Merge branch 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6

* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
  IXP4xx: Fix LL debugging on little-endian CPU.
  IXP4xx: Fix sparse warnings in I/O primitives.
  IXP4xx: Make mdio_bus struct static in the Ethernet driver.
  IXP4xx: Fix ixp4xx_crypto little-endian operation.
  IXP4xx: Prevent HSS transmitter lockup by disabling FRaMe signals.
  ixp4xx/vulcan: add PCI support
  ixp4xx: base support for Arcom Vulcan

6 files changed, 334 insertions, 3 deletions

diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 9e5070d..6f991c5 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -140,6 +140,14 @@ config MACH_FSG
 	  FSG-3 device. For more information on this platform,
 	  see http://www.nslu2-linux.org/wiki/FSG3/HomePage
 
+config MACH_ARCOM_VULCAN
+	bool
+	prompt "Arcom/Eurotech Vulcan"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support Arcom's
+	  Vulcan board.
+
 #
 # Certain registers and IRQs are only enabled if supporting IXP465 CPUs
 #
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
index 47d1f60..d807fc3 100644
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -16,6 +16,7 @@ obj-pci-$(CONFIG_MACH_DSMG600)		+= dsmg600-pci.o
 obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-pci.o
 obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
 obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+obj-pci-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-pci.o
 
 obj-y	+= common.o
 
@@ -31,6 +32,7 @@ obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
 obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
 obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
 obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_mlr.o
+obj-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-setup.o
 
 obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
 obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
diff --git a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
index 893873e..3fc66d6 100644
--- a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
@@ -16,8 +16,10 @@
                 moveq   \rx, #0xc8000000
                 movne   \rx, #0xff000000
 		orrne	\rx, \rx, #0x00b00000
+#ifdef __ARMEB__
                 add     \rx,\rx,#3              @ Uart regs are at off set of 3 if
 						@ byte writes used - Big Endian.
+#endif
                 .endm
 
