diff options
| -rw-r--r-- | drivers/gpu/drm/i915/intel_drv.h | 2 | ||||
| -rw-r--r-- | drivers/gpu/drm/i915/intel_i2c.c | 25 | ||||
| -rw-r--r-- | drivers/gpu/drm/i915/intel_lvds.c | 10 |
3 files changed, 24 insertions, 13 deletions
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h index 5daa991..f5b0d83 100644 --- a/drivers/gpu/drm/i915/intel_drv.h +++ b/drivers/gpu/drm/i915/intel_drv.h @@ -39,7 +39,7 @@ ret__ = -ETIMEDOUT; \ break; \ } \ - if (W && !in_dbg_master()) msleep(W); \ + if (W && !(in_atomic() || in_dbg_master())) msleep(W); \ } \ ret__; \ }) diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c index 82d04c5..d3b903b 100644 --- a/drivers/gpu/drm/i915/intel_i2c.c +++ b/drivers/gpu/drm/i915/intel_i2c.c @@ -259,7 +259,7 @@ gmbus_xfer(struct i2c_adapter *adapter, if (wait_for(I915_READ(GMBUS2 + reg_offset) & (GMBUS_SATOER | GMBUS_HW_RDY), 50)) goto timeout; if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER) - return 0; + goto clear_err; val = I915_READ(GMBUS3 + reg_offset); do { @@ -287,7 +287,7 @@ gmbus_xfer(struct i2c_adapter *adapter, if (wait_for(I915_READ(GMBUS2 + reg_offset) & (GMBUS_SATOER | GMBUS_HW_RDY), 50)) goto timeout; if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER) - return 0; + goto clear_err; val = loop = 0; do { @@ -302,14 +302,31 @@ gmbus_xfer(struct i2c_adapter *adapter, if (i + 1 < num && wait_for(I915_READ(GMBUS2 + reg_offset) & (GMBUS_SATOER | GMBUS_HW_WAIT_PHASE), 50)) goto timeout; if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER) - return 0; + goto clear_err; } - return num; + goto done; + +clear_err: + /* Toggle the Software Clear Interrupt bit. This has the effect + * of resetting the GMBUS controller and so clearing the + * BUS_ERROR raised by the slave's NAK. + */ + I915_WRITE(GMBUS1 + reg_offset, GMBUS_SW_CLR_INT); + I915_WRITE(GMBUS1 + reg_offset, 0); + +done: + /* Mark the GMBUS interface as disabled. We will re-enable it at the + * start of the next xfer, till then let it sleep. + */ + I915_WRITE(GMBUS0 + reg_offset, 0); + return i; timeout: DRM_INFO("GMBUS timed out, falling back to bit banging on pin %d [%s]\n", bus->reg0 & 0xff, bus->adapter.name); + I915_WRITE(GMBUS0 + reg_offset, 0); + /* Hardware may not support GMBUS over these pins? Try GPIO bitbanging instead. */ bus->force_bit = intel_gpio_create(dev_priv, bus->reg0 & 0xff); if (!bus->force_bit) diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c index 1a311ad..86cd30b 100644 --- a/drivers/gpu/drm/i915/intel_lvds.c +++ b/drivers/gpu/drm/i915/intel_lvds.c @@ -473,19 +473,13 @@ static enum drm_connector_status intel_lvds_detect(struct drm_connector *connector, bool force) { struct drm_device *dev = connector->dev; - enum drm_connector_status status = connector_status_connected; + enum drm_connector_status status; status = intel_panel_detect(dev); if (status != connector_status_unknown) return status; - /* ACPI lid methods were generally unreliable in this generation, so - * don't even bother. - */ - if (IS_GEN2(dev) || IS_GEN3(dev)) - return connector_status_connected; - - return status; + return connector_status_connected; } /** |