Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
  genetlink: fix netns vs. netlink table locking (2)
  3c59x: Get rid of "Trying to free already-free IRQ"
  tunnel: eliminate recursion field
  ems_pci: fix size of CAN controllers BAR mapping for CPC-PCI v2
  net: fix htmldocs sunrpc, clnt.c
  Phonet: error on broadcast sending (unimplemented)
  Phonet: fix race for port number in concurrent bind()
  pktgen: better scheduler friendliness
  pktgen: T_TERMINATE flag is unused
  ipv4: check optlen for IP_MULTICAST_IF option
  ath9k: Initialize txgain and rxgain for newer AR9287 chipsets.
  iwlagn: fix panic in iwl{5000,4965}_rx_reply_tx
  ath9k: Fix RFKILL bugs
  drivers/net/wireless: Use usb_endpoint_dir_out
  cfg80211: don't overwrite privacy setting
  wl12xx: fix kconfig/link errors
  rt2x00: fix the definition of rt2x00crypto_rx_insert_iv
  iwlwifi: reduce noise when skb allocation fails
  iwlwifi: do not send sync command while holding spinlock
  mac80211: fix DTIM setting
  ...

57 files changed, 2290 insertions, 456 deletions

diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
index 7adff4d..b9eeadf 100644
--- a/drivers/net/3c59x.c
+++ b/drivers/net/3c59x.c
@@ -813,10 +813,10 @@ static int vortex_suspend(struct pci_dev *pdev, pm_message_t state)
 		if (netif_running(dev)) {
 			netif_device_detach(dev);
 			vortex_down(dev, 1);
+			disable_irq(dev->irq);
 		}
 		pci_save_state(pdev);
 		pci_enable_wake(pdev, pci_choose_state(pdev, state), 0);
-		free_irq(dev->irq, dev);
 		pci_disable_device(pdev);
 		pci_set_power_state(pdev, pci_choose_state(pdev, state));
 	}
@@ -839,18 +839,12 @@ static int vortex_resume(struct pci_dev *pdev)
 			return err;
 		}
 		pci_set_master(pdev);
-		if (request_irq(dev->irq, vp->full_bus_master_rx ?
-				&boomerang_interrupt : &vortex_interrupt, IRQF_SHARED, dev->name, dev)) {
-			pr_warning("%s: Could not reserve IRQ %d\n", dev->name, dev->irq);
-			pci_disable_device(pdev);
-			return -EBUSY;
-		}
 		if (netif_running(dev)) {
 			err = vortex_up(dev);
 			if (err)
 				return err;
-			else
-				netif_device_attach(dev);
+			enable_irq(dev->irq);
+			netif_device_attach(dev);
 		}
 	}
 	return 0;
diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c
index 462d9f5..83a1922 100644
--- a/drivers/net/8139cp.c
+++ b/drivers/net/8139cp.c
@@ -87,7 +87,7 @@
 
 /* These identify the driver base version and may not be removed. */
 static char version[] =
-KERN_INFO DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE ")\n";
+DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE ")\n";
 
 MODULE_AUTHOR("Jeff Garzik <jgarzik@pobox.com>");
 MODULE_DESCRIPTION("RealTek RTL-8139C+ series 10/100 PCI Ethernet driver");
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ed5741b..2bea67c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1875,7 +1875,7 @@ config 68360_ENET
 
 config FEC
 	bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
-	depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35
+	depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
 	help
 	  Say Y here if you want to use the built-in 10/100 Fast ethernet
 	  controller on some Motorola ColdFire and Freescale i.MX processors.
diff --git a/drivers/net/atl1c/atl1c_main.c b/drivers/net/atl1c/atl1c_main.c
index be2c6cf..1372e9a 100644
--- a/drivers/net/atl1c/atl1c_main.c
+++ b/drivers/net/atl1c/atl1c_main.c
@@ -2296,7 +2296,7 @@ static int atl1c_suspend(struct pci_dev *pdev, pm_message_t state)
 	u32 ctrl;
 	u32 mac_ctrl_data;
 	u32 master_ctrl_data;
-	u32 wol_ctrl_data;
+	u32 wol_ctrl_data = 0;
 	u16 mii_bmsr_data;
 	u16 save_autoneg_advertised;
 	u16 mii_intr_status_data;
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index 0900743..df32c10 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -75,6 +75,13 @@ config CAN_EMS_PCI
 	  CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
 	  (http://www.ems-wuensche.de).
 
+config CAN_EMS_USB
+	tristate "EMS CPC-USB/ARM7 CAN/USB interface"
+	depends on USB && CAN_DEV
+	---help---
+	  This driver is for the one channel CPC-USB/ARM7 CAN/USB interface
+	  from from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+
 config CAN_KVASER_PCI
 	tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
 	depends on PCI && CAN_SJA1000
@@ -82,6 +89,12 @@ config CAN_KVASER_PCI
 	  This driver is for the the PCIcanx and PCIcan cards (1, 2 or
 	  4 channel) from Kvaser (http://www.kvaser.com).
 
+config CAN_AT91
+	tristate "Atmel AT91 onchip CAN controller"
+	depends on CAN && CAN_DEV && ARCH_AT91SAM9263
+	---help---
+	  This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
+
 config CAN_DEBUG_DEVICES
 	bool "CAN devices debugging messages"
 	depends on CAN
diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile
index 523a941..0dea627 100644
--- a/drivers/net/can/Makefile
+++ b/drivers/net/can/Makefile
@@ -7,6 +7,9 @@ obj-$(CONFIG_CAN_VCAN)		+= vcan.o
 obj-$(CONFIG_CAN_DEV)		+= can-dev.o
 can-dev-y			:= dev.o
 
+obj-y				+= usb/
+
 obj-$(CONFIG_CAN_SJA1000)	+= sja1000/
+obj-$(CONFIG_CAN_AT91)		+= at91_can.o
 
 ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG
diff --git a/drivers/net/can/sja1000/ems_pci.c b/drivers/net/can/sja1000/ems_pci.c
index 7d84b8a..fd04789 100644
--- a/drivers/net/can/sja1000/ems_pci.c
+++ b/drivers/net/can/sja1000/ems_pci.c
@@ -94,12 +94,14 @@ struct ems_pci_card {
 #define EMS_PCI_CDR             (CDR_CBP | CDR_CLKOUT_MASK)
 
 #define EMS_PCI_V1_BASE_BAR     1
-#define EMS_PCI_V1_MEM_SIZE     4096
+#define EMS_PCI_V1_CONF_SIZE    4096 /* size of PITA control area */
 #define EMS_PCI_V2_BASE_BAR     2
-#define EMS_PCI_V2_MEM_SIZE     128
+#define EMS_PCI_V2_CONF_SIZE    128 /* size of PLX control area */
 #define EMS_PCI_CAN_BASE_OFFSET 0x400 /* offset where the controllers starts */
 #define EMS_PCI_CAN_CTRL_SIZE   0x200 /* memory size for each controller */
 
+#define EMS_PCI_BASE_SIZE  4096 /* size of controller area */
+
 static struct pci_device_id ems_pci_tbl[] = {
 	/* CPC-PCI v1 */
 	{PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,},
@@ -224,7 +226,7 @@ static int __devinit ems_pci_add_card(struct pci_dev *pdev,
 	struct sja1000_priv *priv;
 	struct net_device *dev;
 	struct ems_pci_card *card;
-	int max_chan, mem_size, base_bar;
+	int max_chan, conf_size, base_bar;
 	int err, i;
 
 	/* Enabling PCI device */
@@ -251,22 +253,22 @@ static int __devinit ems_pci_add_card(struct pci_dev *pdev,
 		card->version = 2; /* CPC-PCI v2 */
 		max_chan = EMS_PCI_V2_MAX_CHAN;
 		base_bar = EMS_PCI_V2_BASE_BAR;
-		mem_size = EMS_PCI_V2_MEM_SIZE;
+		conf_size = EMS_PCI_V2_CONF_SIZE;
 	} else {
 		card->version = 1; /* CPC-PCI v1 */
 		max_chan = EMS_PCI_V1_MAX_CHAN;
 		base_bar = EMS_PCI_V1_BASE_BAR;
-		mem_size = EMS_PCI_V1_MEM_SIZE;
+		conf_size = EMS_PCI_V1_CONF_SIZE;
 	}
 
 	/* Remap configuration space and controller memory area */
-	card->conf_addr = pci_iomap(pdev, 0, mem_size);
+	card->conf_addr = pci_iomap(pdev, 0, conf_size);
 	if (card->conf_addr == NULL) {
 		err = -ENOMEM;
 		goto failure_cleanup;
 	}
 
