mtd: denali: detect the number of banks

Not all configurations of the Denali controller support 4 banks.  The
controller can support between 1 and 16 banks.  Detect this from the
design features register.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

1 files changed, 20 insertions, 8 deletions

diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 5568640..8c5dc89 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -178,11 +178,11 @@ static uint16_t denali_nand_reset(struct denali_nand_info *denali)
 	dev_dbg(denali->dev, "%s, Line %d, Function: %s\n",
 		       __FILE__, __LINE__, __func__);
 
-	for (i = 0 ; i < LLD_MAX_FLASH_BANKS; i++)
+	for (i = 0 ; i < denali->max_banks; i++)
 		iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
 		denali->flash_reg + INTR_STATUS(i));
 
-	for (i = 0 ; i < LLD_MAX_FLASH_BANKS; i++) {
+	for (i = 0 ; i < denali->max_banks; i++) {
 		iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
 		while (!(ioread32(denali->flash_reg +
 				INTR_STATUS(i)) &
@@ -194,7 +194,7 @@ static uint16_t denali_nand_reset(struct denali_nand_info *denali)
 			"NAND Reset operation timed out on bank %d\n", i);
 	}
 
-	for (i = 0; i < LLD_MAX_FLASH_BANKS; i++)
+	for (i = 0; i < denali->max_banks; i++)
 		iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
 			denali->flash_reg + INTR_STATUS(i));
 
@@ -405,11 +405,11 @@ static void get_hynix_nand_para(struct denali_nand_info *denali,
  */
 static void find_valid_banks(struct denali_nand_info *denali)
 {
-	uint32_t id[LLD_MAX_FLASH_BANKS];
+	uint32_t id[denali->max_banks];
 	int i;
 
 	denali->total_used_banks = 1;
-	for (i = 0; i < LLD_MAX_FLASH_BANKS; i++) {
+	for (i = 0; i < denali->max_banks; i++) {
 		index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 0), 0x90);
 		index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 1), 0);
 		index_addr_read_data(denali,
@@ -445,6 +445,17 @@ static void find_valid_banks(struct denali_nand_info *denali)
 		"denali->total_used_banks: %d\n", denali->total_used_banks);
 }
 
+/*
+ * Use the configuration feature register to determine the maximum number of
+ * banks that the hardware supports.
+ */
+static void detect_max_banks(struct denali_nand_info *denali)
+{
+	uint32_t features = ioread32(denali->flash_reg + FEATURES);
+
+	denali->max_banks = 2 << (features & FEATURES__N_BANKS);
+}
+
 static void detect_partition_feature(struct denali_nand_info *denali)
 {
 	/* For MRST platform, denali->fwblks represent the
@@ -562,7 +573,7 @@ static void denali_irq_init(struct denali_nand_info *denali)
 	int_mask = DENALI_IRQ_ALL;
 
 	/* Clear all status bits */
-	for (i = 0; i < LLD_MAX_FLASH_BANKS; ++i)
+	for (i = 0; i < denali->max_banks; ++i)
 		iowrite32(0xFFFF, denali->flash_reg + INTR_STATUS(i));
 
 	denali_irq_enable(denali, int_mask);
@@ -579,7 +590,7 @@ static void denali_irq_enable(struct denali_nand_info *denali,
 {
 	int i;
 
-	for (i = 0; i < LLD_MAX_FLASH_BANKS; ++i)
+	for (i = 0; i < denali->max_banks; ++i)
 		iowrite32(int_mask, denali->flash_reg + INTR_EN(i));
 }
 
@@ -1345,6 +1356,7 @@ static void denali_hw_init(struct denali_nand_info *denali)
 	/* Should set value for these registers when init */
 	iowrite32(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES);
 	iowrite32(1, denali->flash_reg + ECC_ENABLE);
+	detect_max_banks(denali);
 	denali_nand_timing_set(denali);
 	denali_irq_init(denali);
 }
@@ -1522,7 +1534,7 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	/* scan for NAND devices attached to the controller
 	 * this is the first stage in a two step process to register
 	 * with the nand subsystem */
-	if (nand_scan_ident(&denali->mtd, LLD_MAX_FLASH_BANKS, NULL)) {
+	if (nand_scan_ident(&denali->mtd, denali->max_banks, NULL)) {
 		ret = -ENXIO;
 		goto failed_req_irq;
 	}