diff options
Diffstat (limited to 'Documentation/vm/numa_memory_policy.txt')
-rw-r--r-- | Documentation/vm/numa_memory_policy.txt | 131 |
1 files changed, 100 insertions, 31 deletions
diff --git a/Documentation/vm/numa_memory_policy.txt b/Documentation/vm/numa_memory_policy.txt index 1278e68..706410d 100644 --- a/Documentation/vm/numa_memory_policy.txt +++ b/Documentation/vm/numa_memory_policy.txt @@ -135,9 +135,11 @@ most general to most specific: Components of Memory Policies - A Linux memory policy is a tuple consisting of a "mode" and an optional set - of nodes. The mode determine the behavior of the policy, while the - optional set of nodes can be viewed as the arguments to the behavior. + A Linux memory policy consists of a "mode", optional mode flags, and an + optional set of nodes. The mode determines the behavior of the policy, + the optional mode flags determine the behavior of the mode, and the + optional set of nodes can be viewed as the arguments to the policy + behavior. Internally, memory policies are implemented by a reference counted structure, struct mempolicy. Details of this structure will be discussed @@ -179,7 +181,8 @@ Components of Memory Policies on a non-shared region of the address space. However, see MPOL_PREFERRED below. - The Default mode does not use the optional set of nodes. + It is an error for the set of nodes specified for this policy to + be non-empty. MPOL_BIND: This mode specifies that memory must come from the set of nodes specified by the policy. Memory will be allocated from @@ -226,6 +229,80 @@ Components of Memory Policies the temporary interleaved system default policy works in this mode. + Linux memory policy supports the following optional mode flags: + + MPOL_F_STATIC_NODES: This flag specifies that the nodemask passed by + the user should not be remapped if the task or VMA's set of allowed + nodes changes after the memory policy has been defined. + + Without this flag, anytime a mempolicy is rebound because of a + change in the set of allowed nodes, the node (Preferred) or + nodemask (Bind, Interleave) is remapped to the new set of + allowed nodes. This may result in nodes being used that were + previously undesired. + + With this flag, if the user-specified nodes overlap with the + nodes allowed by the task's cpuset, then the memory policy is + applied to their intersection. If the two sets of nodes do not + overlap, the Default policy is used. + + For example, consider a task that is attached to a cpuset with + mems 1-3 that sets an Interleave policy over the same set. If + the cpuset's mems change to 3-5, the Interleave will now occur + over nodes 3, 4, and 5. With this flag, however, since only node + 3 is allowed from the user's nodemask, the "interleave" only + occurs over that node. If no nodes from the user's nodemask are + now allowed, the Default behavior is used. + + MPOL_F_STATIC_NODES cannot be used with MPOL_F_RELATIVE_NODES. + + MPOL_F_RELATIVE_NODES: This flag specifies that the nodemask passed + by the user will be mapped relative to the set of the task or VMA's + set of allowed nodes. The kernel stores the user-passed nodemask, + and if the allowed nodes changes, then that original nodemask will + be remapped relative to the new set of allowed nodes. + + Without this flag (and without MPOL_F_STATIC_NODES), anytime a + mempolicy is rebound because of a change in the set of allowed + nodes, the node (Preferred) or nodemask (Bind, Interleave) is + remapped to the new set of allowed nodes. That remap may not + preserve the relative nature of the user's passed nodemask to its + set of allowed nodes upon successive rebinds: a nodemask of + 1,3,5 may be remapped to 7-9 and then to 1-3 if the set of + allowed nodes is restored to its original state. + + With this flag, the remap is done so that the node numbers from + the user's passed nodemask are relative to the set of allowed + nodes. In other words, if nodes 0, 2, and 4 are set in the user's + nodemask, the policy will be effected over the first (and in the + Bind or Interleave case, the third and fifth) nodes in the set of + allowed nodes. The nodemask passed by the user represents nodes + relative to task or VMA's set of allowed nodes. + + If the user's nodemask includes nodes that are outside the range + of the new set of allowed nodes (for example, node 5 is set in + the user's nodemask when the set of allowed nodes is only 0-3), + then the remap wraps around to the beginning of the nodemask and, + if not already set, sets the node in the mempolicy nodemask. + + For example, consider a task that is attached to a cpuset with + mems 2-5 that sets an Interleave policy over the same set with + MPOL_F_RELATIVE_NODES. If the cpuset's mems change to 3-7, the + interleave now occurs over nodes 3,5-6. If the cpuset's mems + then change to 0,2-3,5, then the interleave occurs over nodes + 0,3,5. + + Thanks to the consistent remapping, applications preparing + nodemasks to specify memory policies using this flag should + disregard their current, actual cpuset imposed memory placement + and prepare the nodemask as if they were always located on + memory nodes 0 to N-1, where N is the number of memory nodes the + policy is intended to manage. Let the kernel then remap to the + set of memory nodes allowed by the task's cpuset, as that may + change over time. + + MPOL_F_RELATIVE_NODES cannot be used with MPOL_F_STATIC_NODES. + MEMORY POLICY APIs Linux supports 3 system calls for controlling memory policy. These APIS @@ -246,7 +323,9 @@ Set [Task] Memory Policy: Set's the calling task's "task/process memory policy" to mode specified by the 'mode' argument and the set of nodes defined by 'nmask'. 'nmask' points to a bit mask of node ids containing - at least 'maxnode' ids. + at least 'maxnode' ids. Optional mode flags may be passed by + combining the 'mode' argument with the flag (for example: + MPOL_INTERLEAVE | MPOL_F_STATIC_NODES). See the set_mempolicy(2) man page for more details @@ -298,29 +377,19 @@ MEMORY POLICIES AND CPUSETS Memory policies work within cpusets as described above. For memory policies that require a node or set of nodes, the nodes are restricted to the set of nodes whose memories are allowed by the cpuset constraints. If the nodemask -specified for the policy contains nodes that are not allowed by the cpuset, or -the intersection of the set of nodes specified for the policy and the set of -nodes with memory is the empty set, the policy is considered invalid -and cannot be installed. - -The interaction of memory policies and cpusets can be problematic for a -couple of reasons: - -1) the memory policy APIs take physical node id's as arguments. As mentioned - above, it is illegal to specify nodes that are not allowed in the cpuset. - The application must query the allowed nodes using the get_mempolicy() - API with the MPOL_F_MEMS_ALLOWED flag to determine the allowed nodes and - restrict itself to those nodes. However, the resources available to a - cpuset can be changed by the system administrator, or a workload manager - application, at any time. So, a task may still get errors attempting to - specify policy nodes, and must query the allowed memories again. - -2) when tasks in two cpusets share access to a memory region, such as shared - memory segments created by shmget() of mmap() with the MAP_ANONYMOUS and - MAP_SHARED flags, and any of the tasks install shared policy on the region, - only nodes whose memories are allowed in both cpusets may be used in the - policies. Obtaining this information requires "stepping outside" the - memory policy APIs to use the cpuset information and requires that one - know in what cpusets other task might be attaching to the shared region. - Furthermore, if the cpusets' allowed memory sets are disjoint, "local" - allocation is the only valid policy. +specified for the policy contains nodes that are not allowed by the cpuset and +MPOL_F_RELATIVE_NODES is not used, the intersection of the set of nodes +specified for the policy and the set of nodes with memory is used. If the +result is the empty set, the policy is considered invalid and cannot be +installed. If MPOL_F_RELATIVE_NODES is used, the policy's nodes are mapped +onto and folded into the task's set of allowed nodes as previously described. + +The interaction of memory policies and cpusets can be problematic when tasks +in two cpusets share access to a memory region, such as shared memory segments +created by shmget() of mmap() with the MAP_ANONYMOUS and MAP_SHARED flags, and +any of the tasks install shared policy on the region, only nodes whose +memories are allowed in both cpusets may be used in the policies. Obtaining +this information requires "stepping outside" the memory policy APIs to use the +cpuset information and requires that one know in what cpusets other task might +be attaching to the shared region. Furthermore, if the cpusets' allowed +memory sets are disjoint, "local" allocation is the only valid policy. |