-	card->base_addr = pci_iomap(pdev, base_bar, mem_size);
+	card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE);
 	if (card->base_addr == NULL) {
 		err = -ENOMEM;
 		goto failure_cleanup;
diff --git a/drivers/net/can/usb/Makefile b/drivers/net/can/usb/Makefile
new file mode 100644
index 0000000..c3f75ba
--- /dev/null
+++ b/drivers/net/can/usb/Makefile
@@ -0,0 +1,5 @@
+#
+#  Makefile for the Linux Controller Area Network USB drivers.
+#
+
+obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o
diff --git a/drivers/net/can/usb/ems_usb.c b/drivers/net/can/usb/ems_usb.c
new file mode 100644
index 0000000..9012e0a
--- /dev/null
+++ b/drivers/net/can/usb/ems_usb.c
@@ -0,0 +1,1155 @@
+/*
+ * CAN driver for EMS Dr. Thomas Wuensche CPC-USB/ARM7
+ *
+ * Copyright (C) 2004-2009 EMS Dr. Thomas Wuensche
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published
+ * by the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#include <linux/init.h>
+#include <linux/signal.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/usb.h>
+
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+
+MODULE_AUTHOR("Sebastian Haas <haas@ems-wuensche.com>");
+MODULE_DESCRIPTION("CAN driver for EMS Dr. Thomas Wuensche CAN/USB interfaces");
+MODULE_LICENSE("GPL v2");
+
+/* Control-Values for CPC_Control() Command Subject Selection */
+#define CONTR_CAN_MESSAGE 0x04
+#define CONTR_CAN_STATE   0x0C
+#define CONTR_BUS_ERROR   0x1C
+
+/* Control Command Actions */
+#define CONTR_CONT_OFF 0
+#define CONTR_CONT_ON  1
+#define CONTR_ONCE     2
+
+/* Messages from CPC to PC */
+#define CPC_MSG_TYPE_CAN_FRAME       1  /* CAN data frame */
+#define CPC_MSG_TYPE_RTR_FRAME       8  /* CAN remote frame */
+#define CPC_MSG_TYPE_CAN_PARAMS      12 /* Actual CAN parameters */
+#define CPC_MSG_TYPE_CAN_STATE       14 /* CAN state message */
+#define CPC_MSG_TYPE_EXT_CAN_FRAME   16 /* Extended CAN data frame */
+#define CPC_MSG_TYPE_EXT_RTR_FRAME   17 /* Extended remote frame */
+#define CPC_MSG_TYPE_CONTROL         19 /* change interface behavior */
+#define CPC_MSG_TYPE_CONFIRM         20 /* command processed confirmation */
+#define CPC_MSG_TYPE_OVERRUN         21 /* overrun events */
+#define CPC_MSG_TYPE_CAN_FRAME_ERROR 23 /* detected bus errors */
+#define CPC_MSG_TYPE_ERR_COUNTER     25 /* RX/TX error counter */
+
+/* Messages from the PC to the CPC interface  */
+#define CPC_CMD_TYPE_CAN_FRAME     1   /* CAN data frame */
+#define CPC_CMD_TYPE_CONTROL       3   /* control of interface behavior */
+#define CPC_CMD_TYPE_CAN_PARAMS    6   /* set CAN parameters */
+#define CPC_CMD_TYPE_RTR_FRAME     13  /* CAN remote frame */
+#define CPC_CMD_TYPE_CAN_STATE     14  /* CAN state message */
+#define CPC_CMD_TYPE_EXT_CAN_FRAME 15  /* Extended CAN data frame */
+#define CPC_CMD_TYPE_EXT_RTR_FRAME 16  /* Extended CAN remote frame */
+#define CPC_CMD_TYPE_CAN_EXIT      200 /* exit the CAN */
+
+#define CPC_CMD_TYPE_INQ_ERR_COUNTER 25 /* request the CAN error counters */
+#define CPC_CMD_TYPE_CLEAR_MSG_QUEUE 8  /* clear CPC_MSG queue */
+#define CPC_CMD_TYPE_CLEAR_CMD_QUEUE 28 /* clear CPC_CMD queue */
+
+#define CPC_CC_TYPE_SJA1000 2 /* Philips basic CAN controller */
+
+#define CPC_CAN_ECODE_ERRFRAME 0x01 /* Ecode type */
+
+/* Overrun types */
+#define CPC_OVR_EVENT_CAN       0x01
+#define CPC_OVR_EVENT_CANSTATE  0x02
+#define CPC_OVR_EVENT_BUSERROR  0x04
+
+/*
+ * If the CAN controller lost a message we indicate it with the highest bit
+ * set in the count field.
+ */
+#define CPC_OVR_HW 0x80
+
+/* Size of the "struct ems_cpc_msg" without the union */
+#define CPC_MSG_HEADER_LEN   11
+#define CPC_CAN_MSG_MIN_SIZE 5
+
+/* Define these values to match your devices */
+#define USB_CPCUSB_VENDOR_ID 0x12D6
+
+#define USB_CPCUSB_ARM7_PRODUCT_ID 0x0444
+
+/* Mode register NXP LPC2119/SJA1000 CAN Controller */
+#define SJA1000_MOD_NORMAL 0x00
+#define SJA1000_MOD_RM     0x01
+
+/* ECC register NXP LPC2119/SJA1000 CAN Controller */
+#define SJA1000_ECC_SEG   0x1F
+#define SJA1000_ECC_DIR   0x20
+#define SJA1000_ECC_ERR   0x06
+#define SJA1000_ECC_BIT   0x00
+#define SJA1000_ECC_FORM  0x40
+#define SJA1000_ECC_STUFF 0x80
+#define SJA1000_ECC_MASK  0xc0
+
+/* Status register content */
+#define SJA1000_SR_BS 0x80
+#define SJA1000_SR_ES 0x40
+
+#define SJA1000_DEFAULT_OUTPUT_CONTROL 0xDA
+
+/*
+ * The device actually uses a 16MHz clock to generate the CAN clock
+ * but it expects SJA1000 bit settings based on 8MHz (is internally
+ * converted).
+ */
+#define EMS_USB_ARM7_CLOCK 8000000
+
+/*
+ * CAN-Message representation in a CPC_MSG. Message object type is
+ * CPC_MSG_TYPE_CAN_FRAME or CPC_MSG_TYPE_RTR_FRAME or
+ * CPC_MSG_TYPE_EXT_CAN_FRAME or CPC_MSG_TYPE_EXT_RTR_FRAME.
+ */
+struct cpc_can_msg {
+	u32 id;
+	u8 length;
+	u8 msg[8];
+};
+
+/* Representation of the CAN parameters for the SJA1000 controller */
+struct cpc_sja1000_params {
+	u8 mode;
+	u8 acc_code0;
+	u8 acc_code1;
+	u8 acc_code2;
+	u8 acc_code3;
+	u8 acc_mask0;
+	u8 acc_mask1;
+	u8 acc_mask2;
+	u8 acc_mask3;
+	u8 btr0;
+	u8 btr1;
+	u8 outp_contr;
+};
+
+/* CAN params message representation */
+struct cpc_can_params {
+	u8 cc_type;
+
+	/* Will support M16C CAN controller in the future */
+	union {
+		struct cpc_sja1000_params sja1000;
+	} cc_params;
+};
+
+/* Structure for confirmed message handling */
+struct cpc_confirm {
+	u8 error; /* error code */
+};
+
+/* Structure for overrun conditions */
+struct cpc_overrun {
+	u8 event;
+	u8 count;
+};
+
+/* SJA1000 CAN errors (compatible to NXP LPC2119) */
+struct cpc_sja1000_can_error {
+	u8 ecc;
+	u8 rxerr;
+	u8 txerr;
+};
+
+/* structure for CAN error conditions */
+struct cpc_can_error {
+	u8 ecode;
+
+	struct {
+		u8 cc_type;
+
+		/* Other controllers may also provide error code capture regs */
+		union {
+			struct cpc_sja1000_can_error sja1000;
+		} regs;
+	} cc;
+};
+
+/*
+ * Structure containing RX/TX error counter. This structure is used to request
+ * the values of the CAN controllers TX and RX error counter.
+ */
+struct cpc_can_err_counter {
+	u8 rx;
+	u8 tx;
+};
+
+/* Main message type used between library and application */
+struct __attribute__ ((packed)) ems_cpc_msg {
+	u8 type;	/* type of message */
+	u8 length;	/* length of data within union 'msg' */
+	u8 msgid;	/* confirmation handle */
+	u32 ts_sec;	/* timestamp in seconds */
+	u32 ts_nsec;	/* timestamp in nano seconds */
+
+	union {
+		u8 generic[64];
+		struct cpc_can_msg can_msg;
+		struct cpc_can_params can_params;
+		struct cpc_confirm confirmation;
+		struct cpc_overrun overrun;
+		struct cpc_can_error error;
+		struct cpc_can_err_counter err_counter;
+		u8 can_state;
+	} msg;
+};
+
+/*
+ * Table of devices that work with this driver
+ * NOTE: This driver supports only CPC-USB/ARM7 (LPC2119) yet.
+ */
+static struct usb_device_id ems_usb_table[] = {
+	{USB_DEVICE(USB_CPCUSB_VENDOR_ID, USB_CPCUSB_ARM7_PRODUCT_ID)},
+	{} /* Terminating entry */
+};
+
+MODULE_DEVICE_TABLE(usb, ems_usb_table);
+
+#define RX_BUFFER_SIZE      64
+#define CPC_HEADER_SIZE     4
+#define INTR_IN_BUFFER_SIZE 4
+
+#define MAX_RX_URBS 10
+#define MAX_TX_URBS CAN_ECHO_SKB_MAX
+
+struct ems_usb;
+
+struct ems_tx_urb_context {
+	struct ems_usb *dev;
+
+	u32 echo_index;
+	u8 dlc;
+};
+
+struct ems_usb {
+	struct can_priv can; /* must be the first member */
+	int open_time;
+
+	struct sk_buff *echo_skb[MAX_TX_URBS];
+
+	struct usb_device *udev;
+	struct net_device *netdev;
+
+	atomic_t active_tx_urbs;
+	struct usb_anchor tx_submitted;
+	struct ems_tx_urb_context tx_contexts[MAX_TX_URBS];
+
+	struct usb_anchor rx_submitted;
+
+	struct urb *intr_urb;
+
+	u8 *tx_msg_buffer;
+
+	u8 *intr_in_buffer;
+	unsigned int free_slots; /* remember number of available slots */
+
+	struct ems_cpc_msg active_params; /* active controller parameters */
+};
+
+static void ems_usb_read_interrupt_callback(struct urb *urb)
+{
+	struct ems_usb *dev = urb->context;
+	struct net_device *netdev = dev->netdev;
+	int err;
+
+	if (!netif_device_present(netdev))
+		return;
+
+	switch (urb->status) {
+	case 0:
+		dev->free_slots = dev->intr_in_buffer[1];
+		break;
+
+	case -ECONNRESET: /* unlink */
+	case -ENOENT:
+	case -ESHUTDOWN:
+		return;
+
+	default:
+		dev_info(netdev->dev.parent, "Rx interrupt aborted %d\n",
+			 urb->status);
+		break;
+	}
+
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+
+	if (err == -ENODEV)
+		netif_device_detach(netdev);
+	else if (err)
+		dev_err(netdev->dev.parent,
+			"failed resubmitting intr urb: %d\n", err);
+
+	return;
+}
+
+static void ems_usb_rx_can_msg(struct ems_usb *dev, struct ems_cpc_msg *msg)
+{
+	struct can_frame *cf;
+	struct sk_buff *skb;
+	int i;
+	struct net_device_stats *stats = &dev->netdev->stats;
+
+	skb = netdev_alloc_skb(dev->netdev, sizeof(struct can_frame));
+	if (skb == NULL)
+		return;
+
+	skb->protocol = htons(ETH_P_CAN);
+
+	cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
+
+	cf->can_id = msg->msg.can_msg.id;
+	cf->can_dlc = min_t(u8, msg->msg.can_msg.length, 8);
+
+	if (msg->type == CPC_MSG_TYPE_EXT_CAN_FRAME
+	    || msg->type == CPC_MSG_TYPE_EXT_RTR_FRAME)
+		cf->can_id |= CAN_EFF_FLAG;
+
+	if (msg->type == CPC_MSG_TYPE_RTR_FRAME
+	    || msg->type == CPC_MSG_TYPE_EXT_RTR_FRAME) {
+		cf->can_id |= CAN_RTR_FLAG;
+	} else {
+		for (i = 0; i < cf->can_dlc; i++)
+			cf->data[i] = msg->msg.can_msg.msg[i];
+	}
+
+	netif_rx(skb);
+
+	stats->rx_packets++;
+	stats->rx_bytes += cf->can_dlc;
+}
+
+static void ems_usb_rx_err(struct ems_usb *dev, struct ems_cpc_msg *msg)
+{
+	struct can_frame *cf;
+	struct sk_buff *skb;
+	struct net_device_stats *stats = &dev->netdev->stats;
+
+	skb = netdev_alloc_skb(dev->netdev, sizeof(struct can_frame));
+	if (skb == NULL)
+		return;
+
+	skb->protocol = htons(ETH_P_CAN);
+
+	cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
+	memset(cf, 0, sizeof(struct can_frame));
+
+	cf->can_id = CAN_ERR_FLAG;
+	cf->can_dlc = CAN_ERR_DLC;
+
+	if (msg->type == CPC_MSG_TYPE_CAN_STATE) {
+		u8 state = msg->msg.can_state;
+
+		if (state & SJA1000_SR_BS) {
+			dev->can.state = CAN_STATE_BUS_OFF;
+			cf->can_id |= CAN_ERR_BUSOFF;
+
+			can_bus_off(dev->netdev);
+		} else if (state & SJA1000_SR_ES) {
+			dev->can.state = CAN_STATE_ERROR_WARNING;
+			dev->can.can_stats.error_warning++;
+		} else {
+			dev->can.state = CAN_STATE_ERROR_ACTIVE;
+			dev->can.can_stats.error_passive++;
+		}
+	} else if (msg->type == CPC_MSG_TYPE_CAN_FRAME_ERROR) {
+		u8 ecc = msg->msg.error.cc.regs.sja1000.ecc;
+		u8 txerr = msg->msg.error.cc.regs.sja1000.txerr;
+		u8 rxerr = msg->msg.error.cc.regs.sja1000.rxerr;
+
+		/* bus error interrupt */
+		dev->can.can_stats.bus_error++;
+		stats->rx_errors++;
+
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+
+		switch (ecc & SJA1000_ECC_MASK) {
+		case SJA1000_ECC_BIT:
+			cf->data[2] |= CAN_ERR_PROT_BIT;
+			break;
+		case SJA1000_ECC_FORM:
+			cf->data[2] |= CAN_ERR_PROT_FORM;
+			break;
+		case SJA1000_ECC_STUFF:
+			cf->data[2] |= CAN_ERR_PROT_STUFF;
+			break;
+		default:
+			cf->data[2] |= CAN_ERR_PROT_UNSPEC;
+			cf->data[3] = ecc & SJA1000_ECC_SEG;
+			break;
+		}
+
+		/* Error occured during transmission? */
+		if ((ecc & SJA1000_ECC_DIR) == 0)
+			cf->data[2] |= CAN_ERR_PROT_TX;
+
+		if (dev->can.state == CAN_STATE_ERROR_WARNING ||
+		    dev->can.state == CAN_STATE_ERROR_PASSIVE) {
+			cf->data[1] = (txerr > rxerr) ?
+			    CAN_ERR_CRTL_TX_PASSIVE : CAN_ERR_CRTL_RX_PASSIVE;
+		}
+	} else if (msg->type == CPC_MSG_TYPE_OVERRUN) {
+		cf->can_id |= CAN_ERR_CRTL;
+		cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+
+		stats->rx_over_errors++;
+		stats->rx_errors++;
+	}
+
+	netif_rx(skb);
+
+	stats->rx_packets++;
+	stats->rx_bytes += cf->can_dlc;
+}
+
+/*
+ * callback for bulk IN urb
+ */
+static void ems_usb_read_bulk_callback(struct urb *urb)
+{
+	struct ems_usb *dev = urb->context;
+	struct net_device *netdev;
+	int retval;
+
+	netdev = dev->netdev;
+
+	if (!netif_device_present(netdev))
+		return;
+
+	switch (urb->status) {
+	case 0: /* success */
+		break;
+
+	case -ENOENT:
+		return;
+
+	default:
+		dev_info(netdev->dev.parent, "Rx URB aborted (%d)\n",
+			 urb->status);
+		goto resubmit_urb;
+	}
+
+	if (urb->actual_length > CPC_HEADER_SIZE) {
+		struct ems_cpc_msg *msg;
+		u8 *ibuf = urb->transfer_buffer;
+		u8 msg_count, again, start;
+
+		msg_count = ibuf[0] & ~0x80;
+		again = ibuf[0] & 0x80;
+
+		start = CPC_HEADER_SIZE;
+
+		while (msg_count) {
+			msg = (struct ems_cpc_msg *)&ibuf[start];
+
+			switch (msg->type) {
+			case CPC_MSG_TYPE_CAN_STATE:
+				/* Process CAN state changes */
+				ems_usb_rx_err(dev, msg);
+				break;
+
+			case CPC_MSG_TYPE_CAN_FRAME:
+			case CPC_MSG_TYPE_EXT_CAN_FRAME:
+			case CPC_MSG_TYPE_RTR_FRAME:
+			case CPC_MSG_TYPE_EXT_RTR_FRAME:
+				ems_usb_rx_can_msg(dev, msg);
+				break;
+
+			case CPC_MSG_TYPE_CAN_FRAME_ERROR:
+				/* Process errorframe */
+				ems_usb_rx_err(dev, msg);
+				break;
+
+			case CPC_MSG_TYPE_OVERRUN:
+				/* Message lost while receiving */
+				ems_usb_rx_err(dev, msg);
+				break;
+			}
+
+			start += CPC_MSG_HEADER_LEN + msg->length;
+			msg_count--;
+
+			if (start > urb->transfer_buffer_length) {
+				dev_err(netdev->dev.parent, "format error\n");
+				break;
+			}
+		}
+	}
+
+resubmit_urb:
+	usb_fill_bulk_urb(urb, dev->udev, usb_rcvbulkpipe(dev->udev, 2),
+			  urb->transfer_buffer, RX_BUFFER_SIZE,
+			  ems_usb_read_bulk_callback, dev);
+
+	retval = usb_submit_urb(urb, GFP_ATOMIC);
+
+	if (retval == -ENODEV)
+		netif_device_detach(netdev);
+	else if (retval)
+		dev_err(netdev->dev.parent,
+			"failed resubmitting read bulk urb: %d\n", retval);
+
+	return;
+}
+
+/*
+ * callback for bulk IN urb
+ */
+static void ems_usb_write_bulk_callback(struct urb *urb)
+{
+	struct ems_tx_urb_context *context = urb->context;
+	struct ems_usb *dev;
+	struct net_device *netdev;
+
+	BUG_ON(!context);
+
+	dev = context->dev;
+	netdev = dev->netdev;
+
+	/* free up our allocated buffer */
+	usb_buffer_free(urb->dev, urb->transfer_buffer_length,
+			urb->transfer_buffer, urb->transfer_dma);
+
+	atomic_dec(&dev->active_tx_urbs);
+
+	if (!netif_device_present(netdev))
+		return;
+
+	if (urb->status)
+		dev_info(netdev->dev.parent, "Tx URB aborted (%d)\n",
+			 urb->status);
+
+	netdev->trans_start = jiffies;
+
+	/* transmission complete interrupt */
+	netdev->stats.tx_packets++;
+	netdev->stats.tx_bytes += context->dlc;
+
+	can_get_echo_skb(netdev, context->echo_index);
+
+	/* Release context */
+	context->echo_index = MAX_TX_URBS;
+
+	if (netif_queue_stopped(netdev))
+		netif_wake_queue(netdev);
+}
+
+/*
+ * Send the given CPC command synchronously
+ */
+static int ems_usb_command_msg(struct ems_usb *dev, struct ems_cpc_msg *msg)
+{
+	int actual_length;
+
+	/* Copy payload */
+	memcpy(&dev->tx_msg_buffer[CPC_HEADER_SIZE], msg,
+	       msg->length + CPC_MSG_HEADER_LEN);
+
+	/* Clear header */
+	memset(&dev->tx_msg_buffer[0], 0, CPC_HEADER_SIZE);
+
+	return usb_bulk_msg(dev->udev, usb_sndbulkpipe(dev->udev, 2),
+			    &dev->tx_msg_buffer[0],
+			    msg->length + CPC_MSG_HEADER_LEN + CPC_HEADER_SIZE,
+			    &actual_length, 1000);
+}
+
+/*
+ * Change CAN controllers' mode register
+ */
+static int ems_usb_write_mode(struct ems_usb *dev, u8 mode)
+{
+	dev->active_params.msg.can_params.cc_params.sja1000.mode = mode;
+
+	return ems_usb_command_msg(dev, &dev->active_params);
+}
+
+/*
+ * Send a CPC_Control command to change behaviour when interface receives a CAN
+ * message, bus error or CAN state changed notifications.
+ */
+static int ems_usb_control_cmd(struct ems_usb *dev, u8 val)
+{
+	struct ems_cpc_msg cmd;
+
+	cmd.type = CPC_CMD_TYPE_CONTROL;
+	cmd.length = CPC_MSG_HEADER_LEN + 1;
+
+	cmd.msgid = 0;
+
+	cmd.msg.generic[0] = val;
+
+	return ems_usb_command_msg(dev, &cmd);
+}
+
+/*
+ * Start interface
+ */
+static int ems_usb_start(struct ems_usb *dev)
+{
+	struct net_device *netdev = dev->netdev;
+	int err, i;
+
+	dev->intr_in_buffer[0] = 0;
+	dev->free_slots = 15; /* initial size */
+
+	for (i = 0; i < MAX_RX_URBS; i++) {
+		struct urb *urb = NULL;
+		u8 *buf = NULL;
+
+		/* create a URB, and a buffer for it */
+		urb = usb_alloc_urb(0, GFP_KERNEL);
+		if (!urb) {
+			dev_err(netdev->dev.parent,
+				"No memory left for URBs\n");
+			return -ENOMEM;
+		}
+
+		buf = usb_buffer_alloc(dev->udev, RX_BUFFER_SIZE, GFP_KERNEL,
+				       &urb->transfer_dma);
+		if (!buf) {
+			dev_err(netdev->dev.parent,
+				"No memory left for USB buffer\n");
+			usb_free_urb(urb);
+			return -ENOMEM;
+		}
+
+		usb_fill_bulk_urb(urb, dev->udev, usb_rcvbulkpipe(dev->udev, 2),
+				  buf, RX_BUFFER_SIZE,
+				  ems_usb_read_bulk_callback, dev);
+		urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+		usb_anchor_urb(urb, &dev->rx_submitted);
+
+		err = usb_submit_urb(urb, GFP_KERNEL);
+		if (err) {
+			if (err == -ENODEV)
+				netif_device_detach(dev->netdev);
+
+			usb_unanchor_urb(urb);
+			usb_buffer_free(dev->udev, RX_BUFFER_SIZE, buf,
+					urb->transfer_dma);
+			break;
+		}
+
+		/* Drop reference, USB core will take care of freeing it */
+		usb_free_urb(urb);
+	}
+
+	/* Did we submit any URBs */
+	if (i == 0) {
+		dev_warn(netdev->dev.parent, "couldn't setup read URBs\n");
+		return err;
+	}
+
+	/* Warn if we've couldn't transmit all the URBs */
+	if (i < MAX_RX_URBS)
+		dev_warn(netdev->dev.parent, "rx performance may be slow\n");
+
+	/* Setup and start interrupt URB */
+	usb_fill_int_urb(dev->intr_urb, dev->udev,
+			 usb_rcvintpipe(dev->udev, 1),
+			 dev->intr_in_buffer,
+			 INTR_IN_BUFFER_SIZE,
+			 ems_usb_read_interrupt_callback, dev, 1);
+
+	err = usb_submit_urb(dev->intr_urb, GFP_KERNEL);
+	if (err) {
+		if (err == -ENODEV)
+			netif_device_detach(dev->netdev);
+
+		dev_warn(netdev->dev.parent, "intr URB submit failed: %d\n",
+			 err);
+
+		return err;
+	}
+
+	/* CPC-USB will transfer received message to host */
+	err = ems_usb_control_cmd(dev, CONTR_CAN_MESSAGE | CONTR_CONT_ON);
+	if (err)
+		goto failed;
+
+	/* CPC-USB will transfer CAN state changes to host */
+	err = ems_usb_control_cmd(dev, CONTR_CAN_STATE | CONTR_CONT_ON);
+	if (err)
+		goto failed;
+
+	/* CPC-USB will transfer bus errors to host */
+	err = ems_usb_control_cmd(dev, CONTR_BUS_ERROR | CONTR_CONT_ON);
+	if (err)
+		goto failed;
+
+	err = ems_usb_write_mode(dev, SJA1000_MOD_NORMAL);
+	if (err)
+		goto failed;
+
+	dev->can.state = CAN_STATE_ERROR_ACTIVE;
+
+	return 0;
+
+failed:
+	if (err == -ENODEV)
+		netif_device_detach(dev->netdev);
+
+	dev_warn(netdev->dev.parent, "couldn't submit control: %d\n", err);
+
+	return err;
+}
+
+static void unlink_all_urbs(struct ems_usb *dev)
+{
+	int i;
+
+	usb_unlink_urb(dev->intr_urb);
+
+	usb_kill_anchored_urbs(&dev->rx_submitted);
+
+	usb_kill_anchored_urbs(&dev->tx_submitted);
+	atomic_set(&dev->active_tx_urbs, 0);
+
+	for (i = 0; i < MAX_TX_URBS; i++)
+		dev->tx_contexts[i].echo_index = MAX_TX_URBS;
+}
+
+static int ems_usb_open(struct net_device *netdev)
+{
+	struct ems_usb *dev = netdev_priv(netdev);
+	int err;
+
+	err = ems_usb_write_mode(dev, SJA1000_MOD_RM);
+	if (err)
+		return err;
+
+	/* common open */
+	err = open_candev(netdev);
+	if (err)
+		return err;
+
+	/* finally start device */
+	err = ems_usb_start(dev);
+	if (err) {
+		if (err == -ENODEV)
+			netif_device_detach(dev->netdev);
+
+		dev_warn(netdev->dev.parent, "couldn't start device: %d\n",
+			 err);
+
+		close_candev(netdev);
+
+		return err;
+	}
+
+	dev->open_time = jiffies;
+
+	netif_start_queue(netdev);
+
+	return 0;
+}
+
+static netdev_tx_t ems_usb_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+	struct ems_usb *dev = netdev_priv(netdev);
+	struct ems_tx_urb_context *context = NULL;
+	struct net_device_stats *stats = &netdev->stats;
+	struct can_frame *cf = (struct can_frame *)skb->data;
+	struct ems_cpc_msg *msg;
+	struct urb *urb;
+	u8 *buf;
+	int i, err;
+	size_t size = CPC_HEADER_SIZE + CPC_MSG_HEADER_LEN
+			+ sizeof(struct cpc_can_msg);
+
+	/* create a URB, and a buffer for it, and copy the data to the URB */
+	urb = usb_alloc_urb(0, GFP_ATOMIC);
+	if (!urb) {
+		dev_err(netdev->dev.parent, "No memory left for URBs\n");
+		goto nomem;
+	}
+
+	buf = usb_buffer_alloc(dev->udev, size, GFP_ATOMIC, &urb->transfer_dma);
+	if (!buf) {
+		dev_err(netdev->dev.parent, "No memory left for USB buffer\n");
+		usb_free_urb(urb);
+		goto nomem;
+	}
+
+	msg = (struct ems_cpc_msg *)&buf[CPC_HEADER_SIZE];
+
+	msg->msg.can_msg.id = cf->can_id & CAN_ERR_MASK;
+	msg->msg.can_msg.length = cf->can_dlc;
+
+	if (cf->can_id & CAN_RTR_FLAG) {
+		msg->type = cf->can_id & CAN_EFF_FLAG ?
+			CPC_CMD_TYPE_EXT_RTR_FRAME : CPC_CMD_TYPE_RTR_FRAME;
+
+		msg->length = CPC_CAN_MSG_MIN_SIZE;
+	} else {
+		msg->type = cf->can_id & CAN_EFF_FLAG ?
+			CPC_CMD_TYPE_EXT_CAN_FRAME : CPC_CMD_TYPE_CAN_FRAME;
+
+		for (i = 0; i < cf->can_dlc; i++)
+			msg->msg.can_msg.msg[i] = cf->data[i];
+
+		msg->length = CPC_CAN_MSG_MIN_SIZE + cf->can_dlc;
+	}
+
+	for (i = 0; i < MAX_TX_URBS; i++) {
+		if (dev->tx_contexts[i].echo_index == MAX_TX_URBS) {
+			context = &dev->tx_contexts[i];
+			break;
+		}
+	}
+
+	/*
+	 * May never happen! When this happens we'd more URBs in flight as
+	 * allowed (MAX_TX_URBS).
+	 */
+	if (!context) {
+		usb_unanchor_urb(urb);
+		usb_buffer_free(dev->udev, size, buf, urb->transfer_dma);
+
+		dev_warn(netdev->dev.parent, "couldn't find free context\n");
+
+		return NETDEV_TX_BUSY;
+	}
+
+	context->dev = dev;
+	context->echo_index = i;
+	context->dlc = cf->can_dlc;
+
+	usb_fill_bulk_urb(urb, dev->udev, usb_sndbulkpipe(dev->udev, 2), buf,
+			  size, ems_usb_write_bulk_callback, context);
+	urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+	usb_anchor_urb(urb, &dev->tx_submitted);
+
+	can_put_echo_skb(skb, netdev, context->echo_index);
+
+	atomic_inc(&dev->active_tx_urbs);
+
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+	if (unlikely(err)) {
+		can_free_echo_skb(netdev, context->echo_index);
+
+		usb_unanchor_urb(urb);
+		usb_buffer_free(dev->udev, size, buf, urb->transfer_dma);
+		dev_kfree_skb(skb);
+
+		atomic_dec(&dev->active_tx_urbs);
+
+		if (err == -ENODEV) {
+			netif_device_detach(netdev);
+		} else {
+			dev_warn(netdev->dev.parent, "failed tx_urb %d\n", err);
+
+			stats->tx_dropped++;
+		}
+	} else {
+		netdev->trans_start = jiffies;
+
+		/* Slow down tx path */
+		if (atomic_read(&dev->active_tx_urbs) >= MAX_TX_URBS ||
+		    dev->free_slots < 5) {
+			netif_stop_queue(netdev);
+		}
+	}
+
+	/*
+	 * Release our reference to this URB, the USB core will eventually free
+	 * it entirely.
+	 */
+	usb_free_urb(urb);
+
+	return NETDEV_TX_OK;
+
+nomem:
+	if (skb)
+		dev_kfree_skb(skb);
+
+	stats->tx_dropped++;
+
+	return NETDEV_TX_OK;
+}
+
+static int ems_usb_close(struct net_device *netdev)
+{
+	struct ems_usb *dev = netdev_priv(netdev);
+
+	/* Stop polling */
+	unlink_all_urbs(dev);
+
+	netif_stop_queue(netdev);
+
+	/* Set CAN controller to reset mode */
+	if (ems_usb_write_mode(dev, SJA1000_MOD_RM))
+		dev_warn(netdev->dev.parent, "couldn't stop device");
+
+	close_candev(netdev);
+
+	dev->open_time = 0;
+
+	return 0;
+}
+
+static const struct net_device_ops ems_usb_netdev_ops = {
+	.ndo_open = ems_usb_open,
+	.ndo_stop = ems_usb_close,
+	.ndo_start_xmit = ems_usb_start_xmit,
+};
+
+static struct can_bittiming_const ems_usb_bittiming_const = {
+	.name = "ems_usb",
+	.tseg1_min = 1,
+	.tseg1_max = 16,
+	.tseg2_min = 1,
+	.tseg2_max = 8,
+	.sjw_max = 4,
+	.brp_min = 1,
+	.brp_max = 64,
+	.brp_inc = 1,
+};
+
+static int ems_usb_set_mode(struct net_device *netdev, enum can_mode mode)
+{
+	struct ems_usb *dev = netdev_priv(netdev);
+
+	if (!dev->open_time)
+		return -EINVAL;
+
+	switch (mode) {
+	case CAN_MODE_START:
+		if (ems_usb_write_mode(dev, SJA1000_MOD_NORMAL))
+			dev_warn(netdev->dev.parent, "couldn't start device");
+
+		if (netif_queue_stopped(netdev))
+			netif_wake_queue(netdev);
+		break;
+
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
+static int ems_usb_set_bittiming(struct net_device *netdev)
+{
+	struct ems_usb *dev = netdev_priv(netdev);
+	struct can_bittiming *bt = &dev->can.bittiming;
+	u8 btr0, btr1;
+
+	btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6);
+	btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) |
+		(((bt->phase_seg2 - 1) & 0x7) << 4);
+	if (dev->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
+		btr1 |= 0x80;
+
+	dev_info(netdev->dev.parent, "setting BTR0=0x%02x BTR1=0x%02x\n",
+		 btr0, btr1);
+
+	dev->active_params.msg.can_params.cc_params.sja1000.btr0 = btr0;
+	dev->active_params.msg.can_params.cc_params.sja1000.btr1 = btr1;
+
+	return ems_usb_command_msg(dev, &dev->active_params);
+}
+
+static void init_params_sja1000(struct ems_cpc_msg *msg)
+{
+	struct cpc_sja1000_params *sja1000 =
+		&msg->msg.can_params.cc_params.sja1000;
+
+	msg->type = CPC_CMD_TYPE_CAN_PARAMS;
+	msg->length = sizeof(struct cpc_can_params);
+	msg->msgid = 0;
+
+	msg->msg.can_params.cc_type = CPC_CC_TYPE_SJA1000;
+
+	/* Acceptance filter open */
+	sja1000->acc_code0 = 0x00;
+	sja1000->acc_code1 = 0x00;
+	sja1000->acc_code2 = 0x00;
+	sja1000->acc_code3 = 0x00;
+
+	/* Acceptance filter open */
+	sja1000->acc_mask0 = 0xFF;
+	sja1000->acc_mask1 = 0xFF;
+	sja1000->acc_mask2 = 0xFF;
+	sja1000->acc_mask3 = 0xFF;
+
+	sja1000->btr0 = 0;
+	sja1000->btr1 = 0;
+
+	sja1000->outp_contr = SJA1000_DEFAULT_OUTPUT_CONTROL;
+	sja1000->mode = SJA1000_MOD_RM;
+}
+
+/*
+ * probe function for new CPC-USB devices
+ */
+static int ems_usb_probe(struct usb_interface *intf,
+			 const struct usb_device_id *id)
+{
+	struct net_device *netdev;
+	struct ems_usb *dev;
+	int i, err = -ENOMEM;
+
+	netdev = alloc_candev(sizeof(struct ems_usb));
+	if (!netdev) {
+		dev_err(netdev->dev.parent, "Couldn't alloc candev\n");
+		return -ENOMEM;
+	}
+
+	dev = netdev_priv(netdev);
+
+	dev->udev = interface_to_usbdev(intf);
+	dev->netdev = netdev;
+
+	dev->can.state = CAN_STATE_STOPPED;
+	dev->can.clock.freq = EMS_USB_ARM7_CLOCK;
+	dev->can.bittiming_const = &ems_usb_bittiming_const;
+	dev->can.do_set_bittiming = ems_usb_set_bittiming;
+	dev->can.do_set_mode = ems_usb_set_mode;
+
+	netdev->flags |= IFF_ECHO; /* we support local echo */
+
+	netdev->netdev_ops = &ems_usb_netdev_ops;
+
+	netdev->flags |= IFF_ECHO; /* we support local echo */
+
+	init_usb_anchor(&dev->rx_submitted);
+
+	init_usb_anchor(&dev->tx_submitted);
+	atomic_set(&dev->active_tx_urbs, 0);
+
+	for (i = 0; i < MAX_TX_URBS; i++)
+		dev->tx_contexts[i].echo_index = MAX_TX_URBS;
+
+	dev->intr_urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!dev->intr_urb) {
+		dev_err(netdev->dev.parent, "Couldn't alloc intr URB\n");
+		goto cleanup_candev;
+	}
+
+	dev->intr_in_buffer = kzalloc(INTR_IN_BUFFER_SIZE, GFP_KERNEL);
+	if (!dev->intr_in_buffer) {
+		dev_err(netdev->dev.parent, "Couldn't alloc Intr buffer\n");
+		goto cleanup_intr_urb;
+	}
+
+	dev->tx_msg_buffer = kzalloc(CPC_HEADER_SIZE +
+				     sizeof(struct ems_cpc_msg), GFP_KERNEL);
+	if (!dev->tx_msg_buffer) {
+		dev_err(netdev->dev.parent, "Couldn't alloc Tx buffer\n");
+		goto cleanup_intr_in_buffer;
+	}
+
+	usb_set_intfdata(intf, dev);
+
+	SET_NETDEV_DEV(netdev, &intf->dev);
+
+	init_params_sja1000(&dev->active_params);
+
+	err = ems_usb_command_msg(dev, &dev->active_params);
+	if (err) {
+		dev_err(netdev->dev.parent,
+			"couldn't initialize controller: %d\n", err);
+		goto cleanup_tx_msg_buffer;
+	}
+
+	err = register_candev(netdev);
+	if (err) {
+		dev_err(netdev->dev.parent,
+			"couldn't register CAN device: %d\n", err);
+		goto cleanup_tx_msg_buffer;
+	}
+
+	return 0;
+
+cleanup_tx_msg_buffer:
+	kfree(dev->tx_msg_buffer);
+
+cleanup_intr_in_buffer:
+	kfree(dev->intr_in_buffer);
+
+cleanup_intr_urb:
+	usb_free_urb(dev->intr_urb);
+
+cleanup_candev:
+	free_candev(netdev);
+
+	return err;
+}
+
+/*
+ * called by the usb core when the device is removed from the system
+ */
+static void ems_usb_disconnect(struct usb_interface *intf)
+{
+	struct ems_usb *dev = usb_get_intfdata(intf);
+
+	usb_set_intfdata(intf, NULL);
+
+	if (dev) {
+		unregister_netdev(dev->netdev);
+		free_candev(dev->netdev);
+
+		unlink_all_urbs(dev);
+
+		usb_free_urb(dev->intr_urb);
+
+		kfree(dev->intr_in_buffer);
+	}
+}
+
+/* usb specific object needed to register this driver with the usb subsystem */
+static struct usb_driver ems_usb_driver = {
+	.name = "ems_usb",
+	.probe = ems_usb_probe,
+	.disconnect = ems_usb_disconnect,
+	.id_table = ems_usb_table,
+};
+
+static int __init ems_usb_init(void)
+{
+	int err;
+
+	printk(KERN_INFO "CPC-USB kernel driver loaded\n");
+
+	/* register this driver with the USB subsystem */
+	err = usb_register(&ems_usb_driver);
+
+	if (err) {
+		err("usb_register failed. Error number %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static void __exit ems_usb_exit(void)
+{
+	/* deregister this driver with the USB subsystem */
+	usb_deregister(&ems_usb_driver);
+}
+
+module_init(ems_usb_init);
+module_exit(ems_usb_exit);
diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c
index d45eacb..211c8e9 100644
--- a/drivers/net/cnic.c
+++ b/drivers/net/cnic.c
@@ -85,8 +85,6 @@ static int cnic_uio_open(struct uio_info *uinfo, struct inode *inode)
 
 	cp->uio_dev = iminor(inode);
 
-	cnic_shutdown_bnx2_rx_ring(dev);
-
 	cnic_init_bnx2_tx_ring(dev);
 	cnic_init_bnx2_rx_ring(dev);
 
@@ -98,6 +96,8 @@ static int cnic_uio_close(struct uio_info *uinfo, struct inode *inode)
 	struct cnic_dev *dev = uinfo->priv;
 	struct cnic_local *cp = dev->cnic_priv;
 
+	cnic_shutdown_bnx2_rx_ring(dev);
+
 	cp->uio_dev = -1;
 	return 0;
 }
diff --git a/drivers/net/cpmac.c b/drivers/net/cpmac.c
index 3e3fab8..61f9da2 100644
--- a/drivers/net/cpmac.c
+++ b/drivers/net/cpmac.c
@@ -1109,7 +1109,7 @@ static int external_switch;
 static int __devinit cpmac_probe(struct platform_device *pdev)
 {
 	int rc, phy_id;
-	char mdio_bus_id[BUS_ID_SIZE];
+	char mdio_bus_id[MII_BUS_ID_SIZE];
 	struct resource *mem;
 	struct cpmac_priv *priv;
 	struct net_device *dev;
@@ -1118,7 +1118,7 @@ static int __devinit cpmac_probe(struct platform_device *pdev)
 	pdata = pdev->dev.platform_data;
 
 	if (external_switch || dumb_switch) {
-		strncpy(mdio_bus_id, "0", BUS_ID_SIZE); /* fixed phys bus */
+		strncpy(mdio_bus_id, "0", MII_BUS_ID_SIZE); /* fixed phys bus */
 		phy_id = pdev->id;
 	} else {
 		for (phy_id = 0; phy_id < PHY_MAX_ADDR; phy_id++) {
@@ -1126,7 +1126,7 @@ static int __devinit cpmac_probe(struct platform_device *pdev)
 				continue;
 			if (!cpmac_mii->phy_map[phy_id])
 				continue;
-			strncpy(mdio_bus_id, cpmac_mii->id, BUS_ID_SIZE);
+			strncpy(mdio_bus_id, cpmac_mii->id, MII_BUS_ID_SIZE);
 			break;
 		}
 	}
@@ -1167,7 +1167,7 @@ static int __devinit cpmac_probe(struct platform_device *pdev)
 	priv->msg_enable = netif_msg_init(debug_level, 0xff);
 	memcpy(dev->dev_addr, pdata->dev_addr, sizeof(dev->dev_addr));
 
-	snprintf(priv->phy_name, BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
+	snprintf(priv->phy_name, MII_BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
 
 	priv->phy = phy_connect(dev, priv->phy_name, &cpmac_adjust_link, 0,
 						PHY_INTERFACE_MODE_MII);
diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c
index 977c3d3..41bd7ae 100644
--- a/drivers/net/ehea/ehea_main.c
+++ b/drivers/net/ehea/ehea_main.c
@@ -3083,7 +3083,6 @@ static const struct net_device_ops ehea_netdev_ops = {
 	.ndo_poll_controller	= ehea_netpoll,
 #endif
 	.ndo_get_stats		= ehea_get_stats,
-	.ndo_change_mtu		= eth_change_mtu,
 	.ndo_set_mac_address	= ehea_set_mac_addr,
 	.ndo_validate_addr	= eth_validate_addr,
 	.ndo_set_multicast_list	= ehea_set_multicast_list,
diff --git a/drivers/net/igb/e1000_mac.c b/drivers/net/igb/e1000_mac.c
index a0231cd..7d76bb0 100644
--- a/drivers/net/igb/e1000_mac.c
+++ b/drivers/net/igb/e1000_mac.c
@@ -286,41 +286,6 @@ void igb_mta_set(struct e1000_hw *hw, u32 hash_value)
 }
 
 /**
- *  igb_update_mc_addr_list - Update Multicast addresses
- *  @hw: pointer to the HW structure
- *  @mc_addr_list: array of multicast addresses to program
- *  @mc_addr_count: number of multicast addresses to program
- *
- *  Updates entire Multicast Table Array.
- *  The caller must have a packed mc_addr_list of multicast addresses.
- **/
-void igb_update_mc_addr_list(struct e1000_hw *hw,
-                             u8 *mc_addr_list, u32 mc_addr_count)
-{
-	u32 hash_value, hash_bit, hash_reg;
-	int i;
-
-	/* clear mta_shadow */
-	memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
-
-	/* update mta_shadow from mc_addr_list */
-	for (i = 0; (u32) i < mc_addr_count; i++) {
-		hash_value = igb_hash_mc_addr(hw, mc_addr_list);
-
-		hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
-		hash_bit = hash_value & 0x1F;
-
-		hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
-		mc_addr_list += (ETH_ALEN);
-	}
-
-	/* replace the entire MTA table */
-	for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
-		array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
-	wrfl();
-}
-
-/**
  *  igb_hash_mc_addr - Generate a multicast hash value
  *  @hw: pointer to the HW structure
  *  @mc_addr: pointer to a multicast address
@@ -329,7 +294,7 @@ void igb_update_mc_addr_list(struct e1000_hw *hw,
  *  the multicast filter table array address and new table value.  See
  *  igb_mta_set()
  **/
-u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
 {
 	u32 hash_value, hash_mask;
 	u8 bit_shift = 0;
@@ -392,6 +357,41 @@ u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
 }
 
 /**
+ *  igb_update_mc_addr_list - Update Multicast addresses
+ *  @hw: pointer to the HW structure
+ *  @mc_addr_list: array of multicast addresses to program
+ *  @mc_addr_count: number of multicast addresses to program
+ *
+ *  Updates entire Multicast Table Array.
+ *  The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+void igb_update_mc_addr_list(struct e1000_hw *hw,
+                             u8 *mc_addr_list, u32 mc_addr_count)
+{
+	u32 hash_value, hash_bit, hash_reg;
+	int i;
+
+	/* clear mta_shadow */
+	memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
+
+	/* update mta_shadow from mc_addr_list */
+	for (i = 0; (u32) i < mc_addr_count; i++) {
+		hash_value = igb_hash_mc_addr(hw, mc_addr_list);
+
+		hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+		hash_bit = hash_value & 0x1F;
+
+		hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
+		mc_addr_list += (ETH_ALEN);
+	}
+
+	/* replace the entire MTA table */
+	for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
+		array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
+	wrfl();
+}
+
+/**
  *  igb_clear_hw_cntrs_base - Clear base hardware counters
  *  @hw: pointer to the HW structure
  *
diff --git a/drivers/net/igb/e1000_mac.h b/drivers/net/igb/e1000_mac.h
index 7518af8..bca17d8 100644
--- a/drivers/net/igb/e1000_mac.h
+++ b/drivers/net/igb/e1000_mac.h
@@ -88,6 +88,5 @@ enum e1000_mng_mode {
 #define E1000_MNG_DHCP_COOKIE_STATUS_VLAN    0x2
 
 extern void e1000_init_function_pointers_82575(struct e1000_hw *hw);
-extern u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr);
 
 #endif
diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h
index dd688d4..385be60 100644
--- a/drivers/net/ixgbe/ixgbe.h
+++ b/drivers/net/ixgbe/ixgbe.h
@@ -267,7 +267,8 @@ struct ixgbe_adapter {
 	enum ixgbe_fc_mode last_lfc_mode;
 
 	/* Interrupt Throttle Rate */
-	u32 itr_setting;
+	u32 rx_itr_setting;
+	u32 tx_itr_setting;
 	u16 eitr_low;
 	u16 eitr_high;
 
@@ -351,7 +352,8 @@ struct ixgbe_adapter {
 	struct ixgbe_hw_stats stats;
 
 	/* Interrupt Throttle Rate */
-	u32 eitr_param;
+	u32 rx_eitr_param;
+	u32 tx_eitr_param;
 
 	unsigned long state;
 	u64 tx_busy;
diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c
index 026e94a..53b0a66 100644
--- a/drivers/net/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ixgbe/ixgbe_ethtool.c
@@ -1929,7 +1929,7 @@ static int ixgbe_get_coalesce(struct net_device *netdev,
 	ec->tx_max_coalesced_frames_irq = adapter->tx_ring[0].work_limit;
 
 	/* only valid if in constant ITR mode */
-	switch (adapter->itr_setting) {
+	switch (adapter->rx_itr_setting) {
 	case 0:
 		/* throttling disabled */
 		ec->rx_coalesce_usecs = 0;
@@ -1940,9 +1940,25 @@ static int ixgbe_get_coalesce(struct net_device *netdev,
 		break;
 	default:
 		/* fixed interrupt rate mode */
-		ec->rx_coalesce_usecs = 1000000/adapter->eitr_param;
+		ec->rx_coalesce_usecs = 1000000/adapter->rx_eitr_param;
 		break;
 	}
+
+	/* only valid if in constant ITR mode */
+	switch (adapter->tx_itr_setting) {
+	case 0:
+		/* throttling disabled */
+		ec->tx_coalesce_usecs = 0;
+		break;
+	case 1:
+		/* dynamic ITR mode */
+		ec->tx_coalesce_usecs = 1;
+		break;
+	default:
+		ec->tx_coalesce_usecs = 1000000/adapter->tx_eitr_param;
+		break;
+	}
+
 	return 0;
 }
 
@@ -1953,6 +1969,14 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 	struct ixgbe_q_vector *q_vector;
 	int i;
 
+	/*
+	 * don't accept tx specific changes if we've got mixed RxTx vectors
+	 * test and jump out here if needed before changing the rx numbers
+	 */
+	if ((1000000/ec->tx_coalesce_usecs) != adapter->tx_eitr_param &&
+	    adapter->q_vector[0]->txr_count && adapter->q_vector[0]->rxr_count)
+		return -EINVAL;
+
 	if (ec->tx_max_coalesced_frames_irq)
 		adapter->tx_ring[0].work_limit = ec->tx_max_coalesced_frames_irq;
 
@@ -1963,26 +1987,49 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 			return -EINVAL;
 
 		/* store the value in ints/second */
-		adapter->eitr_param = 1000000/ec->rx_coalesce_usecs;
+		adapter->rx_eitr_param = 1000000/ec->rx_coalesce_usecs;
 
 		/* static value of interrupt rate */
-		adapter->itr_setting = adapter->eitr_param;
+		adapter->rx_itr_setting = adapter->rx_eitr_param;
 		/* clear the lower bit as its used for dynamic state */
-		adapter->itr_setting &= ~1;
+		adapter->rx_itr_setting &= ~1;
 	} else if (ec->rx_coalesce_usecs == 1) {
 		/* 1 means dynamic mode */
-		adapter->eitr_param = 20000;
-		adapter->itr_setting = 1;
+		adapter->rx_eitr_param = 20000;
+		adapter->rx_itr_setting = 1;
 	} else {
 		/*
 		 * any other value means disable eitr, which is best
 		 * served by setting the interrupt rate very high
 		 */
 		if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED)
-			adapter->eitr_param = IXGBE_MAX_RSC_INT_RATE;
+			adapter->rx_eitr_param = IXGBE_MAX_RSC_INT_RATE;
 		else
-			adapter->eitr_param = IXGBE_MAX_INT_RATE;
-		adapter->itr_setting = 0;
+			adapter->rx_eitr_param = IXGBE_MAX_INT_RATE;
+		adapter->rx_itr_setting = 0;
+	}
+
+	if (ec->tx_coalesce_usecs > 1) {
+		/* check the limits */
+		if ((1000000/ec->tx_coalesce_usecs > IXGBE_MAX_INT_RATE) ||
+		    (1000000/ec->tx_coalesce_usecs < IXGBE_MIN_INT_RATE))
+			return -EINVAL;
+
+		/* store the value in ints/second */
+		adapter->tx_eitr_param = 1000000/ec->tx_coalesce_usecs;
+
+		/* static value of interrupt rate */
+		adapter->tx_itr_setting = adapter->tx_eitr_param;
+
+		/* clear the lower bit as its used for dynamic state */
+		adapter->tx_itr_setting &= ~1;
+	} else if (ec->tx_coalesce_usecs == 1) {
+		/* 1 means dynamic mode */
+		adapter->tx_eitr_param = 10000;
+		adapter->tx_itr_setting = 1;
+	} else {
+		adapter->tx_eitr_param = IXGBE_MAX_INT_RATE;
+		adapter->tx_itr_setting = 0;
 	}
 
