diff options
Diffstat (limited to 'Documentation/networking/README.ipw2200')
| -rw-r--r-- | Documentation/networking/README.ipw2200 | 300 |
1 files changed, 300 insertions, 0 deletions
diff --git a/Documentation/networking/README.ipw2200 b/Documentation/networking/README.ipw2200 new file mode 100644 index 0000000..6916080 --- /dev/null +++ b/Documentation/networking/README.ipw2200 @@ -0,0 +1,300 @@ + +Intel(R) PRO/Wireless 2915ABG Driver for Linux in support of: + +Intel(R) PRO/Wireless 2200BG Network Connection +Intel(R) PRO/Wireless 2915ABG Network Connection + +Note: The Intel(R) PRO/Wireless 2915ABG Driver for Linux and Intel(R) +PRO/Wireless 2200BG Driver for Linux is a unified driver that works on +both hardware adapters listed above. In this document the Intel(R) +PRO/Wireless 2915ABG Driver for Linux will be used to reference the +unified driver. + +Copyright (C) 2004-2005, Intel Corporation + +README.ipw2200 + +Version: 1.0.0 +Date : January 31, 2005 + + +Index +----------------------------------------------- +1. Introduction +1.1. Overview of features +1.2. Module parameters +1.3. Wireless Extension Private Methods +1.4. Sysfs Helper Files +2. About the Version Numbers +3. Support +4. License + + +1. Introduction +----------------------------------------------- +The following sections attempt to provide a brief introduction to using +the Intel(R) PRO/Wireless 2915ABG Driver for Linux. + +This document is not meant to be a comprehensive manual on +understanding or using wireless technologies, but should be sufficient +to get you moving without wires on Linux. + +For information on building and installing the driver, see the INSTALL +file. + + +1.1. Overview of Features +----------------------------------------------- +The current release (1.0.0) supports the following features: + ++ BSS mode (Infrastructure, Managed) ++ IBSS mode (Ad-Hoc) ++ WEP (OPEN and SHARED KEY mode) ++ 802.1x EAP via wpa_supplicant and xsupplicant ++ Wireless Extension support ++ Full B and G rate support (2200 and 2915) ++ Full A rate support (2915 only) ++ Transmit power control ++ S state support (ACPI suspend/resume) ++ long/short preamble support + + + +1.2. Command Line Parameters +----------------------------------------------- + +Like many modules used in the Linux kernel, the Intel(R) PRO/Wireless +2915ABG Driver for Linux allows certain configuration options to be +provided as module parameters. The most common way to specify a module +parameter is via the command line. + +The general form is: + +% modprobe ipw2200 parameter=value + +Where the supported parameter are: + + associate + Set to 0 to disable the auto scan-and-associate functionality of the + driver. If disabled, the driver will not attempt to scan + for and associate to a network until it has been configured with + one or more properties for the target network, for example configuring + the network SSID. Default is 1 (auto-associate) + + Example: % modprobe ipw2200 associate=0 + + auto_create + Set to 0 to disable the auto creation of an Ad-Hoc network + matching the channel and network name parameters provided. + Default is 1. + + channel + channel number for association. The normal method for setting + the channel would be to use the standard wireless tools + (i.e. `iwconfig eth1 channel 10`), but it is useful sometimes + to set this while debugging. Channel 0 means 'ANY' + + debug + If using a debug build, this is used to control the amount of debug + info is logged. See the 'dval' and 'load' script for more info on + how to use this (the dval and load scripts are provided as part + of the ipw2200 development snapshot releases available from the + SourceForge project at http://ipw2200.sf.net) + + mode + Can be used to set the default mode of the adapter. + 0 = Managed, 1 = Ad-Hoc + + +1.3. Wireless Extension Private Methods +----------------------------------------------- + +As an interface designed to handle generic hardware, there are certain +capabilities not exposed through the normal Wireless Tool interface. As +such, a provision is provided for a driver to declare custom, or +private, methods. The Intel(R) PRO/Wireless 2915ABG Driver for Linux +defines several of these to configure various settings. + +The general form of using the private wireless methods is: + + % iwpriv $IFNAME method parameters + +Where $IFNAME is the interface name the device is registered with +(typically eth1, customized via one of the various network interface +name managers, such as ifrename) + +The supported private methods are: + + get_mode + Can be used to report out which IEEE mode the driver is + configured to support. Example: + + % iwpriv eth1 get_mode + eth1 get_mode:802.11bg (6) + + set_mode + Can be used to configure which IEEE mode the driver will + support. + + Usage: + % iwpriv eth1 set_mode {mode} + Where {mode} is a number in the range 1-7: + 1 802.11a (2915 only) + 2 802.11b + 3 802.11ab (2915 only) + 4 802.11g + 5 802.11ag (2915 only) + 6 802.11bg + 7 802.11abg (2915 only) + + get_preamble + Can be used to report configuration of preamble length. + + set_preamble + Can be used to set the configuration of preamble length: + + Usage: + % iwpriv eth1 set_preamble {mode} + Where {mode} is one of: + 1 Long preamble only + 0 Auto (long or short based on connection) + + +1.4. Sysfs Helper Files: +----------------------------------------------- + +The Linux kernel provides a pseudo file system that can be used to +access various components of the operating system. The Intel(R) +PRO/Wireless 2915ABG Driver for Linux exposes several configuration +parameters through this mechanism. + +An entry in the sysfs can support reading and/or writing. You can +typically query the contents of a sysfs entry through the use of cat, +and can set the contents via echo. For example: + +% cat /sys/bus/pci/drivers/ipw2200/debug_level + +Will report the current debug level of the driver's logging subsystem +(only available if CONFIG_IPW_DEBUG was configured when the driver was +built). + +You can set the debug level via: + +% echo $VALUE > /sys/bus/pci/drivers/ipw2200/debug_level + +Where $VALUE would be a number in the case of this sysfs entry. The +input to sysfs files does not have to be a number. For example, the +firmware loader used by hotplug utilizes sysfs entries for transferring +the firmware image from user space into the driver. + +The Intel(R) PRO/Wireless 2915ABG Driver for Linux exposes sysfs entries +at two levels -- driver level, which apply to all instances of the +driver (in the event that there are more than one device installed) and +device level, which applies only to the single specific instance. + + +1.4.1 Driver Level Sysfs Helper Files +----------------------------------------------- + +For the driver level files, look in /sys/bus/pci/drivers/ipw2200/ + + debug_level + + This controls the same global as the 'debug' module parameter + + +1.4.2 Device Level Sysfs Helper Files +----------------------------------------------- + +For the device level files, look in + + /sys/bus/pci/drivers/ipw2200/{PCI-ID}/ + +For example: + /sys/bus/pci/drivers/ipw2200/0000:02:01.0 + +For the device level files, see /sys/bus/pci/[drivers/ipw2200: + + rf_kill + read - + 0 = RF kill not enabled (radio on) + 1 = SW based RF kill active (radio off) + 2 = HW based RF kill active (radio off) + 3 = Both HW and SW RF kill active (radio off) + write - + 0 = If SW based RF kill active, turn the radio back on + 1 = If radio is on, activate SW based RF kill + + NOTE: If you enable the SW based RF kill and then toggle the HW + based RF kill from ON -> OFF -> ON, the radio will NOT come back on + + ucode + read-only access to the ucode version number + + +2. About the Version Numbers +----------------------------------------------- + +Due to the nature of open source development projects, there are +frequently changes being incorporated that have not gone through +a complete validation process. These changes are incorporated into +development snapshot releases. + +Releases are numbered with a three level scheme: + + major.minor.development + +Any version where the 'development' portion is 0 (for example +1.0.0, 1.1.0, etc.) indicates a stable version that will be made +available for kernel inclusion. + +Any version where the 'development' portion is not a 0 (for +example 1.0.1, 1.1.5, etc.) indicates a development version that is +being made available for testing and cutting edge users. The stability +and functionality of the development releases are not know. We make +efforts to try and keep all snapshots reasonably stable, but due to the +frequency of their release, and the desire to get those releases +available as quickly as possible, unknown anomalies should be expected. + +The major version number will be incremented when significant changes +are made to the driver. Currently, there are no major changes planned. + + +3. Support +----------------------------------------------- + +For installation support of the 1.0.0 version, you can contact +http://supportmail.intel.com, or you can use the open source project +support. + +For general information and support, go to: + + http://ipw2200.sf.net/ + + +4. License +----------------------------------------------- + + Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of the GNU General Public License version 2 as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + + |