1 files changed, 408 insertions, 0 deletions
diff --git a/drivers/net/ixp2000/ixp2400_rx.uc b/drivers/net/ixp2000/ixp2400_rx.uc
new file mode 100644
index 0000000..42a73e3
--- /dev/null
+++ b/drivers/net/ixp2000/ixp2400_rx.uc
@@ -0,0 +1,408 @@
+/*
+ * RX ucode for the Intel IXP2400 in POS-PHY mode.
+ * Copyright (C) 2004, 2005 Lennert Buytenhek
+ * Dedicated to Marija Kulikova.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Assumptions made in this code:
+ * - The IXP2400 MSF is configured for POS-PHY mode, in a mode where
+ *   only one full element list is used.  This includes, for example,
+ *   1x32 SPHY and 1x32 MPHY32, but not 4x8 SPHY or 1x32 MPHY4.  (This
+ *   is not an exhaustive list.)
+ * - The RBUF uses 64-byte mpackets.
+ * - RX descriptors reside in SRAM, and have the following format:
+ *	struct rx_desc
+ *	{
+ *	// to uengine
+ *		u32	buf_phys_addr;
+ *		u32	buf_length;
+ *
+ *	// from uengine
+ *		u32	channel;
+ *		u32	pkt_length;
+ *	};
+ * - Packet data resides in DRAM.
+ * - Packet buffer addresses are 8-byte aligned.
+ * - Scratch ring 0 is rx_pending.
+ * - Scratch ring 1 is rx_done, and has status condition 'full'.
+ * - The host triggers rx_done flush and rx_pending refill on seeing INTA.
+ * - This code is run on all eight threads of the microengine it runs on.
+ *
+ * Local memory is used for per-channel RX state.
+ */
+
+#define RX_THREAD_FREELIST_0		0x0030
+#define RBUF_ELEMENT_DONE		0x0044
+
+#define CHANNEL_FLAGS			*l$index0[0]
+#define CHANNEL_FLAG_RECEIVING		1
+#define PACKET_LENGTH			*l$index0[1]
+#define PACKET_CHECKSUM			*l$index0[2]
+#define BUFFER_HANDLE			*l$index0[3]
+#define BUFFER_START			*l$index0[4]
+#define BUFFER_LENGTH			*l$index0[5]
+
+#define CHANNEL_STATE_SIZE		24	// in bytes
+#define CHANNEL_STATE_SHIFT		5	// ceil(log2(state size))
+
+
+	.sig volatile sig1
+	.sig volatile sig2
+	.sig volatile sig3
+
+	.sig mpacket_arrived
+	.reg add_to_rx_freelist
+	.reg read $rsw0, $rsw1
+	.xfer_order $rsw0 $rsw1
+
+	.reg zero
+
+	/*
+	 * Initialise add_to_rx_freelist.
+	 */
+	.begin
+		.reg temp
+		.reg temp2
+
+		immed[add_to_rx_freelist, RX_THREAD_FREELIST_0]
+		immed_w1[add_to_rx_freelist, (&$rsw0 | (&mpacket_arrived << 12))]
+
+		local_csr_rd[ACTIVE_CTX_STS]
+		immed[temp, 0]
+		alu[temp2, temp, and, 0x1f]
+		alu_shf[add_to_rx_freelist, add_to_rx_freelist, or, temp2, <<20]
+		alu[temp2, temp, and, 0x80]
+		alu_shf[add_to_rx_freelist, add_to_rx_freelist, or, temp2, <<18]
+	.end
+
+	immed[zero, 0]
+
+	/*
+	 * Skip context 0 initialisation?
+	 */
+	.begin
+		br!=ctx[0, mpacket_receive_loop#]
+	.end
+
+	/*
+	 * Initialise local memory.
+	 */
+	.begin
+		.reg addr
+		.reg temp
+
+		immed[temp, 0]
+	init_local_mem_loop#:
+		alu_shf[addr, --, b, temp, <<CHANNEL_STATE_SHIFT]
+		local_csr_wr[ACTIVE_LM_ADDR_0, addr]
+		nop
+		nop
+		nop
+
+		immed[CHANNEL_FLAGS, 0]
+
+		alu[temp, temp, +, 1]
+		alu[--, temp, and, 0x20]
+		beq[init_local_mem_loop#]
+	.end
+
+	/*
+	 * Initialise signal pipeline.
+	 */
+	.begin
+		local_csr_wr[SAME_ME_SIGNAL, (&sig1 << 3)]
+		.set_sig sig1
+
+		local_csr_wr[SAME_ME_SIGNAL, (&sig2 << 3)]
+		.set_sig sig2
+
+		local_csr_wr[SAME_ME_SIGNAL, (&sig3 << 3)]
+		.set_sig sig3
+	.end
+
+mpacket_receive_loop#:
+	/*
+	 * Synchronise and wait for mpacket.
+	 */
+	.begin
+		ctx_arb[sig1]
+		local_csr_wr[SAME_ME_SIGNAL, (0x80 | (&sig1 << 3))]
+
+		msf[fast_wr, --, add_to_rx_freelist, 0]
+		.set_sig mpacket_arrived
+		ctx_arb[mpacket_arrived]
+		.set $rsw0 $rsw1
+	.end
+
+	/*
+	 * We halt if we see {inbparerr,parerr,null,soperror}.
+	 */
+	.begin
+		alu_shf[--, 0x1b, and, $rsw0, >>8]
+		bne[abort_rswerr#]
+	.end
+
+	/*
+	 * Point local memory pointer to this channel's state area.
+	 */
+	.begin
+		.reg chanaddr
+
+		alu[chanaddr, $rsw0, and, 0x1f]
+		alu_shf[chanaddr, --, b, chanaddr, <<CHANNEL_STATE_SHIFT]
+		local_csr_wr[ACTIVE_LM_ADDR_0, chanaddr]
+		nop
+		nop
+		nop
+	.end
+
+	/*
+	 * Check whether we received a SOP mpacket while we were already
+	 * working on a packet, or a non-SOP mpacket while there was no
+	 * packet pending.  (SOP == RECEIVING -> abort)  If everything's
+	 * okay, update the RECEIVING flag to reflect our new state.
+	 */
+	.begin
+		.reg temp
+		.reg eop
+
+		#if CHANNEL_FLAG_RECEIVING != 1
+		#error CHANNEL_FLAG_RECEIVING is not 1
+		#endif
+
+		alu_shf[temp, 1, and, $rsw0, >>15]
+		alu[temp, temp, xor, CHANNEL_FLAGS]
+		alu[--, temp, and, CHANNEL_FLAG_RECEIVING]
+		beq[abort_proterr#]
+
+		alu_shf[eop, 1, and, $rsw0, >>14]
+		alu[CHANNEL_FLAGS, temp, xor, eop]
+	.end
+
+	/*
+	 * Copy the mpacket into the right spot, and in case of EOP,
+	 * write back the descriptor and pass the packet on.
+	 */
+	.begin
+		.reg buffer_offset
+		.reg _packet_length
+		.reg _packet_checksum
+		.reg _buffer_handle
+		.reg _buffer_start
+		.reg _buffer_length
+
+		/*
+		 * Determine buffer_offset, _packet_length and
+		 * _packet_checksum.
+		 */
+		.begin
+			.reg temp
+
+			alu[--, 1, and, $rsw0, >>15]
+			beq[not_sop#]
+
+			immed[PACKET_LENGTH, 0]
+			immed[PACKET_CHECKSUM, 0]
+
+		not_sop#:
+			alu[buffer_offset, --, b, PACKET_LENGTH]
+			alu_shf[temp, 0xff, and, $rsw0, >>16]
+			alu[_packet_length, buffer_offset, +, temp]
+			alu[PACKET_LENGTH, --, b, _packet_length]
+
+			immed[temp, 0xffff]
+			alu[temp, $rsw1, and, temp]
+			alu[_packet_checksum, PACKET_CHECKSUM, +, temp]
+			alu[PACKET_CHECKSUM, --, b, _packet_checksum]
+		.end
+
+		/*
+		 * Allocate buffer in case of SOP.
+		 */
+		.begin
+			.reg temp
+
+			alu[temp, 1, and, $rsw0, >>15]
+			beq[skip_buffer_alloc#]
+
+			.begin
+				.sig zzz
+				.reg read $stemp $stemp2
+				.xfer_order $stemp $stemp2
+
+			rx_nobufs#:
+				scratch[get, $stemp, zero, 0, 1], ctx_swap[zzz]
+				alu[_buffer_handle, --, b, $stemp]
+				beq[rx_nobufs#]
+
+				sram[read, $stemp, _buffer_handle, 0, 2],
+								ctx_swap[zzz]
+				alu[_buffer_start, --, b, $stemp]
+				alu[_buffer_length, --, b, $stemp2]
+			.end
+
+		skip_buffer_alloc#:
+		.end
+
+		/*
+		 * Resynchronise.
+		 */
+		.begin
+			ctx_arb[sig2]
+			local_csr_wr[SAME_ME_SIGNAL, (0x80 | (&sig2 << 3))]
+		.end
+
+		/*
+		 * Synchronise buffer state.
+		 */
+		.begin
+			.reg temp
+
+			alu[temp, 1, and, $rsw0, >>15]
+			beq[copy_from_local_mem#]
+
+			alu[BUFFER_HANDLE, --, b, _buffer_handle]
+			alu[BUFFER_START, --, b, _buffer_start]
+			alu[BUFFER_LENGTH, --, b, _buffer_length]
+			br[sync_state_done#]
+
+		copy_from_local_mem#:
+			alu[_buffer_handle, --, b, BUFFER_HANDLE]
+			alu[_buffer_start, --, b, BUFFER_START]
+			alu[_buffer_length, --, b, BUFFER_LENGTH]
+
+		sync_state_done#:
+		.end
+
+#if 0
+		/*
+		 * Debug buffer state management.
+		 */
+		.begin
+			.reg temp
+
+			alu[temp, 1, and, $rsw0, >>14]
+			beq[no_poison#]
+			immed[BUFFER_HANDLE, 0xdead]
+			immed[BUFFER_START, 0xdead]
+			immed[BUFFER_LENGTH, 0xdead]
+		no_poison#:
+
+			immed[temp, 0xdead]
+			alu[--, _buffer_handle, -, temp]
+			beq[state_corrupted#]
+			alu[--, _buffer_start, -, temp]
+			beq[state_corrupted#]
+			alu[--, _buffer_length, -, temp]
+			beq[state_corrupted#]
+		.end
+#endif
+
+		/*
+		 * Check buffer length.
+		 */
+		.begin
+			alu[--, _buffer_length, -, _packet_length]
+			blo[buffer_overflow#]
+		.end
+
+		/*
+		 * Copy the mpacket and give back the RBUF element.
+		 */
+		.begin
+			.reg element
+			.reg xfer_size
+			.reg temp
+			.sig copy_sig
+
+			alu_shf[element, 0x7f, and, $rsw0, >>24]
+			alu_shf[xfer_size, 0xff, and, $rsw0, >>16]
+
+			alu[xfer_size, xfer_size, -, 1]
+			alu_shf[xfer_size, 0x10, or, xfer_size, >>3]
+			alu_shf[temp, 0x10, or, xfer_size, <<21]
+			alu_shf[temp, temp, or, element, <<11]
+			alu_shf[--, temp, or, 1, <<18]
+
+			dram[rbuf_rd, --, _buffer_start, buffer_offset, max_8],
+						indirect_ref, sig_done[copy_sig]
+			ctx_arb[copy_sig]
+
+			alu[temp, RBUF_ELEMENT_DONE, or, element, <<16]
+			msf[fast_wr, --, temp, 0]
+		.end
+
+		/*
+		 * If EOP, write back the packet descriptor.
+		 */
+		.begin
+			.reg write $stemp $stemp2
+			.xfer_order $stemp $stemp2
+			.sig zzz
+
+			alu_shf[--, 1, and, $rsw0, >>14]
+			beq[no_writeback#]
+
+			alu[$stemp, $rsw0, and, 0x1f]
+			alu[$stemp2, --, b, _packet_length]
+			sram[write, $stemp, _buffer_handle, 8, 2], ctx_swap[zzz]
+
+		no_writeback#:
+		.end
+
+		/*
+		 * Resynchronise.
+		 */
+		.begin
+			ctx_arb[sig3]
+			local_csr_wr[SAME_ME_SIGNAL, (0x80 | (&sig3 << 3))]
+		.end
+
+		/*
+		 * If EOP, put the buffer back onto the scratch ring.
+		 */
+		.begin
+			.reg write $stemp
+			.sig zzz
+
+			br_inp_state[SCR_Ring1_Status, rx_done_ring_overflow#]
+
+			alu_shf[--, 1, and, $rsw0, >>14]
+			beq[mpacket_receive_loop#]
+
+			alu[--, 1, and, $rsw0, >>10]
+			bne[rxerr#]
+
+			alu[$stemp, --, b, _buffer_handle]
+			scratch[put, $stemp, zero, 4, 1], ctx_swap[zzz]
+			cap[fast_wr, 0, XSCALE_INT_A]
+			br[mpacket_receive_loop#]
+
+		rxerr#:
+			alu[$stemp, --, b, _buffer_handle]
+			scratch[put, $stemp, zero, 0, 1], ctx_swap[zzz]
+			br[mpacket_receive_loop#]
+		.end
+	.end
+
+
+abort_rswerr#:
+	halt
+
+abort_proterr#:
+	halt
+
+state_corrupted#:
+	halt
+
+buffer_overflow#:
+	halt
+
+rx_done_ring_overflow#:
+	halt
+
+