diff options
| -rw-r--r-- | drivers/usb/gadget/Kconfig | 21 | ||||
| -rw-r--r-- | drivers/usb/gadget/Makefile | 1 | ||||
| -rw-r--r-- | drivers/usb/gadget/fsl_usb2_udc.c | 2500 | ||||
| -rw-r--r-- | drivers/usb/gadget/fsl_usb2_udc.h | 579 |
4 files changed, 3101 insertions, 0 deletions
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index e081f3e..8065f2b 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -68,6 +68,27 @@ choice Many controller drivers are platform-specific; these often need board-specific hooks. +config USB_GADGET_FSL_USB2 + boolean "Freescale Highspeed USB DR Peripheral Controller" + depends on MPC834x || PPC_MPC831x + select USB_GADGET_DUALSPEED + help + Some of Freescale PowerPC processors have a High Speed + Dual-Role(DR) USB controller, which supports device mode. + + The number of programmable endpoints is different through + SOC revisions. + + Say "y" to link the driver statically, or "m" to build a + dynamically linked module called "fsl_usb2_udc" and force + all gadget drivers to also be dynamically linked. + +config USB_FSL_USB2 + tristate + depends on USB_GADGET_FSL_USB2 + default USB_GADGET + select USB_GADGET_SELECTED + config USB_GADGET_NET2280 boolean "NetChip 228x" depends on PCI diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile index e71e086..5db1939 100644 --- a/drivers/usb/gadget/Makefile +++ b/drivers/usb/gadget/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_USB_GOKU) += goku_udc.o obj-$(CONFIG_USB_OMAP) += omap_udc.o obj-$(CONFIG_USB_LH7A40X) += lh7a40x_udc.o obj-$(CONFIG_USB_AT91) += at91_udc.o +obj-$(CONFIG_USB_FSL_USB2) += fsl_usb2_udc.o # # USB gadget drivers diff --git a/drivers/usb/gadget/fsl_usb2_udc.c b/drivers/usb/gadget/fsl_usb2_udc.c new file mode 100644 index 0000000..157054e --- /dev/null +++ b/drivers/usb/gadget/fsl_usb2_udc.c @@ -0,0 +1,2500 @@ +/* + * Copyright (C) 2004-2007 Freescale Semicondutor, Inc. All rights reserved. + * + * Author: Li Yang <leoli@freescale.com> + * Jiang Bo <tanya.jiang@freescale.com> + * + * Description: + * Freescale high-speed USB SOC DR module device controller driver. + * This can be found on MPC8349E/MPC8313E cpus. + * The driver is previously named as mpc_udc. Based on bare board + * code from Dave Liu and Shlomi Gridish. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#undef VERBOSE + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/ioport.h> +#include <linux/types.h> +#include <linux/errno.h> +#include <linux/delay.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/timer.h> +#include <linux/list.h> +#include <linux/interrupt.h> +#include <linux/proc_fs.h> +#include <linux/mm.h> +#include <linux/moduleparam.h> +#include <linux/device.h> +#include <linux/usb/ch9.h> +#include <linux/usb_gadget.h> +#include <linux/usb/otg.h> +#include <linux/dma-mapping.h> +#include <linux/platform_device.h> +#include <linux/fsl_devices.h> +#include <linux/dmapool.h> + +#include <asm/byteorder.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/system.h> +#include <asm/unaligned.h> +#include <asm/dma.h> +#include <asm/cacheflush.h> + +#include "fsl_usb2_udc.h" + +#define DRIVER_DESC "Freescale High-Speed USB SOC Device Controller driver" +#define DRIVER_AUTHOR "Li Yang/Jiang Bo" +#define DRIVER_VERSION "Apr 20, 2007" + +#define DMA_ADDR_INVALID (~(dma_addr_t)0) + +static const char driver_name[] = "fsl-usb2-udc"; +static const char driver_desc[] = DRIVER_DESC; + +volatile static struct usb_dr_device *dr_regs = NULL; +volatile static struct usb_sys_interface *usb_sys_regs = NULL; + +/* it is initialized in probe() */ +static struct fsl_udc *udc_controller = NULL; + +static const struct usb_endpoint_descriptor +fsl_ep0_desc = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + .bEndpointAddress = 0, + .bmAttributes = USB_ENDPOINT_XFER_CONTROL, + .wMaxPacketSize = USB_MAX_CTRL_PAYLOAD, +}; + +static int fsl_udc_suspend(struct platform_device *pdev, pm_message_t state); +static int fsl_udc_resume(struct platform_device *pdev); +static void fsl_ep_fifo_flush(struct usb_ep *_ep); + +#ifdef CONFIG_PPC32 +#define fsl_readl(addr) in_le32(addr) +#define fsl_writel(addr, val32) out_le32(val32, addr) +#else +#define fsl_readl(addr) readl(addr) +#define fsl_writel(addr, val32) writel(addr, val32) +#endif + +/******************************************************************** + * Internal Used Function +********************************************************************/ +/*----------------------------------------------------------------- + * done() - retire a request; caller blocked irqs + * @status : request status to be set, only works when + * request is still in progress. + *--------------------------------------------------------------*/ +static void done(struct fsl_ep *ep, struct fsl_req *req, int status) +{ + struct fsl_udc *udc = NULL; + unsigned char stopped = ep->stopped; + struct ep_td_struct *curr_td, *next_td; + int j; + + udc = (struct fsl_udc *)ep->udc; + /* Removed the req from fsl_ep->queue */ + list_del_init(&req->queue); + + /* req.status should be set as -EINPROGRESS in ep_queue() */ + if (req->req.status == -EINPROGRESS) + req->req.status = status; + else + status = req->req.status; + + /* Free dtd for the request */ + next_td = req->head; + for (j = 0; j < req->dtd_count; j++) { + curr_td = next_td; + if (j != req->dtd_count - 1) { + next_td = curr_td->next_td_virt; + } + dma_pool_free(udc->td_pool, curr_td, curr_td->td_dma); + } + + if (req->mapped) { + dma_unmap_single(ep->udc->gadget.dev.parent, + req->req.dma, req->req.length, + ep_is_in(ep) + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + req->req.dma = DMA_ADDR_INVALID; + req->mapped = 0; + } else + dma_sync_single_for_cpu(ep->udc->gadget.dev.parent, + req->req.dma, req->req.length, + ep_is_in(ep) + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + + if (status && (status != -ESHUTDOWN)) + VDBG("complete %s req %p stat %d len %u/%u", + ep->ep.name, &req->req, status, + req->req.actual, req->req.length); + + ep->stopped = 1; + + spin_unlock(&ep->udc->lock); + /* complete() is from gadget layer, + * eg fsg->bulk_in_complete() */ + if (req->req.complete) + req->req.complete(&ep->ep, &req->req); + + spin_lock(&ep->udc->lock); + ep->stopped = stopped; +} + +/*----------------------------------------------------------------- + * nuke(): delete all requests related to this ep + * called with spinlock held + *--------------------------------------------------------------*/ +static void nuke(struct fsl_ep *ep, int status) +{ + ep->stopped = 1; + + /* Flush fifo */ + fsl_ep_fifo_flush(&ep->ep); + + /* Whether this eq has request linked */ + while (!list_empty(&ep->queue)) { + struct fsl_req *req = NULL; + + req = list_entry(ep->queue.next, struct fsl_req, queue); + done(ep, req, status); + } +} + +/*------------------------------------------------------------------ + Internal Hardware related function + ------------------------------------------------------------------*/ + +static int dr_controller_setup(struct fsl_udc *udc) +{ + unsigned int tmp = 0, portctrl = 0, ctrl = 0; + unsigned long timeout; +#define FSL_UDC_RESET_TIMEOUT 1000 + + /* before here, make sure dr_regs has been initialized */ + if (!udc) + return -EINVAL; + + /* Stop and reset the usb controller */ + tmp = fsl_readl(&dr_regs->usbcmd); + tmp &= ~USB_CMD_RUN_STOP; + fsl_writel(tmp, &dr_regs->usbcmd); + + tmp = fsl_readl(&dr_regs->usbcmd); + tmp |= USB_CMD_CTRL_RESET; + fsl_writel(tmp, &dr_regs->usbcmd); + + /* Wait for reset to complete */ + timeout = jiffies + FSL_UDC_RESET_TIMEOUT; + while (fsl_readl(&dr_regs->usbcmd) & USB_CMD_CTRL_RESET) { + if (time_after(jiffies, timeout)) { + ERR("udc reset timeout! \n"); + return -ETIMEDOUT; + } + cpu_relax(); + } + + /* Set the controller as device mode */ + tmp = fsl_readl(&dr_regs->usbmode); + tmp |= USB_MODE_CTRL_MODE_DEVICE; + /* Disable Setup Lockout */ + tmp |= USB_MODE_SETUP_LOCK_OFF; + fsl_writel(tmp, &dr_regs->usbmode); + + /* Clear the setup status */ + fsl_writel(0, &dr_regs->usbsts); + + tmp = udc->ep_qh_dma; + tmp &= USB_EP_LIST_ADDRESS_MASK; + fsl_writel(tmp, &dr_regs->endpointlistaddr); + + VDBG("vir[qh_base] is %p phy[qh_base] is 0x%8x reg is 0x%8x", + (int)udc->ep_qh, (int)tmp, + fsl_readl(&dr_regs->endpointlistaddr)); + + /* Config PHY interface */ + portctrl = fsl_readl(&dr_regs->portsc1); + portctrl &= ~PORTSCX_PHY_TYPE_SEL; + switch (udc->phy_mode) { + case FSL_USB2_PHY_ULPI: + portctrl |= PORTSCX_PTS_ULPI; + break; + case FSL_USB2_PHY_UTMI: + case FSL_USB2_PHY_UTMI_WIDE: + portctrl |= PORTSCX_PTS_UTMI; + break; + case FSL_USB2_PHY_SERIAL: + portctrl |= PORTSCX_PTS_FSLS; + break; + default: + return -EINVAL; + } + fsl_writel(portctrl, &dr_regs->portsc1); + + /* Config control enable i/o output, cpu endian register */ + ctrl = __raw_readl(&usb_sys_regs->control); + ctrl |= USB_CTRL_IOENB; + __raw_writel(ctrl, &usb_sys_regs->control); + +#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) + /* Turn on cache snooping hardware, since some PowerPC platforms + * wholly rely on hardware to deal with cache coherent. */ + + /* Setup Snooping for all the 4GB space */ + tmp = SNOOP_SIZE_2GB; /* starts from 0x0, size 2G */ + __raw_writel(tmp, &usb_sys_regs->snoop1); + tmp |= 0x80000000; /* starts from 0x8000000, size 2G */ + __raw_writel(tmp, &usb_sys_regs->snoop2); +#endif + + return 0; +} + +/* Enable DR irq and set controller to run state */ +static void dr_controller_run(struct fsl_udc *udc) +{ + u32 temp; + + /* Enable DR irq reg */ + temp = USB_INTR_INT_EN | USB_INTR_ERR_INT_EN + | USB_INTR_PTC_DETECT_EN | USB_INTR_RESET_EN + | USB_INTR_DEVICE_SUSPEND | USB_INTR_SYS_ERR_EN; + + fsl_writel(temp, &dr_regs->usbintr); + + /* Clear stopped bit */ + udc->stopped = 0; + + /* Set the controller as device mode */ + temp = fsl_readl(&dr_regs->usbmode); + temp |= USB_MODE_CTRL_MODE_DEVICE; + fsl_writel(temp, &dr_regs->usbmode); + + /* Set controller to Run */ + temp = fsl_readl(&dr_regs->usbcmd); + temp |= USB_CMD_RUN_STOP; + fsl_writel(temp, &dr_regs->usbcmd); + + return; +} + +static void dr_controller_stop(struct fsl_udc *udc) +{ + unsigned int tmp; + + /* disable all INTR */ + fsl_writel(0, &dr_regs->usbintr); + + /* Set stopped bit for isr */ + udc->stopped = 1; + + /* disable IO output */ +/* usb_sys_regs->control = 0; */ + + /* set controller to Stop */ + tmp = fsl_readl(&dr_regs->usbcmd); + tmp &= ~USB_CMD_RUN_STOP; + fsl_writel(tmp, &dr_regs->usbcmd); + + return; +} + +void dr_ep_setup(unsigned char ep_num, unsigned char dir, unsigned char ep_type) +{ + unsigned int tmp_epctrl = 0; + + tmp_epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); + if (dir) { + if (ep_num) + tmp_epctrl |= EPCTRL_TX_DATA_TOGGLE_RST; + tmp_epctrl |= EPCTRL_TX_ENABLE; + tmp_epctrl |= ((unsigned int)(ep_type) + << EPCTRL_TX_EP_TYPE_SHIFT); + } else { + if (ep_num) + tmp_epctrl |= EPCTRL_RX_DATA_TOGGLE_RST; + tmp_epctrl |= EPCTRL_RX_ENABLE; + tmp_epctrl |= ((unsigned int)(ep_type) + << EPCTRL_RX_EP_TYPE_SHIFT); + } + + fsl_writel(tmp_epctrl, &dr_regs->endptctrl[ep_num]); +} + +static void +dr_ep_change_stall(unsigned char ep_num, unsigned char dir, int value) +{ + u32 tmp_epctrl = 0; + + tmp_epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); + + if (value) { + /* set the stall bit */ + if (dir) + tmp_epctrl |= EPCTRL_TX_EP_STALL; + else + tmp_epctrl |= EPCTRL_RX_EP_STALL; + } else { + /* clear the stall bit and reset data toggle */ + if (dir) { + tmp_epctrl &= ~EPCTRL_TX_EP_STALL; + tmp_epctrl |= EPCTRL_TX_DATA_TOGGLE_RST; + } else { + tmp_epctrl &= ~EPCTRL_RX_EP_STALL; + tmp_epctrl |= EPCTRL_RX_DATA_TOGGLE_RST; + } + } + fsl_writel(tmp_epctrl, &dr_regs->endptctrl[ep_num]); +} + +/* Get stall status of a specific ep + Return: 0: not stalled; 1:stalled */ +static int dr_ep_get_stall(unsigned char ep_num, unsigned char dir) +{ + u32 epctrl; + + epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); + if (dir) + return (epctrl & EPCTRL_TX_EP_STALL) ? 1 : 0; + else + return (epctrl & EPCTRL_RX_EP_STALL) ? 1 : 0; +} + +/******************************************************************** + Internal Structure Build up functions +********************************************************************/ + +/*------------------------------------------------------------------ +* struct_ep_qh_setup(): set the Endpoint Capabilites field of QH + * @zlt: Zero Length Termination Select (1: disable; 0: enable) + * @mult: Mult field + ------------------------------------------------------------------*/ +static void struct_ep_qh_setup(struct fsl_udc *udc, unsigned char ep_num, + unsigned char dir, unsigned char ep_type, + unsigned int max_pkt_len, + unsigned int zlt, unsigned char mult) +{ + struct ep_queue_head *p_QH = &udc->ep_qh[2 * ep_num + dir]; + unsigned int tmp = 0; + + /* set the Endpoint Capabilites in QH */ + switch (ep_type) { + case USB_ENDPOINT_XFER_CONTROL: + /* Interrupt On Setup (IOS). for control ep */ + tmp = (max_pkt_len << EP_QUEUE_HEAD_MAX_PKT_LEN_POS) + | EP_QUEUE_HEAD_IOS; + break; + case USB_ENDPOINT_XFER_ISOC: + tmp = (max_pkt_len << EP_QUEUE_HEAD_MAX_PKT_LEN_POS) + | (mult << EP_QUEUE_HEAD_MULT_POS); + break; + case USB_ENDPOINT_XFER_BULK: + case USB_ENDPOINT_XFER_INT: + tmp = max_pkt_len << EP_QUEUE_HEAD_MAX_PKT_LEN_POS; + break; + default: + VDBG("error ep type is %d", ep_type); + return; + } + if (zlt) + tmp |= EP_QUEUE_HEAD_ZLT_SEL; + p_QH->max_pkt_length = cpu_to_le32(tmp); + + return; +} + +/* Setup qh structure and ep register for ep0. */ +static void ep0_setup(struct fsl_udc *udc) +{ + /* the intialization of an ep includes: fields in QH, Regs, + * fsl_ep struct */ + struct_ep_qh_setup(udc, 0, USB_RECV, USB_ENDPOINT_XFER_CONTROL, + USB_MAX_CTRL_PAYLOAD, 0, 0); + struct_ep_qh_setup(udc, 0, USB_SEND, USB_ENDPOINT_XFER_CONTROL, + USB_MAX_CTRL_PAYLOAD, 0, 0); + dr_ep_setup(0, USB_RECV, USB_ENDPOINT_XFER_CONTROL); + dr_ep_setup(0, USB_SEND, USB_ENDPOINT_XFER_CONTROL); + + return; + +} + +/*********************************************************************** + Endpoint Management Functions +***********************************************************************/ + +/*------------------------------------------------------------------------- + * when configurations are set, or when interface settings change + * for example the do_set_interface() in gadget layer, + * the driver will enable or disable the relevant endpoints + * ep0 doesn't use this routine. It is always enabled. +-------------------------------------------------------------------------*/ +static int fsl_ep_enable(struct usb_ep *_ep, + const struct usb_endpoint_descriptor *desc) +{ + struct fsl_udc *udc = NULL; + struct fsl_ep *ep = NULL; + unsigned short max = 0; + unsigned char mult = 0, zlt; + int retval = -EINVAL; + unsigned long flags = 0; + + ep = container_of(_ep, struct fsl_ep, ep); + + /* catch various bogus parameters */ + if (!_ep || !desc || ep->desc + || (desc->bDescriptorType != USB_DT_ENDPOINT)) + return -EINVAL; + + udc = ep->udc; + + if (!udc->driver || (udc->gadget.speed == USB_SPEED_UNKNOWN)) + return -ESHUTDOWN; + + max = le16_to_cpu(desc->wMaxPacketSize); + + /* Disable automatic zlp generation. Driver is reponsible to indicate + * explicitly through req->req.zero. This is needed to enable multi-td + * request. */ + zlt = 1; + + /* Assume the max packet size from gadget is always correct */ + switch (desc->bmAttributes & 0x03) { + case USB_ENDPOINT_XFER_CONTROL: + case USB_ENDPOINT_XFER_BULK: + case USB_ENDPOINT_XFER_INT: + /* mult = 0. Execute N Transactions as demonstrated by + * the USB variable length packet protocol where N is + * computed using the Maximum Packet Length (dQH) and + * the Total Bytes field (dTD) */ + mult = 0; + break; + case USB_ENDPOINT_XFER_ISOC: + /* Calculate transactions needed for high bandwidth iso */ + mult = (unsigned char)(1 + ((max >> 11) & 0x03)); + max = max & 0x8ff; /* bit 0~10 */ + /* 3 transactions at most */ + if (mult > 3) + goto en_done; + break; + default: + goto en_done; + } + + spin_lock_irqsave(&udc->lock, flags); + ep->ep.maxpacket = max; + ep->desc = desc; + ep->stopped = 0; + + /* Controller related setup */ + /* Init EPx Queue Head (Ep Capabilites field in QH + * according to max, zlt, mult) */ + struct_ep_qh_setup(udc, (unsigned char) ep_index(ep), + (unsigned char) ((desc->bEndpointAddress & USB_DIR_IN) + ? USB_SEND : USB_RECV), + (unsigned char) (desc->bmAttributes + & USB_ENDPOINT_XFERTYPE_MASK), + max, zlt, mult); + + /* Init endpoint ctrl register */ + dr_ep_setup((unsigned char) ep_index(ep), + (unsigned char) ((desc->bEndpointAddress & USB_DIR_IN) + ? USB_SEND : USB_RECV), + (unsigned char) (desc->bmAttributes + & USB_ENDPOINT_XFERTYPE_MASK)); + + spin_unlock_irqrestore(&udc->lock, flags); + retval = 0; + + VDBG("enabled %s (ep%d%s) maxpacket %d",ep->ep.name, + ep->desc->bEndpointAddress & 0x0f, + (desc->bEndpointAddress & USB_DIR_IN) + ? "in" : "out", max); +en_done: + return retval; +} + +/*--------------------------------------------------------------------- + * @ep : the ep being unconfigured. May not be ep0 + * Any pending and uncomplete req will complete with status (-ESHUTDOWN) +*---------------------------------------------------------------------*/ +static int fsl_ep_disable(struct usb_ep *_ep) +{ + struct fsl_udc *udc = NULL; + struct fsl_ep *ep = NULL; + unsigned long flags = 0; + u32 epctrl; + int ep_num; + + ep = container_of(_ep, struct fsl_ep, ep); + if (!_ep || !ep->desc) { + VDBG("%s not enabled", _ep ? ep->ep.name : NULL); + return -EINVAL; + } + + /* disable ep on controller */ + ep_num = ep_index(ep); + epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); + if (ep_is_in(ep)) + epctrl &= ~EPCTRL_TX_ENABLE; + else + epctrl &= ~EPCTRL_RX_ENABLE; + fsl_writel(epctrl, &dr_regs->endptctrl[ep_num]); + + udc = (struct fsl_udc *)ep->udc; + spin_lock_irqsave(&udc->lock, flags); + + /* nuke all pending requests (does flush) */ + nuke(ep, -ESHUTDOWN); + + ep->desc = 0; + ep->stopped = 1; + spin_unlock_irqrestore(&udc->lock, flags); + + VDBG("disabled %s OK", _ep->name); + return 0; +} + +/*--------------------------------------------------------------------- + * allocate a request object used by this endpoint + * the main operation is to insert the req->queue to the eq->queue + * Returns the request, or null if one could not be allocated +*---------------------------------------------------------------------*/ +static struct usb_request * +fsl_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags) +{ + struct fsl_req *req = NULL; + + req = kzalloc(sizeof *req, gfp_flags); + if (!req) + return NULL; + + req->req.dma = DMA_ADDR_INVALID; + INIT_LIST_HEAD(&req->queue); + + return &req->req; +} + +static void fsl_free_request(struct usb_ep *_ep, struct usb_request *_req) +{ + struct fsl_req *req = NULL; + + req = container_of(_req, struct fsl_req, req); + + if (_req) + kfree(req); +} + +/*------------------------------------------------------------------ + * Allocate an I/O buffer +*---------------------------------------------------------------------*/ +static void *fsl_alloc_buffer(struct usb_ep *_ep, unsigned bytes, + dma_addr_t *dma, gfp_t gfp_flags) +{ + struct fsl_ep *ep; + + if (!_ep) + return NULL; + + ep = container_of(_ep, struct fsl_ep, ep); + + return dma_alloc_coherent(ep->udc->gadget.dev.parent, + bytes, dma, gfp_flags); +} + +/*------------------------------------------------------------------ + * frees an i/o buffer +*---------------------------------------------------------------------*/ +static void fsl_free_buffer(struct usb_ep *_ep, void *buf, + dma_addr_t dma, unsigned bytes) +{ + struct fsl_ep *ep; + + if (!_ep) + return NULL; + + ep = container_of(_ep, struct fsl_ep, ep); + + dma_free_coherent(ep->udc->gadget.dev.parent, bytes, buf, dma); +} + +/*-------------------------------------------------------------------------*/ +static int fsl_queue_td(struct fsl_ep *ep, struct fsl_req *req) +{ + int i = ep_index(ep) * 2 + ep_is_in(ep); + u32 temp, bitmask, tmp_stat; + struct ep_queue_head *dQH = &ep->udc->ep_qh[i]; + + /* VDBG("QH addr Register 0x%8x", dr_regs->endpointlistaddr); + VDBG("ep_qh[%d] addr is 0x%8x", i, (u32)&(ep->udc->ep_qh[i])); */ + + bitmask = ep_is_in(ep) + ? (1 << (ep_index(ep) + 16)) + : (1 << (ep_index(ep))); + + /* check if the pipe is empty */ + if (!(list_empty(&ep->queue))) { + /* Add td to the end */ + struct fsl_req *lastreq; + lastreq = list_entry(ep->queue.prev, struct fsl_req, queue); + lastreq->tail->next_td_ptr = + cpu_to_le32(req->head->td_dma & DTD_ADDR_MASK); + /* Read prime bit, if 1 goto done */ + if (fsl_readl(&dr_regs->endpointprime) & bitmask) + goto out; + + do { + /* Set ATDTW bit in USBCMD */ + temp = fsl_readl(&dr_regs->usbcmd); + fsl_writel(temp | USB_CMD_ATDTW, &dr_regs->usbcmd); + + /* Read correct status bit */ + tmp_stat = fsl_readl(&dr_regs->endptstatus) & bitmask; + + } while (!(fsl_readl(&dr_regs->usbcmd) & USB_CMD_ATDTW)); + + /* Write ATDTW bit to 0 */ + temp = fsl_readl(&dr_regs->usbcmd); + fsl_writel(temp & ~USB_CMD_ATDTW, &dr_regs->usbcmd); + + if (tmp_stat) + goto out; + } + + /* Write dQH next pointer and terminate bit to 0 */ + temp = req->head->td_dma & EP_QUEUE_HEAD_NEXT_POINTER_MASK; + dQH->next_dtd_ptr = cpu_to_le32(temp); + + /* Clear active and halt bit */ + temp = cpu_to_le32(~(EP_QUEUE_HEAD_STATUS_ACTIVE + | EP_QUEUE_HEAD_STATUS_HALT)); + dQH->size_ioc_int_sts &= temp; + + /* Prime endpoint by writing 1 to ENDPTPRIME */ + temp = ep_is_in(ep) + ? (1 << (ep_index(ep) + 16)) + : (1 << (ep_index(ep))); + fsl_writel(temp, &dr_regs->endpointprime); +out: + return 0; +} + +/* Fill in the dTD structure + * @req: request that the transfer belongs to + * @length: return actually data length of the dTD + * @dma: return dma address of the dTD + * @is_last: return flag if it is the last dTD of the request + * return: pointer to the built dTD */ +static struct ep_td_struct *fsl_build_dtd(struct fsl_req *req, unsigned *length, + dma_addr_t *dma, int *is_last) +{ + u32 swap_temp; + struct ep_td_struct *dtd; + + /* how big will this transfer be? */ + *length = min(req->req.length - req->req.actual, + (unsigned)EP_MAX_LENGTH_TRANSFER); + + dtd = dma_pool_alloc(udc_controller->td_pool, GFP_KERNEL, dma); + if (dtd == NULL) + return dtd; + + dtd->td_dma = *dma; + /* Clear reserved field */ + swap_temp = cpu_to_le32(dtd->size_ioc_sts); + swap_temp &= ~DTD_RESERVED_FIELDS; + dtd->size_ioc_sts = cpu_to_le32(swap_temp); + + /* Init all of buffer page pointers */ + swap_temp = (u32) (req->req.dma + req->req.actual); + dtd->buff_ptr0 = cpu_to_le32(swap_temp); + dtd->buff_ptr1 = cpu_to_le32(swap_temp + 0x1000); + dtd->buff_ptr2 = cpu_to_le32(swap_temp + 0x2000); + dtd->buff_ptr3 = cpu_to_le32(swap_temp + 0x3000); + dtd->buff_ptr4 = cpu_to_le32(swap_temp + 0x4000); + + req->req.actual += *length; + + /* zlp is needed if req->req.zero is set */ + if (req->req.zero) { + if (*length == 0 || (*length % req->ep->ep.maxpacket) != 0) + *is_last = 1; + else + *is_last = 0; + } else if (req->req.length == req->req.actual) + *is_last = 1; + else + *is_last = 0; + + if ((*is_last) == 0) + VDBG("multi-dtd request!\n"); + /* Fill in the transfer size; set active bit */ + swap_temp = ((*length << DTD_LENGTH_BIT_POS) | DTD_STATUS_ACTIVE); + + /* Enable interrupt for the last dtd of a request */ + if (*is_last && !req->req.no_interrupt) + swap_temp |= DTD_IOC; + + dtd->size_ioc_sts = cpu_to_le32(swap_temp); + + mb(); + + VDBG("length = %d address= 0x%x", *length, (int)*dma); + + return dtd; +} + +/* Generate dtd chain for a request */ +static int fsl_req_to_dtd(struct fsl_req *req) +{ + unsigned count; + int is_last; + int is_first =1; + struct ep_td_struct *last_dtd = NULL, *dtd; + dma_addr_t dma; + + do { + dtd = fsl_build_dtd(req, &count, &dma, &is_last); + if (dtd == NULL) + return -ENOMEM; + + if (is_first) { + is_first = 0; + req->head = dtd; + } else { + last_dtd->next_td_ptr = cpu_to_le32(dma); + last_dtd->next_td_virt = dtd; + } + last_dtd = dtd; + + req->dtd_count++; + } while (!is_last); + + dtd->next_td_ptr = cpu_to_le32(DTD_NEXT_TERMINATE); + + req->tail = dtd; + + return 0; +} + +/* queues (submits) an I/O request to an endpoint */ +static int +fsl_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) +{ + struct fsl_ep *ep = container_of(_ep, struct fsl_ep, ep); + struct fsl_req *req = container_of(_req, struct fsl_req, req); + struct fsl_udc *udc; + unsigned long flags; + int is_iso = 0; + + /* catch various bogus parameters */ + if (!_req || !req->req.complete || !req->req.buf + || !list_empty(&req->queue)) { + VDBG("%s, bad params\n", __FUNCTION__); + return -EINVAL; + } + if (!_ep || (!ep->desc && ep_index(ep))) { + VDBG("%s, bad ep\n", __FUNCTION__); + return -EINVAL; + } + if (ep->desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) { + if (req->req.length > ep->ep.maxpacket) + return -EMSGSIZE; + is_iso = 1; + } + + udc = ep->udc; + if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) + return -ESHUTDOWN; + + req->ep = ep; + + /* map virtual address to hardware */ + if (req->req.dma == DMA_ADDR_INVALID) { + req->req.dma = dma_map_single(ep->udc->gadget.dev.parent, + req->req.buf, + req->req.length, ep_is_in(ep) + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + req->mapped = 1; + } else { + dma_sync_single_for_device(ep->udc->gadget.dev.parent, + req->req.dma, req->req.length, + ep_is_in(ep) + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + req->mapped = 0; + } + + req->req.status = -EINPROGRESS; + req->req.actual = 0; + req->dtd_count = 0; + + spin_lock_irqsave(&udc->lock, flags); + + /* build dtds and push them to device queue */ + if (!fsl_req_to_dtd(req)) { + fsl_queue_td(ep, req); + } else { + spin_unlock_irqrestore(&udc->lock, flags); + return -ENOMEM; + } + + /* Update ep0 state */ + if ((ep_index(ep) == 0)) + udc->ep0_state = DATA_STATE_XMIT; + + /* irq handler advances the queue */ + if (req != NULL) + list_add_tail(&req->queue, &ep->queue); + spin_unlock_irqrestore(&udc->lock, flags); + + return 0; +} + +/* dequeues (cancels, unlinks) an I/O request from an endpoint */ +static int fsl_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) +{ + struct fsl_ep *ep = container_of(_ep, struct fsl_ep, ep); + struct fsl_req *req; + unsigned long flags; + int ep_num, stopped, ret = 0; + u32 epctrl; + + if (!_ep || !_req) + return -EINVAL; + + spin_lock_irqsave(&ep->udc->lock, flags); + stopped = ep->stopped; + + /* Stop the ep before we deal with the queue */ + ep->stopped = 1; + ep_num = ep_index(ep); + epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); + if (ep_is_in(ep)) + epctrl &= ~EPCTRL_TX_ENABLE; + else + epctrl &= ~EPCTRL_RX_ENABLE; + fsl_writel(epctrl, &dr_regs->endptctrl[ep_num]); + + /* make sure it's actually queued on this endpoint */ + list_for_each_entry(req, &ep->queue, queue) { + if (&req->req == _req) + break; + } + if (&req->req != _req) { + ret = -EINVAL; + goto out; + } + + /* The request is in progress, or completed but not dequeued */ + if (ep->queue.next == &req->queue) { + _req->status = -ECONNRESET; + fsl_ep_fifo_flush(_ep); /* flush current transfer */ + + /* The request isn't the last request in this ep queue */ + if (req->queue.next != &ep->queue) { + struct ep_queue_head *qh; + struct fsl_req *next_req; + + qh = ep->qh; + next_req = list_entry(req->queue.next, struct fsl_req, + queue); + + /* Point the QH to the first TD of next request */ + fsl_writel((u32) next_req->head, &qh->curr_dtd_ptr); + } + + /* The request hasn't been processed, patch up the TD chain */ + } else { + struct fsl_req *prev_req; + + prev_req = list_entry(req->queue.prev, struct fsl_req, queue); + fsl_writel(fsl_readl(&req->tail->next_td_ptr), + &prev_req->tail->next_td_ptr); + + } + + done(ep, req, -ECONNRESET); + + /* Enable EP */ +out: epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); + if (ep_is_in(ep)) + epctrl |= EPCTRL_TX_ENABLE; + else + epctrl |= EPCTRL_RX_ENABLE; + fsl_writel(epctrl, &dr_regs->endptctrl[ep_num]); + ep->stopped = stopped; + + spin_unlock_irqrestore(&ep->udc->lock, flags); + return ret; +} + +/*-------------------------------------------------------------------------*/ + +/*----------------------------------------------------------------- + * modify the endpoint halt feature + * @ep: the non-isochronous endpoint being stalled + * @value: 1--set halt 0--clear halt + * Returns zero, or a negative error code. +*----------------------------------------------------------------*/ +static int fsl_ep_set_halt(struct usb_ep *_ep, int value) +{ + struct fsl_ep *ep = NULL; + unsigned long flags = 0; + int status = -EOPNOTSUPP; /* operation not supported */ + unsigned char ep_dir = 0, ep_num = 0; + struct fsl_udc *udc = NULL; + + ep = container_of(_ep, struct fsl_ep, ep); + udc = ep->udc; + if (!_ep || !ep->desc) { + status = -EINVAL; + goto out; + } + + if (ep->desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) { + status = -EOPNOTSUPP; + goto out; + } + + /* Attempt to halt IN ep will fail if any transfer requests + * are still queue */ + if (value && ep_is_in(ep) && !list_empty(&ep->queue)) { + status = -EAGAIN; + goto out; + } + + status = 0; + ep_dir = ep_is_in(ep) ? USB_SEND : USB_RECV; + ep_num = (unsigned char)(ep_index(ep)); + spin_lock_irqsave(&ep->udc->lock, flags); + dr_ep_change_stall(ep_num, ep_dir, value); + spin_unlock_irqrestore(&ep->udc->lock, flags); + + if (ep_index(ep) == 0) { + udc->ep0_state = WAIT_FOR_SETUP; + udc->ep0_dir = 0; + } +out: + VDBG(" %s %s halt stat %d", ep->ep.name, + value ? "set" : "clear", status); + + return status; +} + +static void fsl_ep_fifo_flush(struct usb_ep *_ep) +{ + struct fsl_ep *ep; + int ep_num, ep_dir; + u32 bits; + unsigned long timeout; +#define FSL_UDC_FLUSH_TIMEOUT 1000 + + if (!_ep) { + return; + } else { + ep = container_of(_ep, struct fsl_ep, ep); + if (!ep->desc) + return; + } + ep_num = ep_index(ep); + ep_dir = ep_is_in(ep) ? USB_SEND : USB_RECV; + + if (ep_num == 0) + bits = (1 << 16) | 1; + else if (ep_dir == USB_SEND) + bits = 1 << (16 + ep_num); + else + bits = 1 << ep_num; + + timeout = jiffies + FSL_UDC_FLUSH_TIMEOUT; + do { + fsl_writel(bits, &dr_regs->endptflush); + + /* Wait until flush complete */ + while (fsl_readl(&dr_regs->endptflush)) { + if (time_after(jiffies, timeout)) { + ERR("ep flush timeout\n"); + return; + } + cpu_relax(); + } + /* See if we need to flush again */ + } while (fsl_readl(&dr_regs->endptstatus) & bits); +} + +static struct usb_ep_ops fsl_ep_ops = { + .enable = fsl_ep_enable, + .disable = fsl_ep_disable, + + .alloc_request = fsl_alloc_request, + .free_request = fsl_free_request, + + .alloc_buffer = fsl_alloc_buffer, + .free_buffer = fsl_free_buffer, + + .queue = fsl_ep_queue, + .dequeue = fsl_ep_dequeue, + + .set_halt = fsl_ep_set_halt, + .fifo_flush = fsl_ep_fifo_flush, /* flush fifo */ +}; + +/*------------------------------------------------------------------------- + Gadget Driver Layer Operations +-------------------------------------------------------------------------*/ + +/*---------------------------------------------------------------------- + * Get the current frame number (from DR frame_index Reg ) + *----------------------------------------------------------------------*/ +static int fsl_get_frame(struct usb_gadget *gadget) +{ + return (int)(fsl_readl(&dr_regs->frindex) & USB_FRINDEX_MASKS); +} + +/*----------------------------------------------------------------------- + * Tries to wake up the host connected to this gadget + -----------------------------------------------------------------------*/ +static int fsl_wakeup(struct usb_gadget *gadget) +{ + struct fsl_udc *udc = container_of(gadget, struct fsl_udc, gadget); + u32 portsc; + + /* Remote wakeup feature not enabled by host */ + if (!udc->remote_wakeup) + return -ENOTSUPP; + + portsc = fsl_readl(&dr_regs->portsc1); + /* not suspended? */ + if (!(portsc & PORTSCX_PORT_SUSPEND)) + return 0; + /* trigger force resume */ + portsc |= PORTSCX_PORT_FORCE_RESUME; + fsl_writel(portsc, &dr_regs->portsc1); + return 0; +} + +static int can_pullup(struct fsl_udc *udc) +{ + return udc->driver && udc->softconnect && udc->vbus_active; +} + +/* Notify controller that VBUS is powered, Called by whatever + detects VBUS sessions */ +static int fsl_vbus_session(struct usb_gadget *gadget, int is_active) +{ + struct fsl_udc *udc; + unsigned long flags; + + udc = container_of(gadget, struct fsl_udc, gadget); + spin_lock_irqsave(&udc->lock, flags); + VDBG("VBUS %s\n", is_active ? "on" : "off"); + udc->vbus_active = (is_active != 0); + if (can_pullup(udc)) + fsl_writel((fsl_readl(&dr_regs->usbcmd) | USB_CMD_RUN_STOP), + &dr_regs->usbcmd); + else + fsl_writel((fsl_readl(&dr_regs->usbcmd) & ~USB_CMD_RUN_STOP), + &dr_regs->usbcmd); + spin_unlock_irqrestore(&udc->lock, flags); + return 0; +} + +/* constrain controller's VBUS power usage + * This call is used by gadget drivers during SET_CONFIGURATION calls, + * reporting how much power the device may consume. For example, this + * could affect how quickly batteries are recharged. + * + * Returns zero on success, else negative errno. + */ +static int fsl_vbus_draw(struct usb_gadget *gadget, unsigned mA) +{ +#ifdef CONFIG_USB_OTG + struct fsl_udc *udc; + + udc = container_of(gadget, struct fsl_udc, gadget); + + if (udc->transceiver) + return otg_set_power(udc->transceiver, mA); +#endif + return -ENOTSUPP; +} + +/* Change Data+ pullup status + * this func is used by usb_gadget_connect/disconnet + */ +static int fsl_pullup(struct usb_gadget *gadget, int is_on) +{ + struct fsl_udc *udc; + + udc = container_of(gadget, struct fsl_udc, gadget); + udc->softconnect = (is_on != 0); + if (can_pullup(udc)) + fsl_writel((fsl_readl(&dr_regs->usbcmd) | USB_CMD_RUN_STOP), + &dr_regs->usbcmd); + else + fsl_writel((fsl_readl(&dr_regs->usbcmd) & ~USB_CMD_RUN_STOP), + &dr_regs->usbcmd); + + return 0; +} + +/* defined in usb_gadget.h */ +static struct usb_gadget_ops fsl_gadget_ops = { + .get_frame = fsl_get_frame, + .wakeup = fsl_wakeup, +/* .set_selfpowered = fsl_set_selfpowered, */ /* Always selfpowered */ + .vbus_session = fsl_vbus_session, + .vbus_draw = fsl_vbus_draw, + .pullup = fsl_pullup, +}; + +/* Set protocol stall on ep0, protocol stall will automatically be cleared + on new transaction */ +static void ep0stall(struct fsl_udc *udc) +{ + u32 tmp; + + /* must set tx and rx to stall at the same time */ + tmp = fsl_readl(&dr_regs->endptctrl[0]); + tmp |= EPCTRL_TX_EP_STALL | EPCTRL_RX_EP_STALL; + fsl_writel(tmp, &dr_regs->endptctrl[0]); + udc->ep0_state = WAIT_FOR_SETUP; + udc->ep0_dir = 0; +} + +/* Prime a status phase for ep0 */ +static int ep0_prime_status(struct fsl_udc *udc, int direction) +{ + struct fsl_req *req = udc->status_req; + struct fsl_ep *ep; + int status = 0; + + if (direction == EP_DIR_IN) + udc->ep0_dir = USB_DIR_IN; + else + udc->ep0_dir = USB_DIR_OUT; + + ep = &udc->eps[0]; + udc->ep0_state = WAIT_FOR_OUT_STATUS; + + req->ep = ep; + req->req.length = 0; + req->req.status = -EINPROGRESS; + req->req.actual = 0; + req->req.complete = NULL; + req->dtd_count = 0; + + if (fsl_req_to_dtd(req) == 0) + status = fsl_queue_td(ep, req); + else + return -ENOMEM; + + if (status) + ERR("Can't queue ep0 status request \n"); + list_add_tail(&req->queue, &ep->queue); + + return status; +} + +static inline int udc_reset_ep_queue(struct fsl_udc *udc, u8 pipe) +{ + struct fsl_ep *ep = get_ep_by_pipe(udc, pipe); + + if (!ep->name) + return 0; + + nuke(ep, -ESHUTDOWN); + + return 0; +} + +/* + * ch9 Set address + */ +static void ch9setaddress(struct fsl_udc *udc, u16 value, u16 index, u16 length) +{ + /* Save the new address to device struct */ + udc->device_address = (u8) value; + /* Update usb state */ + udc->usb_state = USB_STATE_ADDRESS; + /* Status phase */ + if (ep0_prime_status(udc, EP_DIR_IN)) + ep0stall(udc); +} + +/* + * ch9 Get status + */ +static void ch9getstatus(struct fsl_udc *udc, u8 request_type, u16 value, + u16 index, u16 length) +{ + u16 tmp = 0; /* Status, cpu endian */ + + struct fsl_req *req; + struct fsl_ep *ep; + int status = 0; + + ep = &udc->eps[0]; + + if ((request_type & USB_RECIP_MASK) == USB_RECIP_DEVICE) { + /* Get device status */ + tmp = 1 << USB_DEVICE_SELF_POWERED; + tmp |= udc->remote_wakeup << USB_DEVICE_REMOTE_WAKEUP; + } else if ((request_type & USB_RECIP_MASK) == USB_RECIP_INTERFACE) { + /* Get interface status */ + /* We don't have interface information in udc driver */ + tmp = 0; + } else if ((request_type & USB_RECIP_MASK) == USB_RECIP_ENDPOINT) { + /* Get endpoint status */ + struct fsl_ep *target_ep; + + target_ep = get_ep_by_pipe(udc, get_pipe_by_windex(index)); + + /* stall if endpoint doesn't exist */ + if (!target_ep->desc) + goto stall; + tmp = dr_ep_get_stall(ep_index(target_ep), ep_is_in(target_ep)) + << USB_ENDPOINT_HALT; + } + + udc->ep0_dir = USB_DIR_IN; + /* Borrow the per device status_req */ + req = udc->status_req; + /* Fill in the reqest structure */ + *((u16 *) req->req.buf) = cpu_to_le16(tmp); + req->ep = ep; + req->req.length = 2; + req->req.status = -EINPROGRESS; + req->req.actual = 0; + req->req.complete = NULL; + req->dtd_count = 0; + + /* prime the data phase */ + if ((fsl_req_to_dtd(req) == 0)) + status = fsl_queue_td(ep, req); + else /* no mem */ + goto stall; + + if (status) { + ERR("Can't respond to getstatus request \n"); + goto stall; + } + list_add_tail(&req->queue, &ep->queue); + udc->ep0_state = DATA_STATE_XMIT; + return; +stall: + ep0stall(udc); +} + +static void setup_received_irq(struct fsl_udc *udc, + struct usb_ctrlrequest *setup) +{ + u16 wValue = le16_to_cpu(setup->wValue); + u16 wIndex = le16_to_cpu(setup->wIndex); + u16 wLength = le16_to_cpu(setup->wLength); + + udc_reset_ep_queue(udc, 0); + + switch (setup->bRequest) { + /* Request that need Data+Status phase from udc */ + case USB_REQ_GET_STATUS: + if ((setup->bRequestType & (USB_DIR_IN | USB_TYPE_STANDARD)) + != (USB_DIR_IN | USB_TYPE_STANDARD)) + break; + ch9getstatus(udc, setup->bRequestType, wValue, wIndex, wLength); + break; + + /* Requests that need Status phase from udc */ + case USB_REQ_SET_ADDRESS: + if (setup->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD + | USB_RECIP_DEVICE)) + break; + ch9setaddress(udc, wValue, wIndex, wLength); + break; + + /* Handled by udc, no data, status by udc */ + case USB_REQ_CLEAR_FEATURE: + case USB_REQ_SET_FEATURE: + { /* status transaction */ + int rc = -EOPNOTSUPP; + + if ((setup->bRequestType & USB_RECIP_MASK) + == USB_RECIP_ENDPOINT) { + int pipe = get_pipe_by_windex(wIndex); + struct fsl_ep *ep; + + if (wValue != 0 || wLength != 0 || pipe > udc->max_ep) + break; + ep = get_ep_by_pipe(udc, pipe); + + spin_unlock(&udc->lock); + rc = fsl_ep_set_halt(&ep->ep, + (setup->bRequest == USB_REQ_SET_FEATURE) + ? 1 : 0); + spin_lock(&udc->lock); + + } else if ((setup->bRequestType & USB_RECIP_MASK) + == USB_RECIP_DEVICE) { + /* Note: The driver has not include OTG support yet. + * This will be set when OTG support is added */ + if (!udc->gadget.is_otg) + break; + else if (setup->bRequest == USB_DEVICE_B_HNP_ENABLE) + udc->gadget.b_hnp_enable = 1; + else if (setup->bRequest == USB_DEVICE_A_HNP_SUPPORT) + udc->gadget.a_hnp_support = 1; + else if (setup->bRequest == + USB_DEVICE_A_ALT_HNP_SUPPORT) + udc->gadget.a_alt_hnp_support = 1; + rc = 0; + } + if (rc == 0) { + if (ep0_prime_status(udc, EP_DIR_IN)) + ep0stall(udc); + } + break; + } + /* Requests handled by gadget */ + default: + if (wLength) { + /* Data phase from gadget, status phase from udc */ + udc->ep0_dir = (setup->bRequestType & USB_DIR_IN) + ? USB_DIR_IN : USB_DIR_OUT; + spin_unlock(&udc->lock); + if (udc->driver->setup(&udc->gadget, + &udc->local_setup_buff) < 0) + ep0stall(udc); + spin_lock(&udc->lock); + udc->ep0_state = (setup->bRequestType & USB_DIR_IN) + ? DATA_STATE_XMIT : DATA_STATE_RECV; + + } else { + /* No data phase, IN status from gadget */ + udc->ep0_dir = USB_DIR_IN; + spin_unlock(&udc->lock); + if (udc->driver->setup(&udc->gadget, + &udc->local_setup_buff) < 0) + ep0stall(udc); + spin_lock(&udc->lock); + udc->ep0_state = WAIT_FOR_OUT_STATUS; + } + break; + } +} + +/* Process request for Data or Status phase of ep0 + * prime status phase if needed */ +static void ep0_req_complete(struct fsl_udc *udc, struct fsl_ep *ep0, + struct fsl_req *req) +{ + if (udc->usb_state == USB_STATE_ADDRESS) { + /* Set the new address */ + u32 new_address = (u32) udc->device_address; + fsl_writel(new_address << USB_DEVICE_ADDRESS_BIT_POS, + &dr_regs->deviceaddr); + } + + done(ep0, req, 0); + + switch (udc->ep0_state) { + case DATA_STATE_XMIT: + /* receive status phase */ + if (ep0_prime_status(udc, EP_DIR_OUT)) + ep0stall(udc); + break; + case DATA_STATE_RECV: + /* send status phase */ + if (ep0_prime_status(udc, EP_DIR_IN)) + ep0stall(udc); + break; + case WAIT_FOR_OUT_STATUS: + udc->ep0_state = WAIT_FOR_SETUP; + break; + case WAIT_FOR_SETUP: + ERR("Unexpect ep0 packets \n"); + break; + default: + ep0stall(udc); + break; + } +} + +/* Tripwire mechanism to ensure a setup packet payload is extracted without + * being corrupted by another incoming setup packet */ +static void tripwire_handler(struct fsl_udc *udc, u8 ep_num, u8 *buffer_ptr) +{ + u32 temp; + struct ep_queue_head *qh; + + qh = &udc->ep_qh[ep_num * 2 + EP_DIR_OUT]; + + /* Clear bit in ENDPTSETUPSTAT */ + temp = fsl_readl(&dr_regs->endptsetupstat); + fsl_writel(temp | (1 << ep_num), &dr_regs->endptsetupstat); + + /* while a hazard exists when setup package arrives */ + do { + /* Set Setup Tripwire */ + temp = fsl_readl(&dr_regs->usbcmd); + fsl_writel(temp | USB_CMD_SUTW, &dr_regs->usbcmd); + + /* Copy the setup packet to local buffer */ + memcpy(buffer_ptr, (u8 *) qh->setup_buffer, 8); + } while (!(fsl_readl(&dr_regs->usbcmd) & USB_CMD_SUTW)); + + /* Clear Setup Tripwire */ + temp = fsl_readl(&dr_regs->usbcmd); + fsl_writel(temp & ~USB_CMD_SUTW, &dr_regs->usbcmd); +} + +/* process-ep_req(): free the completed Tds for this req */ +static int process_ep_req(struct fsl_udc *udc, int pipe, + struct fsl_req *curr_req) +{ + struct ep_td_struct *curr_td; + int td_complete, actual, remaining_length, j, tmp; + int status = 0; + int errors = 0; + struct ep_queue_head *curr_qh = &udc->ep_qh[pipe]; + int direction = pipe % 2; + + curr_td = curr_req->head; + td_complete = 0; + actual = curr_req->req.length; + + for (j = 0; j < curr_req->dtd_count; j++) { + remaining_length = (le32_to_cpu(curr_td->size_ioc_sts) + & DTD_PACKET_SIZE) + >> DTD_LENGTH_BIT_POS; + actual -= remaining_length; + + if ((errors = le32_to_cpu(curr_td->size_ioc_sts) & + DTD_ERROR_MASK)) { + if (errors & DTD_STATUS_HALTED) { + ERR("dTD error %08x QH=%d\n", errors, pipe); + /* Clear the errors and Halt condition */ + tmp = le32_to_cpu(curr_qh->size_ioc_int_sts); + tmp &= ~errors; + curr_qh->size_ioc_int_sts = cpu_to_le32(tmp); + status = -EPIPE; + /* FIXME: continue with next queued TD? */ + + break; + } + if (errors & DTD_STATUS_DATA_BUFF_ERR) { + VDBG("Transfer overflow"); + status = -EPROTO; + break; + } else if (errors & DTD_STATUS_TRANSACTION_ERR) { + VDBG("ISO error"); + status = -EILSEQ; + break; + } else + ERR("Unknown error has occured (0x%x)!\r\n", + errors); + + } else if (le32_to_cpu(curr_td->size_ioc_sts) + & DTD_STATUS_ACTIVE) { + VDBG("Request not complete"); + status = REQ_UNCOMPLETE; + return status; + } else if (remaining_length) { + if (direction) { + VDBG("Transmit dTD remaining length not zero"); + status = -EPROTO; + break; + } else { + td_complete++; + break; + } + } else { + td_complete++; + VDBG("dTD transmitted successful "); + } + + if (j != curr_req->dtd_count - 1) + curr_td = (struct ep_td_struct *)curr_td->next_td_virt; + } + + if (status) + return status; + + curr_req->req.actual = actual; + + return 0; +} + +/* Process a DTD completion interrupt */ +static void dtd_complete_irq(struct fsl_udc *udc) +{ + u32 bit_pos; + int i, ep_num, direction, bit_mask, status; + struct fsl_ep *curr_ep; + struct fsl_req *curr_req, *temp_req; + + /* Clear the bits in the register */ + bit_pos = fsl_readl(&dr_regs->endptcomplete); + fsl_writel(bit_pos, &dr_regs->endptcomplete); + + if (!bit_pos) + return; + + for (i = 0; i < udc->max_ep * 2; i++) { + ep_num = i >> 1; + direction = i % 2; + + bit_mask = 1 << (ep_num + 16 * direction); + + if (!(bit_pos & bit_mask)) + continue; + + curr_ep = get_ep_by_pipe(udc, i); + + /* If the ep is configured */ + if (curr_ep->name == NULL) { + WARN("Invalid EP?"); + continue; + } + + /* process the req queue until an uncomplete request */ + list_for_each_entry_safe(curr_req, temp_req, &curr_ep->queue, + queue) { + status = process_ep_req(udc, i, curr_req); + + VDBG("status of process_ep_req= %d, ep = %d", + status, ep_num); + if (status == REQ_UNCOMPLETE) + break; + /* write back status to req */ + curr_req->req.status = status; + + if (ep_num == 0) { + ep0_req_complete(udc, curr_ep, curr_req); + break; + } else + done(curr_ep, curr_req, status); + } + } +} + +/* Process a port change interrupt */ +static void port_change_irq(struct fsl_udc *udc) +{ + u32 speed; + + if (udc->bus_reset) + udc->bus_reset = 0; + + /* Bus resetting is finished */ + if (!(fsl_readl(&dr_regs->portsc1) & PORTSCX_PORT_RESET)) { + /* Get the speed */ + speed = (fsl_readl(&dr_regs->portsc1) + & PORTSCX_PORT_SPEED_MASK); + switch (speed) { + case PORTSCX_PORT_SPEED_HIGH: + udc->gadget.speed = USB_SPEED_HIGH; + break; + case PORTSCX_PORT_SPEED_FULL: + udc->gadget.speed = USB_SPEED_FULL; + break; + case PORTSCX_PORT_SPEED_LOW: + udc->gadget.speed = USB_SPEED_LOW; + break; + default: + udc->gadget.speed = USB_SPEED_UNKNOWN; + break; + } + } + + /* Update USB state */ + if (!udc->resume_state) + udc->usb_state = USB_STATE_DEFAULT; +} + +/* Process suspend interrupt */ +static void suspend_irq(struct fsl_udc *udc) +{ + udc->resume_state = udc->usb_state; + udc->usb_state = USB_STATE_SUSPENDED; + + /* report suspend to the driver, serial.c does not support this */ + if (udc->driver->suspend) + udc->driver->suspend(&udc->gadget); +} + +static void bus_resume(struct fsl_udc *udc) +{ + udc->usb_state = udc->resume_state; + udc->resume_state = 0; + + /* report resume to the driver, serial.c does not support this */ + if (udc->driver->resume) + udc->driver->resume(&udc->gadget); +} + +/* Clear up all ep queues */ +static int reset_queues(struct fsl_udc *udc) +{ + u8 pipe; + + for (pipe = 0; pipe < udc->max_pipes; pipe++) + udc_reset_ep_queue(udc, pipe); + + /* report disconnect; the driver is already quiesced */ + udc->driver->disconnect(&udc->gadget); + + return 0; +} + +/* Process reset interrupt */ +static void reset_irq(struct fsl_udc *udc) +{ + u32 temp; + unsigned long timeout; + + /* Clear the device address */ + temp = fsl_readl(&dr_regs->deviceaddr); + fsl_writel(temp & ~USB_DEVICE_ADDRESS_MASK, &dr_regs->deviceaddr); + + udc->device_address = 0; + + /* Clear usb state */ + udc->resume_state = 0; + udc->ep0_dir = 0; + udc->ep0_state = WAIT_FOR_SETUP; + udc->remote_wakeup = 0; /* default to 0 on reset */ + udc->gadget.b_hnp_enable = 0; + udc->gadget.a_hnp_support = 0; + udc->gadget.a_alt_hnp_support = 0; + + /* Clear all the setup token semaphores */ + temp = fsl_readl(&dr_regs->endptsetupstat); + fsl_writel(temp, &dr_regs->endptsetupstat); + + /* Clear all the endpoint complete status bits */ + temp = fsl_readl(&dr_regs->endptcomplete); + fsl_writel(temp, &dr_regs->endptcomplete); + + timeout = jiffies + 100; + while (fsl_readl(&dr_regs->endpointprime)) { + /* Wait until all endptprime bits cleared */ + if (time_after(jiffies, timeout)) { + ERR("Timeout for reset\n"); + break; + } + cpu_relax(); + } + + /* Write 1s to the flush register */ + fsl_writel(0xffffffff, &dr_regs->endptflush); + + if (fsl_readl(&dr_regs->portsc1) & PORTSCX_PORT_RESET) { + VDBG("Bus reset"); + /* Bus is reseting */ + udc->bus_reset = 1; + /* Reset all the queues, include XD, dTD, EP queue + * head and TR Queue */ + reset_queues(udc); + udc->usb_state = USB_STATE_DEFAULT; + } else { + VDBG("Controller reset"); + /* initialize usb hw reg except for regs for EP, not + * touch usbintr reg */ + dr_controller_setup(udc); + + /* Reset all internal used Queues */ + reset_queues(udc); + + ep0_setup(udc); + + /* Enable DR IRQ reg, Set Run bit, change udc state */ + dr_controller_run(udc); + udc->usb_state = USB_STATE_ATTACHED; + } +} + +/* + * USB device controller interrupt handler + */ +static irqreturn_t fsl_udc_irq(int irq, void *_udc) +{ + struct fsl_udc *udc = _udc; + u32 irq_src; + irqreturn_t status = IRQ_NONE; + unsigned long flags; + + /* Disable ISR for OTG host mode */ + if (udc->stopped) + return IRQ_NONE; + spin_lock_irqsave(&udc->lock, flags); + irq_src = fsl_readl(&dr_regs->usbsts) & fsl_readl(&dr_regs->usbintr); + /* Clear notification bits */ + fsl_writel(irq_src, &dr_regs->usbsts); + + /* VDBG("irq_src [0x%8x]", irq_src); */ + + /* Need to resume? */ + if (udc->usb_state == USB_STATE_SUSPENDED) + if ((fsl_readl(&dr_regs->portsc1) & PORTSCX_PORT_SUSPEND) == 0) + bus_resume(udc); + + /* USB Interrupt */ + if (irq_src & USB_STS_INT) { + VDBG("Packet int"); + /* Setup package, we only support ep0 as control ep */ + if (fsl_readl(&dr_regs->endptsetupstat) & EP_SETUP_STATUS_EP0) { + tripwire_handler(udc, 0, + (u8 *) (&udc->local_setup_buff)); + setup_received_irq(udc, &udc->local_setup_buff); + status = IRQ_HANDLED; + } + + /* completion of dtd */ + if (fsl_readl(&dr_regs->endptcomplete)) { + dtd_complete_irq(udc); + status = IRQ_HANDLED; + } + } + + /* SOF (for ISO transfer) */ + if (irq_src & USB_STS_SOF) { + status = IRQ_HANDLED; + } + + /* Port Change */ + if (irq_src & USB_STS_PORT_CHANGE) { + port_change_irq(udc); + status = IRQ_HANDLED; + } + + /* Reset Received */ + if (irq_src & USB_STS_RESET) { + reset_irq(udc); + status = IRQ_HANDLED; + } + + /* Sleep Enable (Suspend) */ + if (irq_src & USB_STS_SUSPEND) { + suspend_irq(udc); + status = IRQ_HANDLED; + } + + if (irq_src & (USB_STS_ERR | USB_STS_SYS_ERR)) { + VDBG("Error IRQ %x ", irq_src); + } + + spin_unlock_irqrestore(&udc->lock, flags); + return status; +} + +/*----------------------------------------------------------------* + * Hook to gadget drivers + * Called by initialization code of gadget drivers +*----------------------------------------------------------------*/ +int usb_gadget_register_driver(struct usb_gadget_driver *driver) +{ + int retval = -ENODEV; + unsigned long flags = 0; + + if (!udc_controller) + return -ENODEV; + + if (!driver || (driver->speed != USB_SPEED_FULL + && driver->speed != USB_SPEED_HIGH) + || !driver->bind || !driver->disconnect + || !driver->setup) + return -EINVAL; + + if (udc_controller->driver) + return -EBUSY; + + /* lock is needed but whether should use this lock or another */ + spin_lock_irqsave(&udc_controller->lock, flags); + + driver->driver.bus = 0; + /* hook up the driver */ + udc_controller->driver = driver; + udc_controller->gadget.dev.driver = &driver->driver; + spin_unlock_irqrestore(&udc_controller->lock, flags); + + /* bind udc driver to gadget driver */ + retval = driver->bind(&udc_controller->gadget); + if (retval) { + VDBG("bind to %s --> %d", driver->driver.name, retval); + udc_controller->gadget.dev.driver = 0; + udc_controller->driver = 0; + goto out; + } + + /* Enable DR IRQ reg and Set usbcmd reg Run bit */ + dr_controller_run(udc_controller); + udc_controller->usb_state = USB_STATE_ATTACHED; + udc_controller->ep0_state = WAIT_FOR_SETUP; + udc_controller->ep0_dir = 0; + printk(KERN_INFO "%s: bind to driver %s \n", + udc_controller->gadget.name, driver->driver.name); + +out: + if (retval) + printk("retval %d \n", retval); + return retval; +} +EXPORT_SYMBOL(usb_gadget_register_driver); + +/* Disconnect from gadget driver */ +int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) +{ + struct fsl_ep *loop_ep; + unsigned long flags; + + if (!udc_controller) + return -ENODEV; + + if (!driver || driver != udc_controller->driver || !driver->unbind) + return -EINVAL; + +#ifdef CONFIG_USB_OTG + if (udc_controller->transceiver) + (void)otg_set_peripheral(udc_controller->transceiver, 0); +#endif + + /* stop DR, disable intr */ + dr_controller_stop(udc_controller); + + /* in fact, no needed */ + udc_controller->usb_state = USB_STATE_ATTACHED; + udc_controller->ep0_state = WAIT_FOR_SETUP; + udc_controller->ep0_dir = 0; + + /* stand operation */ + spin_lock_irqsave(&udc_controller->lock, flags); + udc_controller->gadget.speed = USB_SPEED_UNKNOWN; + nuke(&udc_controller->eps[0], -ESHUTDOWN); + list_for_each_entry(loop_ep, &udc_controller->gadget.ep_list, + ep.ep_list) + nuke(loop_ep, -ESHUTDOWN); + spin_unlock_irqrestore(&udc_controller->lock, flags); + + /* unbind gadget and unhook driver. */ + driver->unbind(&udc_controller->gadget); + udc_controller->gadget.dev.driver = 0; + udc_controller->driver = 0; + + printk("unregistered gadget driver '%s'\r\n", driver->driver.name); + return 0; +} +EXPORT_SYMBOL(usb_gadget_unregister_driver); + +/*------------------------------------------------------------------------- + PROC File System Support +-------------------------------------------------------------------------*/ +#ifdef CONFIG_USB_GADGET_DEBUG_FILES + +#include <linux/seq_file.h> + +static const char proc_filename[] = "driver/fsl_usb2_udc"; + +static int fsl_proc_read(char *page, char **start, off_t off, int count, + int *eof, void *_dev) +{ + char *buf = page; + char *next = buf; + unsigned size = count; + unsigned long flags; + int t, i; + u32 tmp_reg; + struct fsl_ep *ep = NULL; + struct fsl_req *req; + + struct fsl_udc *udc = udc_controller; + if (off != 0) + return 0; + + spin_lock_irqsave(&udc->lock, flags); + + /* ------basic driver infomation ---- */ + t = scnprintf(next, size, + DRIVER_DESC "\n" + "%s version: %s\n" + "Gadget driver: %s\n\n", + driver_name, DRIVER_VERSION, + udc->driver ? udc->driver->driver.name : "(none)"); + size -= t; + next += t; + + /* ------ DR Registers ----- */ + tmp_reg = fsl_readl(&dr_regs->usbcmd); + t = scnprintf(next, size, + "USBCMD reg:\n" + "SetupTW: %d\n" + "Run/Stop: %s\n\n", + (tmp_reg & USB_CMD_SUTW) ? 1 : 0, + (tmp_reg & USB_CMD_RUN_STOP) ? "Run" : "Stop"); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->usbsts); + t = scnprintf(next, size, + "USB Status Reg:\n" + "Dr Suspend: %d" "Reset Received: %d" "System Error: %s" + "USB Error Interrupt: %s\n\n", + (tmp_reg & USB_STS_SUSPEND) ? 1 : 0, + (tmp_reg & USB_STS_RESET) ? 1 : 0, + (tmp_reg & USB_STS_SYS_ERR) ? "Err" : "Normal", + (tmp_reg & USB_STS_ERR) ? "Err detected" : "No err"); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->usbintr); + t = scnprintf(next, size, + "USB Intrrupt Enable Reg:\n" + "Sleep Enable: %d" "SOF Received Enable: %d" + "Reset Enable: %d\n" + "System Error Enable: %d" + "Port Change Dectected Enable: %d\n" + "USB Error Intr Enable: %d" "USB Intr Enable: %d\n\n", + (tmp_reg & USB_INTR_DEVICE_SUSPEND) ? 1 : 0, + (tmp_reg & USB_INTR_SOF_EN) ? 1 : 0, + (tmp_reg & USB_INTR_RESET_EN) ? 1 : 0, + (tmp_reg & USB_INTR_SYS_ERR_EN) ? 1 : 0, + (tmp_reg & USB_INTR_PTC_DETECT_EN) ? 1 : 0, + (tmp_reg & USB_INTR_ERR_INT_EN) ? 1 : 0, + (tmp_reg & USB_INTR_INT_EN) ? 1 : 0); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->frindex); + t = scnprintf(next, size, + "USB Frame Index Reg:" "Frame Number is 0x%x\n\n", + (tmp_reg & USB_FRINDEX_MASKS)); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->deviceaddr); + t = scnprintf(next, size, + "USB Device Address Reg:" "Device Addr is 0x%x\n\n", + (tmp_reg & USB_DEVICE_ADDRESS_MASK)); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->endpointlistaddr); + t = scnprintf(next, size, + "USB Endpoint List Address Reg:" + "Device Addr is 0x%x\n\n", + (tmp_reg & USB_EP_LIST_ADDRESS_MASK)); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->portsc1); + t = scnprintf(next, size, + "USB Port Status&Control Reg:\n" + "Port Transceiver Type : %s" "Port Speed: %s \n" + "PHY Low Power Suspend: %s" "Port Reset: %s" + "Port Suspend Mode: %s \n" "Over-current Change: %s" + "Port Enable/Disable Change: %s\n" + "Port Enabled/Disabled: %s" + "Current Connect Status: %s\n\n", ( { + char *s; + switch (tmp_reg & PORTSCX_PTS_FSLS) { + case PORTSCX_PTS_UTMI: + s = "UTMI"; break; + case PORTSCX_PTS_ULPI: + s = "ULPI "; break; + case PORTSCX_PTS_FSLS: + s = "FS/LS Serial"; break; + default: + s = "None"; break; + } + s;} ), ( { + char *s; + switch (tmp_reg & PORTSCX_PORT_SPEED_UNDEF) { + case PORTSCX_PORT_SPEED_FULL: + s = "Full Speed"; break; + case PORTSCX_PORT_SPEED_LOW: + s = "Low Speed"; break; + case PORTSCX_PORT_SPEED_HIGH: + s = "High Speed"; break; + default: + s = "Undefined"; break; + } + s; + } ), + (tmp_reg & PORTSCX_PHY_LOW_POWER_SPD) ? + "Normal PHY mode" : "Low power mode", + (tmp_reg & PORTSCX_PORT_RESET) ? "In Reset" : + "Not in Reset", + (tmp_reg & PORTSCX_PORT_SUSPEND) ? "In " : "Not in", + (tmp_reg & PORTSCX_OVER_CURRENT_CHG) ? "Dected" : + "No", + (tmp_reg & PORTSCX_PORT_EN_DIS_CHANGE) ? "Disable" : + "Not change", + (tmp_reg & PORTSCX_PORT_ENABLE) ? "Enable" : + "Not correct", + (tmp_reg & PORTSCX_CURRENT_CONNECT_STATUS) ? + "Attached" : "Not-Att"); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->usbmode); + t = scnprintf(next, size, + "USB Mode Reg:" "Controller Mode is : %s\n\n", ( { + char *s; + switch (tmp_reg & USB_MODE_CTRL_MODE_HOST) { + case USB_MODE_CTRL_MODE_IDLE: + s = "Idle"; break; + case USB_MODE_CTRL_MODE_DEVICE: + s = "Device Controller"; break; + case USB_MODE_CTRL_MODE_HOST: + s = "Host Controller"; break; + default: + s = "None"; break; + } + s; + } )); + size -= t; + next += t; + + tmp_reg = fsl_readl(&dr_regs->endptsetupstat); + t = scnprintf(next, size, + "Endpoint Setup Status Reg:" "SETUP on ep 0x%x\n\n", + (tmp_reg & EP_SETUP_STATUS_MASK)); + size -= t; + next += t; + + for (i = 0; i < udc->max_ep / 2; i++) { + tmp_reg = fsl_readl(&dr_regs->endptctrl[i]); + t = scnprintf(next, size, "EP Ctrl Reg [0x%x]: = [0x%x]\n", + i, tmp_reg); + size -= t; + next += t; + } + tmp_reg = fsl_readl(&dr_regs->endpointprime); + t = scnprintf(next, size, "EP Prime Reg = [0x%x]\n", tmp_reg); + size -= t; + next += t; + + tmp_reg = usb_sys_regs->snoop1; + t = scnprintf(next, size, "\nSnoop1 Reg : = [0x%x]\n\n", tmp_reg); + size -= t; + next += t; + + tmp_reg = usb_sys_regs->control; + t = scnprintf(next, size, "General Control Reg : = [0x%x]\n\n", + tmp_reg); + size -= t; + next += t; + + /* ------fsl_udc, fsl_ep, fsl_request structure information ----- */ + ep = &udc->eps[0]; + t = scnprintf(next, size, "For %s Maxpkt is 0x%x index is 0x%x\n", + ep->ep.name, ep_maxpacket(ep), ep_index(ep)); + size -= t; + next += t; + + if (list_empty(&ep->queue)) { + t = scnprintf(next, size, "its req queue is empty\n\n"); + size -= t; + next += t; + } else { + list_for_each_entry(req, &ep->queue, queue) { + t = scnprintf(next, size, + "req %p actual 0x%x length 0x%x buf %p\n", + &req->req, req->req.actual, + req->req.length, req->req.buf); + size -= t; + next += t; + } + } + /* other gadget->eplist ep */ + list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) { + if (ep->desc) { + t = scnprintf(next, size, + "\nFor %s Maxpkt is 0x%x " + "index is 0x%x\n", + ep->ep.name, ep_maxpacket(ep), + ep_index(ep)); + size -= t; + next += t; + + if (list_empty(&ep->queue)) { + t = scnprintf(next, size, + "its req queue is empty\n\n"); + size -= t; + next += t; + } else { + list_for_each_entry(req, &ep->queue, queue) { + t = scnprintf(next, size, + "req %p actual 0x%x length" + "0x%x buf %p\n", + &req->req, req->req.actual, + req->req.length, req->req.buf); + size -= t; + next += t; + } /* end for each_entry of ep req */ + } /* end for else */ + } /* end for if(ep->queue) */ + } /* end (ep->desc) */ + + spin_unlock_irqrestore(&udc->lock, flags); + + *eof = 1; + return count - size; +} + +#define create_proc_file() create_proc_read_entry(proc_filename, \ + 0, NULL, fsl_proc_read, NULL) + +#define remove_proc_file() remove_proc_entry(proc_filename, NULL) + +#else /* !CONFIG_USB_GADGET_DEBUG_FILES */ + +#define create_proc_file() do {} while (0) +#define remove_proc_file() do {} while (0) + +#endif /* CONFIG_USB_GADGET_DEBUG_FILES */ + +/*-------------------------------------------------------------------------*/ + +/* Release udc structures */ +static void fsl_udc_release(struct device *dev) +{ + complete(udc_controller->done); + dma_free_coherent(dev, udc_controller->ep_qh_size, + udc_controller->ep_qh, udc_controller->ep_qh_dma); + kfree(udc_controller); +} + +/****************************************************************** + Internal structure setup functions +*******************************************************************/ +/*------------------------------------------------------------------ + * init resource for globle controller + * Return the udc handle on success or NULL on failure + ------------------------------------------------------------------*/ +static struct fsl_udc *__init struct_udc_setup(struct platform_device *pdev) +{ + struct fsl_udc *udc; + struct fsl_usb2_platform_data *pdata; + size_t size; + + udc = kzalloc(sizeof(struct fsl_udc), GFP_KERNEL); + if (udc == NULL) { + ERR("malloc udc failed\n"); + return NULL; + } + + pdata = pdev->dev.platform_data; + udc->phy_mode = pdata->phy_mode; + /* max_ep_nr is bidirectional ep number, max_ep doubles the number */ + udc->max_ep = pdata->max_ep_nr * 2; + + udc->eps = kzalloc(sizeof(struct fsl_ep) * udc->max_ep, GFP_KERNEL); + if (!udc->eps) { + ERR("malloc fsl_ep failed\n"); + goto cleanup; + } + + /* initialized QHs, take care of alignment */ + size = udc->max_ep * sizeof(struct ep_queue_head); + if (size < QH_ALIGNMENT) + size = QH_ALIGNMENT; + else if ((size % QH_ALIGNMENT) != 0) { + size += QH_ALIGNMENT + 1; + size &= ~(QH_ALIGNMENT - 1); + } + udc->ep_qh = dma_alloc_coherent(&pdev->dev, size, + &udc->ep_qh_dma, GFP_KERNEL); + if (!udc->ep_qh) { + ERR("malloc QHs for udc failed\n"); + kfree(udc->eps); + goto cleanup; + } + + udc->ep_qh_size = size; + + /* Initialize ep0 status request structure */ + /* FIXME: fsl_alloc_request() ignores ep argument */ + udc->status_req = container_of(fsl_alloc_request(NULL, GFP_KERNEL), + struct fsl_req, req); + /* allocate a small amount of memory to get valid address */ + udc->status_req->req.buf = kmalloc(8, GFP_KERNEL); + udc->status_req->req.dma = virt_to_phys(udc->status_req->req.buf); + + udc->resume_state = USB_STATE_NOTATTACHED; + udc->usb_state = USB_STATE_POWERED; + udc->ep0_dir = 0; + udc->remote_wakeup = 0; /* default to 0 on reset */ + spin_lock_init(&udc->lock); + + return udc; + +cleanup: + kfree(udc); + return NULL; +} + +/*---------------------------------------------------------------- + * Setup the fsl_ep struct for eps + * Link fsl_ep->ep to gadget->ep_list + * ep0out is not used so do nothing here + * ep0in should be taken care + *--------------------------------------------------------------*/ +static int __init struct_ep_setup(struct fsl_udc *udc, unsigned char index, + char *name, int link) +{ + struct fsl_ep *ep = &udc->eps[index]; + + ep->udc = udc; + strcpy(ep->name, name); + ep->ep.name = ep->name; + + ep->ep.ops = &fsl_ep_ops; + ep->stopped = 0; + + /* for ep0: maxP defined in desc + * for other eps, maxP is set by epautoconfig() called by gadget layer + */ + ep->ep.maxpacket = (unsigned short) ~0; + + /* the queue lists any req for this ep */ + INIT_LIST_HEAD(&ep->queue); + + /* gagdet.ep_list used for ep_autoconfig so no ep0 */ + if (link) + list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list); + ep->gadget = &udc->gadget; + ep->qh = &udc->ep_qh[index]; + + return 0; +} + +/* Driver probe function + * all intialize operations implemented here except enabling usb_intr reg + */ +static int __init fsl_udc_probe(struct platform_device *pdev) +{ + struct resource *res; + int ret = -ENODEV; + unsigned int i; + + if (strcmp(pdev->name, driver_name)) { + VDBG("Wrong device\n"); + return -ENODEV; + } + + /* board setup should have been done in the platform code */ + + /* Initialize the udc structure including QH member and other member */ + udc_controller = struct_udc_setup(pdev); + if (!udc_controller) { + VDBG("udc_controller is NULL \n"); + return -ENOMEM; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -ENXIO; + + if (!request_mem_region(res->start, res->end - res->start + 1, + driver_name)) { + ERR("request mem region for %s failed \n", pdev->name); + return -EBUSY; + } + + dr_regs = ioremap(res->start, res->end - res->start + 1); + if (!dr_regs) { + ret = -ENOMEM; + goto err1; + } + + usb_sys_regs = (struct usb_sys_interface *) + ((u32)dr_regs + USB_DR_SYS_OFFSET); + + udc_controller->irq = platform_get_irq(pdev, 0); + if (!udc_controller->irq) { + ret = -ENODEV; + goto err2; + } + + ret = request_irq(udc_controller->irq, fsl_udc_irq, SA_SHIRQ, + driver_name, udc_controller); + if (ret != 0) { + ERR("cannot request irq %d err %d \n", + udc_controller->irq, ret); + goto err2; + } + + /* initialize usb hw reg except for regs for EP, + * leave usbintr reg untouched */ + dr_controller_setup(udc_controller); + + /* Setup gadget structure */ + udc_controller->gadget.ops = &fsl_gadget_ops; + udc_controller->gadget.is_dualspeed = 1; + udc_controller->gadget.ep0 = &udc_controller->eps[0].ep; + INIT_LIST_HEAD(&udc_controller->gadget.ep_list); + udc_controller->gadget.speed = USB_SPEED_UNKNOWN; + udc_controller->gadget.name = driver_name; + + /* Setup gadget.dev and register with kernel */ + strcpy(udc_controller->gadget.dev.bus_id, "gadget"); + udc_controller->gadget.dev.release = fsl_udc_release; + udc_controller->gadget.dev.parent = &pdev->dev; + ret = device_register(&udc_controller->gadget.dev); + if (ret < 0) + goto err3; + + /* setup QH and epctrl for ep0 */ + ep0_setup(udc_controller); + + /* setup udc->eps[] for ep0 */ + struct_ep_setup(udc_controller, 0, "ep0", 0); + /* for ep0: the desc defined here; + * for other eps, gadget layer called ep_enable with defined desc + */ + udc_controller->eps[0].desc = &fsl_ep0_desc; + udc_controller->eps[0].ep.maxpacket = USB_MAX_CTRL_PAYLOAD; + + /* setup the udc->eps[] for non-control endpoints and link + * to gadget.ep_list */ + for (i = 1; i < (int)(udc_controller->max_ep / 2); i++) { + char name[14]; + + sprintf(name, "ep%dout", i); + struct_ep_setup(udc_controller, i * 2, name, 1); + sprintf(name, "ep%din", i); + struct_ep_setup(udc_controller, i * 2 + 1, name, 1); + } + + /* use dma_pool for TD management */ + udc_controller->td_pool = dma_pool_create("udc_td", &pdev->dev, + sizeof(struct ep_td_struct), + DTD_ALIGNMENT, UDC_DMA_BOUNDARY); + if (udc_controller->td_pool == NULL) { + ret = -ENOMEM; + goto err4; + } + create_proc_file(); + return 0; + +err4: + device_unregister(&udc_controller->gadget.dev); +err3: + free_irq(udc_controller->irq, udc_controller); +err2: + iounmap(dr_regs); +err1: + release_mem_region(res->start, res->end - res->start + 1); + return ret; +} + +/* Driver removal function + * Free resources and finish pending transactions + */ +static int __exit fsl_udc_remove(struct platform_device *pdev) +{ + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + DECLARE_COMPLETION(done); + + if (!udc_controller) + return -ENODEV; + udc_controller->done = &done; + + /* DR has been stopped in usb_gadget_unregister_driver() */ + remove_proc_file(); + + /* Free allocated memory */ + kfree(udc_controller->status_req->req.buf); + kfree(udc_controller->status_req); + kfree(udc_controller->eps); + + dma_pool_destroy(udc_controller->td_pool); + free_irq(udc_controller->irq, udc_controller); + iounmap(dr_regs); + release_mem_region(res->start, res->end - res->start + 1); + + device_unregister(&udc_controller->gadget.dev); + /* free udc --wait for the release() finished */ + wait_for_completion(&done); + + return 0; +} + +/*----------------------------------------------------------------- + * Modify Power management attributes + * Used by OTG statemachine to disable gadget temporarily + -----------------------------------------------------------------*/ +static int fsl_udc_suspend(struct platform_device *pdev, pm_message_t state) +{ + dr_controller_stop(udc_controller); + return 0; +} + +/*----------------------------------------------------------------- + * Invoked on USB resume. May be called in_interrupt. + * Here we start the DR controller and enable the irq + *-----------------------------------------------------------------*/ +static int fsl_udc_resume(struct platform_device *pdev) +{ + /* Enable DR irq reg and set controller Run */ + if (udc_controller->stopped) { + dr_controller_setup(udc_controller); + dr_controller_run(udc_controller); + } + udc_controller->usb_state = USB_STATE_ATTACHED; + udc_controller->ep0_state = WAIT_FOR_SETUP; + udc_controller->ep0_dir = 0; + return 0; +} + +/*------------------------------------------------------------------------- + Register entry point for the peripheral controller driver +--------------------------------------------------------------------------*/ + +static struct platform_driver udc_driver = { + .remove = __exit_p(fsl_udc_remove), + /* these suspend and resume are not usb suspend and resume */ + .suspend = fsl_udc_suspend, + .resume = fsl_udc_resume, + .driver = { + .name = (char *)driver_name, + .owner = THIS_MODULE, + }, +}; + +static int __init udc_init(void) +{ + printk(KERN_INFO "%s (%s)\n", driver_desc, DRIVER_VERSION); + return platform_driver_probe(&udc_driver, fsl_udc_probe); +} + +module_init(udc_init); + +static void __exit udc_exit(void) +{ + platform_driver_unregister(&udc_driver); + printk("%s unregistered \n", driver_desc); +} + +module_exit(udc_exit); + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/gadget/fsl_usb2_udc.h b/drivers/usb/gadget/fsl_usb2_udc.h new file mode 100644 index 0000000..c6291e0 --- /dev/null +++ b/drivers/usb/gadget/fsl_usb2_udc.h @@ -0,0 +1,579 @@ +/* + * Freescale USB device/endpoint management registers + */ +#ifndef __FSL_USB2_UDC_H +#define __FSL_USB2_UDC_H + +/* ### define USB registers here + */ +#define USB_MAX_CTRL_PAYLOAD 64 +#define USB_DR_SYS_OFFSET 0x400 + + /* USB DR device mode registers (Little Endian) */ +struct usb_dr_device { + /* Capability register */ + u8 res1[256]; + u16 caplength; /* Capability Register Length */ + u16 hciversion; /* Host Controller Interface Version */ + u32 hcsparams; /* Host Controller Structual Parameters */ + u32 hccparams; /* Host Controller Capability Parameters */ + u8 res2[20]; + u32 dciversion; /* Device Controller Interface Version */ + u32 dccparams; /* Device Controller Capability Parameters */ + u8 res3[24]; + /* Operation register */ + u32 usbcmd; /* USB Command Register */ + u32 usbsts; /* USB Status Register */ + u32 usbintr; /* USB Interrupt Enable Register */ + u32 frindex; /* Frame Index Register */ + u8 res4[4]; + u32 deviceaddr; /* Device Address */ + u32 endpointlistaddr; /* Endpoint List Address Register */ + u8 res5[4]; + u32 burstsize; /* Master Interface Data Burst Size Register */ + u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ + u8 res6[24]; + u32 configflag; /* Configure Flag Register */ + u32 portsc1; /* Port 1 Status and Control Register */ + u8 res7[28]; + u32 otgsc; /* On-The-Go Status and Control */ + u32 usbmode; /* USB Mode Register */ + u32 endptsetupstat; /* Endpoint Setup Status Register */ + u32 endpointprime; /* Endpoint Initialization Register */ + u32 endptflush; /* Endpoint Flush Register */ + u32 endptstatus; /* Endpoint Status Register */ + u32 endptcomplete; /* Endpoint Complete Register */ + u32 endptctrl[6]; /* Endpoint Control Registers */ +}; + + /* USB DR host mode registers (Little Endian) */ +struct usb_dr_host { + /* Capability register */ + u8 res1[256]; + u16 caplength; /* Capability Register Length */ + u16 hciversion; /* Host Controller Interface Version */ + u32 hcsparams; /* Host Controller Structual Parameters */ + u32 hccparams; /* Host Controller Capability Parameters */ + u8 res2[20]; + u32 dciversion; /* Device Controller Interface Version */ + u32 dccparams; /* Device Controller Capability Parameters */ + u8 res3[24]; + /* Operation register */ + u32 usbcmd; /* USB Command Register */ + u32 usbsts; /* USB Status Register */ + u32 usbintr; /* USB Interrupt Enable Register */ + u32 frindex; /* Frame Index Register */ + u8 res4[4]; + u32 periodiclistbase; /* Periodic Frame List Base Address Register */ + u32 asynclistaddr; /* Current Asynchronous List Address Register */ + u8 res5[4]; + u32 burstsize; /* Master Interface Data Burst Size Register */ + u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ + u8 res6[24]; + u32 configflag; /* Configure Flag Register */ + u32 portsc1; /* Port 1 Status and Control Register */ + u8 res7[28]; + u32 otgsc; /* On-The-Go Status and Control */ + u32 usbmode; /* USB Mode Register */ + u32 endptsetupstat; /* Endpoint Setup Status Register */ + u32 endpointprime; /* Endpoint Initialization Register */ + u32 endptflush; /* Endpoint Flush Register */ + u32 endptstatus; /* Endpoint Status Register */ + u32 endptcomplete; /* Endpoint Complete Register */ + u32 endptctrl[6]; /* Endpoint Control Registers */ +}; + + /* non-EHCI USB system interface registers (Big Endian) */ +struct usb_sys_interface { + u32 snoop1; + u32 snoop2; + u32 age_cnt_thresh; /* Age Count Threshold Register */ + u32 pri_ctrl; /* Priority Control Register */ + u32 si_ctrl; /* System Interface Control Register */ + u8 res[236]; + u32 control; /* General Purpose Control Register */ +}; + +/* ep0 transfer state */ +#define WAIT_FOR_SETUP 0 +#define DATA_STATE_XMIT 1 +#define DATA_STATE_NEED_ZLP 2 +#define WAIT_FOR_OUT_STATUS 3 +#define DATA_STATE_RECV 4 + +/* Frame Index Register Bit Masks */ +#define USB_FRINDEX_MASKS 0x3fff +/* USB CMD Register Bit Masks */ +#define USB_CMD_RUN_STOP 0x00000001 +#define USB_CMD_CTRL_RESET 0x00000002 +#define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010 +#define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020 +#define USB_CMD_INT_AA_DOORBELL 0x00000040 +#define USB_CMD_ASP 0x00000300 +#define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800 +#define USB_CMD_SUTW 0x00002000 +#define USB_CMD_ATDTW 0x00004000 +#define USB_CMD_ITC 0x00FF0000 + +/* bit 15,3,2 are frame list size */ +#define USB_CMD_FRAME_SIZE_1024 0x00000000 +#define USB_CMD_FRAME_SIZE_512 0x00000004 +#define USB_CMD_FRAME_SIZE_256 0x00000008 +#define USB_CMD_FRAME_SIZE_128 0x0000000C +#define USB_CMD_FRAME_SIZE_64 0x00008000 +#define USB_CMD_FRAME_SIZE_32 0x00008004 +#define USB_CMD_FRAME_SIZE_16 0x00008008 +#define USB_CMD_FRAME_SIZE_8 0x0000800C + +/* bit 9-8 are async schedule park mode count */ +#define USB_CMD_ASP_00 0x00000000 +#define USB_CMD_ASP_01 0x00000100 +#define USB_CMD_ASP_10 0x00000200 +#define USB_CMD_ASP_11 0x00000300 +#define USB_CMD_ASP_BIT_POS 8 + +/* bit 23-16 are interrupt threshold control */ +#define USB_CMD_ITC_NO_THRESHOLD 0x00000000 +#define USB_CMD_ITC_1_MICRO_FRM 0x00010000 +#define USB_CMD_ITC_2_MICRO_FRM 0x00020000 +#define USB_CMD_ITC_4_MICRO_FRM 0x00040000 +#define USB_CMD_ITC_8_MICRO_FRM 0x00080000 +#define USB_CMD_ITC_16_MICRO_FRM 0x00100000 +#define USB_CMD_ITC_32_MICRO_FRM 0x00200000 +#define USB_CMD_ITC_64_MICRO_FRM 0x00400000 +#define USB_CMD_ITC_BIT_POS 16 + +/* USB STS Register Bit Masks */ +#define USB_STS_INT 0x00000001 +#define USB_STS_ERR 0x00000002 +#define USB_STS_PORT_CHANGE 0x00000004 +#define USB_STS_FRM_LST_ROLL 0x00000008 +#define USB_STS_SYS_ERR 0x00000010 +#define USB_STS_IAA 0x00000020 +#define USB_STS_RESET 0x00000040 +#define USB_STS_SOF 0x00000080 +#define USB_STS_SUSPEND 0x00000100 +#define USB_STS_HC_HALTED 0x00001000 +#define USB_STS_RCL 0x00002000 +#define USB_STS_PERIODIC_SCHEDULE 0x00004000 +#define USB_STS_ASYNC_SCHEDULE 0x00008000 + +/* USB INTR Register Bit Masks */ +#define USB_INTR_INT_EN 0x00000001 +#define USB_INTR_ERR_INT_EN 0x00000002 +#define USB_INTR_PTC_DETECT_EN 0x00000004 +#define USB_INTR_FRM_LST_ROLL_EN 0x00000008 +#define USB_INTR_SYS_ERR_EN 0x00000010 +#define USB_INTR_ASYN_ADV_EN 0x00000020 +#define USB_INTR_RESET_EN 0x00000040 +#define USB_INTR_SOF_EN 0x00000080 +#define USB_INTR_DEVICE_SUSPEND 0x00000100 + +/* Device Address bit masks */ +#define USB_DEVICE_ADDRESS_MASK 0xFE000000 +#define USB_DEVICE_ADDRESS_BIT_POS 25 + +/* endpoint list address bit masks */ +#define USB_EP_LIST_ADDRESS_MASK 0xfffff800 + +/* PORTSCX Register Bit Masks */ +#define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001 +#define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002 +#define PORTSCX_PORT_ENABLE 0x00000004 +#define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008 +#define PORTSCX_OVER_CURRENT_ACT 0x00000010 +#define PORTSCX_OVER_CURRENT_CHG 0x00000020 +#define PORTSCX_PORT_FORCE_RESUME 0x00000040 +#define PORTSCX_PORT_SUSPEND 0x00000080 +#define PORTSCX_PORT_RESET 0x00000100 +#define PORTSCX_LINE_STATUS_BITS 0x00000C00 +#define PORTSCX_PORT_POWER 0x00001000 +#define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000 +#define PORTSCX_PORT_TEST_CTRL 0x000F0000 +#define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000 +#define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000 +#define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000 +#define PORTSCX_PHY_LOW_POWER_SPD 0x00800000 +#define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000 +#define PORTSCX_PORT_SPEED_MASK 0x0C000000 +#define PORTSCX_PORT_WIDTH 0x10000000 +#define PORTSCX_PHY_TYPE_SEL 0xC0000000 + +/* bit 11-10 are line status */ +#define PORTSCX_LINE_STATUS_SE0 0x00000000 +#define PORTSCX_LINE_STATUS_JSTATE 0x00000400 +#define PORTSCX_LINE_STATUS_KSTATE 0x00000800 +#define PORTSCX_LINE_STATUS_UNDEF 0x00000C00 +#define PORTSCX_LINE_STATUS_BIT_POS 10 + +/* bit 15-14 are port indicator control */ +#define PORTSCX_PIC_OFF 0x00000000 +#define PORTSCX_PIC_AMBER 0x00004000 +#define PORTSCX_PIC_GREEN 0x00008000 +#define PORTSCX_PIC_UNDEF 0x0000C000 +#define PORTSCX_PIC_BIT_POS 14 + +/* bit 19-16 are port test control */ +#define PORTSCX_PTC_DISABLE 0x00000000 +#define PORTSCX_PTC_JSTATE 0x00010000 +#define PORTSCX_PTC_KSTATE 0x00020000 +#define PORTSCX_PTC_SEQNAK 0x00030000 +#define PORTSCX_PTC_PACKET 0x00040000 +#define PORTSCX_PTC_FORCE_EN 0x00050000 +#define PORTSCX_PTC_BIT_POS 16 + +/* bit 27-26 are port speed */ +#define PORTSCX_PORT_SPEED_FULL 0x00000000 +#define PORTSCX_PORT_SPEED_LOW 0x04000000 +#define PORTSCX_PORT_SPEED_HIGH 0x08000000 +#define PORTSCX_PORT_SPEED_UNDEF 0x0C000000 +#define