 #define UART_SHIFT	2
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index 6ea7e2f..de274a1 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -353,7 +353,7 @@ static inline unsigned int ioread8(const void __iomem *addr)
 		return (unsigned int)inb(port & PIO_MASK);
 	else
 #ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		return (unsigned int)__raw_readb(port);
+		return (unsigned int)__raw_readb(addr);
 #else
 		return (unsigned int)__indirect_readb(addr);
 #endif
@@ -381,7 +381,7 @@ static inline unsigned int ioread16(const void __iomem *addr)
 		return	(unsigned int)inw(port & PIO_MASK);
 	else
 #ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		return le16_to_cpu(__raw_readw((u32)port));
+		return le16_to_cpu((__force __le16)__raw_readw(addr));
 #else
 		return (unsigned int)__indirect_readw(addr);
 #endif
@@ -440,7 +440,7 @@ static inline void iowrite8(u8 value, void __iomem *addr)
 		outb(value, port & PIO_MASK);
 	else
 #ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writeb(value, port);
+		__raw_writeb(value, addr);
 #else
 		__indirect_writeb(value, addr);
 #endif
diff --git a/arch/arm/mach-ixp4xx/vulcan-pci.c b/arch/arm/mach-ixp4xx/vulcan-pci.c
new file mode 100644
index 0000000..f3111c6
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/vulcan-pci.c
@@ -0,0 +1,73 @@
+/*
+ * arch/arch/mach-ixp4xx/vulcan-pci.c
+ *
+ * Vulcan board-level PCI initialization
+ *
+ * Copyright (C) 2010 Marc Zyngier <maz@misterjones.org>
+ *
+ * based on ixdp425-pci.c:
+ *	Copyright (C) 2002 Intel Corporation.
+ *	Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <asm/mach/pci.h>
+#include <asm/mach-types.h>
+
+/* PCI controller GPIO to IRQ pin mappings */
+#define INTA	2
+#define INTB	3
+
+void __init vulcan_pci_preinit(void)
+{
+#ifndef CONFIG_IXP4XX_INDIRECT_PCI
+	/*
+	 * Cardbus bridge wants way more than the SoC can actually offer,
+	 * and leaves the whole PCI bus in a mess. Artificially limit it
+	 * to 8MB per region. Of course indirect mode doesn't have this
+	 * limitation...
+	 */
+	pci_cardbus_mem_size = SZ_8M;
+	pr_info("Vulcan PCI: limiting CardBus memory size to %dMB\n",
+		(int)(pci_cardbus_mem_size >> 20));
+#endif
+	set_irq_type(IXP4XX_GPIO_IRQ(INTA), IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IXP4XX_GPIO_IRQ(INTB), IRQ_TYPE_LEVEL_LOW);
+	ixp4xx_pci_preinit();
+}
+
+static int __init vulcan_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 1)
+		return IXP4XX_GPIO_IRQ(INTA);
+
+	if (slot == 2)
+		return IXP4XX_GPIO_IRQ(INTB);
+
+	return -1;
+}
+
+struct hw_pci vulcan_pci __initdata = {
+	.nr_controllers	= 1,
+	.preinit	= vulcan_pci_preinit,
+	.swizzle	= pci_std_swizzle,
+	.setup		= ixp4xx_setup,
+	.scan		= ixp4xx_scan_bus,
+	.map_irq	= vulcan_map_irq,
+};
+
+int __init vulcan_pci_init(void)
+{
+	if (machine_is_arcom_vulcan())
+		pci_common_init(&vulcan_pci);
+	return 0;
+}
+
+subsys_initcall(vulcan_pci_init);
diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c
new file mode 100644
index 0000000..465cc5c
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/vulcan-setup.c
@@ -0,0 +1,246 @@
+/*
+ * arch/arm/mach-ixp4xx/vulcan-setup.c
+ *
+ * Arcom/Eurotech Vulcan board-setup
+ *
+ * Copyright (C) 2010 Marc Zyngier <maz@misterjones.org>
+ *
+ * based on fsg-setup.c:
+ *	Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ */
+
+#include <linux/if_ether.h>
+#include <linux/irq.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/io.h>
+#include <linux/w1-gpio.h>
+#include <linux/mtd/plat-ram.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data vulcan_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource vulcan_flash_resource = {
+	.flags			= IORESOURCE_MEM,
+};
+
+static struct platform_device vulcan_flash = {
+	.name			= "IXP4XX-Flash",
+	.id			= 0,
+	.dev = {
+		.platform_data	= &vulcan_flash_data,
+	},
+	.resource		= &vulcan_flash_resource,
+	.num_resources		= 1,
+};
+
+static struct platdata_mtd_ram vulcan_sram_data = {
+	.mapname	= "Vulcan SRAM",
+	.bankwidth	= 1,
+};
+
+static struct resource vulcan_sram_resource = {
+	.flags			= IORESOURCE_MEM,
+};
+
+static struct platform_device vulcan_sram = {
+	.name			= "mtd-ram",
+	.id			= 0,
+	.dev = {
+		.platform_data	= &vulcan_sram_data,
+	},
+	.resource		= &vulcan_sram_resource,