 	/* MSI/MSIx Interrupt Mode */
@@ -1992,17 +2039,17 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 		for (i = 0; i < num_vectors; i++) {
 			q_vector = adapter->q_vector[i];
 			if (q_vector->txr_count && !q_vector->rxr_count)
-				/* tx vector gets half the rate */
-				q_vector->eitr = (adapter->eitr_param >> 1);
+				/* tx only */
+				q_vector->eitr = adapter->tx_eitr_param;
 			else
 				/* rx only or mixed */
-				q_vector->eitr = adapter->eitr_param;
+				q_vector->eitr = adapter->rx_eitr_param;
 			ixgbe_write_eitr(q_vector);
 		}
 	/* Legacy Interrupt Mode */
 	} else {
 		q_vector = adapter->q_vector[0];
-		q_vector->eitr = adapter->eitr_param;
+		q_vector->eitr = adapter->rx_eitr_param;
 		ixgbe_write_eitr(q_vector);
 	}
 
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 59ad959..c407bd9 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -926,12 +926,12 @@ static void ixgbe_configure_msix(struct ixgbe_adapter *adapter)
 			                      r_idx + 1);
 		}
 
-		/* if this is a tx only vector halve the interrupt rate */
 		if (q_vector->txr_count && !q_vector->rxr_count)
-			q_vector->eitr = (adapter->eitr_param >> 1);
+			/* tx only */
+			q_vector->eitr = adapter->tx_eitr_param;
 		else if (q_vector->rxr_count)
-			/* rx only */
-			q_vector->eitr = adapter->eitr_param;
+			/* rx or mixed */
+			q_vector->eitr = adapter->rx_eitr_param;
 
 		ixgbe_write_eitr(q_vector);
 	}
@@ -1359,7 +1359,7 @@ static int ixgbe_clean_rxonly(struct napi_struct *napi, int budget)
 	/* If all Rx work done, exit the polling mode */
 	if (work_done < budget) {
 		napi_complete(napi);
-		if (adapter->itr_setting & 1)
+		if (adapter->rx_itr_setting & 1)
 			ixgbe_set_itr_msix(q_vector);
 		if (!test_bit(__IXGBE_DOWN, &adapter->state))
 			ixgbe_irq_enable_queues(adapter,
@@ -1420,7 +1420,7 @@ static int ixgbe_clean_rxtx_many(struct napi_struct *napi, int budget)
 	/* If all Rx work done, exit the polling mode */
 	if (work_done < budget) {
 		napi_complete(napi);
-		if (adapter->itr_setting & 1)
+		if (adapter->rx_itr_setting & 1)
 			ixgbe_set_itr_msix(q_vector);
 		if (!test_bit(__IXGBE_DOWN, &adapter->state))
 			ixgbe_irq_enable_queues(adapter,
@@ -1458,10 +1458,10 @@ static int ixgbe_clean_txonly(struct napi_struct *napi, int budget)
 	if (!ixgbe_clean_tx_irq(q_vector, tx_ring))
 		work_done = budget;
 
-	/* If all Rx work done, exit the polling mode */
+	/* If all Tx work done, exit the polling mode */
 	if (work_done < budget) {
 		napi_complete(napi);
-		if (adapter->itr_setting & 1)
+		if (adapter->tx_itr_setting & 1)
 			ixgbe_set_itr_msix(q_vector);
 		if (!test_bit(__IXGBE_DOWN, &adapter->state))
 			ixgbe_irq_enable_queues(adapter, ((u64)1 << q_vector->v_idx));
@@ -1848,7 +1848,7 @@ static void ixgbe_configure_msi_and_legacy(struct ixgbe_adapter *adapter)
 	struct ixgbe_hw *hw = &adapter->hw;
 
 	IXGBE_WRITE_REG(hw, IXGBE_EITR(0),
-	                EITR_INTS_PER_SEC_TO_REG(adapter->eitr_param));
+	                EITR_INTS_PER_SEC_TO_REG(adapter->rx_eitr_param));
 
 	ixgbe_set_ivar(adapter, 0, 0, 0);
 	ixgbe_set_ivar(adapter, 1, 0, 0);
@@ -1970,6 +1970,50 @@ static u32 ixgbe_setup_mrqc(struct ixgbe_adapter *adapter)
 }
 
 /**
+ * ixgbe_configure_rscctl - enable RSC for the indicated ring
+ * @adapter:    address of board private structure
+ * @index:      index of ring to set
+ * @rx_buf_len: rx buffer length
+ **/
+static void ixgbe_configure_rscctl(struct ixgbe_adapter *adapter, int index,
+                                   int rx_buf_len)
+{
+	struct ixgbe_ring *rx_ring;
+	struct ixgbe_hw *hw = &adapter->hw;
+	int j;
+	u32 rscctrl;
+
+	rx_ring = &adapter->rx_ring[index];
+	j = rx_ring->reg_idx;
+	rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j));
+	rscctrl |= IXGBE_RSCCTL_RSCEN;
+	/*
+	 * we must limit the number of descriptors so that the
+	 * total size of max desc * buf_len is not greater
+	 * than 65535
+	 */
+	if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
+#if (MAX_SKB_FRAGS > 16)
+		rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
+#elif (MAX_SKB_FRAGS > 8)
+		rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
+#elif (MAX_SKB_FRAGS > 4)
+		rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
+#else
+		rscctrl |= IXGBE_RSCCTL_MAXDESC_1;
+#endif
+	} else {
+		if (rx_buf_len < IXGBE_RXBUFFER_4096)
+			rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
+		else if (rx_buf_len < IXGBE_RXBUFFER_8192)
+			rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
+		else
+			rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
+	}
+	IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(j), rscctrl);
+}
+
+/**
  * ixgbe_configure_rx - Configure 8259x Receive Unit after Reset
  * @adapter: board private structure
  *
@@ -1990,7 +2034,6 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 	u32 fctrl, hlreg0;
 	u32 reta = 0, mrqc = 0;
 	u32 rdrxctl;
-	u32 rscctrl;
 	int rx_buf_len;
 
 	/* Decide whether to use packet split mode or not */
@@ -2148,36 +2191,9 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 
 	if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) {
 		/* Enable 82599 HW-RSC */
-		for (i = 0; i < adapter->num_rx_queues; i++) {
-			rx_ring = &adapter->rx_ring[i];
-			j = rx_ring->reg_idx;
-			rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j));
-			rscctrl |= IXGBE_RSCCTL_RSCEN;
-			/*
-			 * we must limit the number of descriptors so that the
-			 * total size of max desc * buf_len is not greater
-			 * than 65535
-			 */
-			if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
-#if (MAX_SKB_FRAGS > 16)
-				rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
-#elif (MAX_SKB_FRAGS > 8)
-				rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
-#elif (MAX_SKB_FRAGS > 4)
-				rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
-#else
-				rscctrl |= IXGBE_RSCCTL_MAXDESC_1;
-#endif
-			} else {
-				if (rx_buf_len < IXGBE_RXBUFFER_4096)
-					rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
-				else if (rx_buf_len < IXGBE_RXBUFFER_8192)
-					rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
-				else
-					rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
-			}
-			IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(j), rscctrl);
-		}
+		for (i = 0; i < adapter->num_rx_queues; i++)
+			ixgbe_configure_rscctl(adapter, i, rx_buf_len);
+
 		/* Disable RSC for ACK packets */
 		IXGBE_WRITE_REG(hw, IXGBE_RSCDBU,
 		   (IXGBE_RSCDBU_RSCACKDIS | IXGBE_READ_REG(hw, IXGBE_RSCDBU)));
@@ -2926,6 +2942,8 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
 
 	ixgbe_napi_disable_all(adapter);
 
+	clear_bit(__IXGBE_SFP_MODULE_NOT_FOUND, &adapter->state);
+	del_timer_sync(&adapter->sfp_timer);
 	del_timer_sync(&adapter->watchdog_timer);
 	cancel_work_sync(&adapter->watchdog_task);
 
@@ -2989,7 +3007,7 @@ static int ixgbe_poll(struct napi_struct *napi, int budget)
 	/* If budget not fully consumed, exit the polling mode */
 	if (work_done < budget) {
 		napi_complete(napi);
-		if (adapter->itr_setting & 1)
+		if (adapter->rx_itr_setting & 1)
 			ixgbe_set_itr(adapter);
 		if (!test_bit(__IXGBE_DOWN, &adapter->state))
 			ixgbe_irq_enable_queues(adapter, IXGBE_EIMS_RTX_QUEUE);
@@ -3599,7 +3617,10 @@ static int ixgbe_alloc_q_vectors(struct ixgbe_adapter *adapter)
 		if (!q_vector)
 			goto err_out;
 		q_vector->adapter = adapter;
-		q_vector->eitr = adapter->eitr_param;
+		if (q_vector->txr_count && !q_vector->rxr_count)
+			q_vector->eitr = adapter->tx_eitr_param;
+		else
+			q_vector->eitr = adapter->rx_eitr_param;
 		q_vector->v_idx = q_idx;
 		netif_napi_add(adapter->netdev, &q_vector->napi, (*poll), 64);
 		adapter->q_vector[q_idx] = q_vector;
@@ -3868,8 +3889,10 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
 	hw->fc.disable_fc_autoneg = false;
 
 	/* enable itr by default in dynamic mode */
-	adapter->itr_setting = 1;
-	adapter->eitr_param = 20000;
+	adapter->rx_itr_setting = 1;
+	adapter->rx_eitr_param = 20000;
+	adapter->tx_itr_setting = 1;
+	adapter->tx_eitr_param = 10000;
 
 	/* set defaults for eitr in MegaBytes */
 	adapter->eitr_low = 10;
diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index f7bdde1..b5aa974 100644
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -1469,6 +1469,7 @@ netxen_nic_resume(struct pci_dev *pdev)
 	}
 
 	netxen_schedule_work(adapter, netxen_fw_poll_work, FW_POLL_DELAY);
+	return 0;
 
 err_out_detach:
 	netxen_nic_detach(adapter);
@@ -1903,12 +1904,13 @@ static void netxen_tx_timeout_task(struct work_struct *work)
 
 		netif_wake_queue(adapter->netdev);
 
-		goto done;
+		clear_bit(__NX_RESETTING, &adapter->state);
 
 	} else {
+		clear_bit(__NX_RESETTING, &adapter->state);
 		if (!netxen_nic_reset_context(adapter)) {
 			adapter->netdev->trans_start = jiffies;
-			goto done;
+			return;
 		}
 
 		/* context reset failed, fall through for fw reset */
@@ -1916,8 +1918,6 @@ static void netxen_tx_timeout_task(struct work_struct *work)
 
 request_reset:
 	adapter->need_fw_reset = 1;
-done:
-	clear_bit(__NX_RESETTING, &adapter->state);
 }
 
 struct net_device_stats *netxen_nic_get_stats(struct net_device *netdev)
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index 97db1c7..474876c 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -340,12 +340,11 @@ static hw_info_t *get_hwinfo(struct pcmcia_device *link)
 	base = &virt[hw_info[i].offset & (req.Size-1)];
 	if ((readb(base+0) == hw_info[i].a0) &&
 	    (readb(base+2) == hw_info[i].a1) &&
-	    (readb(base+4) == hw_info[i].a2))
-	    break;
-    }
-    if (i < NR_INFO) {
-	for (j = 0; j < 6; j++)
-	    dev->dev_addr[j] = readb(base + (j<<1));
+	    (readb(base+4) == hw_info[i].a2)) {
+		for (j = 0; j < 6; j++)
+		    dev->dev_addr[j] = readb(base + (j<<1));
+		break;
+	}
     }
 
     iounmap(virt);
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 15140f9..ef11657 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1497,7 +1497,6 @@ static int sky2_up(struct net_device *dev)
 	if (ramsize > 0) {
 		u32 rxspace;
 
-		hw->flags |= SKY2_HW_RAM_BUFFER;
 		pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize);
 		if (ramsize < 16)
 			rxspace = ramsize / 2;
@@ -2926,6 +2925,9 @@ static int __devinit sky2_init(struct sky2_hw *hw)
 			++hw->ports;
 	}
 
+	if (sky2_read8(hw, B2_E_0))
+		hw->flags |= SKY2_HW_RAM_BUFFER;
+
 	return 0;
 }
 
diff --git a/drivers/net/sunvnet.c b/drivers/net/sunvnet.c
index f1e5e45..bc74db0 100644
--- a/drivers/net/sunvnet.c
+++ b/drivers/net/sunvnet.c
@@ -1016,7 +1016,6 @@ static const struct net_device_ops vnet_ops = {
 	.ndo_open		= vnet_open,
 	.ndo_stop		= vnet_close,
 	.ndo_set_multicast_list	= vnet_set_rx_mode,
-	.ndo_change_mtu		= eth_change_mtu,
 	.ndo_set_mac_address	= vnet_set_mac_addr,
 	.ndo_validate_addr	= eth_validate_addr,
 	.ndo_tx_timeout		= vnet_tx_timeout,
diff --git a/drivers/net/tun.c b/drivers/net/tun.c
index d3ee199..4fdfa2a 100644
--- a/drivers/net/tun.c
+++ b/drivers/net/tun.c
@@ -946,8 +946,6 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr)
 		char *name;
 		unsigned long flags = 0;
 
-		err = -EINVAL;
-
 		if (!capable(CAP_NET_ADMIN))
 			return -EPERM;
 		err = security_tun_dev_create();
@@ -964,7 +962,7 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr)
 			flags |= TUN_TAP_DEV;
 			name = "tap%d";
 		} else
-			goto failed;
+			return -EINVAL;
 
 		if (*ifr->ifr_name)
 			name = ifr->ifr_name;
diff --git a/drivers/net/usb/kaweth.c b/drivers/net/usb/kaweth.c
index e2a39b9..e391ef9 100644
--- a/drivers/net/usb/kaweth.c
+++ b/drivers/net/usb/kaweth.c
@@ -263,6 +263,7 @@ static int kaweth_control(struct kaweth_device *kaweth,
 			  int timeout)
 {
 	struct usb_ctrlrequest *dr;
+	int retval;
 
 	dbg("kaweth_control()");
 
@@ -278,18 +279,21 @@ static int kaweth_control(struct kaweth_device *kaweth,
 		return -ENOMEM;
 	}
 
-	dr->bRequestType= requesttype;
+	dr->bRequestType = requesttype;
 	dr->bRequest = request;
 	dr->wValue = cpu_to_le16(value);
 	dr->wIndex = cpu_to_le16(index);
 	dr->wLength = cpu_to_le16(size);
 
-	return kaweth_internal_control_msg(kaweth->dev,
-					pipe,
-					dr,
-					data,
-					size,
-					timeout);
+	retval = kaweth_internal_control_msg(kaweth->dev,
+					     pipe,
+					     dr,
+					     data,
+					     size,
+					     timeout);
+
+	kfree(dr);
+	return retval;
 }
 
 /****************************************************************
diff --git a/drivers/net/usb/smsc95xx.c b/drivers/net/usb/smsc95xx.c
index 938fb35..c6c9222 100644
--- a/drivers/net/usb/smsc95xx.c
+++ b/drivers/net/usb/smsc95xx.c
@@ -1227,7 +1227,7 @@ static const struct driver_info smsc95xx_info = {
 	.rx_fixup	= smsc95xx_rx_fixup,
 	.tx_fixup	= smsc95xx_tx_fixup,
 	.status		= smsc95xx_status,
-	.flags		= FLAG_ETHER,
+	.flags		= FLAG_ETHER | FLAG_SEND_ZLP,
 };
 
 static const struct usb_device_id products[] = {
@@ -1237,10 +1237,75 @@ static const struct usb_device_id products[] = {
 		.driver_info = (unsigned long) &smsc95xx_info,
 	},
 	{
+		/* SMSC9505 USB Ethernet Device */
+		USB_DEVICE(0x0424, 0x9505),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9500A USB Ethernet Device */
+		USB_DEVICE(0x0424, 0x9E00),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9505A USB Ethernet Device */
+		USB_DEVICE(0x0424, 0x9E01),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
 		/* SMSC9512/9514 USB Hub & Ethernet Device */
 		USB_DEVICE(0x0424, 0xec00),
 		.driver_info = (unsigned long) &smsc95xx_info,
 	},
+	{
+		/* SMSC9500 USB Ethernet Device (SAL10) */
+		USB_DEVICE(0x0424, 0x9900),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9505 USB Ethernet Device (SAL10) */
+		USB_DEVICE(0x0424, 0x9901),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9500A USB Ethernet Device (SAL10) */
+		USB_DEVICE(0x0424, 0x9902),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9505A USB Ethernet Device (SAL10) */
+		USB_DEVICE(0x0424, 0x9903),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9512/9514 USB Hub & Ethernet Device (SAL10) */
+		USB_DEVICE(0x0424, 0x9904),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9500A USB Ethernet Device (HAL) */
+		USB_DEVICE(0x0424, 0x9905),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9505A USB Ethernet Device (HAL) */
+		USB_DEVICE(0x0424, 0x9906),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9500 USB Ethernet Device (Alternate ID) */
+		USB_DEVICE(0x0424, 0x9907),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9500A USB Ethernet Device (Alternate ID) */
+		USB_DEVICE(0x0424, 0x9908),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
+	{
+		/* SMSC9512/9514 USB Hub & Ethernet Device (Alternate ID) */
+		USB_DEVICE(0x0424, 0x9909),
+		.driver_info = (unsigned long) &smsc95xx_info,
+	},
 	{ },		/* END */
 };
 MODULE_DEVICE_TABLE(usb, products);
diff --git a/drivers/net/usb/usbnet.c b/drivers/net/usb/usbnet.c
index 24b36f7..ca5ca5a 100644
--- a/drivers/net/usb/usbnet.c
+++ b/drivers/net/usb/usbnet.c
@@ -1049,7 +1049,7 @@ netdev_tx_t usbnet_start_xmit (struct sk_buff *skb,
 	 * NOTE:  strictly conforming cdc-ether devices should expect
 	 * the ZLP here, but ignore the one-byte packet.
 	 */
-	if ((length % dev->maxpacket) == 0) {
+	if (!(info->flags & FLAG_SEND_ZLP) && (length % dev->maxpacket) == 0) {
 		urb->transfer_buffer_length++;
 		if (skb_tailroom(skb)) {
 			skb->data[skb->len] = 0;
diff --git a/drivers/net/wireless/ath/ar9170/usb.c b/drivers/net/wireless/ath/ar9170/usb.c
index e0138ac..e974e58 100644
--- a/drivers/net/wireless/ath/ar9170/usb.c
+++ b/drivers/net/wireless/ath/ar9170/usb.c
@@ -64,6 +64,8 @@ static struct usb_device_id ar9170_usb_ids[] = {
 	{ USB_DEVICE(0x0cf3, 0x9170) },
 	/* Atheros TG121N */
 	{ USB_DEVICE(0x0cf3, 0x1001) },
+	/* TP-Link TL-WN821N v2 */
+	{ USB_DEVICE(0x0cf3, 0x1002) },
 	/* Cace Airpcap NX */
 	{ USB_DEVICE(0xcace, 0x0300) },
 	/* D-Link DWA 160A */
diff --git a/drivers/net/wireless/ath/ath9k/calib.c b/drivers/net/wireless/ath/ath9k/calib.c
index 3234995..0ad6d0b 100644
--- a/drivers/net/wireless/ath/ath9k/calib.c
+++ b/drivers/net/wireless/ath/ath9k/calib.c
@@ -609,14 +609,24 @@ void ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
 		AR_PHY_CH1_EXT_CCA,
 		AR_PHY_CH2_EXT_CCA
 	};
-	u8 chainmask;
+	u8 chainmask, rx_chain_status;
 
