diff options
Diffstat (limited to 'Documentation/laptops/thinkpad-acpi.txt')
| -rw-r--r-- | Documentation/laptops/thinkpad-acpi.txt | 145 |
1 files changed, 68 insertions, 77 deletions
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index 75afa12..1565eef 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -292,13 +292,13 @@ sysfs notes: Warning: when in NVRAM mode, the volume up/down/mute keys are synthesized according to changes in the mixer, - so you have to use volume up or volume down to unmute, - as per the ThinkPad volume mixer user interface. When - in ACPI event mode, volume up/down/mute are reported as - separate events, but this behaviour may be corrected in - future releases of this driver, in which case the - ThinkPad volume mixer user interface semantics will be - enforced. + which uses a single volume up or volume down hotkey + press to unmute, as per the ThinkPad volume mixer user + interface. When in ACPI event mode, volume up/down/mute + events are reported by the firmware and can behave + differently (and that behaviour changes with firmware + version -- not just with firmware models -- as well as + OSI(Linux) state). hotkey_poll_freq: frequency in Hz for hot key polling. It must be between @@ -309,7 +309,7 @@ sysfs notes: will cause hot key presses that require NVRAM polling to never be reported. - Setting hotkey_poll_freq too low will cause repeated + Setting hotkey_poll_freq too low may cause repeated pressings of the same hot key to be misreported as a single key press, or to not even be detected at all. The recommended polling frequency is 10Hz. @@ -397,6 +397,7 @@ ACPI Scan event code Key Notes 0x1001 0x00 FN+F1 - + 0x1002 0x01 FN+F2 IBM: battery (rare) Lenovo: Screen lock @@ -404,7 +405,8 @@ event code Key Notes this hot key, even with hot keys disabled or with Fn+F3 masked off - IBM: screen lock + IBM: screen lock, often turns + off the ThinkLight as side-effect Lenovo: battery 0x1004 0x03 FN+F4 Sleep button (ACPI sleep button @@ -433,7 +435,8 @@ event code Key Notes Do you feel lucky today? 0x1008 0x07 FN+F8 IBM: toggle screen expand - Lenovo: configure UltraNav + Lenovo: configure UltraNav, + or toggle screen expand 0x1009 0x08 FN+F9 - .. .. .. @@ -444,7 +447,7 @@ event code Key Notes either through the ACPI event, or through a hotkey event. The firmware may refuse to - generate further FN+F4 key + generate further FN+F12 key press events until a S3 or S4 ACPI sleep cycle is performed, or some time passes. @@ -512,15 +515,19 @@ events for switches: SW_RFKILL_ALL T60 and later hardware rfkill rocker switch SW_TABLET_MODE Tablet ThinkPads HKEY events 0x5009 and 0x500A -Non hot-key ACPI HKEY event map: +Non hotkey ACPI HKEY event map: +------------------------------- + +Events that are not propagated by the driver, except for legacy +compatibility purposes when hotkey_report_mode is set to 1: + 0x5001 Lid closed 0x5002 Lid opened 0x5009 Tablet swivel: switched to tablet mode 0x500A Tablet swivel: switched to normal mode 0x7000 Radio Switch may have changed state -The above events are not propagated by the driver, except for legacy -compatibility purposes when hotkey_report_mode is set to 1. +Events that are never propagated by the driver: 0x2304 System is waking up from suspend to undock 0x2305 System is waking up from suspend to eject bay @@ -528,14 +535,39 @@ compatibility purposes when hotkey_report_mode is set to 1. 0x2405 System is waking up from hibernation to eject bay 0x5010 Brightness level changed/control event -The above events are never propagated by the driver. +Events that are propagated by the driver to userspace: +0x2313 ALARM: System is waking up from suspend because + the battery is nearly empty +0x2413 ALARM: System is waking up from hibernation because + the battery is nearly empty 0x3003 Bay ejection (see 0x2x05) complete, can sleep again +0x3006 Bay hotplug request (hint to power up SATA link when + the optical drive tray is ejected) 0x4003 Undocked (see 0x2x04), can sleep again 0x500B Tablet pen inserted into its storage bay 0x500C Tablet pen removed from its storage bay - -The above events are propagated by the driver. +0x6011 ALARM: battery is too hot +0x6012 ALARM: battery is extremely hot +0x6021 ALARM: a sensor is too hot +0x6022 ALARM: a sensor is extremely hot +0x6030 System thermal table changed + +Battery nearly empty alarms are a last resort attempt to get the +operating system to hibernate or shutdown cleanly (0x2313), or shutdown +cleanly (0x2413) before power is lost. They must be acted upon, as the +wake up caused by the firmware will have negated most safety nets... + +When any of the "too hot" alarms happen, according to Lenovo the user +should suspend or hibernate the laptop (and in the case of battery +alarms, unplug the AC adapter) to let it cool down. These alarms do +signal that something is wrong, they should never happen on normal +operating conditions. + +The "extremely hot" alarms