+	.num_resources		= 1,
+};
+
+static struct resource vulcan_uart_resources[] = {
+	[0] = {
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM,
+	},
+	[2] = {
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct plat_serial8250_port vulcan_uart_data[] = {
+	[0] = {
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	[1] = {
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	[2] = {
+		.irq		= IXP4XX_GPIO_IRQ(4),
+		.irqflags	= IRQF_TRIGGER_LOW,
+		.flags		= UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.uartclk	= 1843200,
+	},
+	[3] = {
+		.irq		= IXP4XX_GPIO_IRQ(4),
+		.irqflags	= IRQF_TRIGGER_LOW,
+		.flags		= UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.uartclk	= 1843200,
+	},
+	{ }
+};
+
+static struct platform_device vulcan_uart = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev = {
+		.platform_data	= vulcan_uart_data,
+	},
+	.resource		= vulcan_uart_resources,
+	.num_resources		= ARRAY_SIZE(vulcan_uart_resources),
+};
+
+static struct eth_plat_info vulcan_plat_eth[] = {
+	[0] = {
+		.phy		= 0,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	},
+	[1] = {
+		.phy		= 1,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	},
+};
+
+static struct platform_device vulcan_eth[] = {
+	[0] = {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev = {
+			.platform_data	= &vulcan_plat_eth[0],
+		},
+	},
+	[1] = {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev = {
+			.platform_data	= &vulcan_plat_eth[1],
+		},
+	},
+};
+
+static struct resource vulcan_max6369_resource = {
+	.flags			= IORESOURCE_MEM,
+};
+
+static struct platform_device vulcan_max6369 = {
+	.name			= "max6369_wdt",
+	.id			= -1,
+	.resource		= &vulcan_max6369_resource,
+	.num_resources		= 1,
+};
+
+static struct w1_gpio_platform_data vulcan_w1_gpio_pdata = {
+	.pin			= 14,
+};
+
+static struct platform_device vulcan_w1_gpio = {
+	.name			= "w1-gpio",
+	.id			= 0,
+	.dev			= {
+		.platform_data	= &vulcan_w1_gpio_pdata,
+	},
+};
+
+static struct platform_device *vulcan_devices[] __initdata = {
+	&vulcan_uart,
+	&vulcan_flash,
+	&vulcan_sram,
+	&vulcan_max6369,
+	&vulcan_eth[0],
+	&vulcan_eth[1],
+	&vulcan_w1_gpio,
+};
+
+static void __init vulcan_init(void)
+{
+	ixp4xx_sys_init();
+
+	/* Flash is spread over both CS0 and CS1 */
+	vulcan_flash_resource.start	 = IXP4XX_EXP_BUS_BASE(0);
+	vulcan_flash_resource.end	 = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+	*IXP4XX_EXP_CS0 = IXP4XX_EXP_BUS_CS_EN		|
+			  IXP4XX_EXP_BUS_STROBE_T(3)	|
+			  IXP4XX_EXP_BUS_SIZE(0xF)	|
+			  IXP4XX_EXP_BUS_BYTE_RD16	|
+			  IXP4XX_EXP_BUS_WR_EN;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	/* SRAM on CS2, (256kB, 8bit, writable) */
+	vulcan_sram_resource.start	= IXP4XX_EXP_BUS_BASE(2);
+	vulcan_sram_resource.end	= IXP4XX_EXP_BUS_BASE(2) + SZ_256K - 1;
+	*IXP4XX_EXP_CS2 = IXP4XX_EXP_BUS_CS_EN		|
+			  IXP4XX_EXP_BUS_STROBE_T(1)	|
+			  IXP4XX_EXP_BUS_HOLD_T(2)	|
+			  IXP4XX_EXP_BUS_SIZE(9)	|
+			  IXP4XX_EXP_BUS_SPLT_EN	|
+			  IXP4XX_EXP_BUS_WR_EN		|
+			  IXP4XX_EXP_BUS_BYTE_EN;
+
+	/* XR16L2551 on CS3 (Moto style, 512 bytes, 8bits, writable) */
+	vulcan_uart_resources[2].start	= IXP4XX_EXP_BUS_BASE(3);
+	vulcan_uart_resources[2].end	= IXP4XX_EXP_BUS_BASE(3) + 16 - 1;
+	vulcan_uart_data[2].mapbase	= vulcan_uart_resources[2].start;
+	vulcan_uart_data[3].mapbase	= vulcan_uart_data[2].mapbase + 8;
+	*IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN		|
+			  IXP4XX_EXP_BUS_STROBE_T(3)	|
+			  IXP4XX_EXP_BUS_CYCLES(IXP4XX_EXP_BUS_CYCLES_MOTOROLA)|
+			  IXP4XX_EXP_BUS_WR_EN		|
+			  IXP4XX_EXP_BUS_BYTE_EN;
+
+	/* GPIOS on CS4 (512 bytes, 8bits, writable) */
+	*IXP4XX_EXP_CS4 = IXP4XX_EXP_BUS_CS_EN		|
+			  IXP4XX_EXP_BUS_WR_EN		|
+			  IXP4XX_EXP_BUS_BYTE_EN;
+
+	/* max6369 on CS5 (512 bytes, 8bits, writable) */
+	vulcan_max6369_resource.start	= IXP4XX_EXP_BUS_BASE(5);
+	vulcan_max6369_resource.end	= IXP4XX_EXP_BUS_BASE(5);
+	*IXP4XX_EXP_CS5 = IXP4XX_EXP_BUS_CS_EN		|
+			  IXP4XX_EXP_BUS_WR_EN		|
+			  IXP4XX_EXP_BUS_BYTE_EN;
+
+	platform_add_devices(vulcan_devices, ARRAY_SIZE(vulcan_devices));
+}
+
+MACHINE_START(ARCOM_VULCAN, "Arcom/Eurotech Vulcan")
+	/* Maintainer: Marc Zyngier <maz@misterjones.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= vulcan_init,
+MACHINE_END