+	rx_chain_status = REG_READ(ah, AR_PHY_RX_CHAINMASK);
 	if (AR_SREV_9285(ah))
 		chainmask = 0x9;
-	else if (AR_SREV_9280(ah) || AR_SREV_9287(ah))
-		chainmask = 0x1B;
-	else
-		chainmask = 0x3F;
+	else if (AR_SREV_9280(ah) || AR_SREV_9287(ah)) {
+		if ((rx_chain_status & 0x2) || (rx_chain_status & 0x4))
+			chainmask = 0x1B;
+		else
+			chainmask = 0x09;
+	} else {
+		if (rx_chain_status & 0x4)
+			chainmask = 0x3F;
+		else if (rx_chain_status & 0x2)
+			chainmask = 0x1B;
+		else
+			chainmask = 0x09;
+	}
 
 	h = ah->nfCalHist;
 
@@ -697,6 +707,8 @@ void ath9k_init_nfcal_hist_buffer(struct ath_hw *ah)
 		noise_floor = AR_PHY_CCA_MAX_AR9280_GOOD_VALUE;
 	else if (AR_SREV_9285(ah))
 		noise_floor = AR_PHY_CCA_MAX_AR9285_GOOD_VALUE;
+	else if (AR_SREV_9287(ah))
+		noise_floor = AR_PHY_CCA_MAX_AR9287_GOOD_VALUE;
 	else
 		noise_floor = AR_PHY_CCA_MAX_AR5416_GOOD_VALUE;
 
@@ -924,6 +936,7 @@ static inline void ath9k_hw_9285_pa_cal(struct ath_hw *ah, bool is_reset)
 		regVal |= (1 << (19 + i));
 		REG_WRITE(ah, 0x7834, regVal);
 		udelay(1);
+		regVal = REG_READ(ah, 0x7834);
 		regVal &= (~(0x1 << (19 + i)));
 		reg_field = MS(REG_READ(ah, 0x7840), AR9285_AN_RXTXBB1_SPARE9);
 		regVal |= (reg_field << (19 + i));
diff --git a/drivers/net/wireless/ath/ath9k/calib.h b/drivers/net/wireless/ath/ath9k/calib.h
index 019bcbb..9028ab1 100644
--- a/drivers/net/wireless/ath/ath9k/calib.h
+++ b/drivers/net/wireless/ath/ath9k/calib.h
@@ -28,6 +28,7 @@ extern const struct ath9k_percal_data adc_init_dc_cal;
 #define AR_PHY_CCA_MAX_AR5416_GOOD_VALUE	-85
 #define AR_PHY_CCA_MAX_AR9280_GOOD_VALUE	-112
 #define AR_PHY_CCA_MAX_AR9285_GOOD_VALUE	-118
+#define AR_PHY_CCA_MAX_AR9287_GOOD_VALUE	-118
 #define AR_PHY_CCA_MAX_HIGH_VALUE      		-62
 #define AR_PHY_CCA_MIN_BAD_VALUE       		-140
 #define AR_PHY_CCA_FILTERWINDOW_LENGTH_INIT     3
diff --git a/drivers/net/wireless/ath/ath9k/eeprom_def.c b/drivers/net/wireless/ath/ath9k/eeprom_def.c
index ae7fb5d..4071fc9 100644
--- a/drivers/net/wireless/ath/ath9k/eeprom_def.c
+++ b/drivers/net/wireless/ath/ath9k/eeprom_def.c
@@ -509,6 +509,8 @@ static void ath9k_hw_def_set_board_values(struct ath_hw *ah,
 			REG_RMW_FIELD(ah, AR_AN_TOP1, AR_AN_TOP1_DACIPMODE,
 				      eep->baseEepHeader.dacLpMode);
 
+		udelay(100);
+
 		REG_RMW_FIELD(ah, AR_PHY_FRAME_CTL, AR_PHY_FRAME_CTL_TX_CLIP,
 			      pModal->miscBits >> 2);
 
@@ -902,7 +904,7 @@ static void ath9k_hw_set_def_power_per_rate_table(struct ath_hw *ah,
 						  u16 powerLimit)
 {
 #define REDUCE_SCALED_POWER_BY_TWO_CHAIN     6  /* 10*log10(2)*2 */
-#define REDUCE_SCALED_POWER_BY_THREE_CHAIN   10 /* 10*log10(3)*2 */
+#define REDUCE_SCALED_POWER_BY_THREE_CHAIN   9 /* 10*log10(3)*2 */
 
 	struct ath_regulatory *regulatory = ath9k_hw_regulatory(ah);
 	struct ar5416_eeprom_def *pEepData = &ah->eeprom.def;
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index b6c6cca..ca7694c 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -842,7 +842,7 @@ static void ath9k_hw_init_mode_regs(struct ath_hw *ah)
 
 static void ath9k_hw_init_mode_gain_regs(struct ath_hw *ah)
 {
-	if (AR_SREV_9287_11(ah))
+	if (AR_SREV_9287_11_OR_LATER(ah))
 		INIT_INI_ARRAY(&ah->iniModesRxGain,
 		ar9287Modes_rx_gain_9287_1_1,
 		ARRAY_SIZE(ar9287Modes_rx_gain_9287_1_1), 6);
@@ -853,7 +853,7 @@ static void ath9k_hw_init_mode_gain_regs(struct ath_hw *ah)
 	else if (AR_SREV_9280_20(ah))
 		ath9k_hw_init_rxgain_ini(ah);
 
-	if (AR_SREV_9287_11(ah)) {
+	if (AR_SREV_9287_11_OR_LATER(ah)) {
 		INIT_INI_ARRAY(&ah->iniModesTxGain,
 		ar9287Modes_tx_gain_9287_1_1,
 		ARRAY_SIZE(ar9287Modes_tx_gain_9287_1_1), 6);
@@ -965,7 +965,7 @@ int ath9k_hw_init(struct ath_hw *ah)
 	ath9k_hw_init_mode_regs(ah);
 
 	if (ah->is_pciexpress)
-		ath9k_hw_configpcipowersave(ah, 0);
+		ath9k_hw_configpcipowersave(ah, 0, 0);
 	else
 		ath9k_hw_disablepcie(ah);
 
@@ -1273,6 +1273,15 @@ static void ath9k_hw_override_ini(struct ath_hw *ah,
 	 */
 	REG_SET_BIT(ah, AR_DIAG_SW, (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT));
 
+	if (AR_SREV_9280_10_OR_LATER(ah)) {
+		val = REG_READ(ah, AR_PCU_MISC_MODE2) &
+			       (~AR_PCU_MISC_MODE2_HWWAR1);
+
+		if (AR_SREV_9287_10_OR_LATER(ah))
+			val = val & (~AR_PCU_MISC_MODE2_HWWAR2);
+
+		REG_WRITE(ah, AR_PCU_MISC_MODE2, val);
+	}
 
 	if (!AR_SREV_5416_20_OR_LATER(ah) ||
 	    AR_SREV_9280_10_OR_LATER(ah))
@@ -1784,7 +1793,7 @@ static void ath9k_hw_set_regs(struct ath_hw *ah, struct ath9k_channel *chan,
 static bool ath9k_hw_chip_reset(struct ath_hw *ah,
 				struct ath9k_channel *chan)
 {
-	if (OLC_FOR_AR9280_20_LATER) {
+	if (AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL)) {
 		if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_POWER_ON))
 			return false;
 	} else if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_WARM))
@@ -2338,6 +2347,7 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 	struct ath9k_channel *curchan = ah->curchan;
 	u32 saveDefAntenna;
 	u32 macStaId1;
+	u64 tsf = 0;
 	int i, rx_chainmask, r;
 
 	ah->extprotspacing = sc->ht_extprotspacing;
@@ -2347,7 +2357,7 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 	if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
 		return -EIO;
 
-	if (curchan)
+	if (curchan && !ah->chip_fullsleep)
 		ath9k_hw_getnf(ah, curchan);
 
 	if (bChannelChange &&
@@ -2356,8 +2366,8 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 	    (chan->channel != ah->curchan->channel) &&
 	    ((chan->channelFlags & CHANNEL_ALL) ==
 	     (ah->curchan->channelFlags & CHANNEL_ALL)) &&
-	    (!AR_SREV_9280(ah) || (!IS_CHAN_A_5MHZ_SPACED(chan) &&
-				   !IS_CHAN_A_5MHZ_SPACED(ah->curchan)))) {
+	     !(AR_SREV_9280(ah) || IS_CHAN_A_5MHZ_SPACED(chan) ||
+	     IS_CHAN_A_5MHZ_SPACED(ah->curchan))) {
 
 		if (ath9k_hw_channel_change(ah, chan, sc->tx_chan_width)) {
 			ath9k_hw_loadnf(ah, ah->curchan);
@@ -2372,6 +2382,10 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 
 	macStaId1 = REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_BASE_RATE_11B;
 
+	/* For chips on which RTC reset is done, save TSF before it gets cleared */
+	if (AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL))
+		tsf = ath9k_hw_gettsf64(ah);
+
 	saveLedState = REG_READ(ah, AR_CFG_LED) &
 		(AR_CFG_LED_ASSOC_CTL | AR_CFG_LED_MODE_SEL |
 		 AR_CFG_LED_BLINK_THRESH_SEL | AR_CFG_LED_BLINK_SLOW);
@@ -2398,6 +2412,10 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 		udelay(50);
 	}
 
+	/* Restore TSF */
+	if (tsf && AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL))
+		ath9k_hw_settsf64(ah, tsf);
+
 	if (AR_SREV_9280_10_OR_LATER(ah))
 		REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL, AR_GPIO_JTAG_DISABLE);
 
@@ -3005,9 +3023,10 @@ void ath9k_ps_restore(struct ath_softc *sc)
  * Programming the SerDes must go through the same 288 bit serial shift
  * register as the other analog registers.  Hence the 9 writes.
  */
-void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
+void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore, int power_off)
 {
 	u8 i;
+	u32 val;
 
 	if (ah->is_pciexpress != true)
 		return;
@@ -3017,84 +3036,113 @@ void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
 		return;
 
 	/* Nothing to do on restore for 11N */
-	if (restore)
-		return;
+	if (!restore) {
+		if (AR_SREV_9280_20_OR_LATER(ah)) {
+			/*
+			 * AR9280 2.0 or later chips use SerDes values from the
+			 * initvals.h initialized depending on chipset during
+			 * ath9k_hw_init()
+			 */
+			for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) {
+				REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0),
+					  INI_RA(&ah->iniPcieSerdes, i, 1));
+			}
+		} else if (AR_SREV_9280(ah) &&
+			   (ah->hw_version.macRev == AR_SREV_REVISION_9280_10)) {
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+
+			/* RX shut off when elecidle is asserted */
+			REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560);
+
+			/* Shut off CLKREQ active in L1 */
+			if (ah->config.pcie_clock_req)
+				REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc);
+			else
+				REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd);
 
-	if (AR_SREV_9280_20_OR_LATER(ah)) {
-		/*
-		 * AR9280 2.0 or later chips use SerDes values from the
-		 * initvals.h initialized depending on chipset during
-		 * ath9k_hw_init()
-		 */
-		for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) {
-			REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0),
-				  INI_RA(&ah->iniPcieSerdes, i, 1));
-		}
-	} else if (AR_SREV_9280(ah) &&
-		   (ah->hw_version.macRev == AR_SREV_REVISION_9280_10)) {
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007);
 
-		/* RX shut off when elecidle is asserted */
-		REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560);
+			/* Load the new settings */
+			REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
 
-		/* Shut off CLKREQ active in L1 */
-		if (ah->config.pcie_clock_req)
-			REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc);
-		else
-			REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd);
-
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007);
+		} else {
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
 
-		/* Load the new settings */
-		REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+			/* RX shut off when elecidle is asserted */
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
 
-	} else {
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+			/*
+			 * Ignore ah->ah_config.pcie_clock_req setting for
+			 * pre-AR9280 11n
+			 */
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
 
-		/* RX shut off when elecidle is asserted */
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+			REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
 
-		/*
-		 * Ignore ah->ah_config.pcie_clock_req setting for
-		 * pre-AR9280 11n
-		 */
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
+			/* Load the new settings */
+			REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+		}
 
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
-		REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
+		udelay(1000);
 
-		/* Load the new settings */
-		REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
-	}
+		/* set bit 19 to allow forcing of pcie core into L1 state */
+		REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
 
-	udelay(1000);
+		/* Several PCIe massages to ensure proper behaviour */
+		if (ah->config.pcie_waen) {
+			val = ah->config.pcie_waen;
+			if (!power_off)
+				val &= (~AR_WA_D3_L1_DISABLE);
+		} else {
+			if (AR_SREV_9285(ah) || AR_SREV_9271(ah) ||
+			    AR_SREV_9287(ah)) {
+				val = AR9285_WA_DEFAULT;
+				if (!power_off)
+					val &= (~AR_WA_D3_L1_DISABLE);
+			} else if (AR_SREV_9280(ah)) {
+				/*
+				 * On AR9280 chips bit 22 of 0x4004 needs to be
+				 * set otherwise card may disappear.
+				 */
+				val = AR9280_WA_DEFAULT;
+				if (!power_off)
+					val &= (~AR_WA_D3_L1_DISABLE);
+			} else
+				val = AR_WA_DEFAULT;
+		}
 
-	/* set bit 19 to allow forcing of pcie core into L1 state */
-	REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
+		REG_WRITE(ah, AR_WA, val);
+	}
 
-	/* Several PCIe massages to ensure proper behaviour */
-	if (ah->config.pcie_waen) {
-		REG_WRITE(ah, AR_WA, ah->config.pcie_waen);
-	} else {
-		if (AR_SREV_9285(ah) || AR_SREV_9271(ah) || AR_SREV_9287(ah))
-			REG_WRITE(ah, AR_WA, AR9285_WA_DEFAULT);
+	if (power_off) {
 		/*
-		 * On AR9280 chips bit 22 of 0x4004 needs to be set to
-		 * otherwise card may disappear.
+		 * Set PCIe workaround bits
+		 * bit 14 in WA register (disable L1) should only
+		 * be set when device enters D3 and be cleared
+		 * when device comes back to D0.
 		 */
-		else if (AR_SREV_9280(ah))
-			REG_WRITE(ah, AR_WA, AR9280_WA_DEFAULT);
-		else
-			REG_WRITE(ah, AR_WA, AR_WA_DEFAULT);
+		if (ah->config.pcie_waen) {
+			if (ah->config.pcie_waen & AR_WA_D3_L1_DISABLE)
+				REG_SET_BIT(ah, AR_WA, AR_WA_D3_L1_DISABLE);
+		} else {
+			if (((AR_SREV_9285(ah) || AR_SREV_9271(ah) ||
+			      AR_SREV_9287(ah)) &&
+			     (AR9285_WA_DEFAULT & AR_WA_D3_L1_DISABLE)) ||
+			    (AR_SREV_9280(ah) &&
+			     (AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE))) {
+				REG_SET_BIT(ah, AR_WA, AR_WA_D3_L1_DISABLE);
+			}
+		}
 	}
 }
 
@@ -3652,15 +3700,7 @@ void ath9k_hw_fill_cap_info(struct ath_hw *ah)
 	}
 #endif
 
-	if ((ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCI) ||
-	    (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE) ||
-	    (ah->hw_version.macVersion == AR_SREV_VERSION_9160) ||
-	    (ah->hw_version.macVersion == AR_SREV_VERSION_9100) ||
-	    (ah->hw_version.macVersion == AR_SREV_VERSION_9280) ||
-	    (ah->hw_version.macVersion == AR_SREV_VERSION_9285))
-		pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP;
-	else
-		pCap->hw_caps |= ATH9K_HW_CAP_AUTOSLEEP;
+	pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP;
 
 	if (AR_SREV_9280(ah) || AR_SREV_9285(ah))
 		pCap->hw_caps &= ~ATH9K_HW_CAP_4KB_SPLITTRANS;
diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h
index 9106a0b..b892345 100644
--- a/drivers/net/wireless/ath/ath9k/hw.h
+++ b/drivers/net/wireless/ath/ath9k/hw.h
@@ -106,7 +106,7 @@
 #define AH_TSF_WRITE_TIMEOUT        100    /* (us) */
 #define AH_TIME_QUANTUM             10
 #define AR_KEYTABLE_SIZE            128
-#define POWER_UP_TIME               200000
+#define POWER_UP_TIME               10000
 #define SPUR_RSSI_THRESH            40
 
 #define CAB_TIMEOUT_VAL             10
@@ -650,7 +650,7 @@ void ath9k_hw_set_sta_beacon_timers(struct ath_hw *ah,
 				    const struct ath9k_beacon_state *bs);
 bool ath9k_hw_setpower(struct ath_hw *ah,
 		       enum ath9k_power_mode mode);
-void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore);
+void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore, int power_off);
 
 /* Interrupt Handling */
 bool ath9k_hw_intrpend(struct ath_hw *ah);
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index 3dc7b5a..52bed89 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1131,7 +1131,7 @@ void ath_radio_enable(struct ath_softc *sc)
 	int r;
 
 	ath9k_ps_wakeup(sc);
-	ath9k_hw_configpcipowersave(ah, 0);
+	ath9k_hw_configpcipowersave(ah, 0, 0);
 
 	if (!ah->curchan)
 		ah->curchan = ath_get_curchannel(sc, sc->hw);
@@ -1202,7 +1202,7 @@ void ath_radio_disable(struct ath_softc *sc)
 	spin_unlock_bh(&sc->sc_resetlock);
 
 	ath9k_hw_phy_disable(ah);
-	ath9k_hw_configpcipowersave(ah, 1);
+	ath9k_hw_configpcipowersave(ah, 1, 1);
 	ath9k_ps_restore(sc);
 	ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP);
 }
@@ -1226,11 +1226,6 @@ static void ath9k_rfkill_poll_state(struct ieee80211_hw *hw)
 	bool blocked = !!ath_is_rfkill_set(sc);
 
 	wiphy_rfkill_set_hw_state(hw->wiphy, blocked);
-
-	if (blocked)
-		ath_radio_disable(sc);
-	else
-		ath_radio_enable(sc);
 }
 
 static void ath_start_rfkill_poll(struct ath_softc *sc)
@@ -1260,6 +1255,7 @@ void ath_detach(struct ath_softc *sc)
 	DPRINTF(sc, ATH_DBG_CONFIG, "Detach ATH hw\n");
 
 	ath_deinit_leds(sc);
+	wiphy_rfkill_stop_polling(sc->hw->wiphy);
 
 	for (i = 0; i < sc->num_sec_wiphy; i++) {
 		struct ath_wiphy *aphy = sc->sec_wiphy[i];
@@ -1942,7 +1938,7 @@ static int ath9k_start(struct ieee80211_hw *hw)
 	init_channel = ath_get_curchannel(sc, hw);
 
 	/* Reset SERDES registers */
-	ath9k_hw_configpcipowersave(sc->sc_ah, 0);
+	ath9k_hw_configpcipowersave(sc->sc_ah, 0, 0);
 
 	/*
 	 * The basic interface to setting the hardware in a good
@@ -2166,11 +2162,9 @@ static void ath9k_stop(struct ieee80211_hw *hw)
 	} else
 		sc->rx.rxlink = NULL;
 
-	wiphy_rfkill_stop_polling(sc->hw->wiphy);
-
 	/* disable HAL and put h/w to sleep */
 	ath9k_hw_disable(sc->sc_ah);
-	ath9k_hw_configpcipowersave(sc->sc_ah, 1);
+	ath9k_hw_configpcipowersave(sc->sc_ah, 1, 1);
 	ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_FULL_SLEEP);
 
 	sc->sc_flags |= SC_OP_INVALID;
diff --git a/drivers/net/wireless/ath/ath9k/reg.h b/drivers/net/wireless/ath/ath9k/reg.h
index e5c29eb..d83b77f8 100644
--- a/drivers/net/wireless/ath/ath9k/reg.h
+++ b/drivers/net/wireless/ath/ath9k/reg.h
@@ -676,8 +676,9 @@
 #define AR_RC_HOSTIF         0x00000100
 
 #define AR_WA                		0x4004
+#define AR_WA_D3_L1_DISABLE		(1 << 14)
 #define AR9285_WA_DEFAULT 		0x004a05cb
-#define AR9280_WA_DEFAULT           	0x0040073f
+#define AR9280_WA_DEFAULT           	0x0040073b
 #define AR_WA_DEFAULT               	0x0000073f
 
 
diff --git a/drivers/net/wireless/b43/Kconfig b/drivers/net/wireless/b43/Kconfig
index 83e3813..54ea61c 100644
--- a/drivers/net/wireless/b43/Kconfig
+++ b/drivers/net/wireless/b43/Kconfig
@@ -61,11 +61,28 @@ config B43_PCMCIA
 
 	  If unsure, say N.
 