PORTSCX_SPEED_BIT_POS 26 + +/* bit 28 is parallel transceiver width for UTMI interface */ +#define PORTSCX_PTW 0x10000000 +#define PORTSCX_PTW_8BIT 0x00000000 +#define PORTSCX_PTW_16BIT 0x10000000 + +/* bit 31-30 are port transceiver select */ +#define PORTSCX_PTS_UTMI 0x00000000 +#define PORTSCX_PTS_ULPI 0x80000000 +#define PORTSCX_PTS_FSLS 0xC0000000 +#define PORTSCX_PTS_BIT_POS 30 + +/* otgsc Register Bit Masks */ +#define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001 +#define OTGSC_CTRL_VUSB_CHARGE 0x00000002 +#define OTGSC_CTRL_OTG_TERM 0x00000008 +#define OTGSC_CTRL_DATA_PULSING 0x00000010 +#define OTGSC_STS_USB_ID 0x00000100 +#define OTGSC_STS_A_VBUS_VALID 0x00000200 +#define OTGSC_STS_A_SESSION_VALID 0x00000400 +#define OTGSC_STS_B_SESSION_VALID 0x00000800 +#define OTGSC_STS_B_SESSION_END 0x00001000 +#define OTGSC_STS_1MS_TOGGLE 0x00002000 +#define OTGSC_STS_DATA_PULSING 0x00004000 +#define OTGSC_INTSTS_USB_ID 0x00010000 +#define OTGSC_INTSTS_A_VBUS_VALID 0x00020000 +#define OTGSC_INTSTS_A_SESSION_VALID 0x00040000 +#define OTGSC_INTSTS_B_SESSION_VALID 0x00080000 +#define OTGSC_INTSTS_B_SESSION_END 0x00100000 +#define OTGSC_INTSTS_1MS 0x00200000 +#define OTGSC_INTSTS_DATA_PULSING 0x00400000 +#define OTGSC_INTR_USB_ID 0x01000000 +#define OTGSC_INTR_A_VBUS_VALID 0x02000000 +#define OTGSC_INTR_A_SESSION_VALID 0x04000000 +#define OTGSC_INTR_B_SESSION_VALID 0x08000000 +#define OTGSC_INTR_B_SESSION_END 0x10000000 +#define OTGSC_INTR_1MS_TIMER 0x20000000 +#define OTGSC_INTR_DATA_PULSING 0x40000000 + +/* USB MODE Register Bit Masks */ +#define USB_MODE_CTRL_MODE_IDLE 0x00000000 +#define USB_MODE_CTRL_MODE_DEVICE 0x00000002 +#define USB_MODE_CTRL_MODE_HOST 0x00000003 +#define USB_MODE_CTRL_MODE_RSV 0x00000001 +#define USB_MODE_SETUP_LOCK_OFF 0x00000008 +#define USB_MODE_STREAM_DISABLE 0x00000010 +/* Endpoint Flush Register */ +#define EPFLUSH_TX_OFFSET 0x00010000 +#define EPFLUSH_RX_OFFSET 0x00000000 + +/* Endpoint Setup Status bit masks */ +#define EP_SETUP_STATUS_MASK 0x0000003F +#define EP_SETUP_STATUS_EP0 0x00000001 + +/* ENDPOINTCTRLx Register Bit Masks */ +#define EPCTRL_TX_ENABLE 0x00800000 +#define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */ +#define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */ +#define EPCTRL_TX_TYPE 0x000C0000 +#define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */ +#define EPCTRL_TX_EP_STALL 0x00010000 +#define EPCTRL_RX_ENABLE 0x00000080 +#define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */ +#define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */ +#define EPCTRL_RX_TYPE 0x0000000C +#define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */ +#define EPCTRL_RX_EP_STALL 0x00000001 + +/* bit 19-18 and 3-2 are endpoint type */ +#define EPCTRL_EP_TYPE_CONTROL 0 +#define EPCTRL_EP_TYPE_ISO 1 +#define EPCTRL_EP_TYPE_BULK 2 +#define EPCTRL_EP_TYPE_INTERRUPT 3 +#define EPCTRL_TX_EP_TYPE_SHIFT 18 +#define EPCTRL_RX_EP_TYPE_SHIFT 2 + +/* SNOOPn Register Bit Masks */ +#define SNOOP_ADDRESS_MASK 0xFFFFF000 +#define SNOOP_SIZE_ZERO 0x00 /* snooping disable */ +#define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */ +#define SNOOP_SIZE_8KB 0x0C +#define SNOOP_SIZE_16KB 0x0D +#define SNOOP_SIZE_32KB 0x0E +#define SNOOP_SIZE_64KB 0x0F +#define SNOOP_SIZE_128KB 0x10 +#define SNOOP_SIZE_256KB 0x11 +#define SNOOP_SIZE_512KB 0x12 +#define SNOOP_SIZE_1MB 0x13 +#define SNOOP_SIZE_2MB 0x14 +#define SNOOP_SIZE_4MB 0x15 +#define SNOOP_SIZE_8MB 0x16 +#define SNOOP_SIZE_16MB 0x17 +#define SNOOP_SIZE_32MB 0x18 +#define SNOOP_SIZE_64MB 0x19 +#define SNOOP_SIZE_128MB 0x1A +#define SNOOP_SIZE_256MB 0x1B +#define SNOOP_SIZE_512MB 0x1C +#define SNOOP_SIZE_1GB 0x1D +#define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */ + +/* pri_ctrl Register Bit Masks */ +#define PRI_CTRL_PRI_LVL1 0x0000000C +#define PRI_CTRL_PRI_LVL0 0x00000003 + +/* si_ctrl Register Bit Masks */ +#define SI_CTRL_ERR_DISABLE 0x00000010 +#define SI_CTRL_IDRC_DISABLE 0x00000008 +#define SI_CTRL_RD_SAFE_EN 0x00000004 +#define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002 +#define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001 + +/* control Register Bit Masks */ +#define USB_CTRL_IOENB 0x00000004 +#define USB_CTRL_ULPI_INT0EN 0x00000001 + +/* Endpoint Queue Head data struct + * Rem: all the variables of qh are LittleEndian Mode + * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr + */ +struct ep_queue_head { + u32 max_pkt_length; /* Mult(31-30) , Zlt(29) , Max Pkt len + and IOS(15) */ + u32 curr_dtd_ptr; /* Current dTD Pointer(31-5) */ + u32 next_dtd_ptr; /* Next dTD Pointer(31-5), T(0) */ + u32 size_ioc_int_sts; /* Total bytes (30-16), IOC (15), + MultO(11-10), STS (7-0) */ + u32 buff_ptr0; /* Buffer pointer Page 0 (31-12) */ + u32 buff_ptr1; /* Buffer pointer Page 1 (31-12) */ + u32 buff_ptr2; /* Buffer pointer Page 2 (31-12) */ + u32 buff_ptr3; /* Buffer pointer Page 3 (31-12) */ + u32 buff_ptr4; /* Buffer pointer Page 4 (31-12) */ + u32 res1; + u8 setup_buffer[8]; /* Setup data 8 bytes */ + u32 res2[4]; +}; + +/* Endpoint Queue Head Bit Masks */ +#define EP_QUEUE_HEAD_MULT_POS 30 +#define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 +#define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 +#define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) +#define EP_QUEUE_HEAD_IOS 0x00008000 +#define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 +#define EP_QUEUE_HEAD_IOC 0x00008000 +#define EP_QUEUE_HEAD_MULTO 0x00000C00 +#define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 +#define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 +#define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF +#define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 +#define EP_QUEUE_FRINDEX_MASK 0x000007FF +#define EP_MAX_LENGTH_TRANSFER 0x4000 + +/* Endpoint Transfer Descriptor data struct */ +/* Rem: all the variables of td are LittleEndian Mode */ +struct ep_td_struct { + u32 next_td_ptr; /* Next TD pointer(31-5), T(0) set + indicate invalid */ + u32 size_ioc_sts; /* Total bytes (30-16), IOC (15), + MultO(11-10), STS (7-0) */ + u32 buff_ptr0; /* Buffer pointer Page 0 */ + u32 buff_ptr1; /* Buffer pointer Page 1 */ + u32 buff_ptr2; /* Buffer pointer Page 2 */ + u32 buff_ptr3; /* Buffer pointer Page 3 */ + u32 buff_ptr4; /* Buffer pointer Page 4 */ + u32 res; + /* 32 bytes */ + dma_addr_t td_dma; /* dma address for this td */ + /* virtual address of next td specified in next_td_ptr */ + struct ep_td_struct *next_td_virt; +}; + +/* Endpoint Transfer Descriptor bit Masks */ +#define DTD_NEXT_TERMINATE 0x00000001 +#define DTD_IOC 0x00008000 +#define DTD_STATUS_ACTIVE 0x00000080 +#define DTD_STATUS_HALTED 0x00000040 +#define DTD_STATUS_DATA_BUFF_ERR 0x00000020 +#define DTD_STATUS_TRANSACTION_ERR 0x00000008 +#define DTD_RESERVED_FIELDS 0x80007300 +#define DTD_ADDR_MASK 0xFFFFFFE0 +#define DTD_PACKET_SIZE 0x7FFF0000 +#define DTD_LENGTH_BIT_POS 16 +#define DTD_ERROR_MASK (DTD_STATUS_HALTED | \ + DTD_STATUS_DATA_BUFF_ERR | \ + DTD_STATUS_TRANSACTION_ERR) +/* Alignment requirements; must be a power of two */ +#define DTD_ALIGNMENT 0x20 +#define QH_ALIGNMENT 2048 + +/* Controller dma boundary */ +#define UDC_DMA_BOUNDARY 0x1000 + +/* -----------------------------------------------------------------------*/ +/* ##### enum data +*/ +typedef enum { + e_ULPI, + e_UTMI_8BIT, + e_UTMI_16BIT, + e_SERIAL +} e_PhyInterface; + +/*-------------------------------------------------------------------------*/ + +/* ### driver private data + */ +struct fsl_req { + struct usb_request req; + struct list_head queue; + /* ep_queue() func will add + a request->queue into a udc_ep->queue 'd tail */ + struct fsl_ep *ep; + unsigned mapped:1; + + struct ep_td_struct *head, *tail; /* For dTD List + cpu endian Virtual addr */ + unsigned int dtd_count; +}; + +#define REQ_UNCOMPLETE 1 + +struct fsl_ep { + struct usb_ep ep; + struct list_head queue; + struct fsl_udc *udc; + struct ep_queue_head *qh; + const struct usb_endpoint_descriptor *desc; + struct usb_gadget *gadget; + + char name[14]; + unsigned stopped:1; +}; + +#define EP_DIR_IN 1 +#define EP_DIR_OUT 0 + +struct fsl_udc { + + struct usb_gadget gadget; + struct usb_gadget_driver *driver; + struct fsl_ep *eps; + unsigned int max_ep; + unsigned int irq; + + struct usb_ctrlrequest local_setup_buff; + spinlock_t lock; + struct otg_transceiver *transceiver; + unsigned softconnect:1; + unsigned vbus_active:1; + unsigned stopped:1; + unsigned remote_wakeup:1; + + struct ep_queue_head *ep_qh; /* Endpoints Queue-Head */ + struct fsl_req *status_req; /* ep0 status request */ + struct dma_pool *td_pool; /* dma pool for DTD */ + enum fsl_usb2_phy_modes phy_mode; + + size_t ep_qh_size; /* size after alignment adjustment*/ + dma_addr_t ep_qh_dma; /* dma address of QH */ + + u32 max_pipes; /* Device max pipes */ + u32 max_use_endpts; /* Max endpointes to be used */ + u32 bus_reset; /* Device is bus reseting */ + u32 resume_state; /* USB state to resume */ + u32 usb_state; /* USB current state */ + u32 usb_next_state; /* USB next state */ + u32 ep0_state; /* Endpoint zero state */ + u32 ep0_dir; /* Endpoint zero direction: can be + USB_DIR_IN or USB_DIR_OUT */ + u32 usb_sof_count; /* SOF count */ + u32 errors; /* USB ERRORs count */ + u8 device_address; /* Device USB address */ + + struct completion *done; /* to make sure release() is done */ +}; + +/*-------------------------------------------------------------------------*/ + +#ifdef DEBUG +#define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \ + __FUNCTION__, ## args) +#else +#define DBG(fmt, args...) do{}while(0) +#endif + +#if 0 +static void dump_msg(const char *label, const u8 * buf, unsigned int length) +{ + unsigned int start, num, i; + char line[52], *p; + + if (length >= 512) + return; + DBG("%s, length %u:\n", label, length); + start = 0; + while (length > 0) { + num = min(length, 16u); + p = line; + for (i = 0; i < num; ++i) { + if (i == 8) + *p++ = ' '; + sprintf(p, " %02x", buf[i]); + p += 3; + } + *p = 0; + printk(KERN_DEBUG "%6x: %s\n", start, line); + buf += num; + start += num; + length -= num; + } +} +#endif + +#ifdef VERBOSE +#define VDBG DBG +#else +#define VDBG(stuff...) do{}while(0) +#endif + +#define ERR(stuff...) printk(KERN_ERR "udc: " stuff) +#define WARN(stuff...) printk(KERN_WARNING "udc: " stuff) +#define INFO(stuff...) printk(KERN_INFO "udc: " stuff) + +/*-------------------------------------------------------------------------*/ + +/* ### Add board specific defines here + */ + +/* + * ### pipe direction macro from device view + */ +#define USB_RECV 0 /* OUT EP */ +#define USB_SEND 1 /* IN EP */ + +/* + * ### internal used help routines. + */ +#define ep_index(EP) ((EP)->desc->bEndpointAddress&0xF) +#define ep_maxpacket(EP) ((EP)->ep.maxpacket) +#define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \ + USB_DIR_IN ):((EP)->desc->bEndpointAddress \ + & USB_DIR_IN)==USB_DIR_IN) +#define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \ + &udc->eps[pipe]) +#define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \ + * 2 + ((windex & USB_DIR_IN) ? 1 : 0)) +#define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP)) + +#endif |