are emergencies. According to Lenovo, the +operating system is to force either an immediate suspend or hibernate +cycle, or a system shutdown. Obviously, something is very wrong if this +happens. Compatibility notes: @@ -650,6 +682,10 @@ LCD, CRT or DVI (if available). The following commands are available: echo expand_toggle > /proc/acpi/ibm/video echo video_switch > /proc/acpi/ibm/video +NOTE: Access to this feature is restricted to processes owning the +CAP_SYS_ADMIN capability for safety reasons, as it can interact badly +enough with some versions of X.org to crash it. + Each video output device can be enabled or disabled individually. Reading /proc/acpi/ibm/video shows the status of each device. @@ -924,70 +960,21 @@ Sysfs notes: subsystem, and follow all of the hwmon guidelines at Documentation/hwmon. +EXPERIMENTAL: Embedded controller register dump +----------------------------------------------- -EXPERIMENTAL: Embedded controller register dump -- /proc/acpi/ibm/ecdump ------------------------------------------------------------------------- - -This feature is marked EXPERIMENTAL because the implementation -directly accesses hardware registers and may not work as expected. USE -WITH CAUTION! To use this feature, you need to supply the -experimental=1 parameter when loading the module. - -This feature dumps the values of 256 embedded controller -registers. Values which have changed since the last time the registers -were dumped are marked with a star: - -[root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump -EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f -EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 -EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 -EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 -EC 0x30: 01 07 1a 00 30 04 00 00 *85 00 00 10 00 50 00 00 -EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 -EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 *bc *02 *bc -EC 0x60: *02 *bc *02 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0x70: 00 00 00 00 00 12 30 40 *24 *26 *2c *27 *20 80 *1f 80 -EC 0x80: 00 00 00 06 *37 *0e 03 00 00 00 0e 07 00 00 00 00 -EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xa0: *ff 09 ff 09 ff ff *64 00 *00 *00 *a2 41 *ff *ff *e0 00 -EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 -EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a - -This feature can be used to determine the register holding the fan -speed on some models. To do that, do the following: +This feature is not included in the thinkpad driver anymore. +Instead the EC can be accessed through /sys/kernel/debug/ec with +a userspace tool which can be found here: +ftp://ftp.suse.com/pub/people/trenn/sources/ec +Use it to determine the register holding the fan +speed on some models. To do that, do the following: - make sure the battery is fully charged - make sure the fan is running - - run 'cat /proc/acpi/ibm/ecdump' several times, once per second or so - -The first step makes sure various charging-related values don't -vary. The second ensures that the fan-related values do vary, since -the fan speed fluctuates a bit. The third will (hopefully) mark the -fan register with a star: - -[root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump -EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f -EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 -EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 -EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 -EC 0x30: 01 07 1a 00 30 04 00 00 85 00 00 10 00 50 00 00 -EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 -EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 bc 02 bc -EC 0x60: 02 bc 02 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0x70: 00 00 00 00 00 12 30 40 24 27 2c 27 21 80 1f 80 -EC 0x80: 00 00 00 06 *be 0d 03 00 00 00 0e 07 00 00 00 00 -EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xa0: ff 09 ff 09 ff ff 64 00 00 00 a2 41 ff ff e0 00 -EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 -EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a - -Another set of values that varies often is the temperature + - use above mentioned tool to read out the EC + +Often fan and temperature values vary between readings. Since temperatures don't change vary fast, you can take several quick dumps to eliminate them. @@ -1037,6 +1024,10 @@ ThinkPad-specific interface. The driver will disable its native backlight brightness control interface if it detects that the standard ACPI interface is available in the ThinkPad. +If you want to use the thinkpad-acpi backlight brightness control +instead of the generic ACPI video backlight brightness control for some +reason, you should use the acpi_backlight=vendor kernel parameter. + The brightness_enable module parameter can be used to control whether the LCD brightness control feature will be enabled when available. brightness_enable=0 forces it to be disabled. brightness_enable=1 |