diff options
Diffstat (limited to 'include/asm-arm/arch-sa1100/simpad.h')
| -rw-r--r-- | include/asm-arm/arch-sa1100/simpad.h | 112 |
1 files changed, 0 insertions, 112 deletions
diff --git a/include/asm-arm/arch-sa1100/simpad.h b/include/asm-arm/arch-sa1100/simpad.h deleted file mode 100644 index 034301d..0000000 --- a/include/asm-arm/arch-sa1100/simpad.h +++ /dev/null @@ -1,112 +0,0 @@ -/* - * linux/include/asm-arm/arch-sa1100/simpad.h - * - * based of assabet.h same as HUW_Webpanel - * - * This file contains the hardware specific definitions for SIMpad - * - * 2001/05/14 Juergen Messerer <juergen.messerer@freesurf.ch> - */ - -#ifndef __ASM_ARCH_SIMPAD_H -#define __ASM_ARCH_SIMPAD_H - - -#define GPIO_UART1_RTS GPIO_GPIO14 -#define GPIO_UART1_DTR GPIO_GPIO7 -#define GPIO_UART1_CTS GPIO_GPIO8 -#define GPIO_UART1_DCD GPIO_GPIO23 -#define GPIO_UART1_DSR GPIO_GPIO6 - -#define GPIO_UART3_RTS GPIO_GPIO12 -#define GPIO_UART3_DTR GPIO_GPIO16 -#define GPIO_UART3_CTS GPIO_GPIO13 -#define GPIO_UART3_DCD GPIO_GPIO18 -#define GPIO_UART3_DSR GPIO_GPIO17 - -#define GPIO_POWER_BUTTON GPIO_GPIO0 -#define GPIO_UCB1300_IRQ GPIO_GPIO22 /* UCB GPIO and touchscreen */ - -#define IRQ_UART1_CTS IRQ_GPIO15 -#define IRQ_UART1_DCD GPIO_GPIO23 -#define IRQ_UART1_DSR GPIO_GPIO6 -#define IRQ_UART3_CTS GPIO_GPIO13 -#define IRQ_UART3_DCD GPIO_GPIO18 -#define IRQ_UART3_DSR GPIO_GPIO17 - -#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22 -#define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0 - - -/*--- PCMCIA ---*/ -#define GPIO_CF_CD GPIO_GPIO24 -#define GPIO_CF_IRQ GPIO_GPIO1 -#define IRQ_GPIO_CF_IRQ IRQ_GPIO1 -#define IRQ_GPIO_CF_CD IRQ_GPIO24 - -/*--- SmartCard ---*/ -#define GPIO_SMART_CARD GPIO_GPIO10 -#define IRQ_GPIO_SMARD_CARD IRQ_GPIO10 - -// CS3 Latch is write only, a shadow is necessary - -#define CS3BUSTYPE unsigned volatile long -#define CS3_BASE 0xf1000000 - -#define VCC_5V_EN 0x0001 // For 5V PCMCIA -#define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA -#define EN1 0x0004 // This is only for EPROM's -#define EN0 0x0008 // Both should be enable for 3.3V or 5V -#define DISPLAY_ON 0x0010 -#define PCMCIA_BUFF_DIS 0x0020 -#define MQ_RESET 0x0040 -#define PCMCIA_RESET 0x0080 -#define DECT_POWER_ON 0x0100 -#define IRDA_SD 0x0200 // Shutdown for powersave -#define RS232_ON 0x0400 -#define SD_MEDIAQ 0x0800 // Shutdown for powersave -#define LED2_ON 0x1000 -#define IRDA_MODE 0x2000 // Fast/Slow IrDA mode -#define ENABLE_5V 0x4000 // Enable 5V circuit -#define RESET_SIMCARD 0x8000 - -#define RS232_ENABLE 0x0440 -#define PCMCIAMASK 0x402f - - -struct simpad_battery { - unsigned char ac_status; /* line connected yes/no */ - unsigned char status; /* battery loading yes/no */ - unsigned char percentage; /* percentage loaded */ - unsigned short life; /* life till empty */ -}; - -/* These should match the apm_bios.h definitions */ -#define SIMPAD_AC_STATUS_AC_OFFLINE 0x00 -#define SIMPAD_AC_STATUS_AC_ONLINE 0x01 -#define SIMPAD_AC_STATUS_AC_BACKUP 0x02 /* What does this mean? */ -#define SIMPAD_AC_STATUS_AC_UNKNOWN 0xff - -/* These bitfields are rarely "or'd" together */ -#define SIMPAD_BATT_STATUS_HIGH 0x01 -#define SIMPAD_BATT_STATUS_LOW 0x02 -#define SIMPAD_BATT_STATUS_CRITICAL 0x04 -#define SIMPAD_BATT_STATUS_CHARGING 0x08 -#define SIMPAD_BATT_STATUS_CHARGE_MAIN 0x10 -#define SIMPAD_BATT_STATUS_DEAD 0x20 /* Battery will not charge */ -#define SIMPAD_BATT_NOT_INSTALLED 0x20 /* For expansion pack batteries */ -#define SIMPAD_BATT_STATUS_FULL 0x40 /* Battery fully charged (and connected to AC) */ -#define SIMPAD_BATT_STATUS_NOBATT 0x80 -#define SIMPAD_BATT_STATUS_UNKNOWN 0xff - -extern int simpad_get_battery(struct simpad_battery* ); - -#endif // __ASM_ARCH_SIMPAD_H - - - - - - - - |