remove the documentation for the legacy CDROM drivers

This patch removes the documentation for the removed legacy CDROM drivers.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

1 files changed, 0 insertions, 196 deletions

diff --git a/Documentation/cdrom/cdu31a b/Documentation/cdrom/cdu31a
deleted file mode 100644
index c0667da..0000000
--- a/Documentation/cdrom/cdu31a
+++ /dev/null
@@ -1,196 +0,0 @@
-
-		CDU31A/CDU33A Driver Info
-		-------------------------
-
-Information on the Sony CDU31A/CDU33A CDROM driver for the Linux
-kernel.
-
-   Corey Minyard (minyard@metronet.com)
-  
-   Colossians 3:17
-
-Crude Table of Contents
------------------------
-
-  Setting Up the Hardware
-  Configuring the Kernel
-  Configuring as a Module
-  Driver Special Features
-
-  
-This device driver handles Sony CDU31A/CDU33A CDROM drives and
-provides a complete block-level interface as well as an ioctl()
-interface as specified in include/linux/cdrom.h).  With this
-interface, CDROMs can be accessed, standard audio CDs can be played
-back normally, and CD audio information can be read off the drive.
-
-Note that this will only work for CDU31A/CDU33A drives.  Some vendors
-market their drives as CDU31A compatible.  They lie.  Their drives are
-really CDU31A hardware interface compatible (they can plug into the
-same card).  They are not software compatible.
-
-Setting Up the Hardware
------------------------
-
-The CDU31A driver is unable to safely tell if an interface card is
-present that it can use because the interface card does not announce
-its presence in any way besides placing 4 I/O locations in memory.  It
-used to just probe memory and attempt commands, but Linus wisely asked
-me to remove that because it could really screw up other hardware in
-the system.
-
-Because of this, you must tell the kernel where the drive interface
-is, what interrupts are used, and possibly if you are on a PAS-16
-soundcard.
-
-If you have the Sony CDU31A/CDU33A drive interface card, the following
-diagram will help you set it up.  If you have another card, you are on
-your own.  You need to make sure that the I/O address and interrupt is
-not used by another card in the system.  You will need to know the I/O
-address and interrupt you have set.  Note that use of interrupts is
-highly recommended, if possible, it really cuts down on CPU used.
-Unfortunately, most soundcards do not support interrupts for their
-CDROM interfaces.  By default, the Sony interface card comes with
-interrupts disabled.
-   
-        +----------+-----------------+----------------------+
-        |  JP1     |  34 Pin Conn    |                      |
-        |  JP2     +-----------------+                      |
-        |  JP3                                              |
-        |  JP4                                              |
-        |                                                   +--+
-        |                                                   |  +-+
-        |                                                   |  | |  External
-        |                                                   |  | |  Connector
-        |                                                   |  | |
-        |                                                   |  +-+
-        |                                                   +--+
-        |                                                   |
-        |                                          +--------+
-        |                                          |
-        +------------------------------------------+
-   
-      JP1 sets the Base Address, using the following settings:
-   
-        Address         Pin 1           Pin 2
-        -------         -----           -----
-        0x320           Short           Short
-        0x330           Short           Open
-        0x340           Open            Short
-        0x360           Open            Open
-   
-      JP2 and JP3 configure the DMA channel; they must be set the same.
-   
-        DMA             Pin 1           Pin 2           Pin 3
-        ---             -----           -----           -----
-        1               On              Off             On
-        2               Off             On              Off
-        3               Off             Off             On
-   
-      JP4 Configures the IRQ:
-   
-        IRQ     Pin 1           Pin 2           Pin 3           Pin 4
-        ---     -----           -----           -----           -----
-        3       Off             Off             On              Off
-        4       Off             Off*            Off             On
-        5       On              Off             Off             Off
-        6       Off             On              Off             Off
-   
-                  The documentation states to set this for interrupt
-                  4, but I think that is a mistake.
-
-Note that if you have another interface card, you will need to look at
-the documentation to find the I/O base address.  This is specified to
-the SLCD.SYS driver for DOS with the /B: parameter, so you can look at
-you DOS driver setup to find the address, if necessary.
-
-Configuring the Kernel
-----------------------
-
-You must tell the kernel where the drive is at boot time.  This can be
-done at the Linux boot prompt, by using LILO, or by using Bootlin.
-Note that this is no substitute for HOWTOs and LILO documentation, if
-you are confused please read those for info on bootline configuration
-and LILO.
-
-At the linux boot prompt, press the ALT key and add the following line
-after the boot name (you can let the kernel boot, it will tell you the
-default boot name while booting):
-
-	cdu31a=<base address>,<interrupt>[,PAS]
-
-The base address needs to have "0x" in front of it, since it is in
-hex.  For instance, to configure a drive at address 320 on interrupt 5,
-use the following:
-
-	cdu31a=0x320,5
-
-I use the following boot line:
-
-	cdu31a=0x1f88,0,PAS
-
-because I have a PAS-16 which does not support interrupt for the
-CDU31A interface.
-
-Adding this as an append line at the beginning of the /etc/lilo.conf
-file will set it for lilo configurations.  I have the following as the
-first line in my lilo.conf file:
-
-	append="cdu31a=0x1f88,0"
-
-I'm not sure how to set up Bootlin (I have never used it), if someone
-would like to fill in this section please do.
-
-
-Configuring as a Module
------------------------
-
-The driver supports loading as a module.  However, you must specify
-the boot address and interrupt on the boot line to insmod.  You can't
-use modprobe to load it, since modprobe doesn't support setting
-variables.
-
-Anyway, I use the following line to load my driver as a module
-
-  /sbin/insmod /lib/modules/`uname -r`/misc/cdu31a.o cdu31a_port=0x1f88
-
-You can set the following variables in the driver:
-
-  cdu31a_port=<I/O address> - sets the base I/O.  If hex, put 0x in
-			      front of it.  This must be specified.
-
-  cdu31a_irq=<interrupt> - Sets the interrupt number.  Leaving this
-			   off will turn interrupts off.
-
-
-Driver Special Features
------------------------
-
-This section describes features beyond the normal audio and CD-ROM
-functions of the drive.
-
-2048 byte buffer mode
-
-If a disk is mounted with -o block=2048, data is copied straight from
-the drive data port to the buffer.  Otherwise, the readahead buffer
-must be involved to hold the other 1K of data when a 1K block
-operation is done.  Note that with 2048 byte blocks you cannot execute
-files from the CD.
-
-XA compatibility
-
-The driver should support XA disks for both the CDU31A and CDU33A.  It
-does this transparently, the using program doesn't need to set it.
-
-Multi-Session
-
-A multi-session disk looks just like a normal disk to the user.  Just
-mount one normally, and all the data should be there.  A special
-thanks to Koen for help with this!
-
-Raw sector I/O
-
-Using the CDROMREADAUDIO it is possible to read raw audio and data
-tracks.  Both operations return 2352 bytes per sector.  On the data
-tracks, the first 12 bytes is not returned by the drive and the value
-of that data is indeterminate.