diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 46 |
1 files changed, 18 insertions, 28 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 7b832c7..2decc59 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -483,7 +483,7 @@ config XTENSA_XT2000_SONIC This is the driver for the onboard card of the Xtensa XT2000 board. config MIPS_AU1X00_ENET - bool "MIPS AU1000 Ethernet support" + tristate "MIPS AU1000 Ethernet support" depends on SOC_AU1X00 select PHYLIB select CRC32 @@ -887,6 +887,13 @@ config BFIN_MAC_RMII help Use Reduced PHY MII Interface +config BFIN_MAC_USE_HWSTAMP + bool "Use IEEE 1588 hwstamp" + depends on BFIN_MAC && BF518 + default y + help + To support the IEEE 1588 Precision Time Protocol (PTP), select y here + config SMC9194 tristate "SMC 9194 support" depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN) @@ -1453,20 +1460,6 @@ config FORCEDETH To compile this driver as a module, choose M here. The module will be called forcedeth. -config FORCEDETH_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on FORCEDETH && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config CS89x0 tristate "CS89x0 support" depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \ @@ -1916,6 +1909,7 @@ config FEC bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)" depends on M523x || M527x || M5272 || M528x || M520x || M532x || \ MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5 + select PHYLIB help Say Y here if you want to use the built-in 10/100 Fast ethernet controller on some Motorola ColdFire and Freescale i.MX processors. @@ -2434,8 +2428,8 @@ config MV643XX_ETH config XILINX_LL_TEMAC tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver" + depends on PPC || MICROBLAZE select PHYLIB - depends on PPC_DCR_NATIVE help This driver supports the Xilinx 10/100/1000 LocalLink TEMAC core used in Xilinx Spartan and Virtex FPGAs @@ -2618,11 +2612,11 @@ config EHEA will be called ehea. config ENIC - tristate "Cisco 10G Ethernet NIC support" + tristate "Cisco VIC Ethernet NIC Support" depends on PCI && INET select INET_LRO help - This enables the support for the Cisco 10G Ethernet card. + This enables the support for the Cisco VIC Ethernet card. config IXGBE tristate "Intel(R) 10GbE PCI Express adapters support" @@ -2862,6 +2856,8 @@ source "drivers/ieee802154/Kconfig" source "drivers/s390/net/Kconfig" +source "drivers/net/caif/Kconfig" + config XEN_NETDEV_FRONTEND tristate "Xen network device frontend driver" depends on XEN @@ -3180,17 +3176,12 @@ config PPPOATM config PPPOL2TP tristate "PPP over L2TP (EXPERIMENTAL)" - depends on EXPERIMENTAL && PPP && INET + depends on EXPERIMENTAL && L2TP && PPP help Support for PPP-over-L2TP socket family. L2TP is a protocol used by ISPs and enterprises to tunnel PPP traffic over UDP tunnels. L2TP is replacing PPTP for VPN uses. - This kernel component handles only L2TP data packets: a - userland daemon handles L2TP the control protocol (tunnel - and session setup). One such daemon is OpenL2TP - (http://openl2tp.sourceforge.net/). - config SLIP tristate "SLIP (serial line) support" ---help--- @@ -3277,15 +3268,14 @@ config NET_FC "SCSI generic support". config NETCONSOLE - tristate "Network console logging support (EXPERIMENTAL)" - depends on EXPERIMENTAL + tristate "Network console logging support" ---help--- If you want to log kernel messages over the network, enable this. See <file:Documentation/networking/netconsole.txt> for details. config NETCONSOLE_DYNAMIC - bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)" - depends on NETCONSOLE && SYSFS && EXPERIMENTAL + bool "Dynamic reconfiguration of logging targets" + depends on NETCONSOLE && SYSFS select CONFIGFS_FS help This option enables the ability to dynamically reconfigure target |