wimax: Makefile, Kconfig and docbook linkage for the stack

This patch provides Makefile and KConfig for the WiMAX stack,
integrating them into the networking stack's Makefile, Kconfig and
doc-book templates.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

5 files changed, 62 insertions, 0 deletions

diff --git a/Documentation/DocBook/networking.tmpl b/Documentation/DocBook/networking.tmpl
index 627707a..59ad69a 100644
--- a/Documentation/DocBook/networking.tmpl
+++ b/Documentation/DocBook/networking.tmpl
@@ -74,6 +74,14 @@
 !Enet/sunrpc/rpcb_clnt.c
 !Enet/sunrpc/clnt.c
      </sect1>
+     <sect1><title>WiMAX</title>
+!Enet/wimax/op-msg.c
+!Enet/wimax/op-reset.c
+!Enet/wimax/op-rfkill.c
+!Enet/wimax/stack.c
+!Iinclude/net/wimax.h
+!Iinclude/linux/wimax.h
+     </sect1>
   </chapter>
 
   <chapter id="netdev">
diff --git a/net/Kconfig b/net/Kconfig
index 6ec2cce..bf27760 100644
--- a/net/Kconfig
+++ b/net/Kconfig
@@ -254,6 +254,8 @@ source "net/mac80211/Kconfig"
 
 endif # WIRELESS
 
+source "net/wimax/Kconfig"
+
 source "net/rfkill/Kconfig"
 source "net/9p/Kconfig"
 
diff --git a/net/Makefile b/net/Makefile
index ba44604..0fcce89 100644
--- a/net/Makefile
+++ b/net/Makefile
@@ -63,3 +63,4 @@ endif
 ifeq ($(CONFIG_NET),y)
 obj-$(CONFIG_SYSCTL)		+= sysctl_net.o
 endif
+obj-$(CONFIG_WIMAX)		+= wimax/
diff --git a/net/wimax/Kconfig b/net/wimax/Kconfig
new file mode 100644
index 0000000..0bdbb69
--- /dev/null
+++ b/net/wimax/Kconfig
@@ -0,0 +1,38 @@
+#
+# WiMAX LAN device configuration
+#
+
+menuconfig WIMAX
+	tristate "WiMAX Wireless Broadband support"
+	help
+
+	  Select to configure support for devices that provide
+	  wireless broadband connectivity using the WiMAX protocol
+	  (IEEE 802.16).
+
+	  Please note that most of these devices require signing up
+	  for a service plan with a provider.
+
+	  The different WiMAX drivers can be enabled in the menu entry
+
+	  Device Drivers > Network device support > WiMAX Wireless
+	  Broadband devices
+
+	  If unsure, it is safe to select M (module).
+
+config WIMAX_DEBUG_LEVEL
+	int "WiMAX debug level"
+	depends on WIMAX
+	default 8
+	help
+
+	  Select the maximum debug verbosity level to be compiled into
+	  the WiMAX stack code.
+
+	  By default, debug messages are disabled at runtime and can
+	  be selectively enabled for different parts of the code using
+	  the sysfs debug-levels file.
+
+	  If set at zero, this will compile out all the debug code.
+
+	  It is recommended that it is left at 8.
diff --git a/net/wimax/Makefile b/net/wimax/Makefile
new file mode 100644
index 0000000..5b80b94
--- /dev/null
+++ b/net/wimax/Makefile
@@ -0,0 +1,13 @@
+
+obj-$(CONFIG_WIMAX)		+= wimax.o
+
+wimax-y :=		\
+	id-table.o	\
+	op-msg.o	\
+	op-reset.o	\
+	op-rfkill.o	\
+	stack.o
+
+wimax-$(CONFIG_DEBUG_FS) += debugfs.o
+
+