diff options
author | James Bottomley <James.Bottomley@suse.de> | 2011-04-24 14:30:14 -0500 |
---|---|---|
committer | Jeff Garzik <jgarzik@pobox.com> | 2011-05-14 14:59:15 -0400 |
commit | 9281b16caac1276817b77033c5b8a1f5ca30102c (patch) | |
tree | 73c554e4ab9e9dcfe1b610f2f65e0ae1713341b5 /drivers/ata/pata_cmd64x.c | |
parent | 5f6f12ccf3aa42cfc0c5bde9228df0c843dd63f7 (diff) | |
download | kernel_samsung_espresso10-9281b16caac1276817b77033c5b8a1f5ca30102c.zip kernel_samsung_espresso10-9281b16caac1276817b77033c5b8a1f5ca30102c.tar.gz kernel_samsung_espresso10-9281b16caac1276817b77033c5b8a1f5ca30102c.tar.bz2 |
pata_cm64x: fix boot crash on parisc
The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them. pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).
Fix this by porting the CNTRL register port detection logic from IDE
cmd64x. In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Diffstat (limited to 'drivers/ata/pata_cmd64x.c')
-rw-r--r-- | drivers/ata/pata_cmd64x.c | 42 |
1 files changed, 38 insertions, 4 deletions
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c index 905ff76..7bafc16 100644 --- a/drivers/ata/pata_cmd64x.c +++ b/drivers/ata/pata_cmd64x.c @@ -41,6 +41,9 @@ enum { CFR = 0x50, CFR_INTR_CH0 = 0x04, + CNTRL = 0x51, + CNTRL_CH0 = 0x04, + CNTRL_CH1 = 0x08, CMDTIM = 0x52, ARTTIM0 = 0x53, DRWTIM0 = 0x54, @@ -328,9 +331,19 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) .port_ops = &cmd648_port_ops } }; - const struct ata_port_info *ppi[] = { &cmd_info[id->driver_data], NULL }; - u8 mrdmode; + const struct ata_port_info *ppi[] = { + &cmd_info[id->driver_data], + &cmd_info[id->driver_data], + NULL + }; + u8 mrdmode, reg; int rc; + struct pci_dev *bridge = pdev->bus->self; + /* mobility split bridges don't report enabled ports correctly */ + int port_ok = !(bridge && bridge->vendor == + PCI_VENDOR_ID_MOBILITY_ELECTRONICS); + /* all (with exceptions below) apart from 643 have CNTRL_CH0 bit */ + int cntrl_ch0_ok = (id->driver_data != 0); rc = pcim_enable_device(pdev); if (rc) @@ -341,11 +354,18 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) if (pdev->device == PCI_DEVICE_ID_CMD_646) { /* Does UDMA work ? */ - if (pdev->revision > 4) + if (pdev->revision > 4) { ppi[0] = &cmd_info[2]; + ppi[1] = &cmd_info[2]; + } /* Early rev with other problems ? */ - else if (pdev->revision == 1) + else if (pdev->revision == 1) { ppi[0] = &cmd_info[3]; + ppi[1] = &cmd_info[3]; + } + /* revs 1,2 have no CNTRL_CH0 */ + if (pdev->revision < 3) + cntrl_ch0_ok = 0; } pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64); @@ -354,6 +374,20 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) mrdmode |= 0x02; /* Memory read line enable */ pci_write_config_byte(pdev, MRDMODE, mrdmode); + /* check for enabled ports */ + pci_read_config_byte(pdev, CNTRL, ®); + if (!port_ok) + dev_printk(KERN_NOTICE, &pdev->dev, "Mobility Bridge detected, ignoring CNTRL port enable/disable\n"); + if (port_ok && cntrl_ch0_ok && !(reg & CNTRL_CH0)) { + dev_printk(KERN_NOTICE, &pdev->dev, "Primary port is disabled\n"); + ppi[0] = &ata_dummy_port_info; + + } + if (port_ok && !(reg & CNTRL_CH1)) { + dev_printk(KERN_NOTICE, &pdev->dev, "Secondary port is disabled\n"); + ppi[1] = &ata_dummy_port_info; + } + /* Force PIO 0 here.. */ /* PPC specific fixup copied from old driver */ |