+config B43_SDIO
+	bool "Broadcom 43xx SDIO device support (EXPERIMENTAL)"
+	depends on B43 && SSB_SDIOHOST_POSSIBLE && EXPERIMENTAL
+	select SSB_SDIOHOST
+	---help---
+	  Broadcom 43xx device support for Soft-MAC SDIO devices.
+
+	  With this config option you can drive Soft-MAC b43 cards with a
+	  Secure Digital I/O interface.
+	  This includes the WLAN daughter card found on the Nintendo Wii
+	  video game console.
+	  Note that this does not support Broadcom 43xx Full-MAC devices.
+
+	  It's safe to select Y here, even if you don't have a B43 SDIO device.
+
+	  If unsure, say N.
+
 # Data transfers to the device via PIO
-# This is only needed on PCMCIA devices. All others can do DMA properly.
+# This is only needed on PCMCIA and SDIO devices. All others can do DMA properly.
 config B43_PIO
 	bool
-	depends on B43 && (B43_PCMCIA || B43_FORCE_PIO)
+	depends on B43 && (B43_SDIO || B43_PCMCIA || B43_FORCE_PIO)
 	select SSB_BLOCKIO
 	default y
 
diff --git a/drivers/net/wireless/b43/Makefile b/drivers/net/wireless/b43/Makefile
index da379f4..84772a2 100644
--- a/drivers/net/wireless/b43/Makefile
+++ b/drivers/net/wireless/b43/Makefile
@@ -16,6 +16,7 @@ b43-$(CONFIG_B43_PIO)		+= pio.o
 b43-y				+= rfkill.o
 b43-$(CONFIG_B43_LEDS)		+= leds.o
 b43-$(CONFIG_B43_PCMCIA)	+= pcmcia.o
+b43-$(CONFIG_B43_SDIO)		+= sdio.o
 b43-$(CONFIG_B43_DEBUG)		+= debugfs.o
 
 obj-$(CONFIG_B43)		+= b43.o
diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h
index 09cfe68..fa1549a 100644
--- a/drivers/net/wireless/b43/b43.h
+++ b/drivers/net/wireless/b43/b43.h
@@ -629,13 +629,6 @@ struct b43_wl {
 	 * from the mac80211 subsystem. */
 	u16 mac80211_initially_registered_queues;
 
-	/* R/W lock for data transmission.
-	 * Transmissions on 2+ queues can run concurrently, but somebody else
-	 * might sync with TX by write_lock_irqsave()'ing. */
-	rwlock_t tx_lock;
-	/* Lock for LEDs access. */
-	spinlock_t leds_lock;
-
 	/* We can only have one operating interface (802.11 core)
 	 * at a time. General information about this interface follows.
 	 */
@@ -686,6 +679,9 @@ struct b43_wl {
 	struct work_struct tx_work;
 	/* Queue of packets to be transmitted. */
 	struct sk_buff_head tx_queue;
+
+	/* The device LEDs. */
+	struct b43_leds leds;
 };
 
 /* The type of the firmware file. */
@@ -768,13 +764,10 @@ struct b43_wldev {
 	/* The device initialization status.
 	 * Use b43_status() to query. */
 	atomic_t __init_status;
-	/* Saved init status for handling suspend. */
-	int suspend_init_status;
 
 	bool bad_frames_preempt;	/* Use "Bad Frames Preemption" (default off) */
 	bool dfq_valid;		/* Directed frame queue valid (IBSS PS mode, ATIM) */
 	bool radio_hw_enable;	/* saved state of radio hardware enabled state */
-	bool suspend_in_progress;	/* TRUE, if we are in a suspend/resume cycle */
 	bool qos_enabled;		/* TRUE, if QoS is used. */
 	bool hwcrypto_enabled;		/* TRUE, if HW crypto acceleration is enabled. */
 
@@ -794,12 +787,6 @@ struct b43_wldev {
 	/* Various statistics about the physical device. */
 	struct b43_stats stats;
 
-	/* The device LEDs. */
-	struct b43_led led_tx;
-	struct b43_led led_rx;
-	struct b43_led led_assoc;
-	struct b43_led led_radio;
-
 	/* Reason code of the last interrupt. */
 	u32 irq_reason;
 	u32 dma_reason[6];
@@ -830,6 +817,10 @@ struct b43_wldev {
 	/* Debugging stuff follows. */
 #ifdef CONFIG_B43_DEBUG
 	struct b43_dfsentry *dfsentry;
+	unsigned int irq_count;
+	unsigned int irq_bit_count[32];
+	unsigned int tx_count;
+	unsigned int rx_count;
 #endif
 };
 
diff --git a/drivers/net/wireless/b43/debugfs.c b/drivers/net/wireless/b43/debugfs.c
index 8f64943..80b19a4 100644
--- a/drivers/net/wireless/b43/debugfs.c
+++ b/drivers/net/wireless/b43/debugfs.c
@@ -689,6 +689,7 @@ static void b43_add_dynamic_debug(struct b43_wldev *dev)
 	add_dyn_dbg("debug_lo", B43_DBG_LO, 0);
 	add_dyn_dbg("debug_firmware", B43_DBG_FIRMWARE, 0);
 	add_dyn_dbg("debug_keys", B43_DBG_KEYS, 0);
+	add_dyn_dbg("debug_verbose_stats", B43_DBG_VERBOSESTATS, 0);
 
 #undef add_dyn_dbg
 }
diff --git a/drivers/net/wireless/b43/debugfs.h b/drivers/net/wireless/b43/debugfs.h
index e47b4b4..822aad8 100644
--- a/drivers/net/wireless/b43/debugfs.h
+++ b/drivers/net/wireless/b43/debugfs.h
@@ -13,6 +13,7 @@ enum b43_dyndbg {		/* Dynamic debugging features */
 	B43_DBG_LO,
 	B43_DBG_FIRMWARE,
 	B43_DBG_KEYS,
+	B43_DBG_VERBOSESTATS,
 	__B43_NR_DYNDBG,
 };
 
diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c
index a467ee2..8701034 100644
--- a/drivers/net/wireless/b43/dma.c
+++ b/drivers/net/wireless/b43/dma.c
@@ -1428,9 +1428,9 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev,
 				ring->nr_failed_tx_packets++;
 			ring->nr_total_packet_tries += status->frame_count;
 #endif /* DEBUG */
-			ieee80211_tx_status_irqsafe(dev->wl->hw, meta->skb);
+			ieee80211_tx_status(dev->wl->hw, meta->skb);
 
-			/* skb is freed by ieee80211_tx_status_irqsafe() */
+			/* skb is freed by ieee80211_tx_status() */
 			meta->skb = NULL;
 		} else {
 			/* No need to call free_descriptor_buffer here, as
diff --git a/drivers/net/wireless/b43/leds.c b/drivers/net/wireless/b43/leds.c
index c8b3170..fbe3d4f 100644
--- a/drivers/net/wireless/b43/leds.c
+++ b/drivers/net/wireless/b43/leds.c
@@ -34,57 +34,88 @@
 static void b43_led_turn_on(struct b43_wldev *dev, u8 led_index,
 			    bool activelow)
 {
-	struct b43_wl *wl = dev->wl;
-	unsigned long flags;
 	u16 ctl;
 
-	spin_lock_irqsave(&wl->leds_lock, flags);
 	ctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
 	if (activelow)
 		ctl &= ~(1 << led_index);
 	else
 		ctl |= (1 << led_index);
 	b43_write16(dev, B43_MMIO_GPIO_CONTROL, ctl);
-	spin_unlock_irqrestore(&wl->leds_lock, flags);
 }
 
 static void b43_led_turn_off(struct b43_wldev *dev, u8 led_index,
 			     bool activelow)
 {
-	struct b43_wl *wl = dev->wl;
-	unsigned long flags;
 	u16 ctl;
 
-	spin_lock_irqsave(&wl->leds_lock, flags);
 	ctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
 	if (activelow)
 		ctl |= (1 << led_index);
 	else
 		ctl &= ~(1 << led_index);
 	b43_write16(dev, B43_MMIO_GPIO_CONTROL, ctl);
-	spin_unlock_irqrestore(&wl->leds_lock, flags);
 }
 
-/* Callback from the LED subsystem. */
-static void b43_led_brightness_set(struct led_classdev *led_dev,
-				   enum led_brightness brightness)
+static void b43_led_update(struct b43_wldev *dev,
+			   struct b43_led *led)
 {
-	struct b43_led *led = container_of(led_dev, struct b43_led, led_dev);
-	struct b43_wldev *dev = led->dev;
 	bool radio_enabled;
+	bool turn_on;
 
-	if (unlikely(b43_status(dev) < B43_STAT_INITIALIZED))
+	if (!led->wl)
 		return;
 
-	/* Checking the radio-enabled status here is slightly racy,
-	 * but we want to avoid the locking overhead and we don't care
-	 * whether the LED has the wrong state for a second. */
 	radio_enabled = (dev->phy.radio_on && dev->radio_hw_enable);
 
-	if (brightness == LED_OFF || !radio_enabled)
-		b43_led_turn_off(dev, led->index, led->activelow);
+	/* The led->state read is racy, but we don't care. In case we raced
+	 * with the brightness_set handler, we will be called again soon
+	 * to fixup our state. */
+	if (radio_enabled)
+		turn_on = atomic_read(&led->state) != LED_OFF;
 	else
+		turn_on = 0;
+	if (turn_on == led->hw_state)
+		return;
+	led->hw_state = turn_on;
+
+	if (turn_on)
 		b43_led_turn_on(dev, led->index, led->activelow);
+	else
+		b43_led_turn_off(dev, led->index, led->activelow);
+}
+
+static void b43_leds_work(struct work_struct *work)
+{
+	struct b43_leds *leds = container_of(work, struct b43_leds, work);
+	struct b43_wl *wl = container_of(leds, struct b43_wl, leds);
+	struct b43_wldev *dev;
+
+	mutex_lock(&wl->mutex);
+	dev = wl->current_dev;
+	if (unlikely(!dev || b43_status(dev) < B43_STAT_STARTED))
+		goto out_unlock;
+
+	b43_led_update(dev, &wl->leds.led_tx);
+	b43_led_update(dev, &wl->leds.led_rx);
+	b43_led_update(dev, &wl->leds.led_radio);
+	b43_led_update(dev, &wl->leds.led_assoc);
+
+out_unlock:
+	mutex_unlock(&wl->mutex);
+}
+
+/* Callback from the LED subsystem. */
+static void b43_led_brightness_set(struct led_classdev *led_dev,
+				   enum led_brightness brightness)
+{
+	struct b43_led *led = container_of(led_dev, struct b43_led, led_dev);
+	struct b43_wl *wl = led->wl;
+
+	if (likely(!wl->leds.stop)) {
+		atomic_set(&led->state, brightness);
+		ieee80211_queue_work(wl->hw, &wl->leds.work);
+	}
 }
 
 static int b43_register_led(struct b43_wldev *dev, struct b43_led *led,
@@ -93,15 +124,15 @@ static int b43_register_led(struct b43_wldev *dev, struct b43_led *led,
 {
 	int err;
 
-	b43_led_turn_off(dev, led_index, activelow);
-	if (led->dev)
+	if (led->wl)
 		return -EEXIST;
 	if (!default_trigger)
 		return -EINVAL;
-	led->dev = dev;
+	led->wl = dev->wl;
 	led->index = led_index;
 	led->activelow = activelow;
 	strncpy(led->name, name, sizeof(led->name));
+	atomic_set(&led->state, 0);
 
 	led->led_dev.name = led->name;
 	led->led_dev.default_trigger = default_trigger;
@@ -110,19 +141,19 @@ static int b43_register_led(struct b43_wldev *dev, struct b43_led *led,
 	err = led_classdev_register(dev->dev->dev, &led->led_dev);
 	if (err) {
 		b43warn(dev->wl, "LEDs: Failed to register %s\n", name);
-		led->dev = NULL;
+		led->wl = NULL;
 		return err;
 	}
+
 	return 0;
 }
 
 static void b43_unregister_led(struct b43_led *led)
 {
-	if (!led->dev)
+	if (!led->wl)
 		return;
 	led_classdev_unregister(&led->led_dev);
-	b43_led_turn_off(led->dev, led->index, led->activelow);
-	led->dev = NULL;
+	led->wl = NULL;
 }
 
 static void b43_map_led(struct b43_wldev *dev,
@@ -137,24 +168,20 @@ static void b43_map_led(struct b43_wldev *dev,
 	 * generic LED triggers. */
 	switch (behaviour) {
 	case B43_LED_INACTIVE:
-		break;
 	case B43_LED_OFF:
-		b43_led_turn_off(dev, led_index, activelow);
-		break;
 	case B43_LED_ON:
-		b43_led_turn_on(dev, led_index, activelow);
 		break;
 	case B43_LED_ACTIVITY:
 	case B43_LED_TRANSFER:
 	case B43_LED_APTRANSFER:
 		snprintf(name, sizeof(name),
 			 "b43-%s::tx", wiphy_name(hw->wiphy));
-		b43_register_led(dev, &dev->led_tx, name,
+		b43_register_led(dev, &dev->wl->leds.led_tx, name,
 				 ieee80211_get_tx_led_name(hw),
 				 led_index, activelow);
 		snprintf(name, sizeof(name),
 			 "b43-%s::rx", wiphy_name(hw->wiphy));
-		b43_register_led(dev, &dev->led_rx, name,
+		b43_register_led(dev, &dev->wl->leds.led_rx, name,
 				 ieee80211_get_rx_led_name(hw),
 				 led_index, activelow);
 		break;
@@ -164,18 +191,15 @@ static void b43_map_led(struct b43_wldev *dev,
 	case B43_LED_MODE_BG:
 		snprintf(name, sizeof(name),
 			 "b43-%s::radio", wiphy_name(hw->wiphy));
-		b43_register_led(dev, &dev->led_radio, name,
+		b43_register_led(dev, &dev->wl->leds.led_radio, name,
 				 ieee80211_get_radio_led_name(hw),
 				 led_index, activelow);
-		/* Sync the RF-kill LED state with radio and switch states. */
-		if (dev->phy.radio_on && b43_is_hw_radio_enabled(dev))
-			b43_led_turn_on(dev, led_index, activelow);
 		break;
 	case B43_LED_WEIRD:
 	case B43_LED_ASSOC:
 		snprintf(name, sizeof(name),
 			 "b43-%s::assoc", wiphy_name(hw->wiphy));
-		b43_register_led(dev, &dev->led_assoc, name,
+		b43_register_led(dev, &dev->wl->leds.led_assoc, name,
 				 ieee80211_get_assoc_led_name(hw),
 				 led_index, activelow);
 		break;
@@ -186,58 +210,150 @@ static void b43_map_led(struct b43_wldev *dev,
 	}
 }
 
-void b43_leds_init(struct b43_wldev *dev)
+static void b43_led_get_sprominfo(struct b43_wldev *dev,
+				  unsigned int led_index,
+				  enum b43_led_behaviour *behaviour,
+				  bool *activelow)
 {
 	struct ssb_bus *bus = dev->dev->bus;
 	u8 sprom[4];
-	int i;
-	enum b43_led_behaviour behaviour;
-	bool activelow;
 
 	sprom[0] = bus->sprom.gpio0;
 	sprom[1] = bus->sprom.gpio1;
 	sprom[2] = bus->sprom.gpio2;
 	sprom[3] = bus->sprom.gpio3;
 
-	for (i = 0; i < 4; i++) {
-		if (sprom[i] == 0xFF) {
-			/* There is no LED information in the SPROM
-			 * for this LED. Hardcode it here. */
-			activelow = 0;
-			switch (i) {
-			case 0:
-				behaviour = B43_LED_ACTIVITY;
-				activelow = 1;
-				if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ)
-					behaviour = B43_LED_RADIO_ALL;
-				break;
-			case 1:
-				behaviour = B43_LED_RADIO_B;
-				if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK)
-					behaviour = B43_LED_ASSOC;
-				break;
-			case 2:
-				behaviour = B43_LED_RADIO_A;
-				break;
-			case 3:
-				behaviour = B43_LED_OFF;
-				break;
-			default:
-				B43_WARN_ON(1);
-				return;
-			}
+	if (sprom[led_index] == 0xFF) {
+		/* There is no LED information in the SPROM
+		 * for this LED. Hardcode it here. */
+		*activelow = 0;
+		switch (led_index) {
+		case 0:
+			*behaviour = B43_LED_ACTIVITY;
+			*activelow = 1;
+			if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ)
+				*behaviour = B43_LED_RADIO_ALL;
+			break;
+		case 1:
+			*behaviour = B43_LED_RADIO_B;
+			if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK)
+				*behaviour = B43_LED_ASSOC;
+			break;
+		case 2:
+			*behaviour = B43_LED_RADIO_A;
+			break;
+		case 3:
+			*behaviour = B43_LED_OFF;
+			break;
+		default:
+			B43_WARN_ON(1);
+			return;
+		}
+	} else {
+		*behaviour = sprom[led_index] & B43_LED_BEHAVIOUR;
+		*activelow = !!(sprom[led_index] & B43_LED_ACTIVELOW);
+	}
+}
+
+void b43_leds_init(struct b43_wldev *dev)
+{
+	struct b43_led *led;
+	unsigned int i;
+	enum b43_led_behaviour behaviour;
+	bool activelow;
+
+	/* Sync the RF-kill LED state (if we have one) with radio and switch states. */
+	led = &dev->wl->leds.led_radio;
+	if (led->wl) {
+		if (dev->phy.radio_on && b43_is_hw_radio_enabled(dev)) {
+			b43_led_turn_on(dev, led->index, led->activelow);
+			led->hw_state = 1;
+			atomic_set(&led->state, 1);
 		} else {
-			behaviour = sprom[i] & B43_LED_BEHAVIOUR;
-			activelow = !!(sprom[i] & B43_LED_ACTIVELOW);
+			b43_led_turn_off(dev, led->index, led->activelow);
+			led->hw_state = 0;
+			atomic_set(&led->state, 0);
 		}
-		b43_map_led(dev, i, behaviour, activelow);
 	}
+
+	/* Initialize TX/RX/ASSOC leds */
+	led = &dev->wl->leds.led_tx;
+	if (led->wl) {
+		b43_led_turn_off(dev, led->index, led->activelow);
+		led->hw_state = 0;
+		atomic_set(&led->state, 0);
+	}
+	led = &dev->wl->leds.led_rx;
+	if (led->wl) {
+		b43_led_turn_off(dev, led->index, led->activelow);
+		led->hw_state = 0;
+		atomic_set(&led->state, 0);
+	}
+	led = &dev->wl->leds.led_assoc;
+	if (led->wl) {
+		b43_led_turn_off(dev, led->index, led->activelow);
+		led->hw_state = 0;
+		atomic_set(&led->state, 0);
+	}
+
+	/* Initialize other LED states. */
+	for (i = 0; i < B43_MAX_NR_LEDS; i++) {
+		b43_led_get_sprominfo(dev, i, &behaviour, &activelow);
+		switch (behaviour) {
+		case B43_LED_OFF:
+			b43_led_turn_off(dev, i, activelow);
+			break;
+		case B43_LED_ON:
+			b43_led_turn_on(dev, i, activelow);
+			break;
+		default:
+			/* Leave others as-is. */
+			break;
+		}
+	}
+
+	dev->wl->leds.stop = 0;
 }
 
 void b43_leds_exit(struct b43_wldev *dev)
 {
-	b43_unregister_led(&dev->led_tx);
-	b43_unregister_led(&dev->led_rx);
-	b43_unregister_led(&dev->led_assoc);
-	b43_unregister_led(&dev->led_radio);
+	struct b43_leds *leds = &dev->wl->leds;
+
+	b43_led_turn_off(dev, leds->led_tx.index, leds->led_tx.activelow);
+	b43_led_turn_off(dev, leds->led_rx.index, leds->led_rx.activelow);
+	b43_led_turn_off(dev, leds->led_assoc.index, leds->led_assoc.activelow);
+	b43_led_turn_off(dev, leds->led_radio.index, leds->led_radio.activelow);
+}
+
+void b43_leds_stop(struct b43_wldev *dev)
+{
+	struct b43_leds *leds = &dev->wl->leds;
+
+	leds->stop = 1;
+	cancel_work_sync(&leds->work);
+}
+
+void b43_leds_register(struct b43_wldev *dev)
+{
+	unsigned int i;
+	enum b43_led_behaviour behaviour;
+	bool activelow;
+
+	INIT_WORK(&dev->wl->leds.work, b43_leds_work);
+
+	/* Register the LEDs to the LED subsystem. */
+	for (i = 0; i < B43_MAX_NR_LEDS; i++) {
+		b43_led_get_sprominfo(dev, i, &behaviour, &activelow);
+		b43_map_led(dev, i, behaviour, activelow);
+	}
+}
+
+void b43_leds_unregister(struct b43_wldev *dev)
+{
+	struct b43_leds *leds = &dev->wl->leds;
+
+	b43_unregister_led(&leds->led_tx);
+	b43_unregister_led(&leds->led_rx);
+	b43_unregister_led(&leds->led_assoc);
+	b43_unregister_led(&leds->led_radio);
 }
diff --git a/drivers/net/wireless/b43/leds.h b/drivers/net/wireless/b43/leds.h
index b8b1dd5..9592e4c 100644
--- a/drivers/net/wireless/b43/leds.h
+++ b/drivers/net/wireless/b43/leds.h
@@ -7,12 +7,13 @@ struct b43_wldev;
 
 #include <linux/types.h>
 #include <linux/leds.h>
+#include <linux/workqueue.h>
 
 
 #define B43_LED_MAX_NAME_LEN	31
 
 struct b43_led {
-	struct b43_wldev *dev;
+	struct b43_wl *wl;
 	/* The LED class device */
 	struct led_classdev led_dev;
 	/* The index number of the LED. */
@@ -22,8 +23,24 @@ struct b43_led {
 	bool activelow;
 	/* The unique name string for this LED device. */
 	char name[B43_LED_MAX_NAME_LEN + 1];
+	/* The current status of the LED. This is updated locklessly. */
+	atomic_t state;
+	/* The active state in hardware. */
+	bool hw_state;
 };
 
+struct b43_leds {
+	struct b43_led led_tx;
+	struct b43_led led_rx;
+	struct b43_led led_radio;
+	struct b43_led led_assoc;
+
+	bool stop;
+	struct work_struct work;
+};
+
+#define B43_MAX_NR_LEDS			4
+
 #define B43_LED_BEHAVIOUR		0x7F
 #define B43_LED_ACTIVELOW		0x80
 /* LED behaviour values */
@@ -42,23 +59,35 @@ enum b43_led_behaviour {
 	B43_LED_INACTIVE,
 };
 
+void b43_leds_register(struct b43_wldev *dev);
+void b43_leds_unregister(struct b43_wldev *dev);
 void b43_leds_init(struct b43_wldev *dev);
 void b43_leds_exit(struct b43_wldev *dev);
+void b43_leds_stop(struct b43_wldev *dev);
 
 
 #else /* CONFIG_B43_LEDS */
 /* LED support disabled */
 
-struct b43_led {
+struct b43_leds {
 	/* empty */
 };
 
+static inline void b43_leds_register(struct b43_wldev *dev)
+{
+}
+static inline void b43_leds_unregister(struct b43_wldev *dev)
+{
+}
 static inline void b43_leds_init(struct b43_wldev *dev)
 {
 }
 static inline void b43_leds_exit(struct b43_wldev *dev)
 {
 }
+static inline void b43_leds_stop(struct b43_wldev *dev)
+{
+}
 #endif /* CONFIG_B43_LEDS */
 
 #endif /* B43_LEDS_H_ */
diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c
index e789792..9b907a3 100644
--- a/drivers/net/wireless/b43/main.c
+++ b/drivers/net/wireless/b43/main.c
@@ -8,6 +8,9 @@
   Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org>
   Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch>
 
+  SDIO support
+  Copyright (c) 2009 Albert Herranz <albert_herranz@yahoo.es>
+
   Some parts of the code in this file are derived from the ipw2200
   driver  Copyright(c) 2003 - 2004 Intel Corporation.
 
@@ -53,6 +56,8 @@
 #include "xmit.h"
 #include "lo.h"
 #include "pcmcia.h"
+#include "sdio.h"
+#include <linux/mmc/sdio_func.h>
 
 MODULE_DESCRIPTION("Broadcom B43 wireless driver");
 MODULE_AUTHOR("Martin Langer");
@@ -1587,7 +1592,7 @@ static void b43_beacon_update_trigger_work(struct work_struct *work)
 	mutex_lock(&wl->mutex);
 	dev = wl->current_dev;
 	if (likely(dev && (b43_status(dev) >= B43_STAT_INITIALIZED))) {
-		if (0 /*FIXME dev->dev->bus->bustype == SSB_BUSTYPE_SDIO*/) {
+		if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
 			/* wl->mutex is enough. */
 			b43_do_beacon_update_trigger_work(dev);
 			mmiowb();
@@ -1825,6 +1830,16 @@ static void b43_do_interrupt_thread(struct b43_wldev *dev)
 
 	/* Re-enable interrupts on the device by restoring the current interrupt mask. */
 	b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask);
+
+#if B43_DEBUG
+	if (b43_debug(dev, B43_DBG_VERBOSESTATS)) {
+		dev->irq_count++;
+		for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) {
+			if (reason & (1 << i))
+				dev->irq_bit_count[i]++;
+		}
+	}
+#endif
 }
 
 /* Interrupt thread handler. Handles device interrupts in thread context. */
@@ -1905,6 +1920,21 @@ static irqreturn_t b43_interrupt_handler(int irq, void *dev_id)
 	return ret;
 }
 
+/* SDIO interrupt handler. This runs in process context. */
+static void b43_sdio_interrupt_handler(struct b43_wldev *dev)
+{
+	struct b43_wl *wl = dev->wl;
+	irqreturn_t ret;
+
+	mutex_lock(&wl->mutex);
+
+	ret = b43_do_interrupt(dev);
+	if (ret == IRQ_WAKE_THREAD)
+		b43_do_interrupt_thread(dev);
+
+	mutex_unlock(&wl->mutex);
+}
+
 void b43_do_release_fw(struct b43_firmware_file *fw)
 {
 	release_firmware(fw->data);
@@ -2645,6 +2675,20 @@ static void b43_adjust_opmode(struct b43_wldev *dev)
 			cfp_pretbtt = 50;
 	}
 	b43_write16(dev, 0x612, cfp_pretbtt);
+
+	/* FIXME: We don't currently implement the PMQ mechanism,
+	 *        so always disable it. If we want to implement PMQ,
+	 *        we need to enable it here (clear DISCPMQ) in AP mode.
+	 */
+	if (0  /* ctl & B43_MACCTL_AP */) {
+		b43_write32(dev, B43_MMIO_MACCTL,
+			    b43_read32(dev, B43_MMIO_MACCTL)
+			    & ~B43_MACCTL_DISCPMQ);
+	} else {
+		b43_write32(dev, B43_MMIO_MACCTL,
+			    b43_read32(dev, B43_MMIO_MACCTL)
+			    | B43_MACCTL_DISCPMQ);
+	}
 }
 
 static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm)
@@ -2873,6 +2917,27 @@ static void b43_periodic_every15sec(struct b43_wldev *dev)
 
 	atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT);
 	wmb();
+
+#if B43_DEBUG
+	if (b43_debug(dev, B43_DBG_VERBOSESTATS)) {
+		unsigned int i;
+
+		b43dbg(dev->wl, "Stats: %7u IRQs/sec, %7u TX/sec, %7u RX/sec\n",
+		       dev->irq_count / 15,
+		       dev->tx_count / 15,
+		       dev->rx_count / 15);
+		dev->irq_count = 0;
+		dev->tx_count = 0;
+		dev->rx_count = 0;
+		for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) {
+			if (dev->irq_bit_count[i]) {
+				b43dbg(dev->wl, "Stats: %7u IRQ-%02u/sec (0x%08X)\n",
+				       dev->irq_bit_count[i] / 15, i, (1 << i));
+				dev->irq_bit_count[i] = 0;
+			}
+		}
+	}
+#endif
 }
 
 static void do_periodic_work(struct b43_wldev *dev)
@@ -3002,14 +3067,18 @@ static void b43_security_init(struct b43_wldev *dev)
 static int b43_rng_read(struct hwrng *rng, u32 *data)
 {
 	struct b43_wl *wl = (struct b43_wl *)rng->priv;
+	struct b43_wldev *dev;
+	int count = -ENODEV;
 
-	/* FIXME: We need to take wl->mutex here to make sure the device
-	 * is not going away from under our ass. However it could deadlock
-	 * with hwrng internal locking. */
-
-	*data = b43_read16(wl->current_dev, B43_MMIO_RNG);
+	mutex_lock(&wl->mutex);
+	dev = wl->current_dev;
+	if (likely(dev && b43_status(dev) >= B43_STAT_INITIALIZED)) {
+		*data = b43_read16(dev, B43_MMIO_RNG);
+		count = sizeof(u16);
+	}
+	mutex_unlock(&wl->mutex);
 
-	return (sizeof(u16));
+	return count;
 }
 #endif /* CONFIG_B43_HWRNG */
 
@@ -3068,6 +3137,9 @@ static void b43_tx_work(struct work_struct *work)
 			dev_kfree_skb(skb); /* Drop it */
 	}
 
+#if B43_DEBUG
+	dev->tx_count++;
+#endif
 	mutex_unlock(&wl->mutex);
 }
 
@@ -3820,7 +3892,7 @@ redo:
 
 	/* Disable interrupts on the device. */
 	b43_set_status(dev, B43_STAT_INITIALIZED);
-	if (0 /*FIXME dev->dev->bus->bustype == SSB_BUSTYPE_SDIO*/) {
+	if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
 		/* wl->mutex is locked. That is enough. */
 		b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0);
 		b43_read32(dev, B43_MMIO_GEN_IRQ_MASK);	/* Flush */
@@ -3830,10 +3902,15 @@ redo:
 		b43_read32(dev, B43_MMIO_GEN_IRQ_MASK);	/* Flush */
 		spin_unlock_irq(&wl->hardirq_lock);
 	}
-	/* Synchronize the interrupt handlers. Unlock to avoid deadlocks. */
+	/* Synchronize and free the interrupt handlers. Unlock to avoid deadlocks. */
 	orig_dev = dev;
 	mutex_unlock(&wl->mutex);
-	synchronize_irq(dev->dev->irq);
+	if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
+		b43_sdio_free_irq(dev);
+	} else {
+		synchronize_irq(dev->dev->irq);
+		free_irq(dev->dev->irq, dev);
+	}
 	mutex_lock(&wl->mutex);
 	dev = wl->current_dev;
 	if (!dev)
@@ -3850,7 +3927,7 @@ redo:
 		dev_kfree_skb(skb_dequeue(&wl->tx_queue));
 
 	b43_mac_suspend(dev);
-	free_irq(dev->dev->irq, dev);
+	b43_leds_exit(dev);
 	b43dbg(wl, "Wireless interface stopped\n");
 
 	return dev;
@@ -3864,12 +3941,20 @@ static int b43_wireless_core_start(struct b43_wldev *dev)
 	B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED);
 
 	drain_txstatus_queue(dev);
-	err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler,
-				   b43_interrupt_thread_handler,
-				   IRQF_SHARED, KBUILD_MODNAME, dev);
-	if (err) {
-		b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq);
-		goto out;
+	if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
+		err = b43_sdio_request_irq(dev, b43_sdio_interrupt_handler);
+		if (err) {
+			b43err(dev->wl, "Cannot request SDIO IRQ\n");
+			goto out;
+		}
+	} else {
+		err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler,
+					   b43_interrupt_thread_handler,
+					   IRQF_SHARED, KBUILD_MODNAME, dev);
+		if (err) {
+			b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq);
+			goto out;
+		}
 	}
 
 	/* We are ready to run. */
@@ -3882,8 +3967,10 @@ static int b43_wireless_core_start(struct b43_wldev *dev)
 	/* Start maintainance work */
 	b43_periodic_tasks_setup(dev);
 
+	b43_leds_init(dev);
+
 	b43dbg(dev->wl, "Wireless interface started\n");
-      out:
+out:
 	return err;
 }
 
@@ -4160,10 +4247,6 @@ static void b43_wireless_core_exit(struct b43_wldev *dev)
 	macctl |= B43_MACCTL_PSM_JMP0;
 	b43_write32(dev, B43_MMIO_MACCTL, macctl);
 
-	if (!dev->suspend_in_progress) {
-		b43_leds_exit(dev);
-		b43_rng_exit(dev->wl);
-	}
 	b43_dma_free(dev);
 	b43_pio_free(dev);
 	b43_chip_exit(dev);
@@ -4180,7 +4263,6 @@ static void b43_wireless_core_exit(struct b43_wldev *dev)
 /* Initialize a wireless core */
 static int b43_wireless_core_init(struct b43_wldev *dev)
 {
-	struct b43_wl *wl = dev->wl;
 	struct ssb_bus *bus = dev->dev->bus;
 	struct ssb_sprom *sprom = &bus->sprom;
 	struct b43_phy *phy = &dev->phy;
@@ -4264,7 +4346,9 @@ static int b43_wireless_core_init(struct b43_wldev *dev)
 	/* Maximum Contention Window */
 	b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF);
 
-	if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) || B43_FORCE_PIO) {
+	if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) ||
+	    (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) ||
+	    B43_FORCE_PIO) {
 		dev->__using_pio_transfers = 1;
 		err = b43_pio_init(dev);
 	} else {
@@ -4280,15 +4364,13 @@ static int b43_wireless_core_init(struct b43_wldev *dev)
 	ssb_bus_powerup(bus, !(sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW));
 	b43_upload_card_macaddress(dev);
 	b43_security_init(dev);
-	if (!dev->suspend_in_progress)
-		b43_rng_init(wl);
+
+	ieee80211_wake_queues(dev->wl->hw);
 
 	ieee80211_wake_queues(dev->wl->hw);
 
 	b43_set_status(dev, B43_STAT_INITIALIZED);
 
-	if (!dev->suspend_in_progress)
-		b43_leds_init(dev);
 out:
 	return err;
 
@@ -4837,7 +4919,6 @@ static int b43_wireless_init(struct ssb_device *dev)
 
 	/* Initialize struct b43_wl */
 	wl->hw = hw;
-	spin_lock_init(&wl->leds_lock);
 	mutex_init(&wl->mutex);
 	spin_lock_init(&wl->hardirq_lock);
 	INIT_LIST_HEAD(&wl->devlist);
@@ -4878,6 +4959,8 @@ static int b43_probe(struct ssb_device *dev, const struct ssb_device_id *id)
 		err = ieee80211_register_hw(wl->hw);
 		if (err)
 			goto err_one_core_detach;
+		b43_leds_register(wl->current_dev);
+		b43_rng_init(wl);
 	}
 
       out:
@@ -4906,12 +4989,15 @@ static void b43_remove(struct ssb_device *dev)
 		 * might have modified it. Restoring is important, so the networking
 		 * stack can properly free resources. */
 		wl->hw->queues = wl->mac80211_initially_registered_queues;
+		b43_leds_stop(wldev);
 		ieee80211_unregister_hw(wl->hw);
 	}
 
 	b43_one_core_detach(dev);
 
 	if (list_empty(&wl->devlist)) {
+		b43_rng_exit(wl);
+		b43_leds_unregister(wldev);
 		/* Last core on the chip unregistered.
 		 * We can destroy common struct b43_wl.
 		 */
@@ -4929,80 +5015,17 @@ void b43_controller_restart(struct b43_wldev *dev, const char *reason)
 	ieee80211_queue_work(dev->wl->hw, &dev->restart_work);
 }
 
-#ifdef CONFIG_PM
-
-static int b43_suspend(struct ssb_device *dev, pm_message_t state)
-{
-	struct b43_wldev *wldev = ssb_get_drvdata(dev);
-	struct b43_wl *wl = wldev->wl;
-
-	b43dbg(wl, "Suspending...\n");
-
-	mutex_lock(&wl->mutex);
-	wldev->suspend_in_progress = true;
-	wldev->suspend_init_status = b43_status(wldev);
-	if (wldev->suspend_init_status >= B43_STAT_STARTED)
-		wldev = b43_wireless_core_stop(wldev);
-	if (wldev && wldev->suspend_init_status >= B43_STAT_INITIALIZED)
-		b43_wireless_core_exit(wldev);
-	mutex_unlock(&wl->mutex);
-
-	b43dbg(wl, "Device suspended.\n");
-
-	return 0;
-}
-
-static int b43_resume(struct ssb_device *dev)
-{
-	struct b43_wldev *wldev = ssb_get_drvdata(dev);
-	struct b43_wl *wl = wldev->wl;
-	int err = 0;
-
-	b43dbg(wl, "Resuming...\n");
-
-	mutex_lock(&wl->mutex);
-	if (wldev->suspend_init_status >= B43_STAT_INITIALIZED) {
-		err = b43_wireless_core_init(wldev);
-		if (err) {
-			b43err(wl, "Resume failed at core init\n");
-			goto out;
-		}
-	}
-	if (wldev->suspend_init_status >= B43_STAT_STARTED) {
-		err = b43_wireless_core_start(wldev);
-		if (err) {
-			b43_leds_exit(wldev);
-			b43_rng_exit(wldev->wl);
-			b43_wireless_core_exit(wldev);
-			b43err(wl, "Resume failed at core start\n");
-			goto out;
-		}
-	}
-	b43dbg(wl, "Device resumed.\n");
- out:
-	wldev->suspend_in_progress = false;
-	mutex_unlock(&wl->mutex);
-	return err;
-}
-
-#else /* CONFIG_PM */
-# define b43_suspend	NULL
-# define b43_resume	NULL
-#endif /* CONFIG_PM */
-
 static struct ssb_driver b43_ssb_driver = {
 	.name		= KBUILD_MODNAME,
 	.id_table	= b43_ssb_tbl,
 	.probe		= b43_probe,
 	.remove		= b43_remove,
-	.suspend	= b43_suspend,
-	.resume		= b43_resume,
 };
 
 static void b43_print_driverinfo(void)
 {
 	const char *feat_pci = "", *feat_pcmcia = "", *feat_nphy = "",
-		   *feat_leds = "";
+		   *feat_leds = "", *feat_sdio = "";
 
 #ifdef CONFIG_B43_PCI_AUTOSELECT
 	feat_pci = "P";
@@ -5016,11 +5039,14 @@ static void b43_print_driverinfo(void)
 #ifdef CONFIG_B43_LEDS
 	feat_leds = "L";
 #endif
+#ifdef CONFIG_B43_SDIO
+	feat_sdio = "S";
+#endif
 	printk(KERN_INFO "Broadcom 43xx driver loaded "
-	       "[ Features: %s%s%s%s, Firmware-ID: "
+	       "[ Features: %s%s%s%s%s, Firmware-ID: "
 	       B43_SUPPORTED_FIRMWARE_ID " ]\n",
 	       feat_pci, feat_pcmcia, feat_nphy,
-	       feat_leds);
+	       feat_leds, feat_sdio);
 }
 
 static int __init b43_init(void)
@@ -5031,13 +5057,18 @@ static int __init b43_init(void)
 	err = b43_pcmcia_init();
 	if (err)
 		goto err_dfs_exit;
-	err = ssb_driver_register(&b43_ssb_driver);
+	err = b43_sdio_init();
 	if (err)
 		goto err_pcmcia_exit;
+	err = ssb_driver_register(&b43_ssb_driver);
+	if (err)
+		goto err_sdio_exit;
 	b43_print_driverinfo();
 
 	return err;
 
