[AVR32] Use per-controller spi_board_info structures

Set up one spi_board_info array per controller and pass this to
at32_add_device_spi so that it can set up any GPIO pins for chip
selects based on this information.

Extracted from a patch by David Brownell and adapted slightly.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

3 files changed, 44 insertions, 24 deletions

diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index d47e39f..5974768 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -8,7 +8,6 @@
  * published by the Free Software Foundation.
  */
 #include <linux/clk.h>
-#include <linux/device.h>
 #include <linux/etherdevice.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
@@ -36,12 +35,11 @@ static struct eth_addr __initdata hw_addr[2];
 static struct eth_platform_data __initdata eth_data[2];
 extern struct lcdc_platform_data atstk1000_fb0_data;
 
-static struct spi_board_info spi_board_info[] __initdata = {
+static struct spi_board_info spi0_board_info[] __initdata = {
 	{
+		/* QVGA display */
 		.modalias	= "ltv350qv",
-		.controller_data = (void *)GPIO_PIN_PA(4),
 		.max_speed_hz	= 16000000,
-		.bus_num	= 0,
 		.chip_select	= 1,
 	},
 };
@@ -149,8 +147,7 @@ static int __init atstk1002_init(void)
 
 	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
 
-	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
-	at32_add_device_spi(0);
+	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
 	at32_add_device_lcdc(0, &atstk1000_fb0_data);
 
 	return 0;
diff --git a/arch/avr32/mach-at32ap/at32ap7000.c b/arch/avr32/mach-at32ap/at32ap7000.c
index a5037aa..bc23550 100644
--- a/arch/avr32/mach-at32ap/at32ap7000.c
+++ b/arch/avr32/mach-at32ap/at32ap7000.c
@@ -8,6 +8,7 @@
 #include <linux/clk.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/spi/spi.h>
 
 #include <asm/io.h>
 
@@ -751,8 +752,41 @@ static struct resource atmel_spi1_resource[] = {
 DEFINE_DEV(atmel_spi, 1);
 DEV_CLK(spi_clk, atmel_spi1, pba, 1);
 
-struct platform_device *__init at32_add_device_spi(unsigned int id)
+static void
+at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b,
+		      unsigned int n, const u8 *pins)
 {
+	unsigned int pin, mode;
+
+	for (; n; n--, b++) {
+		b->bus_num = bus_num;
+		if (b->chip_select >= 4)
+			continue;
+		pin = (unsigned)b->controller_data;
+		if (!pin) {
+			pin = pins[b->chip_select];
+			b->controller_data = (void *)pin;
+		}
+		mode = AT32_GPIOF_OUTPUT;
+		if (!(b->mode & SPI_CS_HIGH))
+			mode |= AT32_GPIOF_HIGH;
+		at32_select_gpio(pin, mode);
+	}
+}
+
+struct platform_device *__init
+at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n)
+{
+	/*
+	 * Manage the chipselects as GPIOs, normally using the same pins
+	 * the SPI controller expects; but boards can use other pins.
+	 */
+	static u8 __initdata spi0_pins[] =
+		{ GPIO_PIN_PA(3), GPIO_PIN_PA(4),
+		  GPIO_PIN_PA(5), GPIO_PIN_PA(20), };
+	static u8 __initdata spi1_pins[] =
+		{ GPIO_PIN_PB(2), GPIO_PIN_PB(3),
+		  GPIO_PIN_PB(4), GPIO_PIN_PA(27), };
 	struct platform_device *pdev;
 
 	switch (id) {
@@ -761,14 +795,7 @@ struct platform_device *__init at32_add_device_spi(unsigned int id)
 		select_peripheral(PA(0),  PERIPH_A, 0);	/* MISO	 */
 		select_peripheral(PA(1),  PERIPH_A, 0);	/* MOSI	 */
 		select_peripheral(PA(2),  PERIPH_A, 0);	/* SCK	 */
-
-		/* NPCS[2:0] */
-		at32_select_gpio(GPIO_PIN_PA(3),
-				 AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
-		at32_select_gpio(GPIO_PIN_PA(4),
-				 AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
-		at32_select_gpio(GPIO_PIN_PA(5),
-				 AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
+		at32_spi_setup_slaves(0, b, n, spi0_pins);
 		break;
 
 	case 1:
@@ -776,20 +803,14 @@ struct platform_device *__init at32_add_device_spi(unsigned int id)
 		select_peripheral(PB(0),  PERIPH_B, 0);	/* MISO  */
 		select_peripheral(PB(1),  PERIPH_B, 0);	/* MOSI  */
 		select_peripheral(PB(5),  PERIPH_B, 0);	/* SCK   */
-
-		/* NPCS[2:0] */
-		at32_select_gpio(GPIO_PIN_PB(2),
-				 AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
-		at32_select_gpio(GPIO_PIN_PB(3),
-				 AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
-		at32_select_gpio(GPIO_PIN_PB(4),
-				 AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
+		at32_spi_setup_slaves(1, b, n, spi1_pins);
 		break;
 
 	default:
 		return NULL;
 	}
 
+	spi_register_board_info(b, n);
 	platform_device_register(pdev);
 	return pdev;
 }
diff --git a/include/asm-avr32/arch-at32ap/board.h b/include/asm-avr32/arch-at32ap/board.h
index b120ee0..1a7b07d 100644
--- a/include/asm-avr32/arch-at32ap/board.h
+++ b/include/asm-avr32/arch-at32ap/board.h
@@ -26,7 +26,9 @@ struct eth_platform_data {
 struct platform_device *
 at32_add_device_eth(unsigned int id, struct eth_platform_data *data);
 
-struct platform_device *at32_add_device_spi(unsigned int id);
+struct spi_board_info;
+struct platform_device *
+at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
 
 struct lcdc_platform_data {
 	unsigned long fbmem_start;