE_PRIMARY	0x1
+#define CLK_TYPE_PLL		0x2
+#define CLK_TYPE_PROGRAMMABLE	0x4
+#define CLK_TYPE_PERIPHERAL	0x8
+#define CLK_TYPE_SYSTEM		0x10
+
+
+struct clk {
+	struct list_head node;
+	const char	*name;		/* unique clock name */
+	const char	*function;	/* function of the clock */
+	struct device	*dev;		/* device associated with function */
+	unsigned long	rate_hz;
+	struct clk	*parent;
+	u32		pmc_mask;
+	void		(*mode)(struct clk *, int);
+	unsigned	id:2;		/* PCK0..3, or 32k/main/a/b */
+	unsigned	type;		/* clock type */
+	u16		users;
+};
+
+
+extern int __init clk_register(struct clk *clk);
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
new file mode 100644
index 0000000..10ee37b
--- /dev/null
+++ b/arch/arm/mach-at91/generic.h
@@ -0,0 +1,49 @@
+/*
+ * linux/arch/arm/mach-at91/generic.h
+ *
+ *  Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+ /* Processors */
+extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks);
+extern void __init at91sam9260_initialize(unsigned long main_clock);
+extern void __init at91sam9261_initialize(unsigned long main_clock);
+
+ /* Interrupts */
+extern void __init at91rm9200_init_interrupts(unsigned int priority[]);
+extern void __init at91sam9260_init_interrupts(unsigned int priority[]);
+extern void __init at91sam9261_init_interrupts(unsigned int priority[]);
+extern void __init at91_aic_init(unsigned int priority[]);
+
+ /* Timer */
+struct sys_timer;
+extern struct sys_timer at91rm9200_timer;
+extern struct sys_timer at91sam926x_timer;
+
+ /* Clocks */
+extern int __init at91_clock_init(unsigned long main_clock);
+struct device;
+extern void __init at91_clock_associate(const char *id, struct device *dev, const char *func);
+
+ /* Power Management */
+extern void at91_irq_suspend(void);
+extern void at91_irq_resume(void);
+
+ /* GPIO */
+#define AT91RM9200_PQFP		3	/* AT91RM9200 PQFP package has 3 banks */
+#define AT91RM9200_BGA		4	/* AT91RM9200 BGA package has 4 banks */
+
+struct at91_gpio_bank {
+	unsigned short id;		/* peripheral ID */
+	unsigned long offset;		/* offset from system peripheral base */
+	struct clk *clock;		/* associated clock */
+};
+extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
+extern void __init at91_gpio_irq_setup(void);
+
+extern void (*at91_arch_reset)(void);
+extern int at91_extern_irq;
diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c
new file mode 100644
index 0000000..9b7495c
--- /dev/null
+++ b/arch/arm/mach-at91/gpio.c
@@ -0,0 +1,414 @@
+/*
+ * linux/arch/arm/mach-at91/gpio.c
+ *
+ * Copyright (C) 2005 HP Labs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+
+#include <asm/io.h>
+#include <asm/hardware.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static struct at91_gpio_bank *gpio;
+static int gpio_banks;
+
+
+static inline void __iomem *pin_to_controller(unsigned pin)
+{
+	void __iomem *sys_base = (void __iomem *) AT91_VA_BASE_SYS;
+
+	pin -= PIN_BASE;
+	pin /= 32;
+	if (likely(pin < gpio_banks))
+		return sys_base + gpio[pin].offset;
+
+	return NULL;
+}
+
+static inline unsigned pin_to_mask(unsigned pin)
+{
+	pin -= PIN_BASE;
+	return 1 << (pin % 32);
+}
+
+
+/*--------------------------------------------------------------------------*/
+
+/* Not all hardware capabilities are exposed through these calls; they
+ * only encapsulate the most common features and modes.  (So if you
+ * want to change signals in groups, do it directly.)
+ *
+ * Bootloaders will usually handle some of the pin multiplexing setup.
+ * The intent is certainly that by the time Linux is fully booted, all
+ * pins should have been fully initialized.  These setup calls should
+ * only be used by board setup routines, or possibly in driver probe().
+ *
+ * For bootloaders doing all that setup, these calls could be inlined
+ * as NOPs so Linux won't duplicate any setup code
+ */
+
+
+/*
+ * mux the pin to the "A" internal peripheral role.
+ */
+int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+
+	__raw_writel(mask, pio + PIO_IDR);
+	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+	__raw_writel(mask, pio + PIO_ASR);
+	__raw_writel(mask, pio + PIO_PDR);
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_A_periph);
+
+
+/*
+ * mux the pin to the "B" internal peripheral role.
+ */
+int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+
+	__raw_writel(mask, pio + PIO_IDR);
+	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+	__raw_writel(mask, pio + PIO_BSR);
+	__raw_writel(mask, pio + PIO_PDR);
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_B_periph);
+
+
+/*
+ * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and
+ * configure it for an input.
+ */
+int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+
+	__raw_writel(mask, pio + PIO_IDR);
+	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+	__raw_writel(mask, pio + PIO_ODR);
+	__raw_writel(mask, pio + PIO_PER);
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_gpio_input);
+
+
+/*
+ * mux the pin to the gpio controller (instead of "A" or "B" peripheral),
+ * and configure it for an output.
+ */
+int __init_or_module at91_set_gpio_output(unsigned pin, int value)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+
+	__raw_writel(mask, pio + PIO_IDR);
+	__raw_writel(mask, pio + PIO_PUDR);
+	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
+	__raw_writel(mask, pio + PIO_OER);
+	__raw_writel(mask, pio + PIO_PER);
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_gpio_output);
+
+
+/*
+ * enable/disable the glitch filter; mostly used with IRQ handling.
+ */
+int __init_or_module at91_set_deglitch(unsigned pin, int is_on)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+	__raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR));
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_deglitch);
+
+/*
+ * enable/disable the multi-driver; This is only valid for output and
+ * allows the output pin to run as an open collector output.
+ */
+int __init_or_module at91_set_multi_drive(unsigned pin, int is_on)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+
+	__raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR));
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_multi_drive);
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * assuming the pin is muxed as a gpio output, set its value.
+ */
+int at91_set_gpio_value(unsigned pin, int value)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (!pio)
+		return -EINVAL;
+	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
+	return 0;
+}
+EXPORT_SYMBOL(at91_set_gpio_value);
+
+
+/*
+ * read the pin's value (works even if it's not muxed as a gpio).
+ */
+int at91_get_gpio_value(unsigned pin)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+	u32		pdsr;
+
+	if (!pio)
+		return -EINVAL;
+	pdsr = __raw_readl(pio + PIO_PDSR);
+	return (pdsr & mask) != 0;
+}
+EXPORT_SYMBOL(at91_get_gpio_value);
+
+/*--------------------------------------------------------------------------*/
+
+#ifdef CONFIG_PM
+
+static u32 wakeups[MAX_GPIO_BANKS];
+static u32 backups[MAX_GPIO_BANKS];
+
+static int gpio_irq_set_wake(unsigned pin, unsigned state)
+{
+	unsigned	mask = pin_to_mask(pin);
+	unsigned	bank = (pin - PIN_BASE) / 32;
+
+	if (unlikely(bank >= MAX_GPIO_BANKS))
+		return -EINVAL;
+
+	if (state)
+		wakeups[bank] |= mask;
+	else
+		wakeups[bank] &= ~mask;
+
+	set_irq_wake(gpio[bank].id, state);
+
+	return 0;
+}
+
+void at91_gpio_suspend(void)
+{
+	int i;
+
+	for (i = 0; i < gpio_banks; i++) {
+		u32 pio = gpio[i].offset;
+
+		backups[i] = at91_sys_read(pio + PIO_IMR);
+		at91_sys_write(pio + PIO_IDR, backups[i]);
+		at91_sys_write(pio + PIO_IER, wakeups[i]);
+
+		if (!wakeups[i])
+			clk_disable(gpio[i].clock);
+		else {
+#ifdef CONFIG_PM_DEBUG
+			printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
+#endif
+		}
+	}
+}
+
+void at91_gpio_resume(void)
+{
+	int i;
+
+	for (i = 0; i < gpio_banks; i++) {
+		u32 pio = gpio[i].offset;
+
+		if (!wakeups[i])
+			clk_enable(gpio[i].clock);
+
+		at91_sys_write(pio + PIO_IDR, wakeups[i]);
+		at91_sys_write(pio + PIO_IER, backups[i]);
+	}
+}
+
+#else
+#define gpio_irq_set_wake	NULL
+#endif
+
+
+/* Several AIC controller irqs are dispatched through this GPIO handler.
+ * To use any AT91_PIN_* as an externally triggered IRQ, first call
+ * at91_set_gpio_input() then maybe enable its glitch filter.
+ * Then just request_irq() with the pin ID; it works like any ARM IRQ
+ * handler, though it always triggers on rising and falling edges.
+ *
+ * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after
+ * configuring them with at91_set_a_periph() or at91_set_b_periph().
+ * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering.
+ */
+
+static void gpio_irq_mask(unsigned pin)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (pio)
+		__raw_writel(mask, pio + PIO_IDR);
+}
+
+static void gpio_irq_unmask(unsigned pin)
+{
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
+
+	if (pio)
+		__raw_writel(mask, pio + PIO_IER);
+}
+
+static int gpio_irq_type(unsigned pin, unsigned type)
+{
+	return (type == IRQT_BOTHEDGE) ? 0 : -EINVAL;
+}
+
+static struct irq_chip gpio_irqchip = {
+	.name		= "GPIO",
+	.mask		= gpio_irq_mask,
+	.unmask		= gpio_irq_unmask,
+	.set_type	= gpio_irq_type,
+	.set_wake	= gpio_irq_set_wake,
+};
+
+static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
+{
+	unsigned	pin;
+	struct irq_desc	*gpio;
+	void __iomem	*pio;
+	u32		isr;
+
+	pio = get_irq_chip_data(irq);
+
+	/* temporarily mask (level sensitive) parent IRQ */
+	desc->chip->ack(irq);
+	for (;;) {
+		/* reading ISR acks the pending (edge triggered) GPIO interrupt */
+		isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR);
+		if (!isr)
+			break;
+
+		pin = (unsigned) get_irq_data(irq);
+		gpio = &irq_desc[pin];
+
+		while (isr) {
+			if (isr & 1) {
+				if (unlikely(gpio->depth)) {
+					/*
+					 * The core ARM interrupt handler lazily disables IRQs so
+					 * another IRQ must be generated before it actually gets
+					 * here to be disabled on the GPIO controller.
+					 */
+					gpio_irq_mask(pin);
+				}
+				else
+					desc_handle_irq(pin, gpio);
+			}
+			pin++;
+			gpio++;
+			isr >>= 1;
+		}
+	}
+	desc->chip->unmask(irq);
+	/* now it may re-trigger */
+}
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * Called from the processor-specific init to enable GPIO interrupt support.
+ */
+void __init at91_gpio_irq_setup(void)
+{
+	unsigned	pioc, pin;
+
+	for (pioc = 0, pin = PIN_BASE;
+			pioc < gpio_banks;
+			pioc++) {
+		void __iomem	*controller;
+		unsigned	id = gpio[pioc].id;
+		unsigned	i;
+
+		clk_enable(gpio[pioc].clock);	/* enable PIO controller's clock */
+
+		controller = (void __iomem *) AT91_VA_BASE_SYS + gpio[pioc].offset;
+		__raw_writel(~0, controller + PIO_IDR);
+
+		set_irq_data(id, (void *) pin);
+		set_irq_chip_data(id, controller);
+
+		for (i = 0; i < 32; i++, pin++) {
+			/*
+			 * Can use the "simple" and not "edge" handler since it's
+			 * shorter, and the AIC handles interupts sanely.
+			 */
+			set_irq_chip(pin, &gpio_irqchip);
+			set_irq_handler(pin, handle_simple_irq);
+			set_irq_flags(pin, IRQF_VALID);
+		}
+
+		set_irq_chained_handler(id, gpio_irq_handler);
+	}
+	pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
+}
+
+/*
+ * Called from the processor-specific init to enable GPIO pin support.
+ */
+void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
+{
+	BUG_ON(nr_banks > MAX_GPIO_BANKS);
+
+	gpio = data;
+	gpio_banks = nr_banks;
+}
diff --git a/arch/arm/mach-at91/irq.c b/arch/arm/mach-at91/irq.c
new file mode 100644
index 0000000..78a5cdb
--- /dev/null
+++ b/arch/arm/mach-at91/irq.c
@@ -0,0 +1,168 @@
+/*
+ * linux/arch/arm/mach-at91/irq.c
+ *
+ *  Copyright (C) 2004 SAN People
+ *  Copyright (C) 2004 ATMEL
+ *  Copyright (C) Rick Bronson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mm.h>
+#include <linux/types.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/setup.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+
+
+static void at91_aic_mask_irq(unsigned int irq)
+{
+	/* Disable interrupt on AIC */
+	at91_sys_write(AT91_AIC_IDCR, 1 << irq);
+}
+
+static void at91_aic_unmask_irq(unsigned int irq)
+{
+	/* Enable interrupt on AIC */
+	at91_sys_write(AT91_AIC_IECR, 1 << irq);
+}
+
+unsigned int at91_extern_irq;
+
+#define is_extern_irq(irq) ((1 << (irq)) & at91_extern_irq)
+
+static int at91_aic_set_type(unsigned irq, unsigned type)
+{
+	unsigned int smr, srctype;
+
+	switch (type) {
+	case IRQT_HIGH:
+		srctype = AT91_AIC_SRCTYPE_HIGH;
+		break;
+	case IRQT_RISING:
+		srctype = AT91_AIC_SRCTYPE_RISING;
+		break;
+	case IRQT_LOW:
+		if ((irq == AT91_ID_FIQ) || is_extern_irq(irq))		/* only supported on external interrupts */
+			srctype = AT91_AIC_SRCTYPE_LOW;
+		else
+			return -EINVAL;
+		break;
+	case IRQT_FALLING:
+		if ((irq == AT91_ID_FIQ) || is_extern_irq(irq))		/* only supported on external interrupts */
+			srctype = AT91_AIC_SRCTYPE_FALLING;
+		else
+			return -EINVAL;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	smr = at91_sys_read(AT91_AIC_SMR(irq)) & ~AT91_AIC_SRCTYPE;
+	at91_sys_write(AT91_AIC_SMR(irq), smr | srctype);
+	return 0;
+}
+
+#ifdef CONFIG_PM
+
+static u32 wakeups;
+static u32 backups;
+
+static int at91_aic_set_wake(unsigned irq, unsigned value)
+{
+	if (unlikely(irq >= 32))
+		return -EINVAL;
+
+	if (value)
+		wakeups |= (1 << irq);
+	else
+		wakeups &= ~(1 << irq);
+
+	return 0;
+}
+
+void at91_irq_suspend(void)
+{
+	backups = at91_sys_read(AT91_AIC_IMR);
+	at91_sys_write(AT91_AIC_IDCR, backups);
+	at91_sys_write(AT91_AIC_IECR, wakeups);
+}
+
+void at91_irq_resume(void)
+{
+	at91_sys_write(AT91_AIC_IDCR, wakeups);
+	at91_sys_write(AT91_AIC_IECR, backups);
+}
+
+#else
+#define at91_aic_set_wake	NULL
+#endif
+
+static struct irq_chip at91_aic_chip = {
+	.name		= "AIC",
+	.ack		= at91_aic_mask_irq,
+	.mask		= at91_aic_mask_irq,
+	.unmask		= at91_aic_unmask_irq,
+	.set_type	= at91_aic_set_type,
+	.set_wake	= at91_aic_set_wake,
+};
+
+/*
+ * Initialize the AIC interrupt controller.
+ */
+void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS])
+{
+	unsigned int i;
+
+	/*
+	 * The IVR is used by macro get_irqnr_and_base to read and verify.
+	 * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred.
+	 */
+	for (i = 0; i < NR_AIC_IRQS; i++) {
+		/* Put irq number in Source Vector Register: */
+		at91_sys_write(AT91_AIC_SVR(i), i);
+		/* Active Low interrupt, with the specified priority */
+		at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
+
+		set_irq_chip(i, &at91_aic_chip);
+		set_irq_handler(i, handle_level_irq);
+		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+
+		/* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */
+		if (i < 8)
+			at91_sys_write(AT91_AIC_EOICR, 0);
+	}
+
+	/*
+	 * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS
+	 * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU
+	 */
+	at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS);
+
+	/* No debugging in AIC: Debug (Protect) Control Register */
+	at91_sys_write(AT91_AIC_DCR, 0);
+
+	/* Disable and clear all interrupts initially */
+	at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF);
+	at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF);
+}
diff --git a/arch/arm/mach-at91/leds.c b/arch/arm/mach-at91/leds.c
new file mode 100644
index 0000000..1a33373
--- /dev/null
+++ b/arch/arm/mach-at91/leds.c
@@ -0,0 +1,99 @@
+/*
+ * LED driver for Atmel AT91-based boards.
+ *
+ *  Copyright (C) SAN People (Pty) Ltd
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+
+#include <asm/mach-types.h>
+#include <asm/leds.h>
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+
+static inline void at91_led_on(unsigned int led)
+{
+	at91_set_gpio_value(led, 0);
+}
+
+static inline void at91_led_off(unsigned int led)
+{
+	at91_set_gpio_value(led, 1);
+}
+
+static inline void at91_led_toggle(unsigned int led)
+{
+	unsigned long is_off = at91_get_gpio_value(led);
+	if (is_off)
+		at91_led_on(led);
+	else
+		at91_led_off(led);
+}
+
+
+/*
+ * Handle LED events.
+ */
+static void at91_leds_event(led_event_t evt)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	switch(evt) {
+	case led_start:		/* System startup */
+		at91_led_on(at91_leds_cpu);
+		break;
+
+	case led_stop:		/* System stop / suspend */
+		at91_led_off(at91_leds_cpu);
+		break;
+
+#ifdef CONFIG_LEDS_TIMER
+	case led_timer:		/* Every 50 timer ticks */
+		at91_led_toggle(at91_leds_timer);
+		break;
+#endif
+
+#ifdef CONFIG_LEDS_CPU
+	case led_idle_start:	/* Entering idle state */
+		at91_led_off(at91_leds_cpu);
+		break;
+
+	case led_idle_end:	/* Exit idle state */
+		at91_led_on(at91_leds_cpu);
+		break;
+#endif
+
+	default:
+		break;
+	}
+
+	local_irq_restore(flags);
+}
+
+
+static int __init leds_init(void)
+{
+	if (!at91_leds_timer || !at91_leds_cpu)
+		return -ENODEV;
+
+	/* Enable PIO to access the LEDs */
+	at91_set_gpio_output(at91_leds_timer, 1);
+	at91_set_gpio_output(at91_leds_cpu, 1);
+
+	leds_event = at91_leds_event;
+
+	leds_event(led_start);
+	return 0;
+}
+
+__initcall(leds_init);
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
new file mode 100644
index 0000000..e095b1f
--- /dev/null
+++ b/arch/arm/mach-at91/pm.c
@@ -0,0 +1,227 @@
+/*
+ * arch/arm/mach-at91/pm.c
+ * AT91 Power Management
+ *
+ * Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/pm.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/sysfs.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/atomic.h>
+#include <asm/mach/time.h>
+#include <asm/mach/irq.h>
+#include <asm/mach-types.h>
+
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91rm9200_mc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/cpu.h>
+
+#include "generic.h"
+
+
+static int at91_pm_valid_state(suspend_state_t state)
+{
+	switch (state) {
+		case PM_SUSPEND_ON:
+		case PM_SUSPEND_STANDBY:
+		case PM_SUSPEND_MEM:
+			return 1;
+
+		default:
+			return 0;
+	}
+}
+
+
+static suspend_state_t target_state;
+
+/*
+ * Called after processes are frozen, but before we shutdown devices.
+ */
+static int at91_pm_prepare(suspend_state_t state)
+{
+	target_state = state;
+	return 0;
+}
+
+/*
+ * Verify that all the clocks are correct before entering
+ * slow-clock mode.
+ */
+static int at91_pm_verify_clocks(void)
+{
+	unsigned long scsr;
+	int i;
+
+	scsr = at91_sys_read(AT91_PMC_SCSR);
+
+	/* USB must not be using PLLB */
+	if (cpu_is_at91rm9200()) {
+		if ((scsr & (AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP)) != 0) {
+			pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
+			return 0;
+		}
+	} else if (cpu_is_at91sam9260()) {
+#warning "Check SAM9260 USB clocks"
+	} else if (cpu_is_at91sam9261()) {
+#warning "Check SAM9261 USB clocks"
+	}
+
+#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
+	/* PCK0..PCK3 must be disabled, or configured to use clk32k */
+	for (i = 0; i < 4; i++) {
+		u32 css;
+
+		if ((scsr & (AT91_PMC_PCK0 << i)) == 0)
+			continue;
+
+		css = at91_sys_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS;
+		if (css != AT91_PMC_CSS_SLOW) {
+			pr_debug("AT91: PM - Suspend-to-RAM with PCK%d src %d\n", i, css);
+			return 0;
+		}
+	}
+#endif
+
+	return 1;
+}
+
+/*
+ * Call this from platform driver suspend() to see how deeply to suspend.
+ * For example, some controllers (like OHCI) need one of the PLL clocks
+ * in order to act as a wakeup source, and those are not available when
+ * going into slow clock mode.
+ *
+ * REVISIT: generalize as clk_will_be_available(clk)?  Other platforms have
+ * the very same problem (but not using at91 main_clk), and it'd be better
+ * to add one generic API rather than lots of platform-specific ones.
+ */
+int at91_suspend_entering_slow_clock(void)
+{
+	return (target_state == PM_SUSPEND_MEM);
+}
+EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
+
+
+static void (*slow_clock)(void);
+
+
+static int at91_pm_enter(suspend_state_t state)
+{
+	at91_gpio_suspend();
+	at91_irq_suspend();
+
+	pr_debug("AT91: PM - wake mask %08x, pm state %d\n",
+			/* remember all the always-wake irqs */
+			(at91_sys_read(AT91_PMC_PCSR)
+					| (1 << AT91_ID_FIQ)
+					| (1 << AT91_ID_SYS)
+					| (at91_extern_irq))
+				& at91_sys_read(AT91_AIC_IMR),
+			state);
+
+	switch (state) {
+		/*
+		 * Suspend-to-RAM is like STANDBY plus slow clock mode, so
+		 * drivers must suspend more deeply:  only the master clock
+		 * controller may be using the main oscillator.
+		 */
+		case PM_SUSPEND_MEM:
+			/*
+			 * Ensure that clocks are in a valid state.
+			 */
+			if (!at91_pm_verify_clocks())
+				goto error;
+
+			/*
+			 * Enter slow clock mode by switching over to clk32k and
+			 * turning off the main oscillator; reverse on wakeup.
+			 */
+			if (slow_clock) {
+				slow_clock();
+				break;
+			} else {
+				/* DEVELOPMENT ONLY */
+				pr_info("AT91: PM - no slow clock mode yet ...\n");
+				/* FALLTHROUGH leaving master clock alone */
+			}
+
+		/*
+		 * STANDBY mode has *all* drivers suspended; ignores irqs not
+		 * marked as 'wakeup' event sources; and reduces DRAM power.
+		 * But otherwise it's identical to PM_SUSPEND_ON:  cpu idle, and
+		 * nothing fancy done with main or cpu clocks.
+		 */
+		case PM_SUSPEND_STANDBY:
+			/*
+			 * NOTE: the Wait-for-Interrupt instruction needs to be
+			 * in icache so the SDRAM stays in self-refresh mode until
+			 * the wakeup IRQ occurs.
+			 */
+			asm("b 1f; .align 5; 1:");
+			asm("mcr p15, 0, r0, c7, c10, 4");	/* drain write buffer */
+			at91_sys_write(AT91_SDRAMC_SRR, 1);	/* self-refresh mode */
+			/* fall though to next state */
+
+		case PM_SUSPEND_ON:
+			asm("mcr p15, 0, r0, c7, c0, 4");	/* wait for interrupt */
+			break;
+
+		default:
+			pr_debug("AT91: PM - bogus suspend state %d\n", state);
+			goto error;
+	}
+
+	pr_debug("AT91: PM - wakeup %08x\n",
+			at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR));
+
+error:
+	target_state = PM_SUSPEND_ON;
+	at91_irq_resume();
+	at91_gpio_resume();
+	return 0;
+}
+
+
+static struct pm_ops at91_pm_ops ={
+	.pm_disk_mode	= 0,
+	.valid		= at91_pm_valid_state,
+	.prepare	= at91_pm_prepare,
+	.enter		= at91_pm_enter,
+};
+
+static int __init at91_pm_init(void)
+{
+	printk("AT91: Power Management\n");
+
+#ifdef CONFIG_AT91_PM_SLOW_CLOCK
+	/* REVISIT allocations of SRAM should be dynamically managed.
+	 * FIQ handlers and other components will want SRAM/TCM too...
+	 */
+	slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K));
+	memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz);
+#endif
+
+	/* Disable SDRAM low-power mode.  Cannot be used with self-refresh. */
+	at91_sys_write(AT91_SDRAMC_LPR, 0);
+
+	pm_set_ops(&at91_pm_ops);
+
+	return 0;
+}
+arch_initcall(at91_pm_init);