+err_sdio_exit:
+	b43_sdio_exit();
 err_pcmcia_exit:
 	b43_pcmcia_exit();
 err_dfs_exit:
@@ -5048,6 +5079,7 @@ err_dfs_exit:
 static void __exit b43_exit(void)
 {
 	ssb_driver_unregister(&b43_ssb_driver);
+	b43_sdio_exit();
 	b43_pcmcia_exit();
 	b43_debugfs_exit();
 }
diff --git a/drivers/net/wireless/b43/phy_lp.c b/drivers/net/wireless/b43/phy_lp.c
index 3e02d96..1e318d8 100644
--- a/drivers/net/wireless/b43/phy_lp.c
+++ b/drivers/net/wireless/b43/phy_lp.c
@@ -2228,6 +2228,16 @@ static enum b43_txpwr_result b43_lpphy_op_recalc_txpower(struct b43_wldev *dev,
 	return B43_TXPWR_RES_DONE;
 }
 
+void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on)
+{
+       if (on) {
+               b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xfff8);
+       } else {
+               b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0x0007);
+               b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x0007);
+       }
+}
+
 const struct b43_phy_operations b43_phyops_lp = {
 	.allocate		= b43_lpphy_op_allocate,
 	.free			= b43_lpphy_op_free,
@@ -2239,7 +2249,7 @@ const struct b43_phy_operations b43_phyops_lp = {
 	.radio_read		= b43_lpphy_op_radio_read,
 	.radio_write		= b43_lpphy_op_radio_write,
 	.software_rfkill	= b43_lpphy_op_software_rfkill,
-	.switch_analog		= b43_phyop_switch_analog_generic,
+	.switch_analog		= b43_lpphy_op_switch_analog,
 	.switch_channel		= b43_lpphy_op_switch_channel,
 	.get_default_chan	= b43_lpphy_op_get_default_chan,
 	.set_rx_antenna		= b43_lpphy_op_set_rx_antenna,
diff --git a/drivers/net/wireless/b43/pio.c b/drivers/net/wireless/b43/pio.c
index 3498b68..e96091b 100644
--- a/drivers/net/wireless/b43/pio.c
+++ b/drivers/net/wireless/b43/pio.c
@@ -574,7 +574,7 @@ void b43_pio_handle_txstatus(struct b43_wldev *dev,
 	q->buffer_used -= total_len;
 	q->free_packet_slots += 1;
 
-	ieee80211_tx_status_irqsafe(dev->wl->hw, pack->skb);
+	ieee80211_tx_status(dev->wl->hw, pack->skb);
 	pack->skb = NULL;
 	list_add(&pack->list, &q->packets_list);
 
diff --git a/drivers/net/wireless/b43/rfkill.c b/drivers/net/wireless/b43/rfkill.c
index 31e5599..7a3218c 100644
--- a/drivers/net/wireless/b43/rfkill.c
+++ b/drivers/net/wireless/b43/rfkill.c
@@ -28,7 +28,7 @@
 /* Returns TRUE, if the radio is enabled in hardware. */
 bool b43_is_hw_radio_enabled(struct b43_wldev *dev)
 {
-	if (dev->phy.rev >= 3) {
+	if (dev->phy.rev >= 3 || dev->phy.type == B43_PHYTYPE_LP) {
 		if (!(b43_read32(dev, B43_MMIO_RADIO_HWENABLED_HI)
 		      & B43_MMIO_RADIO_HWENABLED_HI_MASK))
 			return 1;
diff --git a/drivers/net/wireless/b43/sdio.c b/drivers/net/wireless/b43/sdio.c
new file mode 100644
index 0000000..0d3ac64
--- /dev/null
+++ b/drivers/net/wireless/b43/sdio.c
@@ -0,0 +1,202 @@
+/*
+ * Broadcom B43 wireless driver
+ *
+ * SDIO over Sonics Silicon Backplane bus glue for b43.
+ *
+ * Copyright (C) 2009 Albert Herranz
+ * Copyright (C) 2009 Michael Buesch <mb@bu3sch.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/sdio_func.h>
+#include <linux/mmc/sdio_ids.h>
+#include <linux/ssb/ssb.h>
+
+#include "sdio.h"
+#include "b43.h"
+
+
+#define HNBU_CHIPID		0x01	/* vendor & device id */
+
+#define B43_SDIO_BLOCK_SIZE	64	/* rx fifo max size in bytes */
+
+
+static const struct b43_sdio_quirk {
+	u16 vendor;
+	u16 device;
+	unsigned int quirks;
+} b43_sdio_quirks[] = {
+	{ 0x14E4, 0x4318, SSB_QUIRK_SDIO_READ_AFTER_WRITE32, },
+	{ },
+};
+
+
+static unsigned int b43_sdio_get_quirks(u16 vendor, u16 device)
+{
+	const struct b43_sdio_quirk *q;
+
+	for (q = b43_sdio_quirks; q->quirks; q++) {
+		if (vendor == q->vendor && device == q->device)
+			return q->quirks;
+	}
+
+	return 0;
+}
+
+static void b43_sdio_interrupt_dispatcher(struct sdio_func *func)
+{
+	struct b43_sdio *sdio = sdio_get_drvdata(func);
+	struct b43_wldev *dev = sdio->irq_handler_opaque;
+
+	if (unlikely(b43_status(dev) < B43_STAT_STARTED))
+		return;
+
+	sdio_release_host(func);
+	sdio->irq_handler(dev);
+	sdio_claim_host(func);
+}
+
+int b43_sdio_request_irq(struct b43_wldev *dev,
+			 void (*handler)(struct b43_wldev *dev))
+{
+	struct ssb_bus *bus = dev->dev->bus;
+	struct sdio_func *func = bus->host_sdio;
+	struct b43_sdio *sdio = sdio_get_drvdata(func);
+	int err;
+
+	sdio->irq_handler_opaque = dev;
+	sdio->irq_handler = handler;
+	sdio_claim_host(func);
+	err = sdio_claim_irq(func, b43_sdio_interrupt_dispatcher);
+	sdio_release_host(func);
+
+	return err;
+}
+
+void b43_sdio_free_irq(struct b43_wldev *dev)
+{
+	struct ssb_bus *bus = dev->dev->bus;
+	struct sdio_func *func = bus->host_sdio;
+	struct b43_sdio *sdio = sdio_get_drvdata(func);
+
+	sdio_claim_host(func);
+	sdio_release_irq(func);
+	sdio_release_host(func);
+	sdio->irq_handler_opaque = NULL;
+	sdio->irq_handler = NULL;
+}
+
+static int b43_sdio_probe(struct sdio_func *func,
+			  const struct sdio_device_id *id)
+{
+	struct b43_sdio *sdio;
+	struct sdio_func_tuple *tuple;
+	u16 vendor = 0, device = 0;
+	int error;
+
+	/* Look for the card chip identifier. */
+	tuple = func->tuples;
+	while (tuple) {
+		switch (tuple->code) {
+		case 0x80:
+			switch (tuple->data[0]) {
+			case HNBU_CHIPID:
+				if (tuple->size != 5)
+					break;
+				vendor = tuple->data[1] | (tuple->data[2]<<8);
+				device = tuple->data[3] | (tuple->data[4]<<8);
+				dev_info(&func->dev, "Chip ID %04x:%04x\n",
+					 vendor, device);
+				break;
+			default:
+				break;
+			}
+			break;
+		default:
+			break;
+		}
+		tuple = tuple->next;
+	}
+	if (!vendor || !device) {
+		error = -ENODEV;
+		goto out;
+	}
+
+	sdio_claim_host(func);
+	error = sdio_set_block_size(func, B43_SDIO_BLOCK_SIZE);
+	if (error) {
+		dev_err(&func->dev, "failed to set block size to %u bytes,"
+			" error %d\n", B43_SDIO_BLOCK_SIZE, error);
+		goto err_release_host;
+	}
+	error = sdio_enable_func(func);
+	if (error) {
+		dev_err(&func->dev, "failed to enable func, error %d\n", error);
+		goto err_release_host;
+	}
+	sdio_release_host(func);
+
+	sdio = kzalloc(sizeof(*sdio), GFP_KERNEL);
+	if (!sdio) {
+		error = -ENOMEM;
+		dev_err(&func->dev, "failed to allocate ssb bus\n");
+		goto err_disable_func;
+	}
+	error = ssb_bus_sdiobus_register(&sdio->ssb, func,
+					 b43_sdio_get_quirks(vendor, device));
+	if (error) {
+		dev_err(&func->dev, "failed to register ssb sdio bus,"
+			" error %d\n", error);
+		goto err_free_ssb;
+	}
+	sdio_set_drvdata(func, sdio);
+
+	return 0;
+
+err_free_ssb:
+	kfree(sdio);
+err_disable_func:
+	sdio_disable_func(func);
+err_release_host:
+	sdio_release_host(func);
+out:
+	return error;
+}
+
+static void b43_sdio_remove(struct sdio_func *func)
+{
+	struct b43_sdio *sdio = sdio_get_drvdata(func);
+
+	ssb_bus_unregister(&sdio->ssb);
+	sdio_disable_func(func);
+	kfree(sdio);
+	sdio_set_drvdata(func, NULL);
+}
+
+static const struct sdio_device_id b43_sdio_ids[] = {
+	{ SDIO_DEVICE(0x02d0, 0x044b) }, /* Nintendo Wii WLAN daughter card */
+	{ },
+};
+
+static struct sdio_driver b43_sdio_driver = {
+	.name		= "b43-sdio",
+	.id_table	= b43_sdio_ids,
+	.probe		= b43_sdio_probe,
+	.remove		= b43_sdio_remove,
+};
+
+int b43_sdio_init(void)
+{
+	return sdio_register_driver(&b43_sdio_driver);
+}
+
+void b43_sdio_exit(void)
+{
+	sdio_unregister_driver(&b43_sdio_driver);
+}
diff --git a/drivers/net/wireless/b43/sdio.h b/drivers/net/wireless/b43/sdio.h
new file mode 100644
index 0000000..fb63309
--- /dev/null
+++ b/drivers/net/wireless/b43/sdio.h
@@ -0,0 +1,45 @@
+#ifndef B43_SDIO_H_
+#define B43_SDIO_H_
+
+#include <linux/ssb/ssb.h>
+
+struct b43_wldev;
+
+
+#ifdef CONFIG_B43_SDIO
+
+struct b43_sdio {
+	struct ssb_bus ssb;
+	void *irq_handler_opaque;
+	void (*irq_handler)(struct b43_wldev *dev);
+};
+
+int b43_sdio_request_irq(struct b43_wldev *dev,
+			 void (*handler)(struct b43_wldev *dev));
+void b43_sdio_free_irq(struct b43_wldev *dev);
+
+int b43_sdio_init(void);
+void b43_sdio_exit(void);
+
+
+#else /* CONFIG_B43_SDIO */
+
+
+int b43_sdio_request_irq(struct b43_wldev *dev,
+			 void (*handler)(struct b43_wldev *dev))
+{
+	return -ENODEV;
+}
+void b43_sdio_free_irq(struct b43_wldev *dev)
+{
+}
+static inline int b43_sdio_init(void)
+{
+	return 0;
+}
+static inline void b43_sdio_exit(void)
+{
+}
+
+#endif /* CONFIG_B43_SDIO */
+#endif /* B43_SDIO_H_ */
diff --git a/drivers/net/wireless/b43/xmit.c b/drivers/net/wireless/b43/xmit.c
index 14f5412..ac9f600 100644
--- a/drivers/net/wireless/b43/xmit.c
+++ b/drivers/net/wireless/b43/xmit.c
@@ -690,8 +690,11 @@ void b43_rx(struct b43_wldev *dev, struct sk_buff *skb, const void *_rxhdr)
 	}
 
 	memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status));
-	ieee80211_rx_irqsafe(dev->wl->hw, skb);
+	ieee80211_rx(dev->wl->hw, skb);
 
+#if B43_DEBUG
+	dev->rx_count++;
+#endif
 	return;
 drop:
 	b43dbg(dev->wl, "RX: Packet dropped\n");
diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c
index ca61d37..3259b88 100644
--- a/drivers/net/wireless/iwlwifi/iwl-4965.c
+++ b/drivers/net/wireless/iwlwifi/iwl-4965.c
@@ -2021,6 +2021,12 @@ static int iwl4965_tx_status_reply_tx(struct iwl_priv *priv,
 					   agg->frame_count, txq_id, idx);
 
 			hdr = iwl_tx_queue_get_hdr(priv, txq_id, idx);
+			if (!hdr) {
+				IWL_ERR(priv,
+					"BUG_ON idx doesn't point to valid skb"
+					" idx=%d, txq_id=%d\n", idx, txq_id);
+				return -1;
+			}
 
 			sc = le16_to_cpu(hdr->seq_ctrl);
 			if (idx != (SEQ_TO_SN(sc) & 0xff)) {
diff --git a/drivers/net/wireless/iwlwifi/iwl-5000.c b/drivers/net/wireless/iwlwifi/iwl-5000.c
index 1d539e3..a6391c7 100644
--- a/drivers/net/wireless/iwlwifi/iwl-5000.c
+++ b/drivers/net/wireless/iwlwifi/iwl-5000.c
@@ -1163,6 +1163,12 @@ static int iwl5000_tx_status_reply_tx(struct iwl_priv *priv,
 					   agg->frame_count, txq_id, idx);
 
 			hdr = iwl_tx_queue_get_hdr(priv, txq_id, idx);
+			if (!hdr) {
+				IWL_ERR(priv,
+					"BUG_ON idx doesn't point to valid skb"
+					" idx=%d, txq_id=%d\n", idx, txq_id);
+				return -1;
+			}
 
 			sc = le16_to_cpu(hdr->seq_ctrl);
 			if (idx != (SEQ_TO_SN(sc) & 0xff)) {
diff --git a/drivers/net/wireless/iwlwifi/iwl-rx.c b/drivers/net/wireless/iwlwifi/iwl-rx.c
index b90adcb..8e1bb53 100644
--- a/drivers/net/wireless/iwlwifi/iwl-rx.c
+++ b/drivers/net/wireless/iwlwifi/iwl-rx.c
@@ -250,12 +250,20 @@ void iwl_rx_allocate(struct iwl_priv *priv, gfp_t priority)
 		}
 		spin_unlock_irqrestore(&rxq->lock, flags);
 
+		if (rxq->free_count > RX_LOW_WATERMARK)
+			priority |= __GFP_NOWARN;
 		/* Alloc a new receive buffer */
 		skb = alloc_skb(priv->hw_params.rx_buf_size + 256,
 						priority);
 
 		if (!skb) {
-			IWL_CRIT(priv, "Can not allocate SKB buffers\n");
+			if (net_ratelimit())
+				IWL_DEBUG_INFO(priv, "Failed to allocate SKB buffer.\n");
+			if ((rxq->free_count <= RX_LOW_WATERMARK) &&
+			    net_ratelimit())
+				IWL_CRIT(priv, "Failed to allocate SKB buffer with %s. Only %u free buffers remaining.\n",
+					 priority == GFP_ATOMIC ?  "GFP_ATOMIC" : "GFP_KERNEL",
+					 rxq->free_count);
 			/* We don't reschedule replenish work here -- we will
 			 * call the restock method and if it still needs
 			 * more buffers it will schedule replenish */
diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c
index a2b9ec8..c6633fe 100644
--- a/drivers/net/wireless/iwlwifi/iwl-sta.c
+++ b/drivers/net/wireless/iwlwifi/iwl-sta.c
@@ -520,7 +520,7 @@ int iwl_send_static_wepkey_cmd(struct iwl_priv *priv, u8 send_if_empty)
 	struct iwl_host_cmd cmd = {
 		.id = REPLY_WEPKEY,
 		.data = wep_cmd,
-		.flags = CMD_SYNC,
+		.flags = CMD_ASYNC,
 	};
 
 	memset(wep_cmd, 0, cmd_size +
diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c
index 0909668..4f2d439 100644
--- a/drivers/net/wireless/iwlwifi/iwl3945-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c
@@ -1146,11 +1146,18 @@ static void iwl3945_rx_allocate(struct iwl_priv *priv, gfp_t priority)
 		}
 		spin_unlock_irqrestore(&rxq->lock, flags);
 
+		if (rxq->free_count > RX_LOW_WATERMARK)
+			priority |= __GFP_NOWARN;
 		/* Alloc a new receive buffer */
 		skb = alloc_skb(priv->hw_params.rx_buf_size, priority);
 		if (!skb) {
 			if (net_ratelimit())
-				IWL_CRIT(priv, ": Can not allocate SKB buffers\n");
+				IWL_DEBUG_INFO(priv, "Failed to allocate SKB buffer.\n");
+			if ((rxq->free_count <= RX_LOW_WATERMARK) &&
+			    net_ratelimit())
+				IWL_CRIT(priv, "Failed to allocate SKB buffer with %s. Only %u free buffers remaining.\n",
+					 priority == GFP_ATOMIC ?  "GFP_ATOMIC" : "GFP_KERNEL",
+					 rxq->free_count);
 			/* We don't reschedule replenish work here -- we will
 			 * call the restock method and if it still needs
 			 * more buffers it will schedule replenish */
diff --git a/drivers/net/wireless/rt2x00/rt2x00lib.h b/drivers/net/wireless/rt2x00/rt2x00lib.h
index 5462cb5..567f029 100644
--- a/drivers/net/wireless/rt2x00/rt2x00lib.h
+++ b/drivers/net/wireless/rt2x00/rt2x00lib.h
@@ -380,7 +380,7 @@ static inline void rt2x00crypto_tx_insert_iv(struct sk_buff *skb,
 {
 }
 
-static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, bool l2pad,
+static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb,
 					     unsigned int header_length,
 					     struct rxdone_entry_desc *rxdesc)
 {
diff --git a/drivers/net/wireless/wl12xx/Kconfig b/drivers/net/wireless/wl12xx/Kconfig
index 7b14d5b..88060e1 100644
--- a/drivers/net/wireless/wl12xx/Kconfig
+++ b/drivers/net/wireless/wl12xx/Kconfig
@@ -1,5 +1,5 @@
 menuconfig WL12XX
-	boolean "TI wl12xx driver support"
+	tristate "TI wl12xx driver support"
 	depends on MAC80211 && WLAN_80211 && EXPERIMENTAL
 	---help---
 	  This will enable TI wl12xx driver support. The drivers make
diff --git a/drivers/net/wireless/zd1211rw/zd_usb.c b/drivers/net/wireless/zd1211rw/zd_usb.c
index 3868884..23a6a6d 100644
--- a/drivers/net/wireless/zd1211rw/zd_usb.c
+++ b/drivers/net/wireless/zd1211rw/zd_usb.c
@@ -1070,7 +1070,7 @@ static int eject_installer(struct usb_interface *intf)
 
 	/* Find bulk out endpoint */
 	endpoint = &iface_desc->endpoint[1].desc;
-	if ((endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT &&
+	if (usb_endpoint_dir_out(endpoint) &&
 	    usb_endpoint_xfer_bulk(endpoint)) {
 		bulk_out_ep = endpoint->bEndpointAddress;
 	} else {
diff --git a/drivers/net/xilinx_emaclite.c b/drivers/net/xilinx_emaclite.c
index dc22782..83a044d 100644
--- a/drivers/net/xilinx_emaclite.c
+++ b/drivers/net/xilinx_emaclite.c
@@ -134,18 +134,15 @@ static void xemaclite_enable_interrupts(struct net_local *drvdata)
 	}
 
 	/* Enable the Rx interrupts for the first buffer */
-	reg_data = in_be32(drvdata->base_addr + XEL_RSR_OFFSET);
 	out_be32(drvdata->base_addr + XEL_RSR_OFFSET,
-		 reg_data | XEL_RSR_RECV_IE_MASK);
+		 XEL_RSR_RECV_IE_MASK);
 
 	/* Enable the Rx interrupts for the second Buffer if
 	 * configured in HW */
 	if (drvdata->rx_ping_pong != 0) {
-		reg_data = in_be32(drvdata->base_addr + XEL_BUFFER_OFFSET +
-				   XEL_RSR_OFFSET);
 		out_be32(drvdata->base_addr + XEL_BUFFER_OFFSET +
 			 XEL_RSR_OFFSET,
-			 reg_data | XEL_RSR_RECV_IE_MASK);
+			 XEL_RSR_RECV_IE_MASK);
 	}
 
 	/* Enable the Global Interrupt Enable */