Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
  MAINTAINERS: EB110ATX is not ebsa110
  MAINTAINERS: update Eric Miao's email address and status
  fb: add support of LCD display controller on pxa168/910 (base layer)
  [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
  [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
  [ARM] 5544/1: Trust PrimeCell resource sizes
  [ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
  [ARM] pxa/sharpsl_pm: drop set_irq_type calls
  [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
  [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
  [ARM] sa1100: remove unused collie_pm.c
  [ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
  [ARM] 5550/1: Add default configure file for w90p910 platform
  [ARM] 5549/1: Add clock api for w90p910 platform.
  [ARM] 5548/1: Add gpio api for w90p910 platform
  [ARM] 5551/1: Add multi-function pin api for w90p910 platform.
  [ARM] Make ARM_VIC_NR depend on ARM_VIC
  [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
  ARM: OMAP4: SMP: Update defconfig for OMAP4430
  ARM: OMAP4: SMP: Enable SMP support for OMAP4430
  ...

1 files changed, 10 insertions, 64 deletions

diff --git a/arch/arm/mach-davinci/serial.c b/arch/arm/mach-davinci/serial.c
index 6950757..c530c73 100644
--- a/arch/arm/mach-davinci/serial.c
+++ b/arch/arm/mach-davinci/serial.c
@@ -33,6 +33,8 @@
 #include <mach/serial.h>
 #include <mach/irqs.h>
 #include <mach/cputype.h>
+#include <mach/common.h>
+
 #include "clock.h"
 
 static inline unsigned int serial_read_reg(struct plat_serial8250_port *up,
@@ -49,44 +51,6 @@ static inline void serial_write_reg(struct plat_serial8250_port *p, int offset,
 	__raw_writel(value, IO_ADDRESS(p->mapbase) + offset);
 }
 
-static struct plat_serial8250_port serial_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART0_BASE,
-		.irq		= IRQ_UARTINT0,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-	},
-	{
-		.mapbase	= DAVINCI_UART1_BASE,
-		.irq		= IRQ_UARTINT1,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-	},
-	{
-		.mapbase	= DAVINCI_UART2_BASE,
-		.irq		= IRQ_UARTINT2,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-	},
-	{
-		.flags		= 0
-	},
-};
-
-static struct platform_device serial_device = {
-	.name			= "serial8250",
-	.id			= PLAT8250_DEV_PLATFORM,
-	.dev			= {
-		.platform_data	= serial_platform_data,
-	},
-};
-
 static void __init davinci_serial_reset(struct plat_serial8250_port *p)
 {
 	unsigned int pwremu = 0;
@@ -106,35 +70,22 @@ static void __init davinci_serial_reset(struct plat_serial8250_port *p)
 				 UART_DM646X_SCR_TX_WATERMARK);
 }
 
-void __init davinci_serial_init(struct davinci_uart_config *info)
+int __init davinci_serial_init(struct davinci_uart_config *info)
 {
 	int i;
 	char name[16];
 	struct clk *uart_clk;
-	struct device *dev = &serial_device.dev;
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+	struct device *dev = &soc_info->serial_dev->dev;
+	struct plat_serial8250_port *p = dev->platform_data;
 
 	/*
 	 * Make sure the serial ports are muxed on at this point.
-	 * You have to mux them off in device drivers later on
-	 * if not needed.
+	 * You have to mux them off in device drivers later on if not needed.
 	 */
-	for (i = 0; i < DAVINCI_MAX_NR_UARTS; i++) {
-		struct plat_serial8250_port *p = serial_platform_data + i;
-
-		if (!(info->enabled_uarts & (1 << i))) {
-			p->flags = 0;
+	for (i = 0; i < DAVINCI_MAX_NR_UARTS; i++, p++) {
+		if (!(info->enabled_uarts & (1 << i)))
 			continue;
-		}
-
-		if (cpu_is_davinci_dm646x())
-			p->iotype = UPIO_MEM32;
-
-		if (cpu_is_davinci_dm355()) {
-			if (i == 2) {
-				p->mapbase = (unsigned long)DM355_UART2_BASE;
-				p->irq = IRQ_DM355_UARTINT2;
-			}
-		}
 
 		sprintf(name, "uart%d", i);
 		uart_clk = clk_get(dev, name);
@@ -147,11 +98,6 @@ void __init davinci_serial_init(struct davinci_uart_config *info)
 			davinci_serial_reset(p);
 		}
 	}
-}
 
-static int __init davinci_init(void)
-{
-	return platform_device_register(&serial_device);
+	return platform_device_register(soc_info->serial_dev);
 }
-
-arch_initcall(davinci_init);