diff options
Diffstat (limited to 'arch/m68knommu/Kconfig')
| -rw-r--r-- | arch/m68knommu/Kconfig | 58 |
1 files changed, 47 insertions, 11 deletions
diff --git a/arch/m68knommu/Kconfig b/arch/m68knommu/Kconfig index 8b9daca..b5424cf 100644 --- a/arch/m68knommu/Kconfig +++ b/arch/m68knommu/Kconfig @@ -3,6 +3,7 @@ config M68K default y select HAVE_IDE select HAVE_GENERIC_HARDIRQS + select GENERIC_HARDIRQS_NO_DEPRECATED config MMU bool @@ -78,6 +79,12 @@ config HAVE_CACHE_SPLIT config HAVE_CACHE_CB bool +config HAVE_MBAR + bool + +config HAVE_IPSBAR + bool + source "init/Kconfig" source "kernel/Kconfig.freezer" @@ -111,12 +118,14 @@ config M68360 config M5206 bool "MCF5206" select COLDFIRE_SW_A7 + select HAVE_MBAR help Motorola ColdFire 5206 processor support. config M5206e bool "MCF5206e" select COLDFIRE_SW_A7 + select HAVE_MBAR help Motorola ColdFire 5206e processor support. @@ -131,30 +140,35 @@ config M523x bool "MCF523x" select GENERIC_CLOCKEVENTS select HAVE_CACHE_SPLIT + select HAVE_IPSBAR help Freescale Coldfire 5230/1/2/4/5 processor support config M5249 bool "MCF5249" select COLDFIRE_SW_A7 + select HAVE_MBAR help Motorola ColdFire 5249 processor support. config M5271 bool "MCF5271" select HAVE_CACHE_SPLIT + select HAVE_IPSBAR help Freescale (Motorola) ColdFire 5270/5271 processor support. config M5272 bool "MCF5272" select COLDFIRE_SW_A7 + select HAVE_MBAR help Motorola ColdFire 5272 processor support. config M5275 bool "MCF5275" select HAVE_CACHE_SPLIT + select HAVE_IPSBAR help Freescale (Motorola) ColdFire 5274/5275 processor support. @@ -162,6 +176,7 @@ config M528x bool "MCF528x" select GENERIC_CLOCKEVENTS select HAVE_CACHE_SPLIT + select HAVE_IPSBAR help Motorola ColdFire 5280/5282 processor support. @@ -169,6 +184,7 @@ config M5307 bool "MCF5307" select COLDFIRE_SW_A7 select HAVE_CACHE_CB + select HAVE_MBAR help Motorola ColdFire 5307 processor support. @@ -182,18 +198,21 @@ config M5407 bool "MCF5407" select COLDFIRE_SW_A7 select HAVE_CACHE_CB + select HAVE_MBAR help Motorola ColdFire 5407 processor support. config M547x bool "MCF547x" select HAVE_CACHE_CB + select HAVE_MBAR help Freescale ColdFire 5470/5471/5472/5473/5474/5475 processor support. config M548x bool "MCF548x" select HAVE_CACHE_CB + select HAVE_MBAR help Freescale ColdFire 5480/5481/5482/5483/5484/5485 processor support. @@ -241,17 +260,6 @@ config CLOCK_FREQ if it is fitted (there are some exceptions). This value will be specific to the exact CPU that you are using. -config CLOCK_DIV - int "Set the core/bus clock divide ratio" - default "1" - depends on CLOCK_SET - help - On many SoC style CPUs the master CPU clock is also used to drive - on-chip peripherals. The clock that is distributed to these - peripherals is sometimes a fixed ratio of the master clock - frequency. If so then set this to the divider ratio of the - master clock to the peripheral clock. If not sure then select 1. - config OLDMASK bool "Old mask 5307 (1H55J) silicon" depends on M5307 @@ -500,6 +508,12 @@ config M5407C3 help Support for the Motorola M5407C3 board. +config FIREBEE + bool "FireBee board support" + depends on M547x + help + Support for the FireBee ColdFire 5475 based board. + config CLEOPATRA bool "Feith CLEOPATRA board support" depends on (M5307 || M5407) @@ -649,6 +663,28 @@ config VECTORBASE platforms this address is programmed into the VBR register, thus actually setting the address to use. +config MBAR + hex "Address of the MBAR (internal peripherals)" + default "0x10000000" + depends on HAVE_MBAR + help + Define the address of the internal system peripherals. This value + is set in the processors MBAR register. This is generally setup by + the boot loader, and will not be written by the kernel. By far most + ColdFire boards use the default 0x10000000 value, so if unsure then + use this. + +config IPSBAR + hex "Address of the IPSBAR (internal peripherals)" + default "0x40000000" + depends on HAVE_IPSBAR + help + Define the address of the internal system peripherals. This value + is set in the processors IPSBAR register. This is generally setup by + the boot loader, and will not be written by the kernel. By far most + ColdFire boards use the default 0x40000000 value, so if unsure then + use this. + config KERNELBASE hex "Address of the base of kernel code" default "0x400" |