diff options
Diffstat (limited to 'include/asm-arm/arch-aaec2000/aaec2000.h')
| -rw-r--r-- | include/asm-arm/arch-aaec2000/aaec2000.h | 207 |
1 files changed, 0 insertions, 207 deletions
diff --git a/include/asm-arm/arch-aaec2000/aaec2000.h b/include/asm-arm/arch-aaec2000/aaec2000.h deleted file mode 100644 index a6d1ee0..0000000 --- a/include/asm-arm/arch-aaec2000/aaec2000.h +++ /dev/null @@ -1,207 +0,0 @@ -/* - * linux/include/asm-arm/arch-aaec2000/aaec2000.h - * - * AAEC-2000 registers definition - * - * Copyright (c) 2005 Nicolas Bellido Y Ortega - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#ifndef __ASM_ARCH_AAEC2000_H -#define __ASM_ARCH_AAEC2000_H - -#ifndef __ASM_ARCH_HARDWARE_H -#error You must include hardware.h not this file -#endif /* __ASM_ARCH_HARDWARE_H */ - -/* Chip selects */ -#define AAEC_CS0 0x00000000 -#define AAEC_CS1 0x10000000 -#define AAEC_CS2 0x20000000 -#define AAEC_CS3 0x30000000 - -/* Flash */ -#define AAEC_FLASH_BASE AAEC_CS0 -#define AAEC_FLASH_SIZE SZ_64M - -/* Interrupt controller */ -#define IRQ_BASE __REG(0x80000500) -#define IRQ_INTSR __REG(0x80000500) /* Int Status Register */ -#define IRQ_INTRSR __REG(0x80000504) /* Int Raw (unmasked) Status */ -#define IRQ_INTENS __REG(0x80000508) /* Int Enable Set */ -#define IRQ_INTENC __REG(0x8000050c) /* Int Enable Clear */ - -/* UART 1 */ -#define UART1_BASE __REG(0x80000600) -#define UART1_DR __REG(0x80000600) /* Data/FIFO Register */ -#define UART1_LCR __REG(0x80000604) /* Link Control Register */ -#define UART1_BRCR __REG(0x80000608) /* Baud Rate Control Register */ -#define UART1_CR __REG(0x8000060c) /* Control Register */ -#define UART1_SR __REG(0x80000610) /* Status Register */ -#define UART1_INT __REG(0x80000614) /* Interrupt Status Register */ -#define UART1_INTM __REG(0x80000618) /* Interrupt Mask Register */ -#define UART1_INTRES __REG(0x8000061c) /* Int Result (masked status) Register */ - -/* UART 2 */ -#define UART2_BASE __REG(0x80000700) -#define UART2_DR __REG(0x80000700) /* Data/FIFO Register */ -#define UART2_LCR __REG(0x80000704) /* Link Control Register */ -#define UART2_BRCR __REG(0x80000708) /* Baud Rate Control Register */ -#define UART2_CR __REG(0x8000070c) /* Control Register */ -#define UART2_SR __REG(0x80000710) /* Status Register */ -#define UART2_INT __REG(0x80000714) /* Interrupt Status Register */ -#define UART2_INTM __REG(0x80000718) /* Interrupt Mask Register */ -#define UART2_INTRES __REG(0x8000071c) /* Int Result (masked status) Register */ - -/* UART 3 */ -#define UART3_BASE __REG(0x80000800) -#define UART3_DR __REG(0x80000800) /* Data/FIFO Register */ -#define UART3_LCR __REG(0x80000804) /* Link Control Register */ -#define UART3_BRCR __REG(0x80000808) /* Baud Rate Control Register */ -#define UART3_CR __REG(0x8000080c) /* Control Register */ -#define UART3_SR __REG(0x80000810) /* Status Register */ -#define UART3_INT __REG(0x80000814) /* Interrupt Status Register */ -#define UART3_INTM __REG(0x80000818) /* Interrupt Mask Register */ -#define UART3_INTRES __REG(0x8000081c) /* Int Result (masked status) Register */ - -/* These are used in some places */ -#define _UART1_BASE __PREG(UART1_BASE) -#define _UART2_BASE __PREG(UART2_BASE) -#define _UART3_BASE __PREG(UART3_BASE) - -/* UART Registers Offsets */ -#define UART_DR 0x00 -#define UART_LCR 0x04 -#define UART_BRCR 0x08 -#define UART_CR 0x0c -#define UART_SR 0x10 -#define UART_INT 0x14 -#define UART_INTM 0x18 -#define UART_INTRES 0x1c - -/* UART_LCR Bitmask */ -#define UART_LCR_BRK (1 << 0) /* Send Break */ -#define UART_LCR_PEN (1 << 1) /* Parity Enable */ -#define UART_LCR_EP (1 << 2) /* Even/Odd Parity */ -#define UART_LCR_S2 (1 << 3) /* One/Two Stop bits */ -#define UART_LCR_FIFO (1 << 4) /* FIFO Enable */ -#define UART_LCR_WL5 (0 << 5) /* Word Length - 5 bits */ -#define UART_LCR_WL6 (1 << 5) /* Word Length - 6 bits */ -#define UART_LCR_WL7 (1 << 6) /* Word Length - 7 bits */ -#define UART_LCR_WL8 (1 << 7) /* Word Length - 8 bits */ - -/* UART_CR Bitmask */ -#define UART_CR_EN (1 << 0) /* UART Enable */ -#define UART_CR_SIR (1 << 1) /* IrDA SIR Enable */ -#define UART_CR_SIRLP (1 << 2) /* Low Power IrDA Enable */ -#define UART_CR_RXP (1 << 3) /* Receive Pin Polarity */ -#define UART_CR_TXP (1 << 4) /* Transmit Pin Polarity */ -#define UART_CR_MXP (1 << 5) /* Modem Pin Polarity */ -#define UART_CR_LOOP (1 << 6) /* Loopback Mode */ - -/* UART_SR Bitmask */ -#define UART_SR_CTS (1 << 0) /* Clear To Send Status */ -#define UART_SR_DSR (1 << 1) /* Data Set Ready Status */ -#define UART_SR_DCD (1 << 2) /* Data Carrier Detect Status */ -#define UART_SR_TxBSY (1 << 3) /* Transmitter Busy Status */ -#define UART_SR_RxFE (1 << 4) /* Receive FIFO Empty Status */ -#define UART_SR_TxFF (1 << 5) /* Transmit FIFO Full Status */ -#define UART_SR_RxFF (1 << 6) /* Receive FIFO Full Status */ -#define UART_SR_TxFE (1 << 7) /* Transmit FIFO Empty Status */ - -/* UART_INT Bitmask */ -#define UART_INT_RIS (1 << 0) /* Rx Interrupt */ -#define UART_INT_TIS (1 << 1) /* Tx Interrupt */ -#define UART_INT_MIS (1 << 2) /* Modem Interrupt */ -#define UART_INT_RTIS (1 << 3) /* Receive Timeout Interrupt */ - -/* Timer 1 */ -#define TIMER1_BASE __REG(0x80000c00) -#define TIMER1_LOAD __REG(0x80000c00) /* Timer 1 Load Register */ -#define TIMER1_VAL __REG(0x80000c04) /* Timer 1 Value Register */ -#define TIMER1_CTRL __REG(0x80000c08) /* Timer 1 Control Register */ -#define TIMER1_CLEAR __REG(0x80000c0c) /* Timer 1 Clear Register */ - -/* Timer 2 */ -#define TIMER2_BASE __REG(0x80000d00) -#define TIMER2_LOAD __REG(0x80000d00) /* Timer 2 Load Register */ -#define TIMER2_VAL __REG(0x80000d04) /* Timer 2 Value Register */ -#define TIMER2_CTRL __REG(0x80000d08) /* Timer 2 Control Register */ -#define TIMER2_CLEAR __REG(0x80000d0c) /* Timer 2 Clear Register */ - -/* Timer 3 */ -#define TIMER3_BASE __REG(0x80000e00) -#define TIMER3_LOAD __REG(0x80000e00) /* Timer 3 Load Register */ -#define TIMER3_VAL __REG(0x80000e04) /* Timer 3 Value Register */ -#define TIMER3_CTRL __REG(0x80000e08) /* Timer 3 Control Register */ -#define TIMER3_CLEAR __REG(0x80000e0c) /* Timer 3 Clear Register */ - -/* Timer Control register bits */ -#define TIMER_CTRL_ENABLE (1 << 7) /* Enable (Start Timer) */ -#define TIMER_CTRL_PERIODIC (1 << 6) /* Periodic Running Mode */ -#define TIMER_CTRL_FREE_RUNNING (0 << 6) /* Normal Running Mode */ -#define TIMER_CTRL_CLKSEL_508K (1 << 3) /* 508KHz Clock select (Timer 1, 2) */ -#define TIMER_CTRL_CLKSEL_2K (0 << 3) /* 2KHz Clock Select (Timer 1, 2) */ - -/* Power and State Control */ -#define POWER_BASE __REG(0x80000400) -#define POWER_PWRSR __REG(0x80000400) /* Power Status Register */ -#define POWER_PWRCNT __REG(0x80000404) /* Power/Clock control */ -#define POWER_HALT __REG(0x80000408) /* Power Idle Mode */ -#define POWER_STDBY __REG(0x8000040c) /* Power Standby Mode */ -#define POWER_BLEOI __REG(0x80000410) /* Battery Low End of Interrupt */ -#define POWER_MCEOI __REG(0x80000414) /* Media Changed EoI */ -#define POWER_TEOI __REG(0x80000418) /* Tick EoI */ -#define POWER_STFCLR __REG(0x8000041c) /* NbFlg, RSTFlg, PFFlg, CLDFlg Clear */ -#define POWER_CLKSET __REG(0x80000420) /* Clock Speed Control */ - -/* GPIO Registers */ -#define AAEC_GPIO_PHYS 0x80000e00 - -#define AAEC_GPIO_PADR __REG(AAEC_GPIO_PHYS + 0x00) -#define AAEC_GPIO_PBDR __REG(AAEC_GPIO_PHYS + 0x04) -#define AAEC_GPIO_PCDR __REG(AAEC_GPIO_PHYS + 0x08) -#define AAEC_GPIO_PDDR __REG(AAEC_GPIO_PHYS + 0x0c) -#define AAEC_GPIO_PADDR __REG(AAEC_GPIO_PHYS + 0x10) -#define AAEC_GPIO_PBDDR __REG(AAEC_GPIO_PHYS + 0x14) -#define AAEC_GPIO_PCDDR __REG(AAEC_GPIO_PHYS + 0x18) -#define AAEC_GPIO_PDDDR __REG(AAEC_GPIO_PHYS + 0x1c) -#define AAEC_GPIO_PEDR __REG(AAEC_GPIO_PHYS + 0x20) -#define AAEC_GPIO_PEDDR __REG(AAEC_GPIO_PHYS + 0x24) -#define AAEC_GPIO_KSCAN __REG(AAEC_GPIO_PHYS + 0x28) -#define AAEC_GPIO_PINMUX __REG(AAEC_GPIO_PHYS + 0x2c) -#define AAEC_GPIO_PFDR __REG(AAEC_GPIO_PHYS + 0x30) -#define AAEC_GPIO_PFDDR __REG(AAEC_GPIO_PHYS + 0x34) -#define AAEC_GPIO_PGDR __REG(AAEC_GPIO_PHYS + 0x38) -#define AAEC_GPIO_PGDDR __REG(AAEC_GPIO_PHYS + 0x3c) -#define AAEC_GPIO_PHDR __REG(AAEC_GPIO_PHYS + 0x40) -#define AAEC_GPIO_PHDDR __REG(AAEC_GPIO_PHYS + 0x44) -#define AAEC_GPIO_RAZ __REG(AAEC_GPIO_PHYS + 0x48) -#define AAEC_GPIO_INTTYPE1 __REG(AAEC_GPIO_PHYS + 0x4c) -#define AAEC_GPIO_INTTYPE2 __REG(AAEC_GPIO_PHYS + 0x50) -#define AAEC_GPIO_FEOI __REG(AAEC_GPIO_PHYS + 0x54) -#define AAEC_GPIO_INTEN __REG(AAEC_GPIO_PHYS + 0x58) -#define AAEC_GPIO_INTSTATUS __REG(AAEC_GPIO_PHYS + 0x5c) -#define AAEC_GPIO_RAWINTSTATUS __REG(AAEC_GPIO_PHYS + 0x60) -#define AAEC_GPIO_DB __REG(AAEC_GPIO_PHYS + 0x64) -#define AAEC_GPIO_PAPINDR __REG(AAEC_GPIO_PHYS + 0x68) -#define AAEC_GPIO_PBPINDR __REG(AAEC_GPIO_PHYS + 0x6c) -#define AAEC_GPIO_PCPINDR __REG(AAEC_GPIO_PHYS + 0x70) -#define AAEC_GPIO_PDPINDR __REG(AAEC_GPIO_PHYS + 0x74) -#define AAEC_GPIO_PEPINDR __REG(AAEC_GPIO_PHYS + 0x78) -#define AAEC_GPIO_PFPINDR __REG(AAEC_GPIO_PHYS + 0x7c) -#define AAEC_GPIO_PGPINDR __REG(AAEC_GPIO_PHYS + 0x80) -#define AAEC_GPIO_PHPINDR __REG(AAEC_GPIO_PHYS + 0x84) - -#define AAEC_GPIO_PINMUX_PE0CON (1 << 0) -#define AAEC_GPIO_PINMUX_PD0CON (1 << 1) -#define AAEC_GPIO_PINMUX_CODECON (1 << 2) -#define AAEC_GPIO_PINMUX_UART3CON (1 << 3) - -/* LCD Controller */ -#define AAEC_CLCD_PHYS 0x80003000 - -#endif /* __ARM_ARCH_AAEC